From 0efc898a9bea7a2e8e583c6efab0e19dc7093078 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Fri, 16 Oct 2015 12:32:32 -0700 Subject: ARM: dts: Fix WLAN regression on omap5-uevm Commit 99f84cae43df ("ARM: dts: add wl12xx/wl18xx bindings") added device tree bindings for the TI WLAN SDIO on many omap variants. I recall wondering how come omap5-uevm did not have the WLAN added and this issue has been bugging me for a while now, and I finally tracked it down to a bad pinmux regression, and a missing deferred probe handling for the 32k clock from palmas that's requested by twl6040. Basically 392adaf796b9 ("ARM: dts: omap5-evm: Add mcspi data") added pin muxing for mcspi4 that conflicts with the onboard WLAN. While some omap5-uevm don't have WLAN populated, the pins are not reused for other devices. And as the SDIO bus should be probed, let's try to enable WLAN by default. Let's fix the regression and add the WLAN configuration as done for the other boards in 99f84cae43df ("ARM: dts: add wl12xx/wl18xx bindings"). And let's use the new MMC pwrseq for the 32k clock as suggested by Javier Martinez Canillas . Note that without a related deferred probe fix for twl6040, the 32k clock is not initialized if palmas-clk is a module and twl6040 is built-in. Let's also use the generic "non-removable" instead of the legacy "ti,non-removable" property while at it. And finally, note that omap5 seems to require WAKEUP_EN for the WLAN GPIO interrupt. Fixes: 392adaf796b9 ("ARM: dts: omap5-evm: Add mcspi data") Cc: Sourav Poddar Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-uevm.dts | 66 +++++++++++++++++++++++++++++++++------- 1 file changed, 55 insertions(+), 11 deletions(-) diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 4da9e52f147b..f10b42fa15c6 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -31,6 +31,24 @@ regulator-max-microvolt = <3000000>; }; + mmc3_pwrseq: sdhci0_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&clk32kgaudio>; + clock-names = "ext_clock"; + }; + + vmmcsdio_fixed: fixedregulator-mmcsdio { + compatible = "regulator-fixed"; + regulator-name = "vmmcsdio_fixed"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */ + enable-active-high; + startup-delay-us = <70000>; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_pins>; + }; + /* HS USB Host PHY on PORT 2 */ hsusb2_phy: hsusb2_phy { compatible = "usb-nop-xceiv"; @@ -197,12 +215,20 @@ >; }; - mcspi4_pins: pinmux_mcspi4_pins { + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */ + OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */ + OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */ + OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */ + OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */ + OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */ + >; + }; + + wlan_pins: pinmux_wlan_pins { pinctrl-single,pins = < - 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi4_clk */ - 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi4_simo */ - 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi4_somi */ - 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi4_cs0 */ + OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */ >; }; @@ -276,6 +302,12 @@ 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ >; }; + + wlcore_irq_pin: pinmux_wlcore_irq_pin { + pinctrl-single,pins = < + OMAP5_IOPAD(0x040, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */ + >; + }; }; &mmc1 { @@ -290,8 +322,25 @@ }; &mmc3 { + vmmc-supply = <&vmmcsdio_fixed>; + mmc-pwrseq = <&mmc3_pwrseq>; bus-width = <4>; - ti,non-removable; + non-removable; + cap-power-off-card; + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>; + interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH + &omap5_pmx_core 0x168>; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1271"; + reg = <2>; + interrupt-parent = <&gpio1>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */ + ref-clock-frequency = <26000000>; + }; }; &mmc4 { @@ -598,11 +647,6 @@ pinctrl-0 = <&mcspi3_pins>; }; -&mcspi4 { - pinctrl-names = "default"; - pinctrl-0 = <&mcspi4_pins>; -}; - &uart1 { pinctrl-names = "default"; pinctrl-0 = <&uart1_pins>; -- cgit v1.2.3 From ee9a97dbeeddc8d4d3b3c69400faa2e594f45b4a Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Fri, 16 Oct 2015 12:32:32 -0700 Subject: ARM: dts: Move most of omap5-uevm.dts to omap5-board-common.dtsi Looks like thevarious omap5-uevm models and igepv5 are very similar. So let's create omap5-board-common.dtsi to allow fixing up things properly for mainline kernel to support all these. Even if we eventually end up having only PMIC + MMC + eMMC + SDIO WLAN + SATA + USB + HDMI configuration in the omap5-board-common.dtsi, this is the easiest way to add support for other boards rather than diffing various versions of out of tree dts files. My guess is that also omap5-sbc-t54.dts can use this, but I don't have that board so that will need to be dealt with later on. Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-board-common.dtsi | 655 +++++++++++++++++++++++++++++ arch/arm/boot/dts/omap5-uevm.dts | 662 +----------------------------- 2 files changed, 669 insertions(+), 648 deletions(-) create mode 100644 arch/arm/boot/dts/omap5-board-common.dtsi diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi new file mode 100644 index 000000000000..5cf76a1c5c75 --- /dev/null +++ b/arch/arm/boot/dts/omap5-board-common.dtsi @@ -0,0 +1,655 @@ +/* + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include "omap5.dtsi" +#include +#include + +/ { + aliases { + display0 = &hdmi0; + }; + + vmmcsd_fixed: fixedregulator-mmcsd { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + mmc3_pwrseq: sdhci0_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&clk32kgaudio>; + clock-names = "ext_clock"; + }; + + vmmcsdio_fixed: fixedregulator-mmcsdio { + compatible = "regulator-fixed"; + regulator-name = "vmmcsdio_fixed"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */ + enable-active-high; + startup-delay-us = <70000>; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_pins>; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */ + clocks = <&auxclk1_ck>; + clock-names = "main_clk"; + clock-frequency = <19200000>; + }; + + /* HS USB Host PHY on PORT 3 */ + hsusb3_phy: hsusb3_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */ + }; + + leds { + compatible = "gpio-leds"; + led@1 { + label = "omap5:blue:usr1"; + gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + }; + + tpd12s015: encoder@0 { + compatible = "ti,tpd12s015"; + + pinctrl-names = "default"; + pinctrl-0 = <&tpd12s015_pins>; + + /* gpios defined in the board specific dts */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tpd12s015_in: endpoint@0 { + remote-endpoint = <&hdmi_out>; + }; + }; + + port@1 { + reg = <1>; + + tpd12s015_out: endpoint@0 { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; + + hdmi0: connector@0 { + compatible = "hdmi-connector"; + label = "hdmi"; + + type = "b"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&tpd12s015_out>; + }; + }; + }; + + sound: sound { + compatible = "ti,abe-twl6040"; + ti,model = "omap5-uevm"; + + ti,mclk-freq = <19200000>; + + ti,mcpdm = <&mcpdm>; + + ti,twl6040 = <&twl6040>; + + /* Audio routing */ + ti,audio-routing = + "Headset Stereophone", "HSOL", + "Headset Stereophone", "HSOR", + "Line Out", "AUXL", + "Line Out", "AUXR", + "HSMIC", "Headset Mic", + "Headset Mic", "Headset Mic Bias", + "AFML", "Line In", + "AFMR", "Line In"; + }; +}; + +&omap5_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &usbhost_pins + &led_gpio_pins + >; + + twl6040_pins: pinmux_twl6040_pins { + pinctrl-single,pins = < + 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ + >; + }; + + mcpdm_pins: pinmux_mcpdm_pins { + pinctrl-single,pins = < + 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ + 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */ + 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */ + 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */ + 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */ + >; + }; + + mcbsp1_pins: pinmux_mcbsp1_pins { + pinctrl-single,pins = < + 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ + 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */ + 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */ + 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */ + >; + }; + + mcbsp2_pins: pinmux_mcbsp2_pins { + pinctrl-single,pins = < + 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */ + 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */ + 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */ + 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ + >; + }; + + mcspi2_pins: pinmux_mcspi2_pins { + pinctrl-single,pins = < + 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ + 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ + 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ + 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ + >; + }; + + mcspi3_pins: pinmux_mcspi3_pins { + pinctrl-single,pins = < + 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ + 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ + 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ + 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */ + OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */ + OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */ + OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */ + OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */ + OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */ + >; + }; + + wlan_pins: pinmux_wlan_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */ + >; + }; + + usbhost_pins: pinmux_usbhost_pins { + pinctrl-single,pins = < + 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ + 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ + + 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ + 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ + + 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */ + 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */ + >; + }; + + led_gpio_pins: pinmux_led_gpio_pins { + pinctrl-single,pins = < + 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */ + >; + }; + + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */ + 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */ + 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */ + 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */ + 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */ + >; + }; + + uart5_pins: pinmux_uart5_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */ + 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */ + 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */ + 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */ + >; + }; + + dss_hdmi_pins: pinmux_dss_hdmi_pins { + pinctrl-single,pins = < + 0x0fc (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + 0x100 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */ + 0x102 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */ + >; + }; + + tpd12s015_pins: pinmux_tpd12s015_pins { + pinctrl-single,pins = < + 0x0fe (PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ + >; + }; +}; + +&omap5_pmx_wkup { + pinctrl-names = "default"; + pinctrl-0 = < + &usbhost_wkup_pins + >; + + usbhost_wkup_pins: pinmux_usbhost_wkup_pins { + pinctrl-single,pins = < + 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ + >; + }; + + wlcore_irq_pin: pinmux_wlcore_irq_pin { + pinctrl-single,pins = < + OMAP5_IOPAD(0x040, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */ + >; + }; +}; + +&mmc1 { + vmmc-supply = <&ldo9_reg>; + bus-width = <4>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <8>; + ti,non-removable; +}; + +&mmc3 { + vmmc-supply = <&vmmcsdio_fixed>; + mmc-pwrseq = <&mmc3_pwrseq>; + bus-width = <4>; + non-removable; + cap-power-off-card; + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>; + interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH + &omap5_pmx_core 0x168>; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1271"; + reg = <2>; + interrupt-parent = <&gpio1>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */ + ref-clock-frequency = <26000000>; + }; +}; + +&mmc4 { + status = "disabled"; +}; + +&mmc5 { + status = "disabled"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + clock-frequency = <400000>; + + palmas: palmas@48 { + compatible = "ti,palmas"; + interrupts = ; /* IRQ_SYS_1N */ + reg = <0x48>; + interrupt-controller; + #interrupt-cells = <2>; + ti,system-power-controller; + + extcon_usb3: palmas_usb { + compatible = "ti,palmas-usb-vid"; + ti,enable-vbus-detection; + ti,enable-id-detection; + ti,wakeup; + }; + + clk32kgaudio: palmas_clk32k@1 { + compatible = "ti,palmas-clk32kgaudio"; + #clock-cells = <0>; + }; + + palmas_pmic { + compatible = "ti,palmas-pmic"; + interrupt-parent = <&palmas>; + interrupts = <14 IRQ_TYPE_NONE>; + interrupt-name = "short-irq"; + + ti,ldo6-vibrator; + + regulators { + smps123_reg: smps123 { + /* VDD_OPP_MPU */ + regulator-name = "smps123"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + smps45_reg: smps45 { + /* VDD_OPP_MM */ + regulator-name = "smps45"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1310000>; + regulator-always-on; + regulator-boot-on; + }; + + smps6_reg: smps6 { + /* VDD_DDR3 - over VDD_SMPS6 */ + regulator-name = "smps6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + smps7_reg: smps7 { + /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ + regulator-name = "smps7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + smps8_reg: smps8 { + /* VDD_OPP_CORE */ + regulator-name = "smps8"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1310000>; + regulator-always-on; + regulator-boot-on; + }; + + smps9_reg: smps9 { + /* VDDA_2v1_AUD over VDD_2v1 */ + regulator-name = "smps9"; + regulator-min-microvolt = <2100000>; + regulator-max-microvolt = <2100000>; + ti,smps-range = <0x80>; + }; + + smps10_out2_reg: smps10_out2 { + /* VBUS_5V_OTG */ + regulator-name = "smps10_out2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + smps10_out1_reg: smps10_out1 { + /* VBUS_5V_OTG */ + regulator-name = "smps10_out1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + ldo1_reg: ldo1 { + /* VDDAPHY_CAM: vdda_csiport */ + regulator-name = "ldo1"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + }; + + ldo2_reg: ldo2 { + /* VCC_2V8_DISP: Does not go anywhere */ + regulator-name = "ldo2"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + /* Unused */ + status = "disabled"; + }; + + ldo3_reg: ldo3 { + /* VDDAPHY_MDM: vdda_lli */ + regulator-name = "ldo3"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + /* Only if Modem is used */ + status = "disabled"; + }; + + ldo4_reg: ldo4 { + /* VDDAPHY_DISP: vdda_dsiport/hdmi */ + regulator-name = "ldo4"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + }; + + ldo5_reg: ldo5 { + /* VDDA_1V8_PHY: usb/sata/hdmi.. */ + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo6_reg: ldo6 { + /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ + regulator-name = "ldo6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo7_reg: ldo7 { + /* VDD_VPP: vpp1 */ + regulator-name = "ldo7"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + /* Only for efuse reprograming! */ + status = "disabled"; + }; + + ldo8_reg: ldo8 { + /* VDD_3v0: Does not go anywhere */ + regulator-name = "ldo8"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + /* Unused */ + status = "disabled"; + }; + + ldo9_reg: ldo9 { + /* VCC_DV_SDIO: vdds_sdcard */ + regulator-name = "ldo9"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + }; + + ldoln_reg: ldoln { + /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ + regulator-name = "ldoln"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldousb_reg: ldousb { + /* VDDA_3V_USB: VDDA_USBHS33 */ + regulator-name = "ldousb"; + regulator-min-microvolt = <3250000>; + regulator-max-microvolt = <3250000>; + regulator-always-on; + regulator-boot-on; + }; + + regen3_reg: regen3 { + /* REGEN3 controls LDO9 supply to card */ + regulator-name = "regen3"; + regulator-always-on; + regulator-boot-on; + }; + }; + }; + + palmas_power_button: palmas_power_button { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&palmas>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + }; + }; + + twl6040: twl@4b { + compatible = "ti,twl6040"; + reg = <0x4b>; + + pinctrl-names = "default"; + pinctrl-0 = <&twl6040_pins>; + + interrupts = ; /* IRQ_SYS_2N cascaded to gic */ + ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; /* gpio line 141 */ + + vio-supply = <&smps7_reg>; + v2v1-supply = <&smps9_reg>; + enable-active-high; + + clocks = <&clk32kgaudio>; + clock-names = "clk32k"; + }; +}; + +&mcpdm { + pinctrl-names = "default"; + pinctrl-0 = <&mcpdm_pins>; + status = "okay"; +}; + +&mcbsp1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp1_pins>; + status = "okay"; +}; + +&mcbsp2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp2_pins>; + status = "okay"; +}; + +&usbhshost { + port2-mode = "ehci-hsic"; + port3-mode = "ehci-hsic"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy &hsusb3_phy>; +}; + +&usb3 { + extcon = <&extcon_usb3>; + vbus-supply = <&smps10_out1_reg>; +}; + +&mcspi1 { + +}; + +&mcspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi2_pins>; +}; + +&mcspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi3_pins>; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, + <&omap5_pmx_core 0x19c>; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&uart5_pins>; +}; + +&cpu0 { + cpu0-supply = <&smps123_reg>; +}; + +&dss { + status = "ok"; +}; + +&hdmi { + status = "ok"; + + /* vdda-supply populated in board specific dts file */ + + pinctrl-names = "default"; + pinctrl-0 = <&dss_hdmi_pins>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&tpd12s015_in>; + }; + }; +}; diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index f10b42fa15c6..05b1c1ebded8 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -7,9 +7,7 @@ */ /dts-v1/; -#include "omap5.dtsi" -#include -#include +#include "omap5-board-common.dtsi" / { model = "TI OMAP5 uEVM board"; @@ -19,572 +17,10 @@ device_type = "memory"; reg = <0x80000000 0x7F000000>; /* 2032 MB */ }; - - aliases { - display0 = &hdmi0; - }; - - vmmcsd_fixed: fixedregulator-mmcsd { - compatible = "regulator-fixed"; - regulator-name = "vmmcsd_fixed"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - }; - - mmc3_pwrseq: sdhci0_pwrseq { - compatible = "mmc-pwrseq-simple"; - clocks = <&clk32kgaudio>; - clock-names = "ext_clock"; - }; - - vmmcsdio_fixed: fixedregulator-mmcsdio { - compatible = "regulator-fixed"; - regulator-name = "vmmcsdio_fixed"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */ - enable-active-high; - startup-delay-us = <70000>; - pinctrl-names = "default"; - pinctrl-0 = <&wlan_pins>; - }; - - /* HS USB Host PHY on PORT 2 */ - hsusb2_phy: hsusb2_phy { - compatible = "usb-nop-xceiv"; - reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */ - clocks = <&auxclk1_ck>; - clock-names = "main_clk"; - clock-frequency = <19200000>; - }; - - /* HS USB Host PHY on PORT 3 */ - hsusb3_phy: hsusb3_phy { - compatible = "usb-nop-xceiv"; - reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */ - }; - - leds { - compatible = "gpio-leds"; - led@1 { - label = "omap5:blue:usr1"; - gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */ - linux,default-trigger = "heartbeat"; - default-state = "off"; - }; - }; - - tpd12s015: encoder@0 { - compatible = "ti,tpd12s015"; - - pinctrl-names = "default"; - pinctrl-0 = <&tpd12s015_pins>; - - gpios = <&gpio9 0 GPIO_ACTIVE_HIGH>, /* TCA6424A P01, CT CP HPD */ - <&gpio9 1 GPIO_ACTIVE_HIGH>, /* TCA6424A P00, LS OE */ - <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */ - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - - tpd12s015_in: endpoint@0 { - remote-endpoint = <&hdmi_out>; - }; - }; - - port@1 { - reg = <1>; - - tpd12s015_out: endpoint@0 { - remote-endpoint = <&hdmi_connector_in>; - }; - }; - }; - }; - - hdmi0: connector@0 { - compatible = "hdmi-connector"; - label = "hdmi"; - - type = "b"; - - port { - hdmi_connector_in: endpoint { - remote-endpoint = <&tpd12s015_out>; - }; - }; - }; - - sound: sound { - compatible = "ti,abe-twl6040"; - ti,model = "omap5-uevm"; - - ti,mclk-freq = <19200000>; - - ti,mcpdm = <&mcpdm>; - - ti,twl6040 = <&twl6040>; - - /* Audio routing */ - ti,audio-routing = - "Headset Stereophone", "HSOL", - "Headset Stereophone", "HSOR", - "Line Out", "AUXL", - "Line Out", "AUXR", - "HSMIC", "Headset Mic", - "Headset Mic", "Headset Mic Bias", - "AFML", "Line In", - "AFMR", "Line In"; - }; -}; - -&omap5_pmx_core { - pinctrl-names = "default"; - pinctrl-0 = < - &usbhost_pins - &led_gpio_pins - >; - - twl6040_pins: pinmux_twl6040_pins { - pinctrl-single,pins = < - 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ - >; - }; - - mcpdm_pins: pinmux_mcpdm_pins { - pinctrl-single,pins = < - 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ - 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */ - 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */ - 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */ - 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */ - >; - }; - - mcbsp1_pins: pinmux_mcbsp1_pins { - pinctrl-single,pins = < - 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ - 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */ - 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */ - 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */ - >; - }; - - mcbsp2_pins: pinmux_mcbsp2_pins { - pinctrl-single,pins = < - 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */ - 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */ - 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */ - 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */ - >; - }; - - i2c1_pins: pinmux_i2c1_pins { - pinctrl-single,pins = < - 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ - 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ - >; - }; - - i2c5_pins: pinmux_i2c5_pins { - pinctrl-single,pins = < - 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */ - 0x188 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */ - >; - }; - - mcspi2_pins: pinmux_mcspi2_pins { - pinctrl-single,pins = < - 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ - 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ - 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ - 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ - >; - }; - - mcspi3_pins: pinmux_mcspi3_pins { - pinctrl-single,pins = < - 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ - 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ - 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ - 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ - >; - }; - - mmc3_pins: pinmux_mmc3_pins { - pinctrl-single,pins = < - OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */ - OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */ - OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */ - OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */ - OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */ - OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */ - >; - }; - - wlan_pins: pinmux_wlan_pins { - pinctrl-single,pins = < - OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */ - >; - }; - - usbhost_pins: pinmux_usbhost_pins { - pinctrl-single,pins = < - 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ - 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ - - 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ - 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ - - 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */ - 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */ - >; - }; - - led_gpio_pins: pinmux_led_gpio_pins { - pinctrl-single,pins = < - 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */ - >; - }; - - uart1_pins: pinmux_uart1_pins { - pinctrl-single,pins = < - 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */ - 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */ - 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */ - 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */ - >; - }; - - uart3_pins: pinmux_uart3_pins { - pinctrl-single,pins = < - 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */ - 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */ - >; - }; - - uart5_pins: pinmux_uart5_pins { - pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */ - 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */ - 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */ - 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */ - >; - }; - - dss_hdmi_pins: pinmux_dss_hdmi_pins { - pinctrl-single,pins = < - 0x0fc (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ - 0x100 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */ - 0x102 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */ - >; - }; - - tpd12s015_pins: pinmux_tpd12s015_pins { - pinctrl-single,pins = < - 0x0fe (PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ - >; - }; }; -&omap5_pmx_wkup { - pinctrl-names = "default"; - pinctrl-0 = < - &usbhost_wkup_pins - >; - - usbhost_wkup_pins: pinmux_usbhost_wkup_pins { - pinctrl-single,pins = < - 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ - >; - }; - - wlcore_irq_pin: pinmux_wlcore_irq_pin { - pinctrl-single,pins = < - OMAP5_IOPAD(0x040, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */ - >; - }; -}; - -&mmc1 { - vmmc-supply = <&ldo9_reg>; - bus-width = <4>; -}; - -&mmc2 { - vmmc-supply = <&vmmcsd_fixed>; - bus-width = <8>; - ti,non-removable; -}; - -&mmc3 { - vmmc-supply = <&vmmcsdio_fixed>; - mmc-pwrseq = <&mmc3_pwrseq>; - bus-width = <4>; - non-removable; - cap-power-off-card; - pinctrl-names = "default"; - pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>; - interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH - &omap5_pmx_core 0x168>; - - #address-cells = <1>; - #size-cells = <0>; - wlcore: wlcore@2 { - compatible = "ti,wl1271"; - reg = <2>; - interrupt-parent = <&gpio1>; - interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */ - ref-clock-frequency = <26000000>; - }; -}; - -&mmc4 { - status = "disabled"; -}; - -&mmc5 { - status = "disabled"; -}; - -&i2c1 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins>; - - clock-frequency = <400000>; - - palmas: palmas@48 { - compatible = "ti,palmas"; - interrupts = ; /* IRQ_SYS_1N */ - reg = <0x48>; - interrupt-controller; - #interrupt-cells = <2>; - ti,system-power-controller; - - extcon_usb3: palmas_usb { - compatible = "ti,palmas-usb-vid"; - ti,enable-vbus-detection; - ti,enable-id-detection; - ti,wakeup; - }; - - clk32kgaudio: palmas_clk32k@1 { - compatible = "ti,palmas-clk32kgaudio"; - #clock-cells = <0>; - }; - - palmas_pmic { - compatible = "ti,palmas-pmic"; - interrupt-parent = <&palmas>; - interrupts = <14 IRQ_TYPE_NONE>; - interrupt-name = "short-irq"; - - ti,ldo6-vibrator; - - regulators { - smps123_reg: smps123 { - /* VDD_OPP_MPU */ - regulator-name = "smps123"; - regulator-min-microvolt = < 600000>; - regulator-max-microvolt = <1500000>; - regulator-always-on; - regulator-boot-on; - }; - - smps45_reg: smps45 { - /* VDD_OPP_MM */ - regulator-name = "smps45"; - regulator-min-microvolt = < 600000>; - regulator-max-microvolt = <1310000>; - regulator-always-on; - regulator-boot-on; - }; - - smps6_reg: smps6 { - /* VDD_DDR3 - over VDD_SMPS6 */ - regulator-name = "smps6"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - regulator-boot-on; - }; - - smps7_reg: smps7 { - /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ - regulator-name = "smps7"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - smps8_reg: smps8 { - /* VDD_OPP_CORE */ - regulator-name = "smps8"; - regulator-min-microvolt = < 600000>; - regulator-max-microvolt = <1310000>; - regulator-always-on; - regulator-boot-on; - }; - - smps9_reg: smps9 { - /* VDDA_2v1_AUD over VDD_2v1 */ - regulator-name = "smps9"; - regulator-min-microvolt = <2100000>; - regulator-max-microvolt = <2100000>; - ti,smps-range = <0x80>; - }; - - smps10_out2_reg: smps10_out2 { - /* VBUS_5V_OTG */ - regulator-name = "smps10_out2"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - }; - - smps10_out1_reg: smps10_out1 { - /* VBUS_5V_OTG */ - regulator-name = "smps10_out1"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - }; - - ldo1_reg: ldo1 { - /* VDDAPHY_CAM: vdda_csiport */ - regulator-name = "ldo1"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1800000>; - }; - - ldo2_reg: ldo2 { - /* VCC_2V8_DISP: Does not go anywhere */ - regulator-name = "ldo2"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - /* Unused */ - status = "disabled"; - }; - - ldo3_reg: ldo3 { - /* VDDAPHY_MDM: vdda_lli */ - regulator-name = "ldo3"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-boot-on; - /* Only if Modem is used */ - status = "disabled"; - }; - - ldo4_reg: ldo4 { - /* VDDAPHY_DISP: vdda_dsiport/hdmi */ - regulator-name = "ldo4"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1800000>; - }; - - ldo5_reg: ldo5 { - /* VDDA_1V8_PHY: usb/sata/hdmi.. */ - regulator-name = "ldo5"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo6_reg: ldo6 { - /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ - regulator-name = "ldo6"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo7_reg: ldo7 { - /* VDD_VPP: vpp1 */ - regulator-name = "ldo7"; - regulator-min-microvolt = <2000000>; - regulator-max-microvolt = <2000000>; - /* Only for efuse reprograming! */ - status = "disabled"; - }; - - ldo8_reg: ldo8 { - /* VDD_3v0: Does not go anywhere */ - regulator-name = "ldo8"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-boot-on; - /* Unused */ - status = "disabled"; - }; - - ldo9_reg: ldo9 { - /* VCC_DV_SDIO: vdds_sdcard */ - regulator-name = "ldo9"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3000000>; - regulator-boot-on; - }; - - ldoln_reg: ldoln { - /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ - regulator-name = "ldoln"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - ldousb_reg: ldousb { - /* VDDA_3V_USB: VDDA_USBHS33 */ - regulator-name = "ldousb"; - regulator-min-microvolt = <3250000>; - regulator-max-microvolt = <3250000>; - regulator-always-on; - regulator-boot-on; - }; - - regen3_reg: regen3 { - /* REGEN3 controls LDO9 supply to card */ - regulator-name = "regen3"; - regulator-always-on; - regulator-boot-on; - }; - }; - }; - - palmas_power_button: palmas_power_button { - compatible = "ti,palmas-pwrbutton"; - interrupt-parent = <&palmas>; - interrupts = <1 IRQ_TYPE_EDGE_FALLING>; - wakeup-source; - }; - }; - - twl6040: twl@4b { - compatible = "ti,twl6040"; - reg = <0x4b>; - - pinctrl-names = "default"; - pinctrl-0 = <&twl6040_pins>; - - interrupts = ; /* IRQ_SYS_2N cascaded to gic */ - ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; /* gpio line 141 */ - - vio-supply = <&smps7_reg>; - v2v1-supply = <&smps9_reg>; - enable-active-high; - - clocks = <&clk32kgaudio>; - clock-names = "clk32k"; - }; +&hdmi { + vdda-supply = <&ldo4_reg>; }; &i2c5 { @@ -601,87 +37,17 @@ }; }; -&mcpdm { - pinctrl-names = "default"; - pinctrl-0 = <&mcpdm_pins>; - status = "okay"; -}; - -&mcbsp1 { - pinctrl-names = "default"; - pinctrl-0 = <&mcbsp1_pins>; - status = "okay"; -}; - -&mcbsp2 { - pinctrl-names = "default"; - pinctrl-0 = <&mcbsp2_pins>; - status = "okay"; -}; - -&usbhshost { - port2-mode = "ehci-hsic"; - port3-mode = "ehci-hsic"; -}; - -&usbhsehci { - phys = <0 &hsusb2_phy &hsusb3_phy>; -}; - -&usb3 { - extcon = <&extcon_usb3>; - vbus-supply = <&smps10_out1_reg>; -}; - -&mcspi1 { - -}; - -&mcspi2 { - pinctrl-names = "default"; - pinctrl-0 = <&mcspi2_pins>; -}; - -&mcspi3 { - pinctrl-names = "default"; - pinctrl-0 = <&mcspi3_pins>; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_pins>; -}; - -&uart3 { - pinctrl-names = "default"; - pinctrl-0 = <&uart3_pins>; - interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, - <&omap5_pmx_core 0x19c>; -}; - -&uart5 { - pinctrl-names = "default"; - pinctrl-0 = <&uart5_pins>; -}; - -&cpu0 { - cpu0-supply = <&smps123_reg>; -}; - -&dss { - status = "ok"; +&omap5_pmx_core { + i2c5_pins: pinmux_i2c5_pins { + pinctrl-single,pins = < + 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */ + 0x188 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */ + >; + }; }; -&hdmi { - status = "ok"; - vdda-supply = <&ldo4_reg>; - - pinctrl-names = "default"; - pinctrl-0 = <&dss_hdmi_pins>; - - port { - hdmi_out: endpoint { - remote-endpoint = <&tpd12s015_in>; - }; - }; +&tpd12s015 { + gpios = <&gpio9 0 GPIO_ACTIVE_HIGH>, /* TCA6424A P01, CT CP HPD */ + <&gpio9 1 GPIO_ACTIVE_HIGH>, /* TCA6424A P00, LS OE */ + <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */ }; -- cgit v1.2.3 From 23c74bf5fe592dff5f6b07c62fa3f909d917f308 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Fri, 16 Oct 2015 12:32:33 -0700 Subject: ARM: dts: Add basic support for isee igepv5 With omap5-board-common.dtsi, we can now easily add support for various omap5 board variants. Let's add minimal support for isee igepv5. So far I've tested that basic things work, such as serial, USB Ethernet, HDMI and WLAN. Note that like omap5-uevm, these boards seem to need to reserve 16MB for a trap section as in commit 03178c66d289 ("ARM: dts: omap5-evm: Update available memory to 2032 MB") and also noted in a u-boot commit at http://marc.info/?l=u-boot&m=134376852603255 and also at http://patchwork.ozlabs.org/patch/159881/. Not sure why this is not needed for omap5-cm-t54.dts, maybe because of different u-boot configuration. Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/omap5-igep0050.dts | 54 ++++++++++++++++++++++++++++++++++++ 2 files changed, 55 insertions(+) create mode 100644 arch/arm/boot/dts/omap5-igep0050.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index e45d771456f3..2c12411fb641 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -471,6 +471,7 @@ dtb-$(CONFIG_SOC_AM43XX) += \ am437x-gp-evm.dtb dtb-$(CONFIG_SOC_OMAP5) += \ omap5-cm-t54.dtb \ + omap5-igep0050.dtb \ omap5-sbc-t54.dtb \ omap5-uevm.dtb dtb-$(CONFIG_SOC_DRA7XX) += \ diff --git a/arch/arm/boot/dts/omap5-igep0050.dts b/arch/arm/boot/dts/omap5-igep0050.dts new file mode 100644 index 000000000000..46ecb1dd3b5c --- /dev/null +++ b/arch/arm/boot/dts/omap5-igep0050.dts @@ -0,0 +1,54 @@ +/* + * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "omap5-board-common.dtsi" + +/ { + model = "IGEPv5"; + compatible = "isee,omap5-igep0050", "ti,omap5"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x7f000000>; /* 2032 MB */ + }; +}; + +&hdmi { + vdda-supply = <&ldo7_reg>; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + + tca6416: tca6416@21 { + compatible = "ti,tca6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&omap5_pmx_core { + i2c4_pins: pinmux_i2c4_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0) /* i2c4_scl */ + OMAP5_IOPAD(0x0fa, PIN_INPUT | MUX_MODE0) /* i2c4_sda */ + >; + }; +}; + +&tpd12s015 { + gpios = <&tca6416 11 0>, /* TCA6416 P01, CT_CP_HDP */ + <&tca6416 12 0>, /* TCA6416 P00, LS_OE*/ + <&gpio7 1 0>, /* 193, HPD */ + <&gpio7 2 0>, /* 194, SCL */ + <&gpio7 3 0>; /* 195, SDA */ +}; + -- cgit v1.2.3 From 36958598b7acf690b514141122234b1c3b8e4282 Mon Sep 17 00:00:00 2001 From: Mugunthan V N Date: Mon, 21 Sep 2015 20:23:51 +0530 Subject: ARM: dts: dra72-evm: remove cpsw gpio hogging and add mode-gpios With the current implementation of GPIO hogging and with gpio-pcf857x is built as module, ethernet doesn't work on boot and doesn't throw any error/warning to user. Ethernet becomes operational when inserting gpio-pcf857x module, even this time there is no error/warning logs to user that ethernet is operational. When using with NFS rootfs and gpio-pcf857x as module, board doesn't boot as it doesn't get any ip address and doesn't throw any error/warning. To over come this, now cpsw driver tries to get mode-gpios. When gpio-pcf857x is built as module it will throw error, so that user can decide either to built in gpio-pcf857x to continue with nfs boot or choose alternate rootfs filesystem like sd/ramdisk. When using mmc/ramdisk as root fs, cpsw will probe defer and re-probes again when gpio-pcf857x module is inserted and ethernet becomes operational. Signed-off-by: Mugunthan V N Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra72-evm.dts | 7 +------ 1 file changed, 1 insertion(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index 27e414295acc..d6104d5f0c01 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -429,12 +429,6 @@ interrupts = <11 IRQ_TYPE_EDGE_FALLING>; interrupt-controller; #interrupt-cells = <2>; - - cpsw_sel_s0 { - gpio-hog; - gpios = <4 GPIO_ACTIVE_HIGH>; - output-low; - }; }; tlv320aic3106: tlv320aic3106@19 { @@ -689,6 +683,7 @@ pinctrl-0 = <&cpsw_default>; pinctrl-1 = <&cpsw_sleep>; slaves = <1>; + mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>; }; &cpsw_emac0 { -- cgit v1.2.3 From 56a31e549e007ad7ca623d99294af0eca8517bf8 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Wed, 14 Oct 2015 12:00:30 +0200 Subject: ARM: dts: Update Javier Martinez Canillas's email I see that people are still sending emails to my old address (that no longer exists) since is the one mentioned in the IGEP DTS. Replace it with my current email address to avoid this. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep.dtsi | 2 +- arch/arm/boot/dts/omap3-igep0020-common.dtsi | 2 +- arch/arm/boot/dts/omap3-igep0020-rev-f.dts | 2 +- arch/arm/boot/dts/omap3-igep0020.dts | 2 +- arch/arm/boot/dts/omap3-igep0030-common.dtsi | 2 +- arch/arm/boot/dts/omap3-igep0030-rev-g.dts | 2 +- arch/arm/boot/dts/omap3-igep0030.dts | 2 +- 7 files changed, 7 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index 09a438ebfbbe..3caf062f882c 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -1,7 +1,7 @@ /* * Common device tree for IGEP boards based on AM/DM37x * - * Copyright (C) 2012 Javier Martinez Canillas + * Copyright (C) 2012 Javier Martinez Canillas * Copyright (C) 2012 Enric Balletbo i Serra * * This program is free software; you can redistribute it and/or modify diff --git a/arch/arm/boot/dts/omap3-igep0020-common.dtsi b/arch/arm/boot/dts/omap3-igep0020-common.dtsi index 5ad688c57a00..441999817285 100644 --- a/arch/arm/boot/dts/omap3-igep0020-common.dtsi +++ b/arch/arm/boot/dts/omap3-igep0020-common.dtsi @@ -1,7 +1,7 @@ /* * Common Device Tree Source for IGEPv2 * - * Copyright (C) 2014 Javier Martinez Canillas + * Copyright (C) 2014 Javier Martinez Canillas * Copyright (C) 2014 Enric Balletbo i Serra * * This program is free software; you can redistribute it and/or modify diff --git a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts b/arch/arm/boot/dts/omap3-igep0020-rev-f.dts index 72f7cdc091fb..321c2b7a4e9f 100644 --- a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts +++ b/arch/arm/boot/dts/omap3-igep0020-rev-f.dts @@ -1,7 +1,7 @@ /* * Device Tree Source for IGEPv2 Rev. F (TI OMAP AM/DM37x) * - * Copyright (C) 2012 Javier Martinez Canillas + * Copyright (C) 2012 Javier Martinez Canillas * Copyright (C) 2012 Enric Balletbo i Serra * * This program is free software; you can redistribute it and/or modify diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index 5683b8bf3475..3835e1569c29 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -1,7 +1,7 @@ /* * Device Tree Source for IGEPv2 Rev. C (TI OMAP AM/DM37x) * - * Copyright (C) 2012 Javier Martinez Canillas + * Copyright (C) 2012 Javier Martinez Canillas * Copyright (C) 2012 Enric Balletbo i Serra * * This program is free software; you can redistribute it and/or modify diff --git a/arch/arm/boot/dts/omap3-igep0030-common.dtsi b/arch/arm/boot/dts/omap3-igep0030-common.dtsi index 0cb1527c39d4..640f06603966 100644 --- a/arch/arm/boot/dts/omap3-igep0030-common.dtsi +++ b/arch/arm/boot/dts/omap3-igep0030-common.dtsi @@ -1,7 +1,7 @@ /* * Common Device Tree Source for IGEP COM MODULE * - * Copyright (C) 2014 Javier Martinez Canillas + * Copyright (C) 2014 Javier Martinez Canillas * Copyright (C) 2014 Enric Balletbo i Serra * * This program is free software; you can redistribute it and/or modify diff --git a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts b/arch/arm/boot/dts/omap3-igep0030-rev-g.dts index b899e341874a..76dc08868bfb 100644 --- a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts +++ b/arch/arm/boot/dts/omap3-igep0030-rev-g.dts @@ -1,7 +1,7 @@ /* * Device Tree Source for IGEP COM MODULE Rev. G (TI OMAP AM/DM37x) * - * Copyright (C) 2014 Javier Martinez Canillas + * Copyright (C) 2014 Javier Martinez Canillas * Copyright (C) 2014 Enric Balletbo i Serra * * This program is free software; you can redistribute it and/or modify diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts index 8150f47ccdf5..468608dab30a 100644 --- a/arch/arm/boot/dts/omap3-igep0030.dts +++ b/arch/arm/boot/dts/omap3-igep0030.dts @@ -1,7 +1,7 @@ /* * Device Tree Source for IGEP COM MODULE Rev. E (TI OMAP AM/DM37x) * - * Copyright (C) 2012 Javier Martinez Canillas + * Copyright (C) 2012 Javier Martinez Canillas * Copyright (C) 2012 Enric Balletbo i Serra * * This program is free software; you can redistribute it and/or modify -- cgit v1.2.3 From f513d22c9cb09ff95a0c2d26e18940fbda50d6db Mon Sep 17 00:00:00 2001 From: Vignesh R Date: Wed, 14 Oct 2015 19:24:25 +0530 Subject: ARM: dts: am437x-gp-evm: Add wakeup interrupt source for pixcir_i2c_ts On am437x-gp-evm, pixcir_i2c_ts can wakeup the system from low power state via pinctrl and IO daisy chain using generic wakeirq framework. With commit 3fffd1283927 ("i2c: allow specifying separate wakeup interrupt in device tree") i2c core allows optional wakeirq to be specified via device tree. Add wakeup irq entry to enable pixcir_i2c_ts to wake the system from low power state. Signed-off-by: Vignesh R Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-gp-evm.dts | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts index b259d7c29bcd..d2450ab0a380 100644 --- a/arch/arm/boot/dts/am437x-gp-evm.dts +++ b/arch/arm/boot/dts/am437x-gp-evm.dts @@ -595,8 +595,17 @@ attb-gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; + /* + * 0x264 represents the offset of padconf register of + * gpio3_22 from am43xx_pinmux base. + */ + interrupts-extended = <&gpio3 22 IRQ_TYPE_NONE>, + <&am43xx_pinmux 0x264>; + interrupt-names = "tsc", "wakeup"; + touchscreen-size-x = <1024>; touchscreen-size-y = <600>; + wakeup-source; }; ov2659@30 { -- cgit v1.2.3 From fd20719443e420d09e2813d7c7b582e229f3cbdc Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Mon, 19 Oct 2015 17:34:19 +0200 Subject: ARM: dts: omap3-igep0020: Use IOPAD pinmux macro Use the OMAP3 pinmux IOPAD macro to define the physical address instead of the offset from the padconf address. It makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep0020-common.dtsi | 58 ++++++++++++++-------------- 1 file changed, 29 insertions(+), 29 deletions(-) diff --git a/arch/arm/boot/dts/omap3-igep0020-common.dtsi b/arch/arm/boot/dts/omap3-igep0020-common.dtsi index 441999817285..d90f12c39307 100644 --- a/arch/arm/boot/dts/omap3-igep0020-common.dtsi +++ b/arch/arm/boot/dts/omap3-igep0020-common.dtsi @@ -111,40 +111,40 @@ tfp410_pins: pinmux_tfp410_pins { pinctrl-single,pins = < - 0x196 (PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */ + OMAP3_CORE1_IOPAD(0x21c6, PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */ >; }; dss_dpi_pins: pinmux_dss_dpi_pins { pinctrl-single,pins = < - 0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ - 0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ - 0x0a8 (PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ - 0x0aa (PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ - 0x0ac (PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ - 0x0ae (PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ - 0x0b0 (PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ - 0x0b2 (PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ - 0x0b4 (PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ - 0x0b6 (PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ - 0x0b8 (PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ - 0x0ba (PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ - 0x0bc (PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ - 0x0be (PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ - 0x0c0 (PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ - 0x0c2 (PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ - 0x0c4 (PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ - 0x0c6 (PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ - 0x0c8 (PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ - 0x0ca (PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ - 0x0cc (PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ - 0x0ce (PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ - 0x0d0 (PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ - 0x0d2 (PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ - 0x0d4 (PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ - 0x0d6 (PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ - 0x0d8 (PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ - 0x0da (PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ + OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ + OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ + OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ >; }; -- cgit v1.2.3 From 8a3ecb217f11884890d81c9440087c0765606daf Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Mon, 19 Oct 2015 17:34:20 +0200 Subject: ARM: dts: am335x-igep0033: Use IOPAD pinmux macro Use the AM33xx pinmux IOPAD macro to define the physical address instead of the offset from the padconf address. It makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-igep0033.dtsi | 40 +++++++++++++++++----------------- 1 file changed, 20 insertions(+), 20 deletions(-) diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi index c0e1135256cc..54f113546ecc 100644 --- a/arch/arm/boot/dts/am335x-igep0033.dtsi +++ b/arch/arm/boot/dts/am335x-igep0033.dtsi @@ -56,41 +56,41 @@ &am33xx_pinmux { i2c0_pins: pinmux_i2c0_pins { pinctrl-single,pins = < - 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ - 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; nandflash_pins: pinmux_nandflash_pins { pinctrl-single,pins = < - 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ - 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ - 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ - 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ - 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ - 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ - 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ - 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ - 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ - 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ - 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ - 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ - 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ - 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ - 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + AM33XX_IOPAD(0x874, PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */ + AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ >; }; uart0_pins: pinmux_uart0_pins { pinctrl-single,pins = < - 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ - 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ >; }; leds_pins: pinmux_leds_pins { pinctrl-single,pins = < - 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ + AM33XX_IOPAD(0x85c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */ >; }; }; -- cgit v1.2.3 From e9a267702d32fc8e71abe5f172d2924bad86e52f Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Mon, 19 Oct 2015 17:34:21 +0200 Subject: ARM: dts: am335x-base0033: Use IOPAD pinmux macro Use the AM33XX pinmux IOPAD macro to define the physical address instead of the offset from the padconf address. It makes the DTS easier to read since matches the addresses listed in the Technical Reference Manual. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-base0033.dts | 48 +++++++++++++++++------------------ 1 file changed, 24 insertions(+), 24 deletions(-) diff --git a/arch/arm/boot/dts/am335x-base0033.dts b/arch/arm/boot/dts/am335x-base0033.dts index 72a9b3fc4251..58a05f7d0b7c 100644 --- a/arch/arm/boot/dts/am335x-base0033.dts +++ b/arch/arm/boot/dts/am335x-base0033.dts @@ -46,39 +46,39 @@ &am33xx_pinmux { nxp_hdmi_pins: pinmux_nxp_hdmi_pins { pinctrl-single,pins = < - 0x1b0 (PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ - 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0 */ - 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1 */ - 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2 */ - 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3 */ - 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4 */ - 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5 */ - 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6 */ - 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7 */ - 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8 */ - 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9 */ - 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10 */ - 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11 */ - 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12 */ - 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13 */ - 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14 */ - 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15 */ - 0xe0 (PIN_OUTPUT | MUX_MODE0) /* lcd_vsync */ - 0xe4 (PIN_OUTPUT | MUX_MODE0) /* lcd_hsync */ - 0xe8 (PIN_OUTPUT | MUX_MODE0) /* lcd_pclk */ - 0xec (PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en */ + AM33XX_IOPAD(0x9b0, PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0 */ + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1 */ + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2 */ + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3 */ + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4 */ + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5 */ + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6 */ + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7 */ + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8 */ + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9 */ + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10 */ + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11 */ + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12 */ + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13 */ + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14 */ + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15 */ + AM33XX_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE0) /* lcd_vsync */ + AM33XX_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE0) /* lcd_hsync */ + AM33XX_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE0) /* lcd_pclk */ + AM33XX_IOPAD(0x8ec, PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en */ >; }; nxp_hdmi_off_pins: pinmux_nxp_hdmi_off_pins { pinctrl-single,pins = < - 0x1b0 (PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ + AM33XX_IOPAD(0x9b0, PIN_OUTPUT | MUX_MODE3) /* xdma_event_intr0.clkout1 */ >; }; leds_base_pins: pinmux_leds_base_pins { pinctrl-single,pins = < - 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ - 0x88 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn3.gpio2_0 */ + AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */ + AM33XX_IOPAD(0x888, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_csn3.gpio2_0 */ >; }; }; -- cgit v1.2.3