From f883199d17b87e86a4ebd50bdee69285814bdce7 Mon Sep 17 00:00:00 2001 From: Xiaolei Li Date: Thu, 2 Nov 2017 10:05:07 +0800 Subject: mtd: nand: mtk: use nand_reset() to reset NAND devices in resume function Previously, we only select chips and then send reset command to a NAND device during resuming nand driver. There is a lack of deselecting chips. It is advised to reset and initialize a NAND device using nand_reset(). Signed-off-by: Xiaolei Li Reviewed-by: Matthias Brugger Signed-off-by: Boris Brezillon --- drivers/mtd/nand/mtk_nand.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-) diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/mtk_nand.c index d86a7d131cc0..6d0101e13ef6 100644 --- a/drivers/mtd/nand/mtk_nand.c +++ b/drivers/mtd/nand/mtk_nand.c @@ -1540,7 +1540,6 @@ static int mtk_nfc_resume(struct device *dev) struct mtk_nfc *nfc = dev_get_drvdata(dev); struct mtk_nfc_nand_chip *chip; struct nand_chip *nand; - struct mtd_info *mtd; int ret; u32 i; @@ -1553,11 +1552,8 @@ static int mtk_nfc_resume(struct device *dev) /* reset NAND chip if VCC was powered off */ list_for_each_entry(chip, &nfc->chips, node) { nand = &chip->nand; - mtd = nand_to_mtd(nand); - for (i = 0; i < chip->nsels; i++) { - nand->select_chip(mtd, i); - nand->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); - } + for (i = 0; i < chip->nsels; i++) + nand_reset(nand, i); } return 0; -- cgit v1.2.3 From b13a9735ae74d4fa9e4d53b4dcfdd779997c8e0e Mon Sep 17 00:00:00 2001 From: "Gustavo A. R. Silva" Date: Fri, 3 Nov 2017 15:31:47 -0500 Subject: mtd: nand: gpmi: replace _manual_ swap with swap macro Make use of the swap macro and remove unnecessary variables swap. This makes the code easier to read and maintain. This code was detected with the help of Coccinelle. Signed-off-by: Gustavo A. R. Silva Acked-by: Han Xu Signed-off-by: Boris Brezillon --- drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 16 ++++------------ 1 file changed, 4 insertions(+), 12 deletions(-) diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c index 50f8d4a1b983..9e365d488b6c 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c @@ -1487,12 +1487,8 @@ static int gpmi_ecc_read_page_raw(struct mtd_info *mtd, * See the layout description for a detailed explanation on why this * is needed. */ - if (this->swap_block_mark) { - u8 swap = tmp_buf[0]; - - tmp_buf[0] = tmp_buf[mtd->writesize]; - tmp_buf[mtd->writesize] = swap; - } + if (this->swap_block_mark) + swap(tmp_buf[0], tmp_buf[mtd->writesize]); /* * Copy the metadata section into the oob buffer (this section is @@ -1615,12 +1611,8 @@ static int gpmi_ecc_write_page_raw(struct mtd_info *mtd, * See the layout description for a detailed explanation on why this * is needed. */ - if (this->swap_block_mark) { - u8 swap = tmp_buf[0]; - - tmp_buf[0] = tmp_buf[mtd->writesize]; - tmp_buf[mtd->writesize] = swap; - } + if (this->swap_block_mark) + swap(tmp_buf[0], tmp_buf[mtd->writesize]); chip->write_buf(mtd, tmp_buf, mtd->writesize + mtd->oobsize); -- cgit v1.2.3 From df467899da0b71465760b4e35127bce837244eee Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Wed, 8 Nov 2017 17:00:27 +0100 Subject: mtd: nand: fix interpretation of NAND_CMD_NONE in nand_command[_lp]() Some drivers (like nand_hynix.c) call ->cmdfunc() with NAND_CMD_NONE and a column address and expect the controller to only send address cycles. Right now, the default ->cmdfunc() implementations provided by the core do not filter out the command cycle in this case and forwards the request to the controller driver through the ->cmd_ctrl() method. The thing is, NAND controller drivers can get this wrong and send a command cycle with a NAND_CMD_NONE opcode and since NAND_CMD_NONE is -1, and the command field is usually casted to an u8, we end up sending the 0xFF command which is actually a RESET operation. Add conditions in nand_command[_lp]() functions to sending the initial command cycle when command == NAND_CMD_NONE. Signed-off-by: Miquel Raynal Signed-off-by: Boris Brezillon --- drivers/mtd/nand/nand_base.