From d96be879ff469759af6d7fcebdb66237c18da6f8 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Tue, 6 Jan 2009 17:04:14 +0100 Subject: mmc: Add a MX2/MX3 specific SDHC driver This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically the same as in the MX1, but unlike the MX1 controller the MX2 controller just works as expected. Since the MX1 driver has more workarounds for bugs than anything else I had no success with supporting MX1 and MX2 in a sane way in one driver. Signed-off-by: Sascha Hauer Signed-off-by: Pierre Ossman --- arch/arm/plat-mxc/include/mach/mmc.h | 36 ++ drivers/mmc/host/Kconfig | 10 + drivers/mmc/host/Makefile | 1 + drivers/mmc/host/mxcmmc.c | 880 +++++++++++++++++++++++++++++++++++ 4 files changed, 927 insertions(+) create mode 100644 arch/arm/plat-mxc/include/mach/mmc.h create mode 100644 drivers/mmc/host/mxcmmc.c diff --git a/arch/arm/plat-mxc/include/mach/mmc.h b/arch/arm/plat-mxc/include/mach/mmc.h new file mode 100644 index 000000000000..de2128dada5c --- /dev/null +++ b/arch/arm/plat-mxc/include/mach/mmc.h @@ -0,0 +1,36 @@ +#ifndef ASMARM_ARCH_MMC_H +#define ASMARM_ARCH_MMC_H + +#include + +struct device; + +/* board specific SDHC data, optional. + * If not present, a writable card with 3,3V is assumed. + */ +struct imxmmc_platform_data { + /* Return values for the get_ro callback should be: + * 0 for a read/write card + * 1 for a read-only card + * -ENOSYS when not supported (equal to NULL callback) + * or a negative errno value when something bad happened + */ + int (*get_ro)(struct device *); + + /* board specific hook to (de)initialize the SD slot. + * The board code can call 'handler' on a card detection + * change giving data as argument. + */ + int (*init)(struct device *dev, irq_handler_t handler, void *data); + void (*exit)(struct device *dev, void *data); + + /* available voltages. If not given, assume + * MMC_VDD_32_33 | MMC_VDD_33_34 + */ + unsigned int ocr_avail; + + /* adjust slot voltage */ + void (*setpower)(struct device *, unsigned int vdd); +}; + +#endif diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index 0efa390978bd..99d4b28d52ed 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -145,6 +145,16 @@ config MMC_IMX If unsure, say N. +config MMC_MXC + tristate "Freescale i.MX2/3 Multimedia Card Interface support" + depends on ARCH_MXC + help + This selects the Freescale i.MX2/3 Multimedia card Interface. + If you have a i.MX platform with a Multimedia Card slot, + say Y or M here. + + If unsure, say N. + config MMC_TIFM_SD tristate "TI Flash Media MMC/SD Interface support (EXPERIMENTAL)" depends on EXPERIMENTAL && PCI diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile index 98cab84829b8..dedec55861d9 100644 --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -9,6 +9,7 @@ endif obj-$(CONFIG_MMC_ARMMMCI) += mmci.o obj-$(CONFIG_MMC_PXA) += pxamci.o obj-$(CONFIG_MMC_IMX) += imxmmc.o +obj-$(CONFIG_MMC_MXC) += mxcmmc.o obj-$(CONFIG_MMC_SDHCI) += sdhci.o obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o obj-$(CONFIG_MMC_RICOH_MMC) += ricoh_mmc.o diff --git a/drivers/mmc/host/mxcmmc.c b/drivers/mmc/host/mxcmmc.c new file mode 100644 index 000000000000..dda0be4e25dc --- /dev/null +++ b/drivers/mmc/host/mxcmmc.c @@ -0,0 +1,880 @@ +/* + * linux/drivers/mmc/host/mxcmmc.c - Freescale i.MX MMCI driver + * + * This is a driver for the SDHC controller found in Freescale MX2/MX3 + * SoCs. It is basically the same hardware as found on MX1 (imxmmc.c). + * Unlike the hardware found on MX1, this hardware just works and does + * not need all the quirks found in imxmmc.c, hence the seperate driver. + * + * Copyright (C) 2008 Sascha Hauer, Pengutronix + * Copyright (C) 2006 Pavel Pisa, PiKRON + * + * derived from pxamci.c by Russell King + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#ifdef CONFIG_ARCH_MX2 +#include +#define HAS_DMA +#endif + +#define DRIVER_NAME "imx-mmc" + +#define MMC_REG_STR_STP_CLK 0x00 +#define MMC_REG_STATUS 0x04 +#define MMC_REG_CLK_RATE 0x08 +#define MMC_REG_CMD_DAT_CONT 0x0C +#define MMC_REG_RES_TO 0x10 +#define MMC_REG_READ_TO 0x14 +#define MMC_REG_BLK_LEN 0x18 +#define MMC_REG_NOB 0x1C +#define