From 2e0b80ce4520602b6c1aa806b42a01b7ff7a9af5 Mon Sep 17 00:00:00 2001 From: Amelie Delaunay Date: Thu, 9 May 2019 10:58:50 +0200 Subject: dt-bindings: pinctrl: document the STMFX pinctrl bindings This patch adds documentation of device tree bindings for the STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander. Signed-off-by: Amelie Delaunay Reviewed-by: Linus Walleij Reviewed-by: Rob Herring Signed-off-by: Lee Jones --- .../devicetree/bindings/pinctrl/pinctrl-stmfx.txt | 116 +++++++++++++++++++++ 1 file changed, 116 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt new file mode 100644 index 000000000000..c1b4c1819b84 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt @@ -0,0 +1,116 @@ +STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander bindings + +ST Multi-Function eXpander (STMFX) offers up to 24 GPIOs expansion. +Please refer to ../mfd/stmfx.txt for STMFX Core bindings. + +Required properties: +- compatible: should be "st,stmfx-0300-pinctrl". +- #gpio-cells: should be <2>, the first cell is the GPIO number and the second + cell is the gpio flags in accordance with . +- gpio-controller: marks the device as a GPIO controller. +- #interrupt-cells: should be <2>, the first cell is the GPIO number and the + second cell is the interrupt flags in accordance with + . +- interrupt-controller: marks the device as an interrupt controller. +- gpio-ranges: specifies the mapping between gpio controller and pin + controller pins. Check "Concerning gpio-ranges property" below. +Please refer to ../gpio/gpio.txt. + +Please refer to pinctrl-bindings.txt for pin configuration. + +Required properties for pin configuration sub-nodes: +- pins: list of pins to which the configuration applies. + +Optional properties for pin configuration sub-nodes (pinconf-generic ones): +- bias-disable: disable any bias on the pin. +- bias-pull-up: the pin will be pulled up. +- bias-pull-pin-default: use the pin-default pull state. +- bias-pull-down: the pin will be pulled down. +- drive-open-drain: the pin will be driven with open drain. +- drive-push-pull: the pin will be driven actively high and low. +- output-high: the pin will be configured as an output driving high level. +- output-low: the pin will be configured as an output driving low level. + +Note that STMFX pins[15:0] are called "gpio[15:0]", and STMFX pins[23:16] are +called "agpio[7:0]". Example, to refer to pin 18 of STMFX, use "agpio2". + +Concerning gpio-ranges property: +- if all STMFX pins[24:0] are available (no other STMFX function in use), you + should use gpio-ranges = <&stmfx_pinctrl 0 0 24>; +- if agpio[3:0] are not available (STMFX Touchscreen function in use), you + should use gpio-ranges = <&stmfx_pinctrl 0 0 16>, <&stmfx_pinctrl 20 20 4>; +- if agpio[7:4] are not available (STMFX IDD function in use), you + should use gpio-ranges = <&stmfx_pinctrl 0 0 20>; + + +Example: + + stmfx: stmfx@42 { + ... + + stmfx_pinctrl: stmfx-pin-controller { + compatible = "st,stmfx-0300-pinctrl"; + #gpio-cells = <2>; + #interrupt-cells = <2>; + gpio-controller; + interrupt-controller; + gpio-ranges = <&stmfx_pinctrl 0 0 24>; + + joystick_pins: joystick { + pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4"; + drive-push-pull; + bias-pull-up; + }; + }; + }; + +Example of STMFX GPIO consumers: + + joystick { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&joystick_pins>; + pinctrl-names = "default"; + button-0 { + label = "JoySel"; + linux,code = ; + interrupt-parent = <&stmfx_pinctrl>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; + }; + button-1 { + label = "JoyDown"; + linux,code = ; + interrupt-parent = <&stmfx_pinctrl>; + interrupts = <1 IRQ_TYPE_EDGE_RISING>; + }; + button-2 { + label = "JoyLeft"; + linux,code = ; + interrupt-parent = <&stmfx_pinctrl>; + interrupts = <2 IRQ_TYPE_EDGE_RISING>; + }; + button-3 { + label = "JoyRight"; + linux,code = ; + interrupt-parent = <&stmfx_pinctrl>; + interrupts = <3 IRQ_TYPE_EDGE_RISING>; + }; + button-4 { + label = "JoyUp"; + linux,code = ; + interrupt-parent = <&stmfx_pinctrl>; + interrupts = <4 IRQ_TYPE_EDGE_RISING>; + }; + }; + + leds { + compatible = "gpio-leds"; + orange { + gpios = <&stmfx_pinctrl 17 1>; + }; + + blue { + gpios = <&stmfx_pinctrl 19 1>; + }; + } -- cgit v1.2.3