From 128bb95debc8302a999a495dd21726ca422da12a Mon Sep 17 00:00:00 2001 From: Daniel Mack Date: Tue, 15 Jul 2014 09:47:52 -0700 Subject: Input: add driver for Microchip's CAP1106 This patch adds a driver for Microchips CAP1106, an I2C driven, 6-channel capacitive touch sensor. For now, only the capacitive buttons are supported, and no specific settings that can be tweaked for individual channels, except for the device-wide sensitivity gain. The defaults seem to work just fine out of the box, so I'll leave configurable parameters for someone who's in need of them and who can actually measure the impact. All registers are prepared, however. Many of them are just not used for now. The implementation does not make any attempt to be compatible to platform data driven boards, but fully depends on CONFIG_OF. Power management functions are also left for volounteers with the ability to actually test them. Signed-off-by: Daniel Mack Signed-off-by: Dmitry Torokhov --- .../devicetree/bindings/input/cap1106.txt | 53 ++++++++++++++++++++++ 1 file changed, 53 insertions(+) create mode 100644 Documentation/devicetree/bindings/input/cap1106.txt (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/input/cap1106.txt b/Documentation/devicetree/bindings/input/cap1106.txt new file mode 100644 index 000000000000..4b463904cba0 --- /dev/null +++ b/Documentation/devicetree/bindings/input/cap1106.txt @@ -0,0 +1,53 @@ +Device tree bindings for Microchip CAP1106, 6 channel capacitive touch sensor + +The node for this driver must be a child of a I2C controller node, as the +device communication via I2C only. + +Required properties: + + compatible: Must be "microchip,cap1106" + + reg: The I2C slave address of the device. + Only 0x28 is valid. + + interrupts: Property describing the interrupt line the + device's ALERT#/CM_IRQ# pin is connected to. + The device only has one interrupt source. + +Optional properties: + + autorepeat: Enables the Linux input system's autorepeat + feature on the input device. + + microchip,sensor-gain: Defines the gain of the sensor circuitry. This + effectively controls the sensitivity, as a + smaller delta capacitance is required to + generate the same delta count values. + Valid values are 1, 2, 4, and 8. + By default, a gain of 1 is set. + + linux,keycodes: Specifies an array of numeric keycode values to + be used for the channels. If this property is + omitted, KEY_A, KEY_B, etc are used as + defaults. The array must have exactly six + entries. + +Example: + +i2c_controller { + cap1106@28 { + compatible = "microchip,cap1106"; + interrupt-parent = <&gpio1>; + interrupts = <0 0>; + reg = <0x28>; + autorepeat; + microchip,sensor-gain = <2>; + + linux,keycodes = <103 /* KEY_UP */ + 106 /* KEY_RIGHT */ + 108 /* KEY_DOWN */ + 105 /* KEY_LEFT */ + 109 /* KEY_PAGEDOWN */ + 104>; /* KEY_PAGEUP */ + }; +} -- cgit v1.2.3 From 3974037039e925a9645e70e1dc91735d28faad95 Mon Sep 17 00:00:00 2001 From: Heiko Stuebner Date: Mon, 21 Jul 2014 10:02:11 -0700 Subject: Input: zforce - add regulator handling It's possible that the controller has an individually switchable power supply. Therefore add support to control a supplying regulator. As this is not always the case, the regulator is requested as optional. Signed-off-by: Heiko Stuebner Signed-off-by: Dmitry Torokhov --- .../bindings/input/touchscreen/zforce_ts.txt | 4 +++ drivers/input/touchscreen/zforce_ts.c | 31 ++++++++++++++++++++++ 2 files changed, 35 insertions(+) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt index 2faf1f1fa39e..80c37df940a7 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt @@ -9,6 +9,9 @@ Required properties: - x-size: horizontal resolution of touchscreen - y-size: vertical resolution of touchscreen +Optional properties: +- vdd-supply: Regulator controlling the controller supply + Example: i2c@00000000 { @@ -18,6 +21,7 @@ Example: compatible = "neonode,zforce"; reg = <0x50>; interrupts = <2 0>; + vdd-supply = <®_zforce_vdd>; gpios = <&gpio5 6 0>, /* INT */ <&gpio5 9 0>; /* RST */ diff --git a/drivers/input/touchscreen/zforce_ts.c b/drivers/input/touchscreen/zforce_ts.c index feea85b52fa8..8ba48f5eff7b 100644 --- a/drivers/input/touchscreen/zforce_ts.c +++ b/drivers/input/touchscreen/zforce_ts.c @@ -29,6 +29,8 @@ #include #include #include +#include +#include #include #include @@ -117,6 +119,8 @@ struct zforce_ts { const struct zforce_ts_platdata *pdata; char phys[32]; + struct regulator *reg_vdd; + bool suspending; bool suspended; bool boot_complete; @@ -690,6 +694,11 @@ static void zforce_reset(void *data) struct zforce_ts *ts = data; gpio_set_value(ts->pdata->gpio_rst, 0); + + udelay(10); + + if (!IS_ERR(ts->reg_vdd)) + regulator_disable(ts->reg_vdd); } static struct zforce_ts_platdata *zforce_parse_dt(struct device *dev) @@ -765,10 +774,32 @@ static int zforce_probe(struct i2c_client *client, return ret; } + ts->reg_vdd = devm_regulator_get_optional(&client->dev, "vdd"); + if (IS_ERR(ts->reg_vdd)) { + ret = PTR_ERR(ts->reg_vdd); + if (ret == -EPROBE_DEFER) + return ret; + } else { + ret = regulator_enable(ts->reg_vdd); + if (ret) + return ret; + + /* + * according to datasheet add 100us grace time after regular + * regulator enable delay. + */ + udelay(100); + } + ret = devm_add_action(&client->dev, zforce_reset, ts); if (ret) { dev_err(&client->dev, "failed to register reset action, %d\n", ret); + + /* hereafter the regulator will be disabled by the action */ + if (!IS_ERR(ts->reg_vdd)) + regulator_disable(ts->reg_vdd); + return ret; } -- cgit v1.2.3 From 78188be3e5dd59cc2f67bf4cf573e579da186d39 Mon Sep 17 00:00:00 2001 From: Stephen Warren Date: Wed, 23 Jul 2014 12:23:23 -0700 Subject: Input: atmel_mxt_ts - implement device tree support Signed-off-by: Stephen Warren Signed-off-by: Nick Dyer Signed-off-by: Dmitry Torokhov --- .../devicetree/bindings/input/atmel,maxtouch.txt | 25 ++++++++ drivers/input/touchscreen/atmel_mxt_ts.c | 68 ++++++++++++++++++++-- 2 files changed, 88 insertions(+), 5 deletions(-) create mode 100644 Documentation/devicetree/bindings/input/atmel,maxtouch.txt (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt new file mode 100644 index 000000000000..baef432e8369 --- /dev/null +++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt @@ -0,0 +1,25 @@ +Atmel maXTouch touchscreen/touchpad + +Required properties: +- compatible: + atmel,maxtouch + +- reg: The I2C address of the device + +- interrupts: The sink for the touchpad's IRQ output + See ../interrupt-controller/interrupts.txt + +Optional properties for main touchpad device: + +- linux,gpio-keymap: An array of up to 4 entries indicating the Linux + keycode generated by each GPIO. Linux keycodes are defined in + . + +Example: + + touch@4b { + compatible = "atmel,maxtouch"; + reg = <0x4b>; + interrupt-parent = <&gpio>; + interrupts = ; + }; diff --git a/drivers/input/touchscreen/atmel_mxt_ts.c b/drivers/input/touchscreen/atmel_mxt_ts.c index 31113c372f59..4317273c2138 100644 --- a/drivers/input/touchscreen/atmel_mxt_ts.c +++ b/drivers/input/touchscreen/atmel_mxt_ts.c @@ -22,6 +22,7 @@ #include #include #include +#include #include /* Version */ @@ -1527,15 +1528,65 @@ static void mxt_input_close(struct input_dev *dev) mxt_stop(data); } -static int