From e4d0db60e8d25cc62b9b7e32c18e7f6acc136055 Mon Sep 17 00:00:00 2001 From: John Hsu Date: Tue, 7 Nov 2017 15:23:17 +0800 Subject: ASoC: nau8540: reset state machine for channel phase sync The four channel ADCs in NAU85L40 have difference control registers, it is hard to synchronous these four channels without correct sequence. The phase difference will not be a constant and not to conjecture easily. It may be 2.55 degree, or more ,or less. Intended to prevent phase difference of channels, the solution as follows: (1)Channel_Sync need to be enabled. (2)Do soft reset without affecting register when recording done. Signed-off-by: John Hsu Signed-off-by: Mark Brown --- sound/soc/codecs/nau8540.c | 23 ++++++++++++++++++++--- sound/soc/codecs/nau8540.h | 1 + 2 files changed, 21 insertions(+), 3 deletions(-) diff --git a/sound/soc/codecs/nau8540.c b/sound/soc/codecs/nau8540.c index f9c9933acffb..c10cbffa6314 100644 --- a/sound/soc/codecs/nau8540.c +++ b/sound/soc/codecs/nau8540.c @@ -233,6 +233,19 @@ static SOC_ENUM_SINGLE_DECL( static const struct snd_kcontrol_new digital_ch1_mux = SOC_DAPM_ENUM("Digital CH1 Select", digital_ch1_enum); +static int aiftx_power_control(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *k, int event) +{ + struct snd_soc_codec *codec = snd_soc_dapm_to_codec(w->dapm); + struct nau8540 *nau8540 = snd_soc_codec_get_drvdata(codec); + + if (SND_SOC_DAPM_EVENT_OFF(event)) { + regmap_write(nau8540->regmap, NAU8540_REG_RST, 0x0001); + regmap_write(nau8540->regmap, NAU8540_REG_RST, 0x0000); + } + return 0; +} + static const struct snd_soc_dapm_widget nau8540_dapm_widgets[] = { SND_SOC_DAPM_SUPPLY("MICBIAS2", NAU8540_REG_MIC_BIAS, 11, 0, NULL, 0), SND_SOC_DAPM_SUPPLY("MICBIAS1", NAU8540_REG_MIC_BIAS, 10, 0, NULL, 0), @@ -270,7 +283,8 @@ static const struct snd_soc_dapm_widget nau8540_dapm_widgets[] = { SND_SOC_DAPM_MUX("Digital CH1 Mux", SND_SOC_NOPM, 0, 0, &digital_ch1_mux), - SND_SOC_DAPM_AIF_OUT("AIFTX", "Capture", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT_E("AIFTX", "Capture", 0, SND_SOC_NOPM, 0, 0, + aiftx_power_control, SND_SOC_DAPM_POST_PMD), }; static const struct snd_soc_dapm_route nau8540_dapm_routes[] = { @@ -710,9 +724,12 @@ static void nau8540_init_regs(struct nau8540 *nau8540) regmap_update_bits(regmap, NAU8540_REG_CLOCK_CTRL, NAU8540_CLK_ADC_EN | NAU8540_CLK_I2S_EN, NAU8540_CLK_ADC_EN | NAU8540_CLK_I2S_EN); - /* ADC OSR selection, CLK_ADC = Fs * OSR */ + /* ADC OSR selection, CLK_ADC = Fs * OSR; + * Channel time alignment enable. + */ regmap_update_bits(regmap, NAU8540_REG_ADC_SAMPLE_RATE, - NAU8540_ADC_OSR_MASK, NAU8540_ADC_OSR_64); + NAU8540_CH_SYNC | NAU8540_ADC_OSR_MASK, + NAU8540_CH_SYNC | NAU8540_ADC_OSR_64); } static int __maybe_unused nau8540_suspend(struct snd_soc_codec *codec) diff --git a/sound/soc/codecs/nau8540.h b/sound/soc/codecs/nau8540.h index 5db5b224944d..14339f9bb01a 100644 --- a/sound/soc/codecs/nau8540.h +++ b/sound/soc/codecs/nau8540.h @@ -165,6 +165,7 @@ #define NAU8540_TDM_TX_MASK 0xf /* ADC_SAMPLE_RATE (0x3A) */ +#define NAU8540_CH_SYNC (0x1 << 14) #define NAU8540_ADC_OSR_MASK 0x3 #define NAU8540_ADC_OSR_256 0x3 #define NAU8540_ADC_OSR_128 0x2 -- cgit v1.2.3 From 14323ff8c21825e20810e893312f9321f9e4e72c Mon Sep 17 00:00:00 2001 From: John Hsu Date: Tue, 7 Nov 2017 15:23:18 +0800 Subject: ASoC: nau8540: PGA short to ground Change channel PGA input mode selection for better recording quality. The patch shorts the inputs to ground with 12kOhm differentially terminated. Signed-off-by: John Hsu Signed-off-by: Mark Brown --- sound/soc/codecs/nau8540.c | 7 +++++++ sound/soc/codecs/nau8540.h | 12 ++++++++++++ 2 files changed, 19 insertions(+) diff --git a/sound/soc/codecs/nau8540.c b/sound/soc/codecs/nau8540.c index c10cbffa6314..8246486a588d 100644 --- a/sound/soc/codecs/nau8540.c +++ b/sound/soc/codecs/nau8540.c @@ -730,6 +730,13 @@ static void nau8540_init_regs(struct nau8540 *nau8540) regmap_update_bits(regmap, NAU8540_REG_ADC_SAMPLE_RATE, NAU8540_CH_SYNC | NAU8540_ADC_OSR_MASK, NAU8540_CH_SYNC | NAU8540_ADC_OSR_64); + /* PGA input mode selection */ + regmap_update_bits(regmap, NAU8540_REG_FEPGA1, + NAU8540_FEPGA1_MODCH2_SHT | NAU8540_FEPGA1_MODCH1_SHT, + NAU8540_FEPGA1_MODCH2_SHT | NAU8540_FEPGA1_MODCH1_SHT); + regmap_update_bits(regmap, NAU8540_REG_FEPGA2, + NAU8540_FEPGA2_MODCH4_SHT | NAU8540_FEPGA2_MODCH3_SHT, + NAU8540_FEPGA2_MODCH4_SHT | NAU8540_FEPGA2_MODCH3_SHT); } static int __maybe_unused nau8540_suspend(struct snd_soc_codec *codec) diff --git a/sound/soc/codecs/nau8540.h b/sound/soc/codecs/nau8540.h index 14339f9bb01a..7083d4821ce4 100644 --- a/sound/soc/codecs/nau8540.h +++ b/sound/soc/codecs/nau8540.h @@ -184,6 +184,18 @@ #define NAU8540_PRECHARGE_DIS (0x1 << 13) #define NAU8540_GLOBAL_BIAS_EN (0x1 << 12) +/* FEPGA1 (0x69) */ +#define NAU8540_FEPGA1_MODCH2_SHT_SFT 7 +#define NAU8540_FEPGA1_MODCH2_SHT (0x1 << NAU8540_FEPGA1_MODCH2_SHT_SFT) +#define NAU8540_FEPGA1_MODCH1_SHT_SFT 3 +#define NAU8540_FEPGA1_MODCH1_SHT (0x1 << NAU8540_FEPGA1_MODCH1_SHT_SFT) + +/* FEPGA2 (0x6A) */ +#define