From 0c6609805b638debcb7d9d44556546b043ded2e9 Mon Sep 17 00:00:00 2001 From: Fabrice Gasnier Date: Wed, 16 May 2018 09:35:57 +0200 Subject: mfd: stm32-timers: Add support for DMAs STM32 Timers can support up to 7 DMA requests: - 4 channels, update, compare and trigger. Optionally request part, or all DMAs from stm32-timers MFD core. Also add routine to implement burst reads using DMA from timer registers. This is exported. So, it can be used by child drivers, PWM capture for instance (but not limited to). Signed-off-by: Fabrice Gasnier Reviewed-by: Benjamin Gaignard Signed-off-by: Lee Jones --- drivers/mfd/stm32-timers.c | 201 ++++++++++++++++++++++++++++++++++++++- include/linux/mfd/stm32-timers.h | 46 +++++++++ 2 files changed, 245 insertions(+), 2 deletions(-) diff --git a/drivers/mfd/stm32-timers.c b/drivers/mfd/stm32-timers.c index 1d347e5dfa79..efcd4b980c94 100644 --- a/drivers/mfd/stm32-timers.c +++ b/drivers/mfd/stm32-timers.c @@ -4,16 +4,156 @@ * Author: Benjamin Gaignard */ +#include #include #include #include #include +#define STM32_TIMERS_MAX_REGISTERS 0x3fc + +/* DIER register DMA enable bits */ +static const u32 stm32_timers_dier_dmaen[STM32_TIMERS_MAX_DMAS] = { + TIM_DIER_CC1DE, + TIM_DIER_CC2DE, + TIM_DIER_CC3DE, + TIM_DIER_CC4DE, + TIM_DIER_UIE, + TIM_DIER_TDE, + TIM_DIER_COMDE +}; + +static void stm32_timers_dma_done(void *p) +{ + struct stm32_timers_dma *dma = p; + struct dma_tx_state state; + enum dma_status status; + + status = dmaengine_tx_status(dma->chan, dma->chan->cookie, &state); + if (status == DMA_COMPLETE) + complete(&dma->completion); +} + +/** + * stm32_timers_dma_burst_read - Read from timers registers using DMA. + * + * Read from STM32 timers registers using DMA on a single event. + * @dev: reference to stm32_timers MFD device + * @buf: DMA'able destination buffer + * @id: stm32_timers_dmas event identifier (ch[1..4], up, trig or com) + * @reg: registers start offset for DMA to read from (like CCRx for capture) + * @num_reg: number of registers to read upon each DMA request, starting @reg. + * @bursts: number of bursts to read (e.g. like two for pwm period capture) + * @tmo_ms: timeout (milliseconds) + */ +int stm32_timers_dma_burst_read(struct device *dev, u32 *buf, + enum stm32_timers_dmas id, u32 reg, + unsigned int num_reg, unsigned int bursts, + unsigned long tmo_ms) +{ + struct stm32_timers *ddata = dev_get_drvdata(dev); + unsigned long timeout = msecs_to_jiffies(tmo_ms); + struct regmap *regmap = ddata->regmap; + struct stm32_timers_dma *dma = &ddata->dma; + size_t len = num_reg * bursts * sizeof(u32); + struct dma_async_tx_descriptor *desc; + struct dma_slave_config config; + dma_cookie_t cookie; + dma_addr_t dma_buf; + u32 dbl, dba; + long err; + int ret; + + /* Sanity check */ + if (id < STM32_TIMERS_DMA_CH1 || id >= STM32_TIMERS_MAX_DMAS) + return -EINVAL; + + if (!num_reg || !bursts || reg > STM32_TIMERS_MAX_REGISTERS || + (reg + num_reg * sizeof(u32)) > STM32_TIMERS_MAX_REGISTERS) + return -EINVAL; + + if (!dma->chans[id]) + return -ENODEV; + mutex_lock(&dma->lock); + + /* Select DMA channel in use */ + dma->chan = dma->chans[id]; + dma_buf = dma_map_single(dev, buf, len, DMA_FROM_DEVICE); + if (dma_mapping_error(dev, dma_buf)) { + ret = -ENOMEM; + goto unlock; + } + + /* Prepare DMA read from timer registers, using DMA burst mode */ + memset(&config, 0, sizeof(config)); + config.src_addr = (dma_addr_t)dma->phys_base + TIM_DMAR; + config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + ret = dmaengine_slave_config(dma->chan, &config); + if (ret) + goto unmap; + + desc = dmaengine_prep_slave_single(dma->chan, dma_buf, len, + DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT); + if (!desc) { + ret = -EBUSY; + goto unmap; + } + + desc->callback = stm32_timers_dma_done; + desc->callback_param = dma; + cookie = dmaengine_submit(desc); + ret = dma_submit_error(cookie); + if (ret) + goto dma_term; + + reinit_completion(&dma->completion); + dma_async_issue_pending(dma->chan); + + /* Setup and enable timer DMA burst mode */ + dbl = FIELD_PREP(TIM_DCR_DBL, bursts - 1); + dba = FIELD_PREP(TIM_DCR_DBA, reg >> 2); + ret = regmap_write(regmap, TIM_DCR, dbl | dba); + if (ret) + goto dma_term; + + /* Clear pending flags before enabling DMA request */ + ret = regmap_write(regmap, TIM_SR, 0); + if (ret) + goto dcr_clr; + + ret = regmap_update_bits(regmap, TIM_DIER, stm32_timers_dier_dmaen[id], + stm32_timers_dier_dmaen[id]); + if (ret) + goto dcr_clr; + + err = wait_for_completion_interruptible_timeout(&dma->completion, + timeout); + if (err == 0) + ret = -ETIMEDOUT; + else if (err < 0) + ret = err; + + regmap_update_bits(regmap, TIM_DIER, stm32_timers_dier_dmaen[id], 0); + regmap_write(regmap, TIM_SR, 0); +dcr_clr: + regmap_write(regmap, TIM_DCR, 0); +dma_term: + dmaengine_terminate_all(dma->chan); +unmap: + dma_unmap_single(dev, dma_buf, len, DMA_FROM_DEVICE); +unlock: + dma->chan = NULL; + mutex_unlock(&dma->lock); + + return ret; +} +EXPORT_SYMBOL_GPL(stm32_timers_dma_burst_read); + static const struct regmap_config stm32_timers_regmap_cfg = { .reg_bits = 32, .val_bits = 32, .reg_stride = sizeof(u32), - .max_register = 0x3fc, + .max_register = STM32_TIMERS_MAX_REGISTERS, }; static void stm32_timers_get_arr_size(struct stm32_timers *ddata) @@ -27,12 +167,45 @@ static void stm32_timers_get_arr_size(struct stm32_timers *ddata) regmap_write(ddata->regmap, TIM_ARR, 0x0); } +static void stm32_timers_dma_probe(struct device *dev, + struct stm32_timers *ddata) +{ + int i; + char name[4]; + + init_completion(&ddata->dma.completion); + mutex_init(&ddata->dma.lock); + + /* Optional DMA support: get valid DMA channel(s) or NULL */ + for (i = STM32_TIMERS_DMA_CH1; i <= STM32_TIMERS_DMA_CH4; i++) { + snprintf(name, ARRAY_SIZE(name), "ch%1d", i + 1); + ddata->dma.chans[i] = dma_request_slave_channel(dev, name); + } + ddata->dma.chans[STM32_TIMERS_DMA_UP] = + dma_request_slave_channel(dev, "up"); + ddata->dma.chans[STM32_TIMERS_DMA_TRIG] = + dma_request_slave_channel(dev, "trig"); + ddata->dma.chans[STM32_TIMERS_DMA_COM] = + dma_request_slave_channel(dev, "com"); +} + +static void stm32_timers_dma_remove(struct device *dev, + struct stm32_timers *ddata) +{ + int i; + + for (i = STM32_TIMERS_DMA_CH1; i < STM32_TIMERS_MAX_DMAS; i++) + if (ddata->dma.chans[i]) + dma_release_channel(ddata->dma.chans[i]); +} + static int stm32_timers_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; struct stm32_timers *ddata; struct resource *res; void __iomem *mmio; + int ret; ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL); if (!ddata) @@ -43,6 +216,9 @@ static int stm32_timers_probe(struct platform_device *pdev) if (IS_ERR(mmio)) return PTR_ERR(mmio); + /* Timer physical addr for DMA */ + ddata->dma.phys_base = res->start; + ddata->regmap = devm_regmap_init_mmio_clk(dev, "int", mmio, &stm32_timers_regmap_cfg); if (IS_ERR(ddata->regmap)) @@ -54,9 +230,29 @@ static int stm32_timers_probe(struct platform_device *pdev) stm32_timers_get_arr_size(ddata); + stm32_timers_dma_probe(dev, ddata); + platform_set_drvdata(pdev, ddata); - return devm_of_platform_populate(&pdev->dev); + ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); + if (ret) + stm32_timers_dma_remove(dev, ddata); + + return ret; +} + +static int stm32_timers_remove(struct platform_device *pdev) +{ + struct stm32_timers *ddata = platform_get_drvdata(pdev); + + /* + * Don't use devm_ here: enfore of_platform_depopulate() happens before + * DMA are released, to avoid race on DMA. + */ + of_platform_depopulate(&pdev->dev); + stm32_timers_dma_remove(&pdev->dev, ddata); + + return 0; } static const struct of_device_id stm32_timers_of_match[] = { @@ -67,6 +263,7 @@ MODULE_DEVICE_TABLE(of, stm32_timers_of_match); static struct platform_driver stm32_timers_driver = { .probe = stm32_timers_probe, + .remove = stm32_timers_remove, .driver = { .name = "stm32-timers", .of_match_table = stm32_timers_of_match, diff --git a/include/linux/mfd/stm32-timers.h b/include/linux/mfd/stm32-timers.h index 2aadab6f34a1..9596d5c58859 100644 --- a/include/linux/mfd/stm32-timers.h +++ b/include/linux/mfd/stm32-timers.h @@ -8,6 +8,8 @@ #define _LINUX_STM32_GPTIMER_H_ #include +#include +#include #include #define TIM_CR1 0x00 /* Control Register 1 */ @@ -27,6 +29,8 @@ #define TIM_CCR3 0x3C /* Capt/Comp Register 3 */ #define TIM_CCR4 0x40 /* Capt/Comp Register 4 */ #define TIM_BDTR 0x44 /* Break and Dead-Time Reg */ +#define TIM_DCR 0x48 /* DMA control register */ +#define TIM_DMAR 0x4C /* DMA register for transfer */ #define TIM_CR1_CEN BIT(0) /* Counter Enable */ #define TIM_CR1_DIR BIT(4) /* Counter Direction */ @@ -36,6 +40,13 @@ #define TIM_SMCR_SMS (BIT(0) | BIT(1) | BIT(2)) /* Slave mode selection */ #define TIM_SMCR_TS (BIT(4) | BIT(5) | BIT(6)) /* Trigger selection */ #define TIM_DIER_UIE BIT(0) /* Update interrupt */ +#define TIM_DIER_UDE BIT(8) /* Update DMA request Enable */ +#define TIM_DIER_CC1DE BIT(9) /* CC1 DMA request Enable */ +#define TIM_DIER_CC2DE BIT(10) /* CC2 DMA request Enable */ +#define TIM_DIER_CC3DE BIT(11) /* CC3 DMA request Enable */ +#define TIM_DIER_CC4DE BIT(12) /* CC4 DMA request Enable */ +#define TIM_DIER_COMDE BIT(13) /* COM DMA request Enable */ +#define TIM_DIER_TDE BIT(14) /* Trigger DMA request Enable */ #define TIM_SR_UIF BIT(0) /* Update interrupt flag */ #define TIM_EGR_UG BIT(0) /* Update Generation */ #define TIM_CCMR_PE BIT(3) /* Channel Preload Enable */ @@ -56,6 +67,8 @@ #define TIM_BDTR_BK2F (BIT(20) | BIT(21) | BIT(22) | BIT(23)) #define TIM_BDTR_BK2E BIT(24) /* Break 2 input enable */ #define TIM_BDTR_BK2P BIT(25) /* Break 2 input polarity */ +#define TIM_DCR_DBA GENMASK(4, 0) /* DMA base addr */ +#define TIM_DCR_DBL GENMASK(12, 8) /* DMA burst len */ #define MAX_TIM_PSC 0xFFFF #define TIM_CR2_MMS_SHIFT 4 @@ -65,9 +78,42 @@ #define TIM_BDTR_BKF_SHIFT 16 #define TIM_BDTR_BK2F_SHIFT 20 +enum stm32_timers_dmas { + STM32_TIMERS_DMA_CH1, + STM32_TIMERS_DMA_CH2, + STM32_TIMERS_DMA_CH3, + STM32_TIMERS_DMA_CH4, + STM32_TIMERS_DMA_UP, + STM32_TIMERS_DMA_TRIG, + STM32_TIMERS_DMA_COM, + STM32_TIMERS_MAX_DMAS, +}; + +/** + * struct stm32_timers_dma - STM32 timer DMA handling. + * @completion: end of DMA transfer completion + * @phys_base: control registers physical base address + * @lock: protect DMA access + * @chan: DMA channel in use + * @chans: DMA channels available for this timer instance + */ +struct stm32_timers_dma { + struct completion