mxt_probe(struct i2c_client *client, - const struct i2c_device_id *id) +#ifdef CONFIG_OF +static struct mxt_platform_data *mxt_parse_dt(struct i2c_client *client) +{ + struct mxt_platform_data *pdata; + u32 *keymap; + u32 keycode; + int proplen, i, ret; + + if (!client->dev.of_node) + return ERR_PTR(-ENODEV); + + pdata = devm_kzalloc(&client->dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return ERR_PTR(-ENOMEM); + + if (of_find_property(client->dev.of_node, "linux,gpio-keymap", + &proplen)) { + pdata->t19_num_keys = proplen / sizeof(u32); + + keymap = devm_kzalloc(&client->dev, + pdata->t19_num_keys * sizeof(keymap[0]), + GFP_KERNEL); + if (!keymap) + return ERR_PTR(-ENOMEM); + + for (i = 0; i < pdata->t19_num_keys; i++) { + ret = of_property_read_u32_index(client->dev.of_node, + "linux,gpio-keymap", i, &keycode); + if (ret) + keycode = KEY_RESERVED; + + keymap[i] = keycode; + } + + pdata->t19_keymap = keymap; + } + + return pdata; +} +#else +static struct mxt_platform_data *mxt_parse_dt(struct i2c_client *client) +{ + dev_dbg(&client->dev, "No platform data specified\n"); + return ERR_PTR(-EINVAL); +} +#endif + +static int mxt_probe(struct i2c_client *client, const struct i2c_device_id *id) { struct mxt_data *data; - const struct mxt_platform_data *pdata = dev_get_platdata(&client->dev); + const struct mxt_platform_data *pdata; int error; - if (!pdata) - return -EINVAL; + pdata = dev_get_platdata(&client->dev); + if (!pdata) { + pdata = mxt_parse_dt(client); + if (IS_ERR(pdata)) + return PTR_ERR(pdata); + } data = kzalloc(sizeof(struct mxt_data), GFP_KERNEL); if (!data) { @@ -1638,6 +1689,12 @@ static int mxt_resume(struct device *dev) static SIMPLE_DEV_PM_OPS(mxt_pm_ops, mxt_suspend, mxt_resume); +static const struct of_device_id mxt_of_match[] = { + { .compatible = "atmel,maxtouch", }, + {}, +}; +MODULE_DEVICE_TABLE(of, mxt_of_match); + static const struct i2c_device_id mxt_id[] = { { "qt602240_ts", 0 }, { "atmel_mxt_ts", 0 }, @@ -1651,6 +1708,7 @@ static struct i2c_driver mxt_driver = { .driver = { .name = "atmel_mxt_ts", .owner = THIS_MODULE, + .of_match_table = of_match_ptr(mxt_of_match), .pm = &mxt_pm_ops, }, .probe = mxt_probe, -- cgit v1.2.3 From a4054596e93048d50502f6c31c853bfeba5acb8e Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 28 Jul 2014 10:05:39 -0700 Subject: Input: pixcir_i2c_ts - add device tree support Provide device tree support and binding information. Also provide support for a new chip "pixcir_tangoc". Signed-off-by: Roger Quadros Signed-off-by: Dmitry Torokhov --- .../bindings/input/touchscreen/pixcir_i2c_ts.txt | 26 ++++++++ .../devicetree/bindings/vendor-prefixes.txt | 1 + drivers/input/touchscreen/pixcir_i2c_ts.c | 77 ++++++++++++++++++++++ 3 files changed, 104 insertions(+) create mode 100644 Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt new file mode 100644 index 000000000000..6e551090f465 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt @@ -0,0 +1,26 @@ +* Pixcir I2C touchscreen controllers + +Required properties: +- compatible: must be "pixcir,pixcir_ts" or "pixcir,pixcir_tangoc" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- attb-gpio: GPIO connected to the ATTB line of the chip +- touchscreen-size-x: horizontal resolution of touchscreen (in pixels) +- touchscreen-size-y: vertical resolution of touchscreen (in pixels) + +Example: + + i2c@00000000 { + /* ... */ + + pixcir_ts@5c { + compatible = "pixcir,pixcir_ts"; + reg = <0x5c>; + interrupts = <2 0>; + attb-gpio = <&gpf 2 0 2>; + touchscreen-size-x = <800>; + touchscreen-size-y = <600>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 