NAU8540_FEPGA2_MODCH4_SHT_SFT 7 +#define NAU8540_FEPGA2_MODCH4_SHT (0x1 << NAU8540_FEPGA2_MODCH4_SHT_SFT) +#define NAU8540_FEPGA2_MODCH3_SHT_SFT 3 +#define NAU8540_FEPGA2_MODCH3_SHT (0x1 << NAU8540_FEPGA2_MODCH3_SHT_SFT) + /* System Clock Source */ enum { -- cgit v1.2.3 From 6573c0510be611fb886d005b7b2321658dc5df87 Mon Sep 17 00:00:00 2001 From: John Hsu Date: Tue, 7 Nov 2017 15:23:19 +0800 Subject: ASoC: nau8540: fix the record pop noise When the record starts, the driver turns on MICBIAS and the voltage is pulled up for an instant. If the receiver starts to capture the signal between the instant, there is an pop noise in the stream beginning. To avoid the pop noise, the driver makes a delay in the sequence. After MICBIAS powered up, the driver waits 300 ms for the voltage going down. Then turns on the ADC output, and sends signal to receiver. The pop noise can be erased. Signed-off-by: John Hsu Signed-off-by: Mark Brown --- sound/soc/codecs/nau8540.c | 47 ++++++++++++++++++++++++++++++++++++++-------- sound/soc/codecs/nau8540.h | 2 ++ 2 files changed, 41 insertions(+), 8 deletions(-) diff --git a/sound/soc/codecs/nau8540.c b/sound/soc/codecs/nau8540.c index 8246486a588d..9565f9a181a9 100644 --- a/sound/soc/codecs/nau8540.c +++ b/sound/soc/codecs/nau8540.c @@ -233,6 +233,28 @@ static SOC_ENUM_SINGLE_DECL( static const struct snd_kcontrol_new digital_ch1_mux = SOC_DAPM_ENUM("Digital CH1 Select", digital_ch1_enum); +static int adc_power_control(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *k, int event) +{ + struct snd_soc_codec *codec = snd_soc_dapm_to_codec(w->dapm); + struct nau8540 *nau8540 = snd_soc_codec_get_drvdata(codec); + + if (SND_SOC_DAPM_EVENT_ON(event)) { + msleep(300); + /* DO12 and DO34 pad output enable */ + regmap_update_bits(nau8540->regmap, NAU8540_REG_PCM_CTRL1, + NAU8540_I2S_DO12_TRI, 0); + regmap_update_bits(nau8540->regmap, NAU8540_REG_PCM_CTRL2, + NAU8540_I2S_DO34_TRI, 0); + } else if (SND_SOC_DAPM_EVENT_OFF(event)) { + regmap_update_bits(nau8540->regmap, NAU8540_REG_PCM_CTRL1, + NAU8540_I2S_DO12_TRI, NAU8540_I2S_DO12_TRI); + regmap_update_bits(nau8540->regmap, NAU8540_REG_PCM_CTRL2, + NAU8540_I2S_DO34_TRI, NAU8540_I2S_DO34_TRI); + } + return 0; +} + static int aiftx_power_control(struct snd_soc_dapm_widget *w, struct snd_kcontrol *k, int event) { @@ -260,14 +282,18 @@ static const struct snd_soc_dapm_widget nau8540_dapm_widgets[] = { SND_SOC_DAPM_PGA("Frontend PGA3", NAU8540_REG_PWR, 14, 0, NULL, 0), SND_SOC_DAPM_PGA("Frontend PGA4", NAU8540_REG_PWR, 15, 0, NULL, 0), - SND_SOC_DAPM_ADC("ADC1", NULL, - NAU8540_REG_POWER_MANAGEMENT, 0, 0), - SND_SOC_DAPM_ADC("ADC2", NULL, - NAU8540_REG_POWER_MANAGEMENT, 1, 0), - SND_SOC_DAPM_ADC("ADC3", NULL, - NAU8540_REG_POWER_MANAGEMENT, 2, 0), - SND_SOC_DAPM_ADC("ADC4", NULL, - NAU8540_REG_POWER_MANAGEMENT, 3, 0), + SND_SOC_DAPM_ADC_E("ADC1", NULL, + NAU8540_REG_POWER_MANAGEMENT, 0, 0, adc_power_control, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_ADC_E("ADC2", NULL, + NAU8540_REG_POWER_MANAGEMENT, 1, 0, adc_power_control, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_ADC_E("ADC3", NULL, + NAU8540_REG_POWER_MANAGEMENT, 2, 0, adc_power_control, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_ADC_E("ADC4", NULL, + NAU8540_REG_POWER_MANAGEMENT, 3, 0, adc_power_control, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), SND_SOC_DAPM_PGA("ADC CH1", NAU8540_REG_ANALOG_PWR, 0, 0, NULL, 0), SND_SOC_DAPM_PGA("ADC CH2", NAU8540_REG_ANALOG_PWR, 1, 0, NULL, 0), @@ -737,6 +763,11 @@ static void nau8540_init_regs(struct nau8540 *nau8540) regmap_update_bits(regmap, NAU8540_REG_FEPGA2, NAU8540_FEPGA2_MODCH4_SHT | NAU8540_FEPGA2_MODCH3_SHT, NAU8540_FEPGA2_MODCH4_SHT | NAU8540_FEPGA2_MODCH3_SHT); + /* DO12 and DO34 pad output disable */ + regmap_update_bits(regmap, NAU8540_REG_PCM_CTRL1, + NAU8540_I2S_DO12_TRI, NAU8540_I2S_DO12_TRI); + regmap_update_bits(regmap, NAU8540_REG_PCM_CTRL2, + NAU8540_I2S_DO34_TRI, NAU8540_I2S_DO34_TRI); } static int __maybe_unused nau8540_suspend(struct snd_soc_codec *codec) diff --git a/sound/soc/codecs/nau8540.h b/sound/soc/codecs/nau8540.h index 7083d4821ce4..dceb04b23c19 100644 --- a/sound/soc/codecs/nau8540.h +++ b/sound/soc/codecs/nau8540.h @@ -146,6 +146,7 @@ #define NAU8540_I2S_DF_PCM_AB 0x3 /* PCM_CTRL1 (0x11) */ +#define NAU8540_I2S_DO12_TRI (0x1 << 15) #define NAU8540_I2S_LRC_DIV_SFT 12 #define NAU8540_I2S_LRC_DIV_MASK (0x3 << NAU8540_I2S_LRC_DIV_SFT) #define NAU8540_I2S_DO12_OE (0x1 << 4) @@ -156,6 +157,7 @@ #define NAU8540_I2S_BLK_DIV_MASK 0x7 /* PCM_CTRL1 (0x12) */ +#define NAU8540_I2S_DO34_TRI (0x1 << 15) #define NAU8540_I2S_DO34_OE (0x1 << 11) #define NAU8540_I2S_TSLOT_L_MASK 0x3ff -- cgit v1.2.3 From cf6b68d192138d67b49002b499eb507af0c8c56d Mon Sep 17 00:00:00 2001 From: John Hsu Date: Tue, 7 Nov 2017 17:06:32 +0800 Subject: ASoC: nau8824: move key irq after jd done It is possible to get the fake key press interruption when the codec do jack detection. We think it's proper to move the key interruption configuration after jack detection done. Signed-off-by: John Hsu Signed-off-by: Mark Brown --- sound/soc/codecs/nau8824.