MMC_REG_REV_NO 0x20 +#define MMC_REG_INT_CNTR 0x24 +#define MMC_REG_CMD 0x28 +#define MMC_REG_ARG 0x2C +#define MMC_REG_RES_FIFO 0x34 +#define MMC_REG_BUFFER_ACCESS 0x38 + +#define STR_STP_CLK_RESET (1 << 3) +#define STR_STP_CLK_START_CLK (1 << 1) +#define STR_STP_CLK_STOP_CLK (1 << 0) + +#define STATUS_CARD_INSERTION (1 << 31) +#define STATUS_CARD_REMOVAL (1 << 30) +#define STATUS_YBUF_EMPTY (1 << 29) +#define STATUS_XBUF_EMPTY (1 << 28) +#define STATUS_YBUF_FULL (1 << 27) +#define STATUS_XBUF_FULL (1 << 26) +#define STATUS_BUF_UND_RUN (1 << 25) +#define STATUS_BUF_OVFL (1 << 24) +#define STATUS_SDIO_INT_ACTIVE (1 << 14) +#define STATUS_END_CMD_RESP (1 << 13) +#define STATUS_WRITE_OP_DONE (1 << 12) +#define STATUS_DATA_TRANS_DONE (1 << 11) +#define STATUS_READ_OP_DONE (1 << 11) +#define STATUS_WR_CRC_ERROR_CODE_MASK (3 << 10) +#define STATUS_CARD_BUS_CLK_RUN (1 << 8) +#define STATUS_BUF_READ_RDY (1 << 7) +#define STATUS_BUF_WRITE_RDY (1 << 6) +#define STATUS_RESP_CRC_ERR (1 << 5) +#define STATUS_CRC_READ_ERR (1 << 3) +#define STATUS_CRC_WRITE_ERR (1 << 2) +#define STATUS_TIME_OUT_RESP (1 << 1) +#define STATUS_TIME_OUT_READ (1 << 0) +#define STATUS_ERR_MASK 0x2f + +#define CMD_DAT_CONT_CMD_RESP_LONG_OFF (1 << 12) +#define CMD_DAT_CONT_STOP_READWAIT (1 << 11) +#define CMD_DAT_CONT_START_READWAIT (1 << 10) +#define CMD_DAT_CONT_BUS_WIDTH_4 (2 << 8) +#define CMD_DAT_CONT_INIT (1 << 7) +#define CMD_DAT_CONT_WRITE (1 << 4) +#define CMD_DAT_CONT_DATA_ENABLE (1 << 3) +#define CMD_DAT_CONT_RESPONSE_48BIT_CRC (1 << 0) +#define CMD_DAT_CONT_RESPONSE_136BIT (2 << 0) +#define CMD_DAT_CONT_RESPONSE_48BIT (3 << 0) + +#define INT_SDIO_INT_WKP_EN (1 << 18) +#define INT_CARD_INSERTION_WKP_EN (1 << 17) +#define INT_CARD_REMOVAL_WKP_EN (1 << 16) +#define INT_CARD_INSERTION_EN (1 << 15) +#define INT_CARD_REMOVAL_EN (1 << 14) +#define INT_SDIO_IRQ_EN (1 << 13) +#define INT_DAT0_EN (1 << 12) +#define INT_BUF_READ_EN (1 << 4) +#define INT_BUF_WRITE_EN (1 << 3) +#define INT_END_CMD_RES_EN (1 << 2) +#define INT_WRITE_OP_DONE_EN (1 << 1) +#define INT_READ_OP_EN (1 << 0) + +struct mxcmci_host { + struct mmc_host *mmc; + struct resource *res; + void __iomem *base; + int irq; + int detect_irq; + int dma; + int do_dma; + unsigned int power_mode; + struct imxmmc_platform_data *pdata; + + struct mmc_request *req; + struct mmc_command *cmd; + struct mmc_data *data; + + unsigned int dma_nents; + unsigned int datasize; + unsigned int dma_dir; + + u16 rev_no; + unsigned int cmdat; + + struct clk *clk; + + int clock; + + struct work_struct datawork; +}; + +static inline int mxcmci_use_dma(struct mxcmci_host *host) +{ + return host->do_dma; +} + +static void mxcmci_softreset(struct mxcmci_host *host) +{ + int i; + + /* reset sequence */ + writew(STR_STP_CLK_RESET, host->base + MMC_REG_STR_STP_CLK); + writew(STR_STP_CLK_RESET | STR_STP_CLK_START_CLK, + host->base + MMC_REG_STR_STP_CLK); + + for (i = 0; i < 8; i++) + writew(STR_STP_CLK_START_CLK, host->base + MMC_REG_STR_STP_CLK); + + writew(0xff, host->base + MMC_REG_RES_TO); +} + +static void mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data) +{ + unsigned int nob = data->blocks; + unsigned int blksz = data->blksz; + unsigned int datasize = nob * blksz; +#ifdef HAS_DMA + struct scatterlist *sg; + int i; +#endif + if (data->flags & MMC_DATA_STREAM) + nob = 0xffff; + + host->data = data; + data->bytes_xfered = 0; + + writew(nob, host->base + MMC_REG_NOB); + writew(blksz, host->base + MMC_REG_BLK_LEN); + host->datasize = datasize; + +#ifdef HAS_DMA + for_each_sg(data->sg, sg, data->sg_len, i) { + if (sg->offset & 3 || sg->length & 3) { + host->do_dma = 0; + return; + } + } + + if (data->flags & MMC_DATA_READ) { + host->dma_dir = DMA_FROM_DEVICE; + host->dma_nents = dma_map_sg(mmc_dev(host->mmc), data->sg, + data->sg_len, host->dma_dir); + + imx_dma_setup_sg(host->dma, data->sg, host->dma_nents, datasize, + host->res->start + MMC_REG_BUFFER_ACCESS, + DMA_MODE_READ); + } else { + host->dma_dir = DMA_TO_DEVICE; + host->dma_nents = dma_map_sg(mmc_dev(host->mmc), data->sg, + data->sg_len, host->dma_dir); + + imx_dma_setup_sg(host->dma, data->sg, host->dma_nents, datasize, + host->res->start + MMC_REG_BUFFER_ACCESS, + DMA_MODE_WRITE); + } + + wmb(); + + imx_dma_enable(host->dma); +#endif /* HAS_DMA */ +} + +static int mxcmci_start_cmd(struct mxcmci_host *host, struct mmc_command *cmd, + unsigned int cmdat) +{ + WARN_ON(host->cmd != NULL); + host->cmd = cmd; + + switch (mmc_resp_type(cmd)) { + case MMC_RSP_R1: /* short CRC, OPCODE */ + case MMC_RSP_R1B:/* short CRC, OPCODE, BUSY */ + cmdat |= CMD_DAT_CONT_RESPONSE_48BIT_CRC; + break; + case MMC_RSP_R2: /* long 136 bit + CRC */ + cmdat |= CMD_DAT_CONT_RESPONSE_136BIT; + break; + case MMC_RSP_R3: /* short */ + cmdat |= CMD_DAT_CONT_RESPONSE_48BIT; + break; + case MMC_RSP_NONE: + break; + default: + dev_err(mmc_dev(host->mmc), "unhandled response type 0x%x\n", + mmc_resp_type(cmd)); + cmd->error = -EINVAL; + return -EINVAL; + } + + if (mxcmci_use_dma(host)) + writel(INT_READ_OP_EN | INT_WRITE_OP_DONE_EN | + INT_END_CMD_RES_EN, + host->base + MMC_REG_INT_CNTR); + else + writel(INT_END_CMD_RES_EN, host->base + MMC_REG_INT_CNTR); + + writew(cmd->opcode, host->base + MMC_REG_CMD); + writel(cmd->arg, host->base + MMC_REG_ARG); + writew(cmdat, host->base + MMC_REG_CMD_DAT_CONT); + + return 0; +} + +static void mxcmci_finish_request(struct mxcmci_host *host, + struct mmc_request *req) +{ + writel(0, host->base + MMC_REG_INT_CNTR); + + host->req = NULL; + host->cmd = NULL; + host->data = NULL; + + mmc_request_done(host->mmc, req); +} + +static int mxcmci_finish_data(struct mxcmci_host *host, unsigned int stat) +{ + struct mmc_data *data = host->data; + int data_error; + +#ifdef HAS_DMA + if (mxcmci_use_dma(host)) { + imx_dma_disable(host->dma); + dma_unmap_sg(mmc_dev(host->mmc), data->sg, host->dma_nents, + host->dma_dir); + } +#endif + + if (stat & STATUS_ERR_MASK) { + dev_dbg(mmc_dev(host->mmc), "request failed. status: 0x%08x\n", + stat); + if (stat & STATUS_CRC_READ_ERR) { + data->error = -EILSEQ; + } else if (stat & STATUS_CRC_WRITE_ERR) { + u32 err_code = (stat >> 9) & 0x3; + if (err_code == 2) /* No CRC response */ + data->error = -ETIMEDOUT; + else + data->error = -EILSEQ; + } else if (stat & STATUS_TIME_OUT_READ) { + data->error = -ETIMEDOUT; + } else { + data->error = -EIO; + } + } else { + data->bytes_xfered = host->datasize; + } + + data_error = data->error; + + host->data = NULL; + + return data_error; +} + +static void mxcmci_read_response(struct mxcmci_host *host, unsigned int stat) +{ + struct mmc_command *cmd = host->cmd; + int i; + u32 a, b, c; + + if (!cmd) + return; + + if (stat & STATUS_TIME_OUT_RESP) { + dev_dbg(mmc_dev(host->mmc), "CMD TIMEOUT\n"); + cmd->error = -ETIMEDOUT; + } else if (stat & STATUS_RESP_CRC_ERR && cmd->flags & MMC_RSP_CRC) { + dev_dbg(mmc_dev(host->mmc), "cmd crc error\n"); + cmd->error = -EILSEQ; + } + + if (cmd->flags & MMC_RSP_PRESENT) { + if (cmd->flags & MMC_RSP_136) { + for (i = 0; i < 4; i++) { + a = readw(host->base + MMC_REG_RES_FIFO); + b = readw(host->base + MMC_REG_RES_FIFO); + cmd->resp[i] = a << 16 | b; + } + } else { + a = readw(host->base + MMC_REG_RES_FIFO); + b = readw(host->base + MMC_REG_RES_FIFO); + c = readw(host->base + MMC_REG_RES_FIFO); + cmd->resp[0] = a << 24 | b << 8 | c >> 8; + } + } +} + +static int mxcmci_poll_status(struct mxcmci_host *host, u32 mask) +{ + u32 stat; + unsigned long timeout = jiffies + HZ; + + do { + stat = readl(host->base + MMC_REG_STATUS); + if (stat & STATUS_ERR_MASK) + return stat; + if (time_after(jiffies, timeout)) + return STATUS_TIME_OUT_READ; + if (stat & mask) + return 0; + cpu_relax(); + } while (1); +} + +static int mxcmci_pull(struct mxcmci_host *host, void *_buf, int bytes) +{ + unsigned int stat; + u32 *buf = _buf; + + while (bytes > 3) { + stat = mxcmci_poll_status(host, + STATUS_BUF_READ_RDY | STATUS_READ_OP_DONE); + if (stat) + return stat; + *buf++ = readl(host->base + MMC_REG_BUFFER_ACCESS); + bytes -= 4; + } + + if (bytes) { + u8 *b = (u8 *)buf; + u32 tmp; + + stat = mxcmci_poll_status(host, + STATUS_BUF_READ_RDY | STATUS_READ_OP_DONE); + if (stat) + return stat; + tmp = readl(host->base + MMC_REG_BUFFER_ACCESS); + memcpy(b, &tmp, bytes); + } + + return 0; +} + +static int mxcmci_push(struct mxcmci_host *host, void *_buf, int