46a311e728a8..91bd2287f0c7 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -99,6 +99,7 @@ panasonic Panasonic Corporation phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd plathome Plat'Home Co., Ltd. +pixcir PIXCIR MICROELECTRONICS Co., Ltd powervr PowerVR (deprecated, use img) qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc diff --git a/drivers/input/touchscreen/pixcir_i2c_ts.c b/drivers/input/touchscreen/pixcir_i2c_ts.c index eddda520a1a7..fc49c75317d1 100644 --- a/drivers/input/touchscreen/pixcir_i2c_ts.c +++ b/drivers/input/touchscreen/pixcir_i2c_ts.c @@ -26,6 +26,9 @@ #include #include #include +#include +#include +#include #define PIXCIR_MAX_SLOTS 5 /* Max fingers supported by driver */ @@ -407,16 +410,69 @@ unlock: static SIMPLE_DEV_PM_OPS(pixcir_dev_pm_ops, pixcir_i2c_ts_suspend, pixcir_i2c_ts_resume); +#ifdef CONFIG_OF +static const struct of_device_id pixcir_of_match[]; + +static struct pixcir_ts_platform_data *pixcir_parse_dt(struct device *dev) +{ + struct pixcir_ts_platform_data *pdata; + struct device_node *np = dev->of_node; + const struct of_device_id *match; + + match = of_match_device(of_match_ptr(pixcir_of_match), dev); + if (!match) + return ERR_PTR(-EINVAL); + + pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return ERR_PTR(-ENOMEM); + + pdata->chip = *(const struct pixcir_i2c_chip_data *)match->data; + + pdata->gpio_attb = of_get_named_gpio(np, "attb-gpio", 0); + /* gpio_attb validity is checked in probe */ + + if (of_property_read_u32(np, "touchscreen-size-x", &pdata->x_max)) { + dev_err(dev, "Failed to get touchscreen-size-x property\n"); + return ERR_PTR(-EINVAL); + } + pdata->x_max -= 1; + + if (of_property_read_u32(np, "touchscreen-size-y", &pdata->y_max)) { + dev_err(dev, "Failed to get touchscreen-size-y property\n"); + return ERR_PTR(-EINVAL); + } + pdata->y_max -= 1; + + dev_dbg(dev, "%s: x %d, y %d, gpio %d\n", __func__, + pdata->x_max + 1, pdata->y_max + 1, pdata->gpio_attb); + + return pdata; +} +#else +static struct pixcir_ts_platform_data *pixcir_parse_dt(struct device *dev) +{ + return ERR_PTR(-EINVAL); +} +#endif + static int pixcir_i2c_ts_probe(struct i2c_client *client, const struct i2c_device_id *id) { const struct pixcir_ts_platform_data *pdata = dev_get_platdata(&client->dev); struct device *dev = &client->dev; + struct device_node *np = dev->of_node; struct pixcir_i2c_ts_data *tsdata; struct input_dev *input; int error; + if (np && !pdata) { + pdata = pixcir_parse_dt(dev); + if (IS_ERR(pdata)) + return PTR_ERR(pdata); + } + if (!pdata) { dev_err(&client->dev, "platform data not defined\n"); return -EINVAL; @@ -522,15 +578,36 @@ static int pixcir_i2c_ts_remove(struct i2c_client *client) static const struct i2c_device_id pixcir_i2c_ts_id[] = { { "pixcir_ts", 0 }, + { "pixcir_tangoc", 0 }, { } }; MODULE_DEVICE_TABLE(i2c, pixcir_i2c_ts_id); +#ifdef CONFIG_OF +static const struct pixcir_i2c_chip_data pixcir_ts_data = { + .max_fingers = 2, + /* no hw id support */ +}; + +static const struct pixcir_i2c_chip_data pixcir_tangoc_data = { + .max_fingers = 5, + .has_hw_ids = true, +}; + +static const struct of_device_id pixcir_of_match[] = { + { .compatible = "pixcir,pixcir_ts", .data = &pixcir_ts_data }, + { .compatible = "pixcir,pixcir_tangoc", .data = &pixcir_tangoc_data }, + { } +}; +MODULE_DEVICE_TABLE(of, pixcir_of_match); +#endif + static struct i2c_driver pixcir_i2c_ts_driver = { .driver = { .owner = THIS_MODULE, .name = "pixcir_ts", .pm = &pixcir_dev_pm_ops, + .of_match_table = of_match_ptr(pixcir_of_match), }, .probe = pixcir_i2c_ts_probe, .remove = pixcir_i2c_ts_remove, -- cgit v1.2.3