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 6135d007a068..630048f5abdc 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -710,7 +710,8 @@ static void nand_command(struct mtd_info *mtd, unsigned int command, chip->cmd_ctrl(mtd, readcmd, ctrl); ctrl &= ~NAND_CTRL_CHANGE; } - chip->cmd_ctrl(mtd, command, ctrl); + if (command != NAND_CMD_NONE) + chip->cmd_ctrl(mtd, command, ctrl); /* Address cycle, when necessary */ ctrl = NAND_CTRL_ALE | NAND_CTRL_CHANGE; @@ -738,6 +739,7 @@ static void nand_command(struct mtd_info *mtd, unsigned int command, */ switch (command) { + case NAND_CMD_NONE: case NAND_CMD_PAGEPROG: case NAND_CMD_ERASE1: case NAND_CMD_ERASE2: @@ -831,7 +833,9 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command, } /* Command latch cycle */ - chip->cmd_ctrl(mtd, command, NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); + if (command != NAND_CMD_NONE) + chip->cmd_ctrl(mtd, command, + NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); if (column != -1 || page_addr != -1) { int ctrl = NAND_CTRL_CHANGE | NAND_NCE | NAND_ALE; @@ -866,6 +870,7 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command, */ switch (command) { + case NAND_CMD_NONE: case NAND_CMD_CACHEDPROG: case NAND_CMD_PAGEPROG: case NAND_CMD_ERASE1: -- cgit v1.2.3 From 26f0740ed6a211bd81edc9118526636e814bd650 Mon Sep 17 00:00:00 2001 From: Boris Brezillon Date: Mon, 13 Nov 2017 10:59:01 +0100 Subject: mtd: nand: hynix: Don't wait after applying new read-retry params Setting read-retry parameters has no impact on the R/B pin, so waiting for the chip to be ready is useless. Signed-off-by: Boris Brezillon --- drivers/mtd/nand/nand_hynix.c | 5 ----- 1 file changed, 5 deletions(-) diff --git a/drivers/mtd/nand/nand_hynix.c b/drivers/mtd/nand/nand_hynix.c index 985751eda317..72d98cbff4ca 100644 --- a/drivers/mtd/nand/nand_hynix.c +++ b/drivers/mtd/nand/nand_hynix.c @@ -83,7 +83,6 @@ static int hynix_nand_setup_read_retry(struct mtd_info *mtd, int retry_mode) struct nand_chip *chip = mtd_to_nand(mtd); struct hynix_nand *hynix = nand_get_manufacturer_data(chip); const u8 *values; - int status; int i; values = hynix->read_retry->values + @@ -112,10 +111,6 @@ static int hynix_nand_setup_read_retry(struct mtd_info *mtd, int retry_mode) /* Apply the new settings. */ chip->cmdfunc(mtd, NAND_HYNIX_CMD_APPLY_PARAMS, -1, -1); - status = chip->waitfunc(mtd, chip); - if (status & NAND_STATUS_FAIL) - return -EIO; - return 0; } -- cgit v1.2.3 From 34832dc44d44d7ea586617d99895e8cfc840be03 Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Fri, 17 Nov 2017 12:09:12 +0100 Subject: mtd: nand: gpmi-nand: Remove wrong Kconfig help text The GPMI nand Kconfig help texts mentions that the GPMI nand driver might conflict with SD cards. The only conflict there might really be is that both controllers use the same pins, but this is resolved by the pincontroller setup in the device tree. In any way the GPMI driver can safely be enabled, the text is just wrong. Remove it. Signed-off-by: Sascha Hauer Reviewed-by: Fabio Estevam Acked-by: Han Xu Signed-off-by: Boris Brezillon --- drivers/mtd/nand/Kconfig | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index bb48aafed9a2..859eb7790c46 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -376,9 +376,7 @@ config MTD_NAND_GPMI_NAND Enables NAND Flash support for IMX23, IMX28 or IMX6. The GPMI controller is very powerful, with the help of BCH module, it can do the hardware ECC. The GPMI supports several - NAND flashs at the same time. The GPMI may conflicts with other - block, such as SD card. So pay attention to it when you enable - the GPMI. + NAND flashs at the same time. config MTD_NAND_BRCMNAND tristate "Broadcom STB NAND controller" -- cgit v1.2.3 From d822401d1c6898a4a4ee03977b78b8cec402e88a Mon Sep 17 00:00:00 2001 From: Jesse Chan Date: Mon, 20 Nov 2017 12:57:13 -0800 Subject: mtd: nand: denali_pci: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE This change resolves a new compile-time warning when built as a loadable module: WARNING: modpost: missing MODULE_LICENSE() in drivers/mtd/nand/denali_pci.o see include/linux/module.h for more information This adds the license as "GPL v2", which matches the header of the file. MODULE_DESCRIPTION and MODULE_AUTHOR are also added. Signed-off-by: Jesse Chan Acked-by: Masahiro Yamada Signed-off-by: Boris Brezillon --- drivers/mtd/nand/denali_pci.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/mtd/nand/denali_pci.c b/drivers/mtd/nand/denali_pci.c index 57fb7ae31412..49cb3e1f8bd0 100644 --- a/drivers/mtd/nand/denali_pci.c +++ b/drivers/mtd/nand/denali_pci.c @@ -125,3 +125,7 @@ static struct pci_driver denali_pci_driver = { .remove = denali_pci_remove, }; module_pci_driver(denali_pci_driver); + +MODULE_DESCRIPTION("PCI driver for Denali NAND controller"); +MODULE_AUTHOR("Intel Corporation and its suppliers"); +MODULE_LICENSE("GPL v2"); -- cgit v1.2.3 From bccb06c353af3764ca86d9da47652458e6c2eb41 Mon Sep 17 00:00:00 2001 From: Jagdish Gediya Date: Thu, 23 Nov 2017 17:04:31 +0530 Subject: mtd: nand: ifc: update bufnum mask for ver >= 2.0.0 Bufnum mask is used to calculate page position in the internal SRAM. As IFC version 2.0.0 has 16KB of internal SRAM as compared to older versions which had 8KB. Hence bufnum mask needs to be updated. Signed-off-by: Jagdish Gediya Signed-off-by: Prabhakar Kushwaha Signed-off-by: Boris Brezillon --- drivers/mtd/nand/fsl_ifc_nand.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c index 9e03bac7f34c..bbdd68a54d68 100644 --- a/drivers/mtd/nand/fsl_ifc_nand.c +++ b/drivers/mtd/nand/fsl_ifc_nand.c @@ -916,6 +916,13 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv) if (ctrl->version >= FSL_IFC_VERSION_1_1_0) fsl_ifc_sram_init(priv); + /* + * As IFC version 2.0.0 has 16KB of internal SRAM as compared to older + * versions which had 8KB. Hence bufnum mask needs to be updated. + */ + if (ctrl->version >= FSL_IFC_VERSION_2_0_0) + priv->bufnum_mask = (priv->bufnum_mask * 2) + 1; + return 0; } -- cgit v1.2.3 From c9e916a4b462104cdd463b8749cf1345f3ad0577 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Thu, 23 Nov 2017 22:18:43 +0900 Subject: mtd: nand: remove unnecessary extern from driver headers 'extern' is not necessary for function declarations. scripts/checkpatch.pl with --strict option reports the following: CHECK: extern prototypes should be avoided in .h files Signed-off-by: Masahiro Yamada Signed-off-by: Boris Brezillon --- drivers/mtd/nand/denali.h | 4 +-- drivers/mtd/nand/gpmi-nand/gpmi-nand.h | 46 +++++++++++++++++----------------- drivers/mtd/nand/sm_common.h | 2 +- 3 files changed, 26 insertions(+), 26 deletions(-) diff --git a/drivers/mtd/nand/denali.h b/drivers/mtd/nand/denali.h index 2911066dacac..9ad33d237378 