bytes) +{ + unsigned int stat; + u32 *buf = _buf; + + while (bytes > 3) { + stat = mxcmci_poll_status(host, STATUS_BUF_WRITE_RDY); + if (stat) + return stat; + writel(*buf++, host->base + MMC_REG_BUFFER_ACCESS); + bytes -= 4; + } + + if (bytes) { + u8 *b = (u8 *)buf; + u32 tmp; + + stat = mxcmci_poll_status(host, STATUS_BUF_WRITE_RDY); + if (stat) + return stat; + + memcpy(&tmp, b, bytes); + writel(tmp, host->base + MMC_REG_BUFFER_ACCESS); + } + + stat = mxcmci_poll_status(host, STATUS_BUF_WRITE_RDY); + if (stat) + return stat; + + return 0; +} + +static int mxcmci_transfer_data(struct mxcmci_host *host) +{ + struct mmc_data *data = host->req->data; + struct scatterlist *sg; + int stat, i; + + host->datasize = 0; + + host->data = data; + host->datasize = 0; + + if (data->flags & MMC_DATA_READ) { + for_each_sg(data->sg, sg, data->sg_len, i) { + stat = mxcmci_pull(host, sg_virt(sg), sg->length); + if (stat) + return stat; + host->datasize += sg->length; + } + } else { + for_each_sg(data->sg, sg, data->sg_len, i) { + stat = mxcmci_push(host, sg_virt(sg), sg->length); + if (stat) + return stat; + host->datasize += sg->length; + } + stat = mxcmci_poll_status(host, STATUS_WRITE_OP_DONE); + if (stat) + return stat; + } + return 0; +} + +static void mxcmci_datawork(struct work_struct *work) +{ + struct mxcmci_host *host = container_of(work, struct mxcmci_host, + datawork); + int datastat = mxcmci_transfer_data(host); + mxcmci_finish_data(host, datastat); + + if (host->req->stop) { + if (mxcmci_start_cmd(host, host->req->stop, 0)) { + mxcmci_finish_request(host, host->req); + return; + } + } else { + mxcmci_finish_request(host, host->req); + } +} + +#ifdef HAS_DMA +static void mxcmci_data_done(struct mxcmci_host *host, unsigned int stat) +{ + struct mmc_data *data = host->data; + int data_error; + + if (!data) + return; + + data_error = mxcmci_finish_data(host, stat); + + mxcmci_read_response(host, stat); + host->cmd = NULL; + + if (host->req->stop) { + if (mxcmci_start_cmd(host, host->req->stop, 0)) { + mxcmci_finish_request(host, host->req); + return; + } + } else { + mxcmci_finish_request(host, host->req); + } +} +#endif /* HAS_DMA */ + +static void mxcmci_cmd_done(struct mxcmci_host *host, unsigned int stat) +{ + mxcmci_read_response(host, stat); + host->cmd = NULL; + + if (!host->data && host->req) { + mxcmci_finish_request(host, host->req); + return; + } + + /* For the DMA case the DMA engine handles the data transfer + * automatically. For non DMA we have to to it ourselves. + * Don't do it in interrupt context though. + */ + if (!mxcmci_use_dma(host) && host->data) + schedule_work(&host->datawork); + +} + +static irqreturn_t mxcmci_irq(int irq, void *devid) +{ + struct mxcmci_host *host = devid; + u32 stat; + + stat = readl(host->base + MMC_REG_STATUS); + writel(stat, host->base + MMC_REG_STATUS); + + dev_dbg(mmc_dev(host->mmc), "%s: 0x%08x\n", __func__, stat); + + if (stat & STATUS_END_CMD_RESP) + mxcmci_cmd_done(host, stat); +#ifdef HAS_DMA + if (mxcmci_use_dma(host) && + (stat & (STATUS_DATA_TRANS_DONE | STATUS_WRITE_OP_DONE))) + mxcmci_data_done(host, stat); +#endif + return IRQ_HANDLED; +} + +static void mxcmci_request(struct mmc_host *mmc, struct mmc_request *req) +{ + struct mxcmci_host *host = mmc_priv(mmc); + unsigned int cmdat = host->cmdat; + + WARN_ON(host->req != NULL); + + host->req = req; + host->cmdat &= ~CMD_DAT_CONT_INIT; +#ifdef HAS_DMA + host->do_dma = 1; +#endif + if (req->data) { + mxcmci_setup_data(host, req->data); + + cmdat |= CMD_DAT_CONT_DATA_ENABLE; + + if (req->data->flags & MMC_DATA_WRITE) + cmdat |= CMD_DAT_CONT_WRITE; + } + + if (mxcmci_start_cmd(host, req->cmd, cmdat)) + mxcmci_finish_request(host, req); +} + +static void mxcmci_set_clk_rate(struct mxcmci_host *host, unsigned int clk_ios) +{ + unsigned int divider; + int prescaler = 0; + unsigned int clk_in = clk_get_rate(host->clk); + + while (prescaler <= 0x800) { + for (divider = 1; divider <= 0xF; divider++) { + int x; + + x = (clk_in / (divider + 1)); + + if (prescaler) + x /= (prescaler * 2); + + if (x <= clk_ios) + break; + } + if (divider < 0x10) + break; + + if (prescaler == 0) + prescaler = 