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-) diff --git a/sound/soc/codecs/nau8824.c b/sound/soc/codecs/nau8824.c index 0240759f951c..b7b63ac037a7 100644 --- a/sound/soc/codecs/nau8824.c +++ b/sound/soc/codecs/nau8824.c @@ -843,6 +843,11 @@ static void nau8824_jdet_work(struct work_struct *work) event_mask |= SND_JACK_HEADSET; snd_soc_jack_report(nau8824->jack, event, event_mask); + /* Enable short key press and release interruption. */ + regmap_update_bits(regmap, NAU8824_REG_INTERRUPT_SETTING, + NAU8824_IRQ_KEY_RELEASE_DIS | + NAU8824_IRQ_KEY_SHORT_PRESS_DIS, 0); + nau8824_sema_release(nau8824); } @@ -850,13 +855,12 @@ static void nau8824_setup_auto_irq(struct nau8824 *nau8824) { struct regmap *regmap = nau8824->regmap; - /* Enable jack ejection, short key press and release interruption. */ + /* Enable jack ejection interruption. */ regmap_update_bits(regmap, NAU8824_REG_INTERRUPT_SETTING_1, NAU8824_IRQ_INSERT_EN | NAU8824_IRQ_EJECT_EN, NAU8824_IRQ_EJECT_EN); regmap_update_bits(regmap, NAU8824_REG_INTERRUPT_SETTING, - NAU8824_IRQ_EJECT_DIS | NAU8824_IRQ_KEY_RELEASE_DIS | - NAU8824_IRQ_KEY_SHORT_PRESS_DIS, 0); + NAU8824_IRQ_EJECT_DIS, 0); /* Enable internal VCO needed for interruptions */ nau8824_config_sysclk(nau8824, NAU8824_CLK_INTERNAL, 0); regmap_update_bits(regmap, NAU8824_REG_ENA_CTRL, -- cgit v1.2.3 From a2eb62edbd01064cee0c4c00854a25f04237605b Mon Sep 17 00:00:00 2001 From: John Hsu Date: Tue, 7 Nov 2017 17:06:33 +0800 Subject: ASoC: nau8824: condition for clock disable There are headphone and speaker outputs in NAU88L24. During the playback, the codec should not change the clock status when switching these outputs. Signed-off-by: John Hsu Signed-off-by: Mark Brown --- sound/soc/codecs/nau8824.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/sound/soc/codecs/nau8824.c b/sound/soc/codecs/nau8824.c index b7b63ac037a7..8a9a9939827e 100644 --- a/sound/soc/codecs/nau8824.c +++ b/sound/soc/codecs/nau8824.c @@ -811,7 +811,8 @@ static void nau8824_eject_jack(struct nau8824 *nau8824) NAU8824_JD_SLEEP_MODE, NAU8824_JD_SLEEP_MODE); /* Close clock for jack type detection at manual mode */ - nau8824_config_sysclk(nau8824, NAU8824_CLK_DIS, 0); + if (dapm->bias_level < SND_SOC_BIAS_PREPARE) + nau8824_config_sysclk(nau8824, NAU8824_CLK_DIS, 0); } static void nau8824_jdet_work(struct work_struct *work) @@ -862,7 +863,8 @@ static void nau8824_setup_auto_irq(struct nau8824 *nau8824) regmap_update_bits(regmap, NAU8824_REG_INTERRUPT_SETTING, NAU8824_IRQ_EJECT_DIS, 0); /* Enable internal VCO needed for interruptions */ - nau8824_config_sysclk(nau8824, NAU8824_CLK_INTERNAL, 0); + if (nau8824->dapm->bias_level < SND_SOC_BIAS_PREPARE) + nau8824_config_sysclk(nau8824, NAU8824_CLK_INTERNAL, 0); regmap_update_bits(regmap, NAU8824_REG_ENA_CTRL, NAU8824_JD_SLEEP_MODE, 0); } -- cgit v1.2.3 From fe83b1b7d7d0ff11210f84f25b8e1ba1afbac76f Mon Sep 17 00:00:00 2001 From: John Hsu Date: Mon, 13 Nov 2017 10:16:17 +0800 Subject: ASoC: nau8540: improve FLL performance Add these parameters to improve the FLL performance. The comments show as follows: (1)ICTRL_LATCH: FLL DSP speed capability control When FLL running at high frequency with long decimal number, DSP needs to operate at high speed. FLL DSP can optimize between performance and power consumption by ICTRL_LATCH.(111 has highest power consumption.) The default setting can be used to reduce power. (2)CUTOFF500: loop filter cutoff frequency at 500Khz It will give the best FLL performance but highest power consumption to enable the cutoff frequency. FLL Loop Filter enable to reduce FLL output noise, especially,(DCO frequency)/(FLL input reference frequency) is not a integer. (3)GAIN_ERR: FLL gain error correction threshold setting The threshold is comparison between DCO and target frequency. The value 1111 has the most sensitive threshold, that is, 1111 can have the most accurate DCO to target frequency. However, the gain error setting conditionally and inversely depends on FLL input reference clock rate. Higher FLL reference input frequency can only set lower gain error, such as 0000 for input reference from MCLK=12.288Mhz. On the other side, if FLL reference input is from Frame Sync, 48KHz, higher error gain can apply such as 1111. Signed-off-by: John Hsu Signed-off-by: Mark Brown --- sound/soc/codecs/nau8540.c | 21 ++++++++++++++------- sound/soc/codecs/nau8540.h | 5 +++++ 2 files changed, 19 insertions(+), 7 deletions(-) diff --git a/sound/soc/codecs/nau8540.c b/sound/soc/codecs/nau8540.c index 9565f9a181a9..b08fb7e243c3 100644 --- a/sound/soc/codecs/nau8540.c +++ b/sound/soc/codecs/nau8540.c @@ -615,7 +615,8 @@ static void nau8540_fll_apply(struct regmap *regmap, NAU8540_CLK_SRC_MASK | NAU8540_CLK_MCLK_SRC_MASK, NAU8540_CLK_SRC_MCLK | fll_param->mclk_src); regmap_update_bits(regmap, NAU8540_REG_FLL1, - NAU8540_FLL_RATIO_MASK, fll_param->ratio); + NAU8540_FLL_RATIO_MASK | NAU8540_ICTRL_LATCH_MASK, + fll_param->ratio | (0x6 << NAU8540_ICTRL_LATCH_SFT)); /* FLL 