completion; + phys_addr_t phys_base; + struct mutex lock; + struct dma_chan *chan; + struct dma_chan *chans[STM32_TIMERS_MAX_DMAS]; +}; + struct stm32_timers { struct clk *clk; struct regmap *regmap; u32 max_arr; + struct stm32_timers_dma dma; /* Only to be used by the parent */ }; + +int stm32_timers_dma_burst_read(struct device *dev, u32 *buf, + enum stm32_timers_dmas id, u32 reg, + unsigned int num_reg, unsigned int bursts, + unsigned long tmo_ms); #endif -- cgit v1.2.3 From 53e38fe73f941291fd20794c15c3bb7b104a4a17 Mon Sep 17 00:00:00 2001 From: Fabrice Gasnier Date: Wed, 16 May 2018 09:35:58 +0200 Subject: pwm: stm32: Add capture support Add support for PMW input mode on pwm-stm32. STM32 timers support period and duty cycle capture as long as they have at least two PWM channels. One capture channel is used for period (rising-edge), one for duty-cycle (falling-edge). When there's only one channel available, only period can be captured. Duty-cycle is simply zero'ed in such a case. Capture requires exclusive access (e.g. no pwm output running at the same time, to protect common prescaler). Timer DMA burst mode (from MFD core) is being used, to take two snapshots of capture registers (upon each period rising edge). Signed-off-by: Fabrice Gasnier Reviewed-by: Benjamin Gaignard Acked-by: Thierry Reding Signed-off-by: Lee Jones --- drivers/pwm/pwm-stm32.c | 176 +++++++++++++++++++++++++++++++++++++++ include/linux/mfd/stm32-timers.h | 11 +++ 2 files changed, 187 insertions(+) diff --git a/drivers/pwm/pwm-stm32.c b/drivers/pwm/pwm-stm32.c index 2708212933f7..ed3961b7b938 100644 --- a/drivers/pwm/pwm-stm32.c +++ b/drivers/pwm/pwm-stm32.c @@ -25,6 +25,7 @@ struct stm32_pwm { struct regmap *regmap; u32 max_arr; bool have_complementary_output; + u32 capture[4] ____cacheline_aligned; /* DMA'able buffer */ }; struct stm32_breakinput { @@ -62,6 +63,178 @@ static int write_ccrx(struct stm32_pwm *dev, int ch, u32 value) return -EINVAL; } +#define TIM_CCER_CC12P (TIM_CCER_CC1P | TIM_CCER_CC2P) +#define TIM_CCER_CC12E (TIM_CCER_CC1E | TIM_CCER_CC2E) +#define TIM_CCER_CC34P (TIM_CCER_CC3P | TIM_CCER_CC4P) +#define TIM_CCER_CC34E (TIM_CCER_CC3E | TIM_CCER_CC4E) + +/* + * Capture using PWM input mode: + * ___ ___ + * TI[1, 2, 3 or 4]: ........._| |________| + * ^0 ^1 ^2 + * . . . + * . . XXXXX + * . . XXXXX | + * . XXXXX . | + * XXXXX . . | + * COUNTER: ______XXXXX . . . |_XXX + * start^ . . . ^stop + * . . . . + * v v . v + * v + * CCR1/CCR3: tx..........t0...........t2 + * CCR2/CCR4: tx..............t1......... + * + * DMA burst transfer: | | + * v v + * DMA buffer: { t0, tx } { t2, t1 } + * DMA done: ^ + * + * 0: IC1/3 snapchot on rising edge: counter value -> CCR1/CCR3 + * + DMA transfer CCR[1/3] & CCR[2/4] values (t0, tx: doesn't care) + * 1: IC2/4 snapchot on falling edge: counter value -> CCR2/CCR4 + * 2: IC1/3 snapchot on rising edge: counter value -> CCR1/CCR3 + * + DMA transfer CCR[1/3] & CCR[2/4] values (t2, t1) + * + * DMA done, compute: + * - Period = t2 - t0 + * - Duty cycle = t1 - t0 + */ +static int stm32_pwm_raw_capture(struct stm32_pwm *priv, struct pwm_device *pwm, + unsigned long tmo_ms, u32 *raw_prd, + u32 *raw_dty) +{ + struct device *parent = priv->chip.dev->parent; + enum stm32_timers_dmas dma_id; + u32 ccen, ccr; + int ret; + + /* Ensure registers have been updated, enable counter and capture */ + regmap_update_bits(priv->regmap, TIM_EGR, TIM_EGR_UG, TIM_EGR_UG); + regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, TIM_CR1_CEN); + + /* Use