1; + else + prescaler <<= 1; + } + + writew((prescaler << 4) | divider, host->base + MMC_REG_CLK_RATE); + + dev_dbg(mmc_dev(host->mmc), "scaler: %d divider: %d in: %d out: %d\n", + prescaler, divider, clk_in, clk_ios); +} + +static void mxcmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) +{ + struct mxcmci_host *host = mmc_priv(mmc); +#ifdef HAS_DMA + unsigned int blen; + /* + * use burstlen of 64 in 4 bit mode (--> reg value 0) + * use burstlen of 16 in 1 bit mode (--> reg value 16) + */ + if (ios->bus_width == MMC_BUS_WIDTH_4) + blen = 0; + else + blen = 16; + + imx_dma_config_burstlen(host->dma, blen); +#endif + if (ios->bus_width == MMC_BUS_WIDTH_4) + host->cmdat |= CMD_DAT_CONT_BUS_WIDTH_4; + else + host->cmdat &= ~CMD_DAT_CONT_BUS_WIDTH_4; + + if (host->power_mode != ios->power_mode) { + if (host->pdata && host->pdata->setpower) + host->pdata->setpower(mmc_dev(mmc), ios->vdd); + host->power_mode = ios->power_mode; + if (ios->power_mode == MMC_POWER_ON) + host->cmdat |= CMD_DAT_CONT_INIT; + } + + if (ios->clock) { + mxcmci_set_clk_rate(host, ios->clock); + writew(STR_STP_CLK_START_CLK, host->base + MMC_REG_STR_STP_CLK); + } else { + writew(STR_STP_CLK_STOP_CLK, host->base + MMC_REG_STR_STP_CLK); + } + + host->clock = ios->clock; +} + +static irqreturn_t mxcmci_detect_irq(int irq, void *data) +{ + struct mmc_host *mmc = data; + + dev_dbg(mmc_dev(mmc), "%s\n", __func__); + + mmc_detect_change(mmc, msecs_to_jiffies(250)); + return IRQ_HANDLED; +} + +static int mxcmci_get_ro(struct mmc_host *mmc) +{ + struct mxcmci_host *host = mmc_priv(mmc); + + if (host->pdata && host->pdata->get_ro) + return !!host->pdata->get_ro(mmc_dev(mmc)); + /* + * Board doesn't support read only detection; let the mmc core + * decide what to do. + */ + return -ENOSYS; +} + + +static const struct mmc_host_ops mxcmci_ops = { + .request = mxcmci_request, + .set_ios = mxcmci_set_ios, + .get_ro = mxcmci_get_ro, +}; + +static int mxcmci_probe(struct platform_device *pdev) +{ + struct mmc_host *mmc; + struct mxcmci_host *host = NULL; + struct resource *r; + int ret = 0, irq; + + printk(KERN_INFO "i.MX SDHC driver\n"); + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + irq = platform_get_irq(pdev, 0); + if (!r || irq < 0) + return -EINVAL; + + r = request_mem_region(r->start, resource_size(r), pdev->name); + if (!r) + return -EBUSY; + + mmc = mmc_alloc_host(sizeof(struct mxcmci_host), &pdev->dev); + if (!mmc) { + ret = -ENOMEM; + goto out_release_mem; + } + + mmc->ops = &mxcmci_ops; + mmc->caps = MMC_CAP_4_BIT_DATA; + + /* MMC core transfer sizes tunable parameters */ + mmc->max_hw_segs = 64; + mmc->max_phys_segs = 64; + mmc->max_blk_size = 2048; + mmc->max_blk_count = 65535; + mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count; + mmc->max_seg_size = mmc->max_seg_size; + + host = mmc_priv(mmc); + host->base = ioremap(r->start, resource_size(r)); + if (!host->base) { + ret = -ENOMEM; + goto out_free; + } + + host->mmc = mmc; + host->pdata = pdev->dev.platform_data; + + if (host->pdata && host->pdata->ocr_avail) + mmc->ocr_avail = host->pdata->ocr_avail; + else + mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; + + host->res = r; + host->irq = irq; + + host->clk = clk_get(&pdev->dev, "sdhc_clk"); + if (IS_ERR(host->clk)) { + ret = PTR_ERR(host->clk); + goto out_iounmap; + } + clk_enable(host->clk); + + mxcmci_softreset(host); + + host->rev_no = readw(host->base + MMC_REG_REV_NO); + if (host->rev_no != 0x400) { + ret = -ENODEV; + dev_err(mmc_dev(host->mmc), "wrong rev.no. 0x%08x. aborting.\n", + host->rev_no); + goto out_clk_put; + } + + mmc->f_min = clk_get_rate(host->clk) >> 7; + mmc->f_max = clk_get_rate(host->clk) >> 1; + + /* recommended in data sheet */ + writew(0x2db4, host->base + MMC_REG_READ_TO); + + writel(0, host->base + MMC_REG_INT_CNTR); + +#ifdef HAS_DMA + host->dma = imx_dma_request_by_prio(DRIVER_NAME, DMA_PRIO_LOW); + if (host->dma < 0) { + dev_err(mmc_dev(host->mmc), "imx_dma_request_by_prio failed\n"); + ret = -EBUSY; + goto out_clk_put; + } + + r = platform_get_resource(pdev, IORESOURCE_DMA, 0); + if (!r) { + ret = -EINVAL; + goto out_free_dma; + } + + ret = imx_dma_config_channel(host->dma, + IMX_DMA_MEMSIZE_32 | IMX_DMA_TYPE_FIFO, + IMX_DMA_MEMSIZE_32 | IMX_DMA_TYPE_LINEAR, + r->start, 0); + if (ret) { + dev_err(mmc_dev(host->mmc), "failed to config DMA channel\n"); + goto out_free_dma; + } +#endif + INIT_WORK(&host->datawork, mxcmci_datawork); + + ret = request_irq(host->irq, mxcmci_irq, 0, DRIVER_NAME, host); + if (ret) + goto out_free_dma; + + platform_set_drvdata(pdev, mmc); + + if (host->pdata && host->pdata->init) { + ret = host->pdata->init(&pdev->dev, mxcmci_detect_irq, + host->mmc); + if (ret) + goto out_free_irq; + } + + mmc_add_host(mmc); + + return 0; + +out_free_irq: + free_irq(host->irq, host); +out_free_dma: +#ifdef HAS_DMA + imx_dma_free(host->dma); +#endif +out_clk_put: + clk_disable(host->clk); + clk_put(host->clk); +out_iounmap: + iounmap(host->base); +out_free: + mmc_free_host(mmc); +out_release_mem: + release_mem_region(host->res->start, resource_size(host->res)); + return ret; +} + +static int mxcmci_remove(struct platform_device *pdev) +{ + struct mmc_host *mmc = platform_get_drvdata(pdev); + struct mxcmci_host *host = mmc_priv(mmc); + + platform_set_drvdata(pdev, NULL); + + mmc_remove_host(mmc); + + if (host->pdata && host->pdata->exit) + host->pdata->exit(&pdev->dev, mmc); + + free_irq(host->irq, host); + iounmap(host->base); +#ifdef HAS_DMA + imx_dma_free(host->dma); +#endif + clk_disable(host->clk); + clk_put(host->clk); + + release_mem_region(host->res->start, resource_size(host->res)); + release_resource(host->res); + + mmc_free_host(mmc); + + return 0; +} + +#ifdef CONFIG_PM +static int mxcmci_suspend(struct platform_device *dev, pm_message_t state) +{ + struct mmc_host *mmc = platform_get_drvdata(dev); + int ret = 0; + + if (mmc) + ret = mmc_suspend_host(mmc, state); + + return ret; +} + +static int mxcmci_resume(struct platform_device *dev) +{ + struct mmc_host *mmc = platform_get_drvdata(dev); + struct mxcmci_host *host; + int ret = 0; + + if (mmc) { + host = mmc_priv(mmc); + ret = mmc_resume_host(mmc); + } + + return ret; +} +#else +#define mxcmci_suspend NULL +#define mxcmci_resume NULL +#endif /* CONFIG_PM */ + +static struct platform_driver mxcmci_driver = { + .probe = mxcmci_probe, + .remove = mxcmci_remove, + .suspend = mxcmci_suspend, + .resume = mxcmci_resume, + .driver = { + .name = DRIVER_NAME, + .owner = THIS_MODULE, + } +}; + +static int __init mxcmci_init(void) +{ + return platform_driver_register(&mxcmci_driver); +} + +static void __exit mxcmci_exit(void) +{ + platform_driver_unregister(&mxcmci_driver); +} + +module_init(mxcmci_init); +module_exit(mxcmci_exit); + +MODULE_DESCRIPTION("i.MX Multimedia Card Interface Driver"); +MODULE_AUTHOR("Sascha Hauer, Pengutronix"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:imx-mmc"); -- cgit v1.2.3 From cc30d60e4ca0b68e7e3f906eddd1e5b995d349f8 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Sun, 4 Jan 2009 15:18:54 +0100 Subject: mmci: Add support for ST Micro derivate This patch adds support for the ST Microelectronics version of the PL180 PrimeCell. They use designer ID 0x80 and have a few alterations/bugfixes related to open drain and HW flow control. They also add some SDIO registers, I am unsure if these are in ST HW only or if this is things also added in later ARM revisions, but they are included in the mmci.h file for completeness. Signed-off-by: Linus Walleij Signed-off-by: Pierre Ossman --- drivers/mmc/host/mmci.c | 37 +++++++++++++++++++++++++++++++++---- drivers/mmc/host/mmci.h | 28 ++++++++++++++++++++++++++++ 2 files changed, 61 insertions(+), 4 deletions(-) diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c index 1bcbdd6763ac..2909bbc8ad00 100644 --- a/drivers/mmc/host/mmci.c +++ b/drivers/mmc/host/mmci.c @@ -430,6 +430,8 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) clk = 255; host->cclk = host->mclk / (2 * (clk + 1)); } + if (host->hw_designer == 0x80) + clk |= MCI_FCEN; /* Bug fix in ST IP block */ clk |= MCI_CLK_ENABLE; } @@ -440,15 +442,27 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) case MMC_POWER_OFF: break; case MMC_POWER_UP: - pwr |= MCI_PWR_UP; - break; + /* The ST version does not have this, fall through to POWER_ON */ + if (host->hw_designer != 0x80) { + pwr |= MCI_PWR_UP; + break; + } case MMC_POWER_ON: pwr |= MCI_PWR_ON; break; } - if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) - pwr |= MCI_ROD; + if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) { + if (host->hw_designer != 0x80) + pwr |= MCI_ROD; + else { + /* + * The ST Micro variant use the ROD bit for something + * else and only has OD (Open Drain). + */ + pwr |= MCI_OD; + } + } writel(clk, host->base + MMCICLOCK); @@ -500,6 +514,12 @@ static int mmci_probe(struct amba_device *dev, void *id) } host = mmc_priv(mmc); + /* Bits 12 thru 19 is the designer */ + host->hw_designer = (dev->periphid >> 12) & 0xff; + /* Bits 20 thru 23 is the revison */ + host->hw_revision = (dev->periphid >> 20) & 0xf; + DBG(host, "designer ID = 0x%02x\n", host->hw_designer); + DBG(host, "revision = 0x%01x\n", host->hw_revision); host->clk = clk_get(&dev->dev, NULL); if (IS_ERR(host->clk)) { ret = PTR_ERR(host->clk); @@ -693,6 +713,15 @@ static struct amba_id mmci_ids[] = { .id = 0x00041181, .mask = 0x000fffff, }, + /* ST Micro variants */ + { + .id = 0x00180180, + .mask = 0x00ffffff, + }, + { + .id = 0x00280180, + .mask = 0x00ffffff, + }, { 0, 0 }, }; diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h index 0f39c490f022..0441bac1c0ec 100644 --- a/drivers/mmc/host/mmci.h +++ b/drivers/mmc/host/mmci.h @@ -11,13 +11,23 @@ #define MCI_PWR_OFF 0x00 #define MCI_PWR_UP 0x02 #define MCI_PWR_ON 0x03 +#define MCI_DATA2DIREN (1 << 2) +#define MCI_CMDDIREN (1 << 3) +#define MCI_DATA0DIREN (1 << 4) +#define MCI_DATA31DIREN (1 << 5) #define MCI_OD (1 << 6) #define MCI_ROD (1 << 7) +/* The ST Micro version does not have ROD */ +#define MCI_FBCLKEN (1 << 7) +#define MCI_DATA74DIREN (1 << 8) #define MMCICLOCK 0x004 #define MCI_CLK_ENABLE (1 << 8) #define MCI_CLK_PWRSAVE (1 << 9) #define MCI_CLK_BYPASS (1 << 10) +#define MCI_WIDE_BUS (1 << 11) +/* HW flow control on the ST Micro version */ +#define MCI_FCEN (1 << 13) #define MMCIARGUMENT 0x008 #define MMCICOMMAND 0x00c @@ -26,6 +36,10 @@ #define MCI_CPSM_INTERRUPT (1 << 8) #define MCI_CPSM_PENDING (1 << 9) #define MCI_CPSM_ENABLE (1 << 10) +#define MCI_SDIO_SUSP (1 << 11) +#define MCI_ENCMD_COMPL (1 << 12) +#define MCI_NIEN (1 << 13) +#define MCI_CE_ATACMD (1 << 14) #define MMCIRESPCMD 0x010 #define MMCIRESPONSE0 0x014 @@ -39,6 +53,11 @@ #define MCI_DPSM_DIRECTION (1 << 1) #define MCI_DPSM_MODE (1 << 2) #define MCI_DPSM_DMAENABLE (1 << 3) +#define MCI_DPSM_BLOCKSIZE (1 << 4) +#define MCI_DPSM_RWSTART (1 << 8) +#define MCI_DPSM_RWSTOP (1 << 9) +#define MCI_DPSM_RWMOD (1 << 10) +#define MCI_DPSM_SDIOEN (1 << 11) #define MMCIDATACNT 0x030 #define MMCISTATUS 0x034 @@ -63,6 +82,8 @@ #define MCI_RXFIFOEMPTY (1 << 19) #define MCI_TXDATAAVLBL (1 << 20) #define MCI_RXDATAAVLBL (1 << 21) +#define MCI_SDIOIT (1 << 22) +#define MCI_CEATAEND (1 << 23) #define MMCICLEAR 0x038 #define MCI_CMDCRCFAILCLR (1 << 0) @@ -75,6 +96,8 @@ #define MCI_CMDSENTCLR (1 << 7) #define MCI_DATAENDCLR (1 << 8) #define MCI_DATABLOCKENDCLR (1 << 10) +#define MCI_SDIOITC (1 << 22) +#define MCI_CEATAENDC (1 << 23) #define MMCIMASK0 0x03c #define MCI_CMDCRCFAILMASK (1 << 0) @@ -98,6 +121,8 @@ #define MCI_RXFIFOEMPTYMASK (1 << 19) #define MCI_TXDATAAVLBLMASK (1 << 20) #define MCI_RXDATAAVLBLMASK (1 << 21) +#define MCI_SDIOITMASK (1 << 22) +#define MCI_CEATAENDMASK (1 << 23) #define MMCIMASK1 0x040 #define MMCIFIFOCNT 0x048 @@ -136,6 +161,9 @@ struct mmci_host { u32 pwr; struct mmc_platform_data *plat; + u8 hw_designer; + u8 hw_revision:4; + struct timer_list timer; unsigned int oldstat; -- cgit v1.2.3 From 06cc1c880095063fa40b0a640ac0003b43107b40 Mon Sep 17 00:00:00 2001 From: "philipl@overt.org" Date: Sun, 18 Jan 2009 14:11:20 -0500 Subject: ricoh_mmc: Use suspend_late/resume_early If ricoh_mmc suspends before sdhci_pci, it will pull the card out from under the controller, which could leave the system in a very confused state. Using suspend_late/resume_early ensures that sdhci_pci suspends first and resumes second. Signed-off-by: Philip Langdale Signed-off-by: Pierre Ossman --- drivers/mmc/host/ricoh_mmc.