100644 --- a/drivers/mtd/nand/denali.h +++ b/drivers/mtd/nand/denali.h @@ -329,7 +329,7 @@ struct denali_nand_info { #define DENALI_CAP_DMA_64BIT BIT(1) int denali_calc_ecc_bytes(int step_size, int strength); -extern int denali_init(struct denali_nand_info *denali); -extern void denali_remove(struct denali_nand_info *denali); +int denali_init(struct denali_nand_info *denali); +void denali_remove(struct denali_nand_info *denali); #endif /* __DENALI_H__ */ diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h index a45e4ce13d10..06c1f993912c 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h @@ -268,31 +268,31 @@ struct timing_threshold { }; /* Common Services */ -extern int common_nfc_set_geometry(struct gpmi_nand_data *); -extern struct dma_chan *get_dma_chan(struct gpmi_nand_data *); -extern void prepare_data_dma(struct gpmi_nand_data *, - enum dma_data_direction dr); -extern int start_dma_without_bch_irq(struct gpmi_nand_data *, - struct dma_async_tx_descriptor *); -extern int start_dma_with_bch_irq(struct gpmi_nand_data *, - struct dma_async_tx_descriptor *); +int common_nfc_set_geometry(struct gpmi_nand_data *); +struct dma_chan *get_dma_chan(struct gpmi_nand_data *); +void prepare_data_dma(struct gpmi_nand_data *, + enum dma_data_direction dr); +int start_dma_without_bch_irq(struct gpmi_nand_data *, + struct dma_async_tx_descriptor *); +int start_dma_with_bch_irq(struct gpmi_nand_data *, + struct dma_async_tx_descriptor *); /* GPMI-NAND helper function library */ -extern int gpmi_init(struct gpmi_nand_data *); -extern int gpmi_extra_init(struct gpmi_nand_data *); -extern void gpmi_clear_bch(struct gpmi_nand_data *); -extern void gpmi_dump_info(struct gpmi_nand_data *); -extern int bch_set_geometry(struct gpmi_nand_data *); -extern int gpmi_is_ready(struct gpmi_nand_data *, unsigned chip); -extern int gpmi_send_command(struct gpmi_nand_data *); -extern void gpmi_begin(struct gpmi_nand_data *); -extern void gpmi_end(struct gpmi_nand_data *); -extern int gpmi_read_data(struct gpmi_nand_data *); -extern int gpmi_send_data(struct gpmi_nand_data *); -extern int gpmi_send_page(struct gpmi_nand_data *, - dma_addr_t payload, dma_addr_t auxiliary); -extern int gpmi_read_page(struct gpmi_nand_data *, - dma_addr_t payload, dma_addr_t auxiliary); +int gpmi_init(struct gpmi_nand_data *); +int gpmi_extra_init(struct gpmi_nand_data *); +void gpmi_clear_bch(struct gpmi_nand_data *); +void gpmi_dump_info(struct gpmi_nand_data *); +int bch_set_geometry(struct gpmi_nand_data *); +int gpmi_is_ready(struct gpmi_nand_data *, unsigned chip); +int gpmi_send_command(struct gpmi_nand_data *); +void gpmi_begin(struct gpmi_nand_data *); +void gpmi_end(struct gpmi_nand_data *); +int gpmi_read_data(struct gpmi_nand_data *); +int gpmi_send_data(struct gpmi_nand_data *); +int gpmi_send_page(struct gpmi_nand_data *, + dma_addr_t payload, dma_addr_t auxiliary); +int gpmi_read_page(struct gpmi_nand_data *, + dma_addr_t payload, dma_addr_t auxiliary); void gpmi_copy_bits(u8 *dst, size_t dst_bit_off, const u8 *src, size_t src_bit_off, diff --git a/drivers/mtd/nand/sm_common.h b/drivers/mtd/nand/sm_common.h index d3e028e58b0f..1581671b05ae 100644 --- a/drivers/mtd/nand/sm_common.h +++ b/drivers/mtd/nand/sm_common.h @@ -36,7 +36,7 @@ struct sm_oob { #define SM_SMALL_OOB_SIZE 8 -extern int sm_register_device(struct mtd_info *mtd, int smartmedia); +int sm_register_device(struct mtd_info *mtd, int smartmedia); static inline int sm_sector_valid(struct sm_oob *oob) -- cgit v1.2.3 From 8a8c8ba1c8a65522f07fd3ccbae94712c471e683 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Thu, 