cc1 or cc3 DMA resp for PWM input channels 1 & 2 or 3 & 4 */ + dma_id = pwm->hwpwm < 2 ? STM32_TIMERS_DMA_CH1 : STM32_TIMERS_DMA_CH3; + ccen = pwm->hwpwm < 2 ? TIM_CCER_CC12E : TIM_CCER_CC34E; + ccr = pwm->hwpwm < 2 ? TIM_CCR1 : TIM_CCR3; + regmap_update_bits(priv->regmap, TIM_CCER, ccen, ccen); + + /* + * Timer DMA burst mode. Request 2 registers, 2 bursts, to get both + * CCR1 & CCR2 (or CCR3 & CCR4) on each capture event. + * We'll get two capture snapchots: { CCR1, CCR2 }, { CCR1, CCR2 } + * or { CCR3, CCR4 }, { CCR3, CCR4 } + */ + ret = stm32_timers_dma_burst_read(parent, priv->capture, dma_id, ccr, 2, + 2, tmo_ms); + if (ret) + goto stop; + + /* Period: t2 - t0 (take care of counter overflow) */ + if (priv->capture[0] <= priv->capture[2]) + *raw_prd = priv->capture[2] - priv->capture[0]; + else + *raw_prd = priv->max_arr - priv->capture[0] + priv->capture[2]; + + /* Duty cycle capture requires at least two capture units */ + if (pwm->chip->npwm < 2) + *raw_dty = 0; + else if (priv->capture[0] <= priv->capture[3]) + *raw_dty = priv->capture[3] - priv->capture[0]; + else + *raw_dty = priv->max_arr - priv->capture[0] + priv->capture[3]; + + if (*raw_dty > *raw_prd) { + /* + * Race beetween PWM input and DMA: it may happen + * falling edge triggers new capture on TI2/4 before DMA + * had a chance to read CCR2/4. It means capture[1] + * contains period + duty_cycle. So, subtract period. + */ + *raw_dty -= *raw_prd; + } + +stop: + regmap_update_bits(priv->regmap, TIM_CCER, ccen, 0); + regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, 0); + + return ret; +} + +static int stm32_pwm_capture(struct pwm_chip *chip, struct pwm_device *pwm, + struct pwm_capture *result, unsigned long tmo_ms) +{ + struct stm32_pwm *priv = to_stm32_pwm_dev(chip); + unsigned long long prd, div, dty; + unsigned long rate; + unsigned int psc = 0; + u32 raw_prd, raw_dty; + int ret = 0; + + mutex_lock(&priv->lock); + + if (active_channels(priv)) { + ret = -EBUSY; + goto unlock; + } + + ret = clk_enable(priv->clk); + if (ret) { + dev_err(priv->chip.dev, "failed to enable counter clock\n"); + goto unlock; + } + + rate = clk_get_rate(priv->clk); + if (!rate) { + ret = -EINVAL; + goto clk_dis; + } + + /* prescaler: fit timeout window provided by upper layer */ + div = (unsigned long long)rate * (unsigned long long)tmo_ms; + do_div(div, MSEC_PER_SEC); + prd = div; + while ((div > priv->max_arr) && (psc < MAX_TIM_PSC)) { + psc++; + div = prd; + do_div(div, psc + 1); + } + regmap_write(priv->regmap, TIM_ARR, priv->max_arr); + regmap_write(priv->regmap, TIM_PSC, psc); + + /* Map TI1 or TI2 PWM input to IC1 & IC2 (or TI3/4 to IC3 & IC4) */ + regmap_update_bits(priv->regmap, + pwm->hwpwm < 2 ? TIM_CCMR1 : TIM_CCMR2, + TIM_CCMR_CC1S | TIM_CCMR_CC2S, pwm->hwpwm & 0x1 ? + TIM_CCMR_CC1S_TI2 | TIM_CCMR_CC2S_TI2 : + TIM_CCMR_CC1S_TI1 | TIM_CCMR_CC2S_TI1); + + /* Capture period on IC1/3 rising edge, duty cycle on IC2/4 falling. */ + regmap_update_bits(priv->regmap, TIM_CCER, pwm->hwpwm < 2 ? + TIM_CCER_CC12P : TIM_CCER_CC34P, pwm->hwpwm < 2 ? + TIM_CCER_CC2P : TIM_CCER_CC4P); + + ret = stm32_pwm_raw_capture(priv, pwm, tmo_ms, &raw_prd, &raw_dty); + if (ret) + goto stop; + + prd = (unsigned long long)raw_prd * (psc + 1) * NSEC_PER_SEC; + result->period = DIV_ROUND_UP_ULL(prd, rate); + dty = (unsigned long long)raw_dty * (psc + 1) * NSEC_PER_SEC; + result->duty_cycle = DIV_ROUND_UP_ULL(dty, rate); +stop: + regmap_write(priv->regmap, TIM_CCER, 0); + regmap_write(priv->regmap, pwm->hwpwm < 2 ? TIM_CCMR1 : TIM_CCMR2, 0); + regmap_write(priv->regmap, TIM_PSC, 0); +clk_dis: + clk_disable(priv->clk); +unlock: + mutex_unlock(&priv->lock); + + return ret; +} + static int stm32_pwm_config(struct stm32_pwm *priv, int ch, int duty_ns, int period_ns) { @@ -230,6 +403,9 @@ static int stm32_pwm_apply_locked(struct pwm_chip *chip, struct pwm_device *pwm, static const struct pwm_ops stm32pwm_ops = { .owner = THIS_MODULE, .apply = stm32_pwm_apply_locked, +#if IS_ENABLED(CONFIG_DMA_ENGINE) + .capture = stm32_pwm_capture, +#endif }; static int stm32_pwm_set_breakinput(struct stm32_pwm *priv, diff --git a/include/linux/mfd/stm32-timers.h b/include/linux/mfd/stm32-timers.h index 9596d5c58859..d46f5500928e 100644 --- a/include/linux/mfd/stm32-timers.h +++ b/include/linux/mfd/stm32-timers.h @@ -51,13 +51,24 @@ #define TIM_EGR_UG BIT(0) /* Update Generation */ #define TIM_CCMR_PE BIT(3) /* Channel Preload Enable */ #define TIM_CCMR_M1 (BIT(6) | BIT(5)) /* Channel PWM Mode 1 */ +#define TIM_CCMR_CC1S (BIT(0) | BIT(1)) /* Capture/compare 1 sel */ +#define TIM_CCMR_IC1PSC GENMASK(3, 2) /* Input capture 1 prescaler */ +#define TIM_CCMR_CC2S (BIT(8) | BIT(9)) /* Capture/compare 2 sel */ +#define TIM_CCMR_IC2PSC GENMASK(11, 10) /* Input capture 2 prescaler */ +#define TIM_CCMR_CC1S_TI1 BIT(0) /* IC1/IC3 selects TI1/TI3 */ +#define TIM_CCMR_CC1S_TI2 BIT(1) /* IC1/IC3 selects TI2/TI4 */ +#define TIM_CCMR_CC2S_TI2 BIT(8) /* IC2/IC4 selects TI2/TI4 */ +#define TIM_CCMR_CC2S_TI1 BIT(9) /* IC2/IC4 selects TI1/TI3 */ #define TIM_CCER_CC1E BIT(0) /* Capt/Comp 1 out Ena */ #define TIM_CCER_CC1P BIT(1) /* Capt/Comp 1 Polarity */ #define TIM_CCER_CC1NE BIT(2) /* Capt/Comp 1N out Ena */ #define TIM_CCER_CC1NP BIT(3) /* Capt/Comp 1N Polarity */ #define TIM_CCER_CC2E BIT(4) /* Capt/Comp 2 out Ena */ +#define TIM_CCER_CC2P BIT(5) /* Capt/Comp 2 Polarity */ #define TIM_CCER_CC3E BIT(8) /* Capt/Comp 3 out Ena */ +#define TIM_CCER_CC3P BIT(9) /* Capt/Comp 3 Polarity */ #define TIM_CCER_CC4E BIT(12) /* Capt/Comp 4 out Ena */ +#define TIM_CCER_CC4P BIT(13) /* Capt/Comp 4 Polarity */ #define TIM_CCER_CCXE (BIT(0) | BIT(4) | BIT(8) | BIT(12)) #define TIM_BDTR_BKE BIT(12) /* Break input enable */ #define TIM_BDTR_BKP BIT(13) /* Break input polarity */ -- cgit v1.2.3 From d66ffb91c374fc500fe666645184e278774bad38 Mon Sep 17 00:00:00 2001 From: Fabrice Gasnier Date: Wed, 16 May 2018 09:35:59 +0200 Subject: pwm: stm32: Improve capture by tuning counter prescaler Currently, capture is based on timeout window to configure prescaler. PWM capture framework provides 1s window at the time of writing. There's place for improvement, after input signal has been captured once: - Finer tune counter clock prescaler, by using 1st capture result (with arbitrary margin). - Do a 2nd capture, with scaled capture window. This increases accuracy, especially at high rates. Signed-off-by: Fabrice Gasnier Reviewed-by: Benjamin Gaignard Acked-by: Thierry Reding Signed-off-by: Lee Jones --- drivers/pwm/pwm-stm32.c | 24 +++++++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-) diff --git a/drivers/pwm/pwm-stm32.c b/drivers/pwm/pwm-stm32.c index ed3961b7b938..9a50acde1e61 100644 --- a/drivers/pwm/pwm-stm32.c +++ b/drivers/pwm/pwm-stm32.c @@ -168,7 +168,7 @@ static int stm32_pwm_capture(struct pwm_chip *chip, struct pwm_device *pwm, struct stm32_pwm *priv = to_stm32_pwm_dev(chip); unsigned long long prd, div, dty; unsigned