From 6f75aaa72af19d3e4d144e13d59e71f51686b77f Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Fri, 19 Oct 2007 18:13:33 +0100 Subject: [MIPS] Delete totally outdated Documentation/mips/time.README Signed-off-by: Ralf Baechle --- Documentation/mips/00-INDEX | 2 - Documentation/mips/time.README | 173 ----------------------------------------- 2 files changed, 175 deletions(-) delete mode 100644 Documentation/mips/time.README diff --git a/Documentation/mips/00-INDEX b/Documentation/mips/00-INDEX index 9df8a2eac7b4..3f13bf8043d2 100644 --- a/Documentation/mips/00-INDEX +++ b/Documentation/mips/00-INDEX @@ -4,5 +4,3 @@ AU1xxx_IDE.README - README for MIPS AU1XXX IDE driver. GT64120.README - README for dir with info on MIPS boards using GT-64120 or GT-64120A. -time.README - - README for MIPS time services. diff --git a/Documentation/mips/time.README b/Documentation/mips/time.README deleted file mode 100644 index a4ce603ed3b3..000000000000 --- a/Documentation/mips/time.README +++ /dev/null @@ -1,173 +0,0 @@ -README for MIPS time services - -Jun Sun -jsun@mvista.com or jsun@junsun.net - - -ABOUT ------ -This file describes the new arch/mips/kernel/time.c, related files and the -services they provide. - -If you are short in patience and just want to know how to use time.c for a -new board or convert an existing board, go to the last section. - - -FILES, COMPATABILITY AND CONFIGS ---------------------------------- - -The old arch/mips/kernel/time.c is renamed to old-time.c. - -A new time.c is put there, together with include/asm-mips/time.h. - -Two configs variables are introduced, CONFIG_OLD_TIME_C and CONFIG_NEW_TIME_C. -So we allow boards using - - 1) old time.c (CONFIG_OLD_TIME_C) - 2) new time.c (CONFIG_NEW_TIME_C) - 3) neither (their own private time.c) - -However, it is expected every board will move to the new time.c in the near -future. - - -WHAT THE NEW CODE PROVIDES? ---------------------------- - -The new time code provide the following services: - - a) Implements functions required by Linux common code: - time_init - - b) provides an abstraction of RTC and null RTC implementation as default. - extern unsigned long (*rtc_get_time)(void); - extern int (*rtc_set_time)(unsigned long); - - c) high-level and low-level timer interrupt routines where the timer - interrupt source may or may not be the CPU timer. The high-level - routine is dispatched through do_IRQ() while the low-level is - dispatched in assemably code (usually int-handler.S) - - -WHAT THE NEW CODE REQUIRES? ---------------------------- - -For the new code to work properly, each board implementation needs to supply -the following functions or values: - - a) board_time_init - a function pointer. Invoked at the beginnig of - time_init(). It is optional. - 1. (optional) set up RTC routines - 2. (optional) calibrate and set the mips_hpt_frequency - - b) plat_timer_setup - a function pointer. Invoked at the end of time_init() - 1. (optional) over-ride any decisions made in time_init() - 2. set up the irqaction for timer interrupt. - 3. enable the timer interrupt - - c) (optional) board-specific RTC routines. - - d) (optional) mips_hpt_frequency - It must be definied if the board - is using CPU counter for timer interrupt. - - -PORTING GUIDE -------------- - -Step 1: decide how you like to implement the time services. - - a) does this board have a RTC? If yes, implement the two RTC funcs. - - b) does the CPU have counter/compare registers? - - If the answer is no, you need a timer to provide the timer interrupt - at 100 HZ speed. - - c) The following sub steps assume your CPU has counter register. - Do you plan to use the CPU counter register as the timer interrupt - or use an exnternal timer? - - In order to use CPU counter register as the timer interrupt source, you - must know the counter speed (mips_hpt_frequency). It is usually the - same as the CPU speed or an integral divisor of it. - - d) decide on whether you want to use high-level or low-level timer - interrupt routines. The low-level one is presumably faster, but should - not make too mcuh difference. - - -Step 2: the machine setup() function - - If you supply board_time_init(), set the function poointer. - - -Step 3: implement rtc routines, board_time_init() and plat_timer_setup() - if needed. - - board_time_init() - - a) (optional) set up RTC routines, - b) (optional) calibrate and set the mips_hpt_frequency - (only needed if you intended to use cpu counter as timer interrupt - source) - - plat_timer_setup() - - a) (optional) over-write any choices made above by time_init(). - b) machine specific code should setup the timer irqaction. - c) enable the timer interrupt - - - If the RTC chip is a common chip, I suggest the routines are put under - arch/mips/libs. For example, for DS1386 chip, one would create - rtc-ds1386.c under arch/mips/lib directory. Add the following line to - the arch/mips/lib/Makefile: - - obj-$(CONFIG_DDB5476) += rtc-ds1386.o - -Step 4: if you are using low-level timer interrupt, change your interrupt - dispathcing code to check for timer interrupt and jump to - ll_timer_interrupt() directly if one is detected. - -Step 5: Modify arch/mips/config.in and add CONFIG_NEW_TIME_C to your machine. - Modify the appropriate defconfig if applicable. - -Final notes: - -For some tricky cases, you may need to add your own wrapper functions -for some of the functions in time.c. - -For example, you may define your own timer interrupt routine, which does -some of its own processing and then calls timer_interrupt(). - -You can also over-ride any of the built-in functions (RTC routines -and/or timer interrupt routine). - - -PORTING NOTES FOR SMP ----------------------- - -If you have a SMP box, things are slightly more complicated. - -The time service running every jiffy is logically divided into two parts: - - 1) the one for the whole system (defined in timer_interrupt()) - 2) the one that should run for each CPU (defined in local_timer_interrupt()) - -You need to decide on your timer interrupt sources. - - case 1) - whole system has only one timer interrupt delivered to one CPU - - In this case, you set up timer interrupt as in UP systems. In addtion, - you need to set emulate_local_timer_interrupt to 1 so that other - CPUs get to call local_timer_interrupt(). - - THIS IS CURRENTLY NOT IMPLEMNETED. However, it is rather easy to write - one should such a need arise. You simply make a IPI call. - - case 2) - each CPU has a separate timer interrupt - - In this case, you need to set up IRQ such that each of them will - call local_timer_interrupt(). In addition, you need to arrange - one and only one of them to call timer_interrupt(). - - You can also do the low-level version of those interrupt routines, - following similar dispatching routes described above. -- cgit v1.2.3