From f96e6c0ef63b981d295547ef624f4da7c820e097 Mon Sep 17 00:00:00 2001 From: Andy Shevchenko Date: Mon, 17 May 2021 17:03:50 +0300 Subject: spi: pxa2xx: Update documentation to point out that it's outdated Update documentation by pointing out that it's applicable mostly for a legacy platform. While at it, add couple of points with regard to ACPI, Device Tree, and automatic DMA enablement. Signed-off-by: Andy Shevchenko Link: https://lore.kernel.org/r/20210517140351.901-9-andriy.shevchenko@linux.intel.com Signed-off-by: Mark Brown --- Documentation/spi/pxa2xx.rst | 58 ++++++++++++++++++++++++-------------------- 1 file changed, 32 insertions(+), 26 deletions(-) (limited to 'Documentation/spi') diff --git a/Documentation/spi/pxa2xx.rst b/Documentation/spi/pxa2xx.rst index 882d3cc72cc2..6312968acfe9 100644 --- a/Documentation/spi/pxa2xx.rst +++ b/Documentation/spi/pxa2xx.rst @@ -2,43 +2,47 @@ PXA2xx SPI on SSP driver HOWTO ============================== -This a mini howto on the pxa2xx_spi driver. The driver turns a PXA2xx -synchronous serial port into a SPI master controller +This a mini HOWTO on the pxa2xx_spi driver. The driver turns a PXA2xx +synchronous serial port into an SPI master controller (see Documentation/spi/spi-summary.rst). The driver has the following features -- Support for any PXA2xx SSP +- Support for any PXA2xx and compatible SSP. - SSP PIO and SSP DMA data transfers. - External and Internal (SSPFRM) chip selects. - Per slave device (chip) configuration. - Full suspend, freeze, resume support. -The driver is built around a "spi_message" fifo serviced by workqueue and a -tasklet. The workqueue, "pump_messages", drives message fifo and the tasklet -(pump_transfer) is responsible for queuing SPI transactions and setting up and -launching the dma/interrupt driven transfers. +The driver is built around a &struct spi_message FIFO serviced by kernel +thread. The kernel thread, spi_pump_messages(), drives message FIFO and +is responsible for queuing SPI transactions and setting up and launching +the DMA or interrupt driven transfers. Declaring PXA2xx Master Controllers ----------------------------------- -Typically a SPI master is defined in the arch/.../mach-*/board-*.c as a -"platform device". The master configuration is passed to the driver via a table -found in include/linux/spi/pxa2xx_spi.h:: +Typically, for a legacy platform, an SPI master is defined in the +arch/.../mach-*/board-*.c as a "platform device". The master configuration +is passed to the driver via a table found in include/linux/spi/pxa2xx_spi.h:: struct pxa2xx_spi_controller { u16 num_chipselect; u8 enable_dma; + ... }; The "pxa2xx_spi_controller.num_chipselect" field is used to determine the number of slave device (chips) attached to this SPI master. The "pxa2xx_spi_controller.enable_dma" field informs the driver that SSP DMA should -be used. This caused the driver to acquire two DMA channels: rx_channel and -tx_channel. The rx_channel has a higher DMA service priority the tx_channel. +be used. This caused the driver to acquire two DMA channels: Rx channel and +Tx channel. The Rx channel has a higher DMA service priority than the Tx channel. See the "PXA2xx Developer Manual" section "DMA Controller". +For the new platforms the description of the controller and peripheral devices +comes from Device Tree or ACPI. + NSSP MASTER SAMPLE ------------------ -Below is a sample configuration using the PXA255 NSSP:: +Below is a sample configuration using the PXA255 NSSP for a legacy platform:: static struct resource pxa_spi_nssp_resources[] = { [0] = { @@ -79,9 +83,10 @@ Below is a sample configuration using the PXA255 NSSP:: Declaring Slave Devices ----------------------- -Typically each SPI slave (chip) is defined in the arch/.../mach-*/board-*.c -using the "spi_board_info" structure found in "linux/spi/spi.h". See -"Documentation/spi/spi-summary.rst" for additional information. +Typically, for a legacy platform, each SPI slave (chip) is defined in the +arch/.../mach-*/board-*.c using the "spi_board_info" structure found in +"linux/spi/spi.h". See "Documentation/spi/spi-summary.rst" for additional +information. Each slave device attached to the PXA must provide slave specific configuration information via the structure "pxa2xx_spi_chip" found in @@ -101,9 +106,9 @@ device. All fields are optional. }; The "pxa2xx_spi_chip.tx_threshold" and "pxa2xx_spi_chip.rx_threshold" fields are -used to configure the SSP hardware fifo. These fields are critical to the +used to configure the SSP hardware FIFO. These fields are critical to the performance of pxa2xx_spi driver and misconfiguration will result in rx -fifo overruns (especially in PIO mode transfers). Good default values are:: +FIFO overruns (especially in PIO mode transfers). Good default values are:: .tx_threshold = 8, .rx_threshold = 8, @@ -118,7 +123,7 @@ use a value of 8. The driver will determine a reasonable default if dma_burst_size == 0. The "pxa2xx_spi_chip.timeout" fields is used to efficiently handle -trailing bytes in the SSP receiver fifo. The correct value for this field is +trailing bytes in the SSP receiver FIFO. The correct value for this field is dependent on the SPI bus speed ("spi_board_info.max_speed_hz") and the specific slave device. Please note that the PXA2xx SSP 1 does not support trailing byte timeouts and must busy-wait any trailing bytes. @@ -131,19 +136,19 @@ testing. The "pxa2xx_spi_chip.cs_control" field is used to point to a board specific function for asserting/deasserting a slave device chip select. If the field is NULL, the pxa2xx_spi master controller driver assumes that the SSP port is -configured to use SSPFRM instead. +configured to use GPIO or SSPFRM instead. NOTE: the SPI driver cannot control the chip select if SSPFRM is used, so the chipselect is dropped after each spi_transfer. Most devices need chip select -asserted around the complete message. Use SSPFRM as a GPIO (through cs_control) +asserted around the complete message. Use SSPFRM as a GPIO (through a descriptor) to accommodate these chips. NSSP SLAVE SAMPLE ----------------- -The pxa2xx_spi_chip structure is passed to the pxa2xx_spi driver in the -"spi_board_info.controller_data" field. Below is a sample configuration using -the PXA255 NSSP. +For a legacy platform or in some other cases, the pxa2xx_spi_chip structure +is passed to the pxa2xx_spi driver in the "spi_board_info.controller_data" +field. Below is a sample configuration using the PXA255 NSSP. :: @@ -212,7 +217,9 @@ DMA and PIO I/O Support ----------------------- The pxa2xx_spi driver supports both DMA and interrupt driven PIO message transfers. The driver defaults to PIO mode and DMA transfers must be enabled -by setting the "enable_dma" flag in the "pxa2xx_spi_controller" structure. The DMA +by setting the "enable_dma" flag in the "pxa2xx_spi_controller" structure. +For the newer platforms, that are known to support DMA, the driver will enable +it automatically and try it first with a possible fallback to PIO. The DMA mode supports both coherent and stream based DMA mappings. The following logic is used to determine the type of I/O to be used on @@ -236,5 +243,4 @@ a per "spi_transfer" basis:: THANKS TO --------- - David Brownell and others for mentoring the development of this driver. -- cgit v1.2.3