long rate; - unsigned int psc = 0; + unsigned int psc = 0, scale; u32 raw_prd, raw_dty; int ret = 0; @@ -219,6 +219,28 @@ static int stm32_pwm_capture(struct pwm_chip *chip, struct pwm_device *pwm, if (ret) goto stop; + /* + * Got a capture. Try to improve accuracy at high rates: + * - decrease counter clock prescaler, scale up to max rate. + */ + if (raw_prd) { + u32 max_arr = priv->max_arr - 0x1000; /* arbitrary margin */ + + scale = max_arr / min(max_arr, raw_prd); + } else { + scale = priv->max_arr; /* bellow resolution, use max scale */ + } + + if (psc && scale > 1) { + /* 2nd measure with new scale */ + psc /= scale; + regmap_write(priv->regmap, TIM_PSC, psc); + ret = stm32_pwm_raw_capture(priv, pwm, tmo_ms, &raw_prd, + &raw_dty); + if (ret) + goto stop; + } + prd = (unsigned long long)raw_prd * (psc + 1) * NSEC_PER_SEC; result->period = DIV_ROUND_UP_ULL(prd, rate); dty = (unsigned long long)raw_dty * (psc + 1) * NSEC_PER_SEC; -- cgit v1.2.3 From ab3a897847834bf3e864fb07b733c444895a24ba Mon Sep 17 00:00:00 2001 From: Fabrice Gasnier Date: Wed, 16 May 2018 09:36:00 +0200 Subject: pwm: stm32: Use input prescaler to improve period capture Using input prescaler, capture unit will trigger DMA once every configurable /2, /4 or /8 events (rising edge). This helps improve period (only) capture accuracy at high rates. Signed-off-by: Fabrice Gasnier Reviewed-by: Benjamin Gaignard Acked-by: Thierry Reding Signed-off-by: Lee Jones --- drivers/pwm/pwm-stm32.c | 63 ++++++++++++++++++++++++++++++++++++++-- include/linux/mfd/stm32-timers.h | 1 + 2 files changed, 62 insertions(+), 2 deletions(-) diff --git a/drivers/pwm/pwm-stm32.c b/drivers/pwm/pwm-stm32.c index 9a50acde1e61..60bfc07c4912 100644 --- a/drivers/pwm/pwm-stm32.c +++ b/drivers/pwm/pwm-stm32.c @@ -8,6 +8,7 @@ * pwm-atmel.c from Bo Shen */ +#include #include #include #include @@ -168,7 +169,7 @@ static int stm32_pwm_capture(struct pwm_chip *chip, struct pwm_device *pwm, struct stm32_pwm *priv = to_stm32_pwm_dev(chip); unsigned long long prd, div, dty; unsigned long rate; - unsigned int psc = 0, scale; + unsigned int psc = 0, icpsc, scale; u32 raw_prd, raw_dty; int ret = 0; @@ -222,6 +223,7 @@ static int stm32_pwm_capture(struct pwm_chip *chip, struct pwm_device *pwm, /* * Got a capture. Try to improve accuracy at high rates: * - decrease counter clock prescaler, scale up to max rate. + * - use input prescaler, capture once every /2 /4 or /8 edges. */ if (raw_prd) { u32 max_arr = priv->max_arr - 0x1000; /* arbitrary margin */ @@ -241,8 +243,65 @@ static int stm32_pwm_capture(struct pwm_chip *chip, struct pwm_device *pwm, goto stop; } + /* Compute intermediate period not to exceed timeout at low rates */ prd = (unsigned long long)raw_prd * (psc + 1) * NSEC_PER_SEC; - result->period = DIV_ROUND_UP_ULL(prd, rate); + do_div(prd, rate); + + for (icpsc = 0; icpsc < MAX_TIM_ICPSC ; icpsc++) { + /* input prescaler: also keep arbitrary margin */ + if (raw_prd >= (priv->max_arr - 0x1000) >> (icpsc + 1)) + break; + if (prd >= (tmo_ms * NSEC_PER_MSEC) >> (icpsc + 2)) + break; + } + + if (!icpsc) + goto done; + + /* Last chance to improve period accuracy, using input prescaler */ + regmap_update_bits(priv->regmap, + pwm->hwpwm < 2 ? TIM_CCMR1 : TIM_CCMR2, + TIM_CCMR_IC1PSC | TIM_CCMR_IC2PSC, + FIELD_PREP(TIM_CCMR_IC1PSC, icpsc) | + FIELD_PREP(TIM_CCMR_IC2PSC, icpsc)); + + ret = stm32_pwm_raw_capture(priv, pwm, tmo_ms, &raw_prd, &raw_dty); + if (ret) + goto stop; + + if (raw_dty >= (raw_prd >> icpsc)) { + /* + * We may fall here using input prescaler, when input + * capture starts on high side (before falling edge). + * Example with icpsc to capture on each 4 events: + * + * start 1st capture 2nd capture + * v v v + * ___ _____ _____ _____ _____ ____ + * TI1..4 |__| |__| |__| |__| |__| + * v v . . . . . v v + * icpsc1/3: . 