16-bit fractional input */ regmap_write(regmap, NAU8540_REG_FLL2, fll_param->fll_frac); /* FLL 10-bit integer input */ @@ -636,13 +637,14 @@ static void nau8540_fll_apply(struct regmap *regmap, NAU8540_FLL_PDB_DAC_EN | NAU8540_FLL_LOOP_FTR_EN | NAU8540_FLL_FTR_SW_FILTER); regmap_update_bits(regmap, NAU8540_REG_FLL6, - NAU8540_SDM_EN, NAU8540_SDM_EN); + NAU8540_SDM_EN | NAU8540_CUTOFF500, + NAU8540_SDM_EN | NAU8540_CUTOFF500); } else { regmap_update_bits(regmap, NAU8540_REG_FLL5, NAU8540_FLL_PDB_DAC_EN | NAU8540_FLL_LOOP_FTR_EN | NAU8540_FLL_FTR_SW_MASK, NAU8540_FLL_FTR_SW_ACCU); - regmap_update_bits(regmap, - NAU8540_REG_FLL6, NAU8540_SDM_EN, 0); + regmap_update_bits(regmap, NAU8540_REG_FLL6, + NAU8540_SDM_EN | NAU8540_CUTOFF500, 0); } } @@ -657,17 +659,22 @@ static int nau8540_set_pll(struct snd_soc_codec *codec, int pll_id, int source, switch (pll_id) { case NAU8540_CLK_FLL_MCLK: regmap_update_bits(nau8540->regmap, NAU8540_REG_FLL3, - NAU8540_FLL_CLK_SRC_MASK, NAU8540_FLL_CLK_SRC_MCLK); + NAU8540_FLL_CLK_SRC_MASK | NAU8540_GAIN_ERR_MASK, + NAU8540_FLL_CLK_SRC_MCLK | 0); break; case NAU8540_CLK_FLL_BLK: regmap_update_bits(nau8540->regmap, NAU8540_REG_FLL3, - NAU8540_FLL_CLK_SRC_MASK, NAU8540_FLL_CLK_SRC_BLK); + NAU8540_FLL_CLK_SRC_MASK | NAU8540_GAIN_ERR_MASK, + NAU8540_FLL_CLK_SRC_BLK | + (0xf << NAU8540_GAIN_ERR_SFT)); break; case NAU8540_CLK_FLL_FS: regmap_update_bits(nau8540->regmap, NAU8540_REG_FLL3, - NAU8540_FLL_CLK_SRC_MASK, NAU8540_FLL_CLK_SRC_FS); + NAU8540_FLL_CLK_SRC_MASK | NAU8540_GAIN_ERR_MASK, + NAU8540_FLL_CLK_SRC_FS | + (0xf << NAU8540_GAIN_ERR_SFT)); break; default: diff --git a/sound/soc/codecs/nau8540.h b/sound/soc/codecs/nau8540.h index dceb04b23c19..732b490edf81 100644 --- a/sound/soc/codecs/nau8540.h +++ b/sound/soc/codecs/nau8540.h @@ -100,9 +100,13 @@ #define NAU8540_CLK_MCLK_SRC_MASK 0xf /* FLL1 (0x04) */ +#define NAU8540_ICTRL_LATCH_SFT 10 +#define NAU8540_ICTRL_LATCH_MASK (0x7 << NAU8540_ICTRL_LATCH_SFT) #define NAU8540_FLL_RATIO_MASK 0x7f /* FLL3 (0x06) */ +#define NAU8540_GAIN_ERR_SFT 12 +#define NAU8540_GAIN_ERR_MASK (0xf << NAU8540_GAIN_ERR_SFT) #define NAU8540_FLL_CLK_SRC_SFT 10 #define NAU8540_FLL_CLK_SRC_MASK (0x3 << NAU8540_FLL_CLK_SRC_SFT) #define NAU8540_FLL_CLK_SRC_MCLK (0 << NAU8540_FLL_CLK_SRC_SFT) @@ -127,6 +131,7 @@ /* FLL6 (0x9) */ #define NAU8540_DCO_EN (0x1 << 15) #define NAU8540_SDM_EN (0x1 << 14) +#define NAU8540_CUTOFF500 (0x1 << 13) /* PCM_CTRL0 (0x10) */ #define NAU8540_I2S_BP_SFT 7 -- cgit v1.2.3 From 080f773d226a9c2b0fa0d8f02107518c560f8b77 Mon Sep 17 00:00:00 2001 From: John Hsu Date: Mon, 13 Nov 2017 10:36:28 +0800 Subject: ASoC: nau8824: change FVCO maximum threshold Change the maximum of FDCO which remains between 90MHz-100MHz. FDCO must be within the 90MHz-100MHz or the FFL cannot be guaranteed across the full range of operation. Signed-off-by: John Hsu Signed-off-by: Mark Brown --- sound/soc/codecs/nau8824.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/codecs/nau8824.c b/sound/soc/codecs/nau8824.c index 8a9a9939827e..088e0cef4cb8 100644 --- a/sound/soc/codecs/nau8824.c +++ b/sound/soc/codecs/nau8824.c @@ -43,7 +43,7 @@ static bool nau8824_is_jack_inserted(struct nau8824 *nau8824); /* the parameter threshold of FLL */ #define NAU_FREF_MAX 13500000 -#define NAU_FVCO_MAX 124000000 +#define NAU_FVCO_MAX 100000000 #define NAU_FVCO_MIN 90000000 /* scaling for mclk from sysclk_src output */ -- cgit v1.2.3 From 226d7449135ffc62866c06d73b28cac90b3f31e4 Mon Sep 17 00:00:00 2001 From: John Hsu Date: Fri, 24 Nov 2017 18:08:26 +0800 Subject: ASoC: nau8825: disable crosstalk by default The driver makes the crosstalk funciton disabled by default which can simplify the codec function. The platform may not need this funciton and reduce the potential risk. Therefore, We change the property "nuvoton,crosstalk-bypass" to "nuvoton,crosstalk-enable". The crosstalk measurement is enabled if the property is set. Otherwise, it is disabled. Besides, add more condition in the entry point of the crosstalk sequence to disable the function completely. Signed-off-by: John Hsu Signed-off-by: Mark Brown --- .../devicetree/bindings/sound/nau8825.txt | 4 ++-- sound/soc/codecs/nau8825.c | 23 ++++++++++++---------- sound/soc/codecs/nau8825.h | 2 +- 3 files changed, 16 insertions(+), 13 deletions(-) diff --git a/Documentation/devicetree/bindings/sound/nau8825.txt b/Documentation/devicetree/bindings/sound/nau8825.txt index 2f5e973285a6..d16d96839bcb 100644 --- a/Documentation/devicetree/bindings/sound/nau8825.txt +++ b/Documentation/devicetree/bindings/sound/nau8825.txt @@ -69,7 +69,7 @@ Optional properties: - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms - - nuvoton,crosstalk-bypass: make crosstalk function bypass if set. + - nuvoton,crosstalk-enable: make crosstalk function enable if set. - clocks: list of phandle and clock specifier pairs according to common clock bindings for the clocks described in clock-names @@ -98,7 +98,7 @@ Example: nuvoton,short-key-debounce = <2>; nuvoton,jack-insert-debounce = <7>; nuvoton,jack-eject-debounce = <7>; - nuvoton,crosstalk-bypass; + nuvoton,crosstalk-enable; clock-names = "mclk"; clocks = <&tegra_car TEGRA210_CLK_CLK_OUT_2>; diff --git a/sound/soc/codecs/nau8825.c b/sound/soc/codecs/nau8825.c index 714ce17da717..d3c1a02f1e15 100644 --- a/sound/soc/codecs/nau8825.c +++ b/sound/soc/codecs/nau8825.c @@ -815,11 +815,12 @@ static void nau8825_xtalk_work(struct work_struct *work) static void nau8825_xtalk_cancel(struct nau8825 *nau8825) { - /* If the xtalk_protect is true, that means the process is still - * on going. The driver forces to cancel the cross talk task and + /* If the crosstalk is eanbled and the process is on going, + * the driver forces to cancel the crosstalk task and * restores the configuration to original status. */ - if (nau8825->xtalk_protect) { + if (nau8825->xtalk_enable && nau8825->xtalk_state != + NAU8825_XTALK_DONE) { cancel_work_sync(&nau8825->xtalk_work); nau8825_xtalk_clean(nau8825); } @@ -1686,7 +1687,7 @@ static irqreturn_t nau8825_interrupt(int irq, void *data) } else if (active_irq & NAU8825_HEADSET_COMPLETION_IRQ) { if (nau8825_is_jack_inserted(regmap)) { event |= nau8825_jack_insert(nau8825); - if (!nau8825->xtalk_bypass && !nau8825->high_imped) { + if (nau8825->xtalk_enable && !nau8825->high_imped) { /* Apply the cross talk suppression in the * headset without high impedance. */ @@ -1732,8 +1733,10 @@ static irqreturn_t nau8825_interrupt(int irq, void *data) nau8825->xtalk_event_mask = event_mask; } } else if (active_irq & NAU8825_IMPEDANCE_MEAS_IRQ) { - schedule_work(&nau8825->xtalk_work); - clear_irq = NAU8825_IMPEDANCE_MEAS_IRQ; + if (nau8825->xtalk_enable) { + schedule_work(&nau8825->xtalk_work); + clear_irq = NAU8825_IMPEDANCE_MEAS_IRQ; + } } else if ((active_irq & NAU8825_JACK_INSERTION_IRQ_MASK) == NAU8825_JACK_INSERTION_DETECTED) { /* One more step to check GPIO status directly. Thus, the @@ -2440,8 +2443,8 @@ static void nau8825_print_device_properties(struct nau8825 *nau8825) nau8825->jack_insert_debounce); dev_dbg(dev, "jack-eject-debounce: %d\n", nau8825->jack_eject_debounce); - dev_dbg(dev, "crosstalk-bypass: %d\n", - nau8825->xtalk_bypass); + dev_dbg(dev, "crosstalk-enable: %d\n", + nau8825->xtalk_enable); } static int nau8825_read_device_properties(struct device *dev, @@ -2506,8 +2509,8 @@ static int nau8825_read_device_properties(struct device *dev, &nau8825->jack_eject_debounce); if (ret) nau8825->jack_eject_debounce = 0; - nau8825->xtalk_bypass = device_property_read_bool(dev, - "nuvoton,crosstalk-bypass"); + nau8825->xtalk_enable = device_property_read_bool(dev, + "nuvoton,crosstalk-enable"); nau8825->mclk = devm_clk_get(dev, "mclk"); if (PTR_ERR(nau8825->mclk) == -EPROBE_DEFER) { diff --git a/sound/soc/codecs/nau8825.h b/sound/soc/codecs/nau8825.h index 8aee5c8647ae..199d6ea4dcdc 100644 --- a/sound/soc/codecs/nau8825.h +++ b/sound/soc/codecs/nau8825.h @@ -476,7 +476,7 @@ struct nau8825 { int xtalk_event_mask; bool xtalk_protect; int imp_rms[NAU8825_XTALK_IMM]; - int xtalk_bypass; + int xtalk_enable; }; int nau8825_enable_jack_detect(struct snd_soc_codec *codec, -- cgit v1.2.3 From e3fee43a968fd39dcc56be3757fcdfe250964125 Mon Sep 17 00:00:00 2001 From: John Hsu Date: Thu, 30 Nov 2017 10:13:17 +0800 Subject: ASoC: nau8825: set clear_irq when imm IRQ happened Although the crosstalk is disabled, it is better to set clear_irq properly when the impedance measurement interrupt happens. It can avoid that the driver clears other IRQs by accident if the active_irq has another IRQ events. Signed-off-by: John Hsu Reviewed-by: Wu-Cheng Li Tested-by: Wu-Cheng Li Signed-off-by: Mark Brown --- sound/soc/codecs/nau8825.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/sound/soc/codecs/nau8825.c b/sound/soc/codecs/nau8825.c index d3c1a02f1e15..603cd72c2a25 100644 --- a/sound/soc/codecs/nau8825.c +++ b/sound/soc/codecs/nau8825.c @@ -1733,10 +1733,9 @@ static irqreturn_t nau8825_interrupt(int irq, void *data) nau8825->xtalk_event_mask = event_mask; } } else if (active_irq & NAU8825_IMPEDANCE_MEAS_IRQ) { - if (nau8825->xtalk_enable) { + if (nau8825->xtalk_enable) schedule_work(&nau8825->xtalk_work); - clear_irq = NAU8825_IMPEDANCE_MEAS_IRQ; - } + clear_irq = NAU8825_IMPEDANCE_MEAS_IRQ; } else if ((active_irq & NAU8825_JACK_INSERTION_IRQ_MASK) == NAU8825_JACK_INSERTION_DETECTED) { /* One more step to check GPIO status directly. Thus, the -- cgit v1.2.3 From 70424d8e6e15abd32e189130be220d0063e082bc Mon Sep 17 00:00:00 2001 From: John Hsu Date: Fri, 1 Dec 2017 10:01:50 +0800 Subject: ASoC: nau8825: improve semaphore control After reviewing the crosstalk protection, there are two flaws at semaphore control. The first one is that the semaphore releases are not enough; and the other is that down_interruptible has an risk to make the ISR sleep. Therefore, the driver add more releases before the funcitons return. Take down_trylock to replace down_interruptible. The ISR can control the protection as well and never sleep by semaphore. Signed-off-by: John Hsu Signed-off-by: Mark Brown --- sound/soc/codecs/nau8825.c | 38 +++++++++++++++++++++++--------------- 1 file changed, 23 insertions(+), 15 deletions(-) diff --git a/sound/soc/codecs/nau8825.c b/sound/soc/codecs/nau8825.c index 603cd72c2a25..5778eadbf9e6 100644 --- a/sound/soc/codecs/nau8825.c +++ b/sound/soc/codecs/nau8825.c @@ -245,13 +245,14 @@ static const unsigned short logtable[256] = { * tasks are allowed to acquire the semaphore, calling this function will * put the task to sleep. If the semaphore is not released within the * specified number of jiffies, this function returns. - * Acquires the semaphore without jiffies. If no more tasks are allowed - * to acquire the semaphore, calling this function will put the task to - * sleep until the semaphore is released. * If the semaphore is not released within the specified number of jiffies, - * this function returns -ETIME. - * If the sleep is interrupted by a signal, this function will return -EINTR. - * It returns 0 if the semaphore was acquired successfully. + * this function returns -ETIME. If the sleep is interrupted by a signal, + * this function will return -EINTR. It returns 0 if the semaphore was + * acquired successfully. + * + * Acquires the semaphore without jiffies. Try to acquire the semaphore + * atomically. Returns 0 if the semaphore has been acquired successfully + * or 1 if it it cannot be acquired. */ static int nau8825_sema_acquire(struct nau8825 *nau8825, long timeout) { @@ -262,8 +263,8 @@ static int nau8825_sema_acquire(struct nau8825 *nau8825, long timeout) if (ret < 0) dev_warn(nau8825->dev, "Acquire semaphore timeout\n"); } else { - ret = down_interruptible(&nau8825->xtalk_sem); - if (ret < 0) + ret = down_trylock(&nau8825->xtalk_sem); + if (ret) dev_warn(nau8825->dev, "Acquire semaphore fail\n"); } @@ -1246,8 +1247,10 @@ static int nau8825_hw_params(struct snd_pcm_substream *substream, regmap_read(nau8825->regmap, NAU8825_REG_DAC_CTRL1, &osr); osr &= NAU8825_DAC_OVERSAMPLE_MASK; if (nau8825_clock_check(nau8825, substream->stream, - params_rate(params), osr)) + params_rate(params), osr)) { + nau8825_sema_release(nau8825); return -EINVAL; + } regmap_update_bits(nau8825->regmap, NAU8825_REG_CLK_DIVIDER, NAU8825_CLK_DAC_SRC_MASK, osr_dac_sel[osr].clk_src << NAU8825_CLK_DAC_SRC_SFT); @@ -1255,8 +1258,10 @@ static int nau8825_hw_params(struct snd_pcm_substream *substream, regmap_read(nau8825->regmap, NAU8825_REG_ADC_RATE, &osr); osr &= NAU8825_ADC_SYNC_DOWN_MASK; if (nau8825_clock_check(nau8825, substream->stream, - params_rate(params), osr)) + params_rate(params), osr)) { + nau8825_sema_release(nau8825); return -EINVAL; + } regmap_update_bits(nau8825->regmap, NAU8825_REG_CLK_DIVIDER, NAU8825_CLK_ADC_SRC_MASK, osr_adc_sel[osr].clk_src << NAU8825_CLK_ADC_SRC_SFT); @@ -1273,8 +1278,10 @@ static int nau8825_hw_params(struct snd_pcm_substream *substream, bclk_div = 1; else if (bclk_fs <= 128) bclk_div = 0; - else + else { + nau8825_sema_release(nau8825); return -EINVAL; + } regmap_update_bits(nau8825->regmap, NAU8825_REG_I2S_PCM_CTRL2, NAU8825_I2S_LRC_DIV_MASK | NAU8825_I2S_BLK_DIV_MASK, ((bclk_div + 1) << NAU8825_I2S_LRC_DIV_SFT) | bclk_div); @@ -1294,6 +1301,7 @@ static int nau8825_hw_params(struct snd_pcm_substream *substream, val_len |= NAU8825_I2S_DL_32; break; default: + nau8825_sema_release(nau8825); return -EINVAL; } @@ -1312,8 +1320,6 @@ static int nau8825_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt) struct nau8825 *nau8825 = snd_soc_codec_get_drvdata(codec); unsigned int ctrl1_val = 0, ctrl2_val = 0; - nau8825_sema_acquire(nau8825, 3 * HZ); - switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { case SND_SOC_DAIFMT_CBM_CFM: ctrl2_val |= NAU8825_I2S_MS_MASTER; @@ -1355,6 +1361,8 @@ static int nau8825_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt) return -EINVAL; } + nau8825_sema_acquire(nau8825, 3 * HZ); + regmap_update_bits(nau8825->regmap, NAU8825_REG_I2S_PCM_CTRL1, NAU8825_I2S_DL_MASK | NAU8825_I2S_DF_MASK | NAU8825_I2S_BP_MASK | NAU8825_I2S_PCMB_MASK, @@ -1701,7 +1709,7 @@ static irqreturn_t nau8825_interrupt(int irq, void *data) int ret; nau8825->xtalk_protect = true; ret = nau8825_sema_acquire(nau8825, 0); - if (ret < 0) + if (ret) nau8825->xtalk_protect = false; } /* Startup cross talk detection process */ @@ -2383,7 +2391,7 @@ static int __maybe_unused nau8825_resume(struct snd_soc_codec *codec) regcache_sync(nau8825->regmap); nau8825->xtalk_protect = true; ret = nau8825_sema_acquire(nau8825, 0); - if (ret < 0) + if (ret) nau8825->xtalk_protect = false; enable_irq(nau8825->irq); -- cgit v1.2.3 From fa25b4f59f1de9536104b632ec4c4c0b8f8e54ec Mon Sep 17 00:00:00 2001 From: John Hsu Date: Fri, 1 Dec 2017 10:01:37 +0800 Subject: ASoC: nau8825: improve crosstalk measurement protection The sequence of crosstalk measurement is not robust. The driver add more protections to make it stronger. The improvements as follows: (1)Give backup table the default value. The values are the same with the default of hardware registers. The impact will decline once restoring the backup table in the wrong way. (2)Add xtalk_baktab_initialized flag. The flag can