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/mmc/host/ricoh_mmc.c b/drivers/mmc/host/ricoh_mmc.c index be9e7b32b34e..f62790513322 100644 --- a/drivers/mmc/host/ricoh_mmc.c +++ b/drivers/mmc/host/ricoh_mmc.c @@ -196,7 +196,7 @@ static void __devexit ricoh_mmc_remove(struct pci_dev *pdev) pci_set_drvdata(pdev, NULL); } -static int ricoh_mmc_suspend(struct pci_dev *pdev, pm_message_t state) +static int ricoh_mmc_suspend_late(struct pci_dev *pdev, pm_message_t state) { struct pci_dev *fw_dev = NULL; @@ -210,7 +210,7 @@ static int ricoh_mmc_suspend(struct pci_dev *pdev, pm_message_t state) return 0; } -static int ricoh_mmc_resume(struct pci_dev *pdev) +static int ricoh_mmc_resume_early(struct pci_dev *pdev) { struct pci_dev *fw_dev = NULL; @@ -229,8 +229,8 @@ static struct pci_driver ricoh_mmc_driver = { .id_table = pci_ids, .probe = ricoh_mmc_probe, .remove = __devexit_p(ricoh_mmc_remove), - .suspend = ricoh_mmc_suspend, - .resume = ricoh_mmc_resume, + .suspend_late = ricoh_mmc_suspend_late, + .resume_early = ricoh_mmc_resume_early, }; /*****************************************************************************\ -- cgit v1.2.3 From e10a854c4602072c34c03380b99da0a3ee15682c Mon Sep 17 00:00:00 2001 From: Cliff Brake Date: Thu, 22 Jan 2009 16:58:58 -0500 Subject: pxamci: replace #ifdef CONFIG_PXA27x with if (cpu_is_pxa27x()) Signed-off-by: Cliff Brake Acked-by: Eric Miao Signed-off-by: Pierre Ossman --- drivers/mmc/host/pxamci.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-) diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c index 3c5483b75da4..3000422f4d81 100644 --- a/drivers/mmc/host/pxamci.c +++ b/drivers/mmc/host/pxamci.c @@ -251,18 +251,17 @@ static int pxamci_cmd_done(struct pxamci_host *host, unsigned int stat) if (stat & STAT_TIME_OUT_RESPONSE) { cmd->error = -ETIMEDOUT; } else if (stat & STAT_RES_CRC_ERR && cmd->flags & MMC_RSP_CRC) { -#ifdef CONFIG_PXA27x /* * workaround for erratum #42: * Intel PXA27x Family Processor Specification Update Rev 001 * A bogus CRC error can appear if the msb of a 136 bit * response is a one. */ - if (cmd->flags & MMC_RSP_136 && cmd->resp[0] & 0x80000000) { + if (cpu_is_pxa27x() && + (cmd->flags & MMC_RSP_136 && cmd->resp[0] & 0x80000000)) pr_debug("ignoring CRC from command %d - *risky*\n", cmd->opcode); - } else -#endif - cmd->error = -EILSEQ; + else + cmd->error = -EILSEQ; } pxamci_disable_irq(host, END_CMD_RES); -- cgit v1.2.3 From b6018958a57f6621d6979c4384e42a3df636beed Mon Sep 17 00:00:00 2001 From: Cliff Brake Date: Thu, 22 Jan 2009 17:07:03 -0500 Subject: pxamci: enable DMA for write ops after CMD/RESP With the PXA270 MMC hardware, there seems to be an issue of data corruption on writes where a 4KB data block is offset by one byte. If we delay enabling the DMA for writes until after the CMD/RESP has finished, the problem seems to be fixed. related to PXA270 Erratum #91 Tested-by: Vernon Sauder Signed-off-by: Cliff Brake Acked-by: Eric Miao Signed-off-by: Pierre Ossman --- drivers/mmc/host/pxamci.c | 16 +++++++++++++++- 1 file changed, 15 insertions(+), 1 deletion(-) diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c index 3000422f4d81..9702ad3774cf 100644 --- a/drivers/mmc/host/pxamci.c +++ b/drivers/mmc/host/pxamci.c @@ -180,7 +180,15 @@ static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data) else DALGN &= ~(1 << host->dma); DDADR(host->dma) = host->sg_dma; - DCSR(host->dma) = DCSR_RUN; + + /* + * workaround for erratum #91: + * only start DMA now if we are doing a read, + * otherwise we wait until CMD/RESP has finished + * before starting DMA. + */ + if (!cpu_is_pxa27x() || data->flags & MMC_DATA_READ) + DCSR(host->dma) = DCSR_RUN; } static void pxamci_start_cmd(struct pxamci_host *host, struct mmc_command *cmd, unsigned int cmdat) @@ -267,6 +275,12 @@ static int pxamci_cmd_done(struct pxamci_host *host, unsigned int stat) pxamci_disable_irq(host, END_CMD_RES); if (host->data && !cmd->error) { pxamci_enable_irq(host, DATA_TRAN_DONE); + /* + * workaround for erratum #91, if doing write + * enable DMA late + */ + if (cpu_is_pxa27x() && host->data->flags & MMC_DATA_WRITE) + DCSR(host->dma) = DCSR_RUN; } else { pxamci_finish_request(host, host->mrq); } -- cgit v1.2.3