0 . 1 . 2 . 3 . 0 + * icpsc2/4: 0 1 2 3 0 + * v v v v + * CCR1/3 ......t0..............................t2 + * CCR2/4 ..t1..............................t1'... + * . . . + * Capture0: .<----------------------------->. + * Capture1: .<-------------------------->. . + * . . . + * Period: .<------> . . + * Low side: .<>. + * + * Result: + * - Period = Capture0 / icpsc + * - Duty = Period - Low side = Period - (Capture0 - Capture1) + */ + raw_dty = (raw_prd >> icpsc) - (raw_prd - raw_dty); + } + +done: + prd = (unsigned long long)raw_prd * (psc + 1) * NSEC_PER_SEC; + result->period = DIV_ROUND_UP_ULL(prd, rate << icpsc); dty = (unsigned long long)raw_dty * (psc + 1) * NSEC_PER_SEC; result->duty_cycle = DIV_ROUND_UP_ULL(dty, rate); stop: diff --git a/include/linux/mfd/stm32-timers.h b/include/linux/mfd/stm32-timers.h index d46f5500928e..9da1d7ece079 100644 --- a/include/linux/mfd/stm32-timers.h +++ b/include/linux/mfd/stm32-timers.h @@ -82,6 +82,7 @@ #define TIM_DCR_DBL GENMASK(12, 8) /* DMA burst len */ #define MAX_TIM_PSC 0xFFFF +#define MAX_TIM_ICPSC 0x3 #define TIM_CR2_MMS_SHIFT 4 #define TIM_CR2_MMS2_SHIFT 20 #define TIM_SMCR_TS_SHIFT 4 -- cgit v1.2.3 From acc8e22f5d41558c90519aadc011b6d2839aedfe Mon Sep 17 00:00:00 2001 From: Fabrice Gasnier Date: Wed, 16 May 2018 09:35:56 +0200 Subject: dt-bindings: mfd: stm32-timers: Add support for dmas Add support for DMAs to STM32 timers. STM32 Timers can support up to 7 dma requests: up to 4 channels, update, compare and trigger. DMAs may be used to transfer data from pwm capture for instance. DMA support is made optional, PWM capture support is also an option. This is much more wise system-wide to avoid shortage on DMA request lines as there's significant amount of timer instances that can request up to 7 channels. Signed-off-by: Fabrice Gasnier Reviewed-by: Rob Herring Reviewed-by: Benjamin Gaignard Signed-off-by: Lee Jones --- .../devicetree/bindings/mfd/stm32-timers.txt | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/Documentation/devicetree/bindings/mfd/stm32-timers.txt b/Documentation/devicetree/bindings/mfd/stm32-timers.txt index 1db6e0057a63..0e900b52e895 100644 --- a/Documentation/devicetree/bindings/mfd/stm32-timers.txt +++ b/Documentation/devicetree/bindings/mfd/stm32-timers.txt @@ -19,6 +19,11 @@ Required parameters: Optional parameters: - resets: Phandle to the parent reset controller. See ../reset/st,stm32-rcc.txt +- dmas: List of phandle to dma channels that can be used for + this timer instance. There may be up to 7 dma channels. +- dma-names: List of dma names. Must match 'dmas' property. Valid + names are: "ch1", "ch2", "ch3", "ch4", "up", "trig", + "com". Optional subnodes: - pwm: See ../pwm/pwm-stm32.txt @@ -44,3 +49,18 @@ Example: reg = <0>; }; }; + +Example with all dmas: + timer@40010000 { + ... + dmas = <&dmamux1 11 0x400 0x0>, + <&dmamux1 12 0x400 0x0>, + <&dmamux1 13 0x400 0x0>, + <&dmamux1 14 0x400 0x0>, + <&dmamux1 15 0x400 0x0>, + <&dmamux1 16 0x400 0x0>, + <&dmamux1 17 0x400 0x0>; + dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig", "com"; + ... + child nodes... + }; -- cgit v1.2.3