keep the initiation status of backup table. It helps to backup and restore the backup-table correctly. (3)Add cancel parameter in the restore function. The volume ramping should do in crosstalk DONE state only. Otherwise, the delay action is not allowed because the restore may happen during the jack eject interruption. (4)Add xtalk_protect condition check before scheduling work in ISR. It makes sure the semaphore hold during the crosstalk measurement. The sequence is still under protection from playback interference. Signed-off-by: John Hsu Signed-off-by: Mark Brown --- sound/soc/codecs/nau8825.c | 45 +++++++++++++++++++++++++++++++-------------- sound/soc/codecs/nau8825.h | 1 + 2 files changed, 32 insertions(+), 14 deletions(-) diff --git a/sound/soc/codecs/nau8825.c b/sound/soc/codecs/nau8825.c index 5778eadbf9e6..2aea642b4a5d 100644 --- a/sound/soc/codecs/nau8825.c +++ b/sound/soc/codecs/nau8825.c @@ -194,10 +194,10 @@ static const struct reg_default nau8825_reg_defaults[] = { /* register backup table when cross talk detection */ static struct reg_default nau8825_xtalk_baktab[] = { - { NAU8825_REG_ADC_DGAIN_CTRL, 0 }, + { NAU8825_REG_ADC_DGAIN_CTRL, 0x00cf }, { NAU8825_REG_HSVOL_CTRL, 0 }, - { NAU8825_REG_DACL_CTRL, 0 }, - { NAU8825_REG_DACR_CTRL, 0 }, + { NAU8825_REG_DACL_CTRL, 0x00cf }, + { NAU8825_REG_DACR_CTRL, 0x02cf }, }; static const unsigned short logtable[256] = { @@ -455,22 +455,32 @@ static void nau8825_xtalk_backup(struct nau8825 *nau8825) { int i; + if (nau8825->xtalk_baktab_initialized) + return; + /* Backup some register values to backup table */ for (i = 0; i < ARRAY_SIZE(nau8825_xtalk_baktab); i++) regmap_read(nau8825->regmap, nau8825_xtalk_baktab[i].reg, &nau8825_xtalk_baktab[i].def); + + nau8825->xtalk_baktab_initialized = true; } -static void nau8825_xtalk_restore(struct nau8825 *nau8825) +static void nau8825_xtalk_restore(struct nau8825 *nau8825, bool cause_cancel) { int i, volume; + if (!nau8825->xtalk_baktab_initialized) + return; + /* Restore register values from backup table; When the driver restores - * the headphone volumem, it needs recover to original level gradually - * with 3dB per step for less pop noise. + * the headphone volume in XTALK_DONE state, it needs recover to + * original level gradually with 3dB per step for less pop noise. + * Otherwise, the restore should do ASAP. */ for (i = 0; i < ARRAY_SIZE(nau8825_xtalk_baktab); i++) { - if (nau8825_xtalk_baktab[i].reg == NAU8825_REG_HSVOL_CTRL) { + if (!cause_cancel && nau8825_xtalk_baktab[i].reg == + NAU8825_REG_HSVOL_CTRL) { /* Ramping up the volume change to reduce pop noise */ volume = nau8825_xtalk_baktab[i].def & NAU8825_HPR_VOL_MASK; @@ -480,6 +490,8 @@ static void nau8825_xtalk_restore(struct nau8825 *nau8825) regmap_write(nau8825->regmap, nau8825_xtalk_baktab[i].reg, nau8825_xtalk_baktab[i].def); } + + nau8825->xtalk_baktab_initialized = false; } static void nau8825_xtalk_prepare_dac(struct nau8825 *nau8825) @@ -645,7 +657,7 @@ static void nau8825_xtalk_clean_adc(struct nau8825 *nau8825) NAU8825_POWERUP_ADCL | NAU8825_ADC_VREFSEL_MASK, 0); } -static void nau8825_xtalk_clean(struct nau8825 *nau8825) +static void nau8825_xtalk_clean(struct nau8825 *nau8825, bool cause_cancel) { /* Enable internal VCO needed for interruptions */ nau8825_configure_sysclk(nau8825, NAU8825_CLK_INTERNAL, 0); @@ -661,7 +673,7 @@ static void nau8825_xtalk_clean(struct nau8825 *nau8825) NAU8825_I2S_MS_MASK | NAU8825_I2S_LRC_DIV_MASK | NAU8825_I2S_BLK_DIV_MASK, NAU8825_I2S_MS_SLAVE); /* Restore value of specific register for cross talk */ - nau8825_xtalk_restore(nau8825); + nau8825_xtalk_restore(nau8825, cause_cancel); } static void nau8825_xtalk_imm_start(struct nau8825 *nau8825, int vol) @@ -780,7 +792,7 @@ static void nau8825_xtalk_measure(struct nau8825 *nau8825) dev_dbg(nau8825->dev, "cross talk sidetone: %x\n", sidetone); regmap_write(nau8825->regmap, NAU8825_REG_DAC_DGAIN_CTRL, (sidetone << 8) | sidetone); - nau8825_xtalk_clean(nau8825); + nau8825_xtalk_clean(nau8825, false); nau8825->xtalk_state = NAU8825_XTALK_DONE; break; default: @@ -823,7 +835,7 @@ static void nau8825_xtalk_cancel(struct nau8825 *nau8825) if (nau8825->xtalk_enable && nau8825->xtalk_state != NAU8825_XTALK_DONE) { cancel_work_sync(&nau8825->xtalk_work); - nau8825_xtalk_clean(nau8825); + nau8825_xtalk_clean(nau8825, true); } /* Reset parameters for cross talk suppression function */ nau8825_sema_reset(nau8825); @@ -1713,8 +1725,11 @@ static irqreturn_t nau8825_interrupt(int irq, void *data) nau8825->xtalk_protect = false; } /* Startup cross talk detection process */ - nau8825->xtalk_state = NAU8825_XTALK_PREPARE; - schedule_work(&nau8825->xtalk_work); + if (nau8825->xtalk_protect) { + nau8825->xtalk_state = + NAU8825_XTALK_PREPARE; + schedule_work(&nau8825->xtalk_work); + } } else { /* The cross talk suppression shouldn't apply * in the headset with high impedance. Thus, @@ -1741,7 +1756,8 @@ static irqreturn_t nau8825_interrupt(int irq, void *data) nau8825->xtalk_event_mask = event_mask; } } else if (active_irq & NAU8825_IMPEDANCE_MEAS_IRQ) { - if (nau8825->xtalk_enable) + /* crosstalk detection enable and process on going */ + if (nau8825->xtalk_enable && nau8825->xtalk_protect) schedule_work(&nau8825->xtalk_work); clear_irq = NAU8825_IMPEDANCE_MEAS_IRQ; } else if ((active_irq & NAU8825_JACK_INSERTION_IRQ_MASK) == @@ -2578,6 +2594,7 @@ static int nau8825_i2c_probe(struct i2c_client *i2c, */ nau8825->xtalk_state = NAU8825_XTALK_DONE; nau8825->xtalk_protect = false; + nau8825->xtalk_baktab_initialized = false; sema_init(&nau8825->xtalk_sem, 1); INIT_WORK(&nau8825->xtalk_work, nau8825_xtalk_work); diff --git a/sound/soc/codecs/nau8825.h b/sound/soc/codecs/nau8825.h index 199d6ea4dcdc..f7e732125882 100644 --- a/sound/soc/codecs/nau8825.h +++ b/sound/soc/codecs/nau8825.h @@ -477,6 +477,7 @@ struct nau8825 { bool xtalk_protect; int imp_rms[NAU8825_XTALK_IMM]; int xtalk_enable; + bool xtalk_baktab_initialized; /* True if initialized. */ }; int nau8825_enable_jack_detect(struct snd_soc_codec *codec, -- cgit v1.2.3 From 949293d45d6b0951e2dfdfd670a9c0092b10fd27 Mon Sep 17 00:00:00 2001 From: Christian Fischer Date: Fri, 12 Jan 2018 14:22:59 +0100 Subject: ASoC: mxs-sgtl5000: add audio-routing support Add dapm_widgets to machine-driver (from imx-sgtl5000). If the "audio-routing"-property is present at probing the dapm-widgets getting linked to the card. Signed-off-by: Christian Fischer Signed-off-by: Mark Brown --- .../bindings/sound/mxs-audio-sgtl5000.txt | 33 +++++++++++++++++++--- sound/soc/mxs/mxs-sgtl5000.c | 20 +++++++++++++ 2 files changed, 49 insertions(+), 4 deletions(-) diff --git a/Documentation/devicetree/bindings/sound/mxs-audio-sgtl5000.txt b/Documentation/devicetree/bindings/sound/mxs-audio-sgtl5000.txt index 601c518eddaa..4eb980bd0287 100644 --- a/Documentation/devicetree/bindings/sound/mxs-audio-sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/mxs-audio-sgtl5000.txt @@ -1,10 +1,31 @@ * Freescale MXS audio complex with SGTL5000 codec Required properties: -- compatible: "fsl,mxs-audio-sgtl5000" -- model: The user-visible name of this sound complex -- saif-controllers: The phandle list of the MXS SAIF controller -- audio-codec: The phandle of the SGTL5000 audio codec +- compatible : "fsl,mxs-audio-sgtl5000" +- model : The user-visible name of this sound complex +- saif-controllers : The phandle list of the MXS SAIF controller +- audio-codec : The phandle of the SGTL5000 audio codec +- audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names could be power supplies, SGTL5000 + pins, and the jacks on the board: + + Power supplies: + * Mic Bias + + SGTL5000 pins: + * MIC_IN + * LINE_IN + * HP_OUT + * LINE_OUT + + Board connectors: + * Mic Jack + * Line In Jack + * Headphone Jack + * Line Out Jack + * Ext Spk Example: @@ -14,4 +35,8 @@ sound { model = "imx28-evk-sgtl5000"; saif-controllers = <&saif0 &saif1>; audio-codec = <&sgtl5000>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; }; diff --git a/sound/soc/mxs/mxs-sgtl5000.c b/sound/soc/mxs/mxs-sgtl5000.c index 2ed3240cc682..b593f76212e0 100644 --- a/sound/soc/mxs/mxs-sgtl5000.c +++ b/sound/soc/mxs/mxs-sgtl5000.c @@ -93,6 +93,14 @@ static struct snd_soc_dai_link mxs_sgtl5000_dai[] = { }, }; +static const struct snd_soc_dapm_widget mxs_sgtl5000_dapm_widgets[] = { + SND_SOC_DAPM_MIC("Mic Jack", NULL), + SND_SOC_DAPM_LINE("Line In Jack", NULL), + SND_SOC_DAPM_HP("Headphone Jack", NULL), + SND_SOC_DAPM_SPK("Line Out Jack", NULL), + SND_SOC_DAPM_SPK("Ext Spk", NULL), +}; + static struct snd_soc_card mxs_sgtl5000 = { .name = "mxs_sgtl5000", .owner = THIS_MODULE, @@ -141,6 +149,18 @@ static int mxs_sgtl5000_probe(struct platform_device *pdev) card->dev = &pdev->dev; + if (of_find_property(np, "audio-routing", NULL)) { + card->dapm_widgets = mxs_sgtl5000_dapm_widgets; + card->num_dapm_widgets = ARRAY_SIZE(mxs_sgtl5000_dapm_widgets); + + ret = snd_soc_of_parse_audio_routing(card, "audio-routing"); + if (ret) { + dev_err(&pdev->dev, "failed to parse audio-routing (%d)\n", + ret); + return ret; + } + } + ret = devm_snd_soc_register_card(&pdev->dev, card); if (ret) { dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", -- cgit v1.2.3 From d04c413f2ab3aa5998bf86f7a2f6235ed82b2ee2 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Wed, 17 Jan 2018 13:48:55 -0200 Subject: ASoC: mxs-sgtl5000: Do not print error on probe deferral Probe deferral may happen, so do not print an error message in this case. Signed-off-by: Fabio Estevam Signed-off-by: Mark Brown --- sound/soc/mxs/mxs-sgtl5000.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/sound/soc/mxs/mxs-sgtl5000.c b/sound/soc/mxs/mxs-sgtl5000.c index 2ed3240cc682..5a871f25f438 100644 --- a/sound/soc/mxs/mxs-sgtl5000.c +++ b/sound/soc/mxs/mxs-sgtl5000.c @@ -143,8 +143,9 @@ static int mxs_sgtl5000_probe(struct platform_device *pdev) ret = devm_snd_soc_register_card(&pdev->dev, card); if (ret) { - dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", - ret); + if (ret != -EPROBE_DEFER) + dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", + ret); return ret; } -- cgit v1.2.3