23 Nov 2017 22:32:28 +0900 Subject: mtd: nand: denali: rename misleading dma_buf to tmp_buf The "dma_buf" is not used for a DMA bounce buffer, but for arranging the transferred data for the syndrome page layout. In fact, it is used in the PIO mode as well, so "dma_buf" is a misleading name. Rename it to "tmp_buf". Signed-off-by: Masahiro Yamada Signed-off-by: Boris Brezillon --- drivers/mtd/nand/denali.c | 34 +++++++++++++++++----------------- 1 file changed, 17 insertions(+), 17 deletions(-) diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c index 5124f8ae8c04..34008a02ddb0 100644 --- a/drivers/mtd/nand/denali.c +++ b/drivers/mtd/nand/denali.c @@ -710,12 +710,12 @@ static int denali_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, int ecc_steps = chip->ecc.steps; int ecc_size = chip->ecc.size; int ecc_bytes = chip->ecc.bytes; - void *dma_buf = denali->buf; + void *tmp_buf = denali->buf; int oob_skip = denali->oob_skip_bytes; size_t size = writesize + oobsize; int ret, i, pos, len; - ret = denali_data_xfer(denali, dma_buf, size, page, 1, 0); + ret = denali_data_xfer(denali, tmp_buf, size, page, 1, 0); if (ret) return ret; @@ -730,11 +730,11 @@ static int denali_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, else if (pos + len > writesize) len = writesize - pos; - memcpy(buf, dma_buf + pos, len); + memcpy(buf, tmp_buf + pos, len); buf += len; if (len < ecc_size) { len = ecc_size - len; - memcpy(buf, dma_buf + writesize + oob_skip, + memcpy(buf, tmp_buf + writesize + oob_skip, len); buf += len; } @@ -745,7 +745,7 @@ static int denali_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *oob = chip->oob_poi; /* BBM at the beginning of the OOB area */ - memcpy(oob, dma_buf + writesize, oob_skip); + memcpy(oob, tmp_buf + writesize, oob_skip); oob += oob_skip; /* OOB ECC */ @@ -758,11 +758,11 @@ static int denali_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, else if (pos + len > writesize) len = writesize - pos; - memcpy(oob, dma_buf + pos, len); + memcpy(oob, tmp_buf + pos, len); oob += len; if (len < ecc_bytes) { len = ecc_bytes - len; - memcpy(oob, dma_buf + writesize + oob_skip, + memcpy(oob, tmp_buf + writesize + oob_skip, len); oob += len; } @@ -770,7 +770,7 @@ static int denali_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, /* OOB free */ len = oobsize - (oob - chip->oob_poi); - memcpy(oob, dma_buf + size - len, len); + memcpy(oob, tmp_buf + size - len, len); } return 0; @@ -841,7 +841,7 @@ static int denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, int ecc_steps = chip->ecc.steps; int ecc_size = chip->ecc.size; int ecc_bytes = chip->ecc.bytes; - void *dma_buf = denali->buf; + void *tmp_buf = denali->buf; int oob_skip = denali->oob_skip_bytes; size_t size = writesize + oobsize; int i, pos, len; @@ -851,7 +851,7 @@ static int denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, * This simplifies the logic. */ if (!buf || !oob_required) - memset(dma_buf, 0xff, size); + memset(tmp_buf, 0xff, size); /* Arrange the buffer for syndrome payload/ecc layout */ if (buf) { @@ -864,11 +864,11 @@ static int denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, else if (pos + len > writesize) len = writesize - pos; - memcpy(dma_buf + pos, buf, len); + memcpy(tmp_buf + pos, buf, len); buf += len; if (len < ecc_size) { len = ecc_size - len; - memcpy(dma_buf + writesize + oob_skip, buf, + memcpy(tmp_buf + writesize + oob_skip, buf, len); buf += len; } @@ -879,7 +879,7 @@ static int denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *oob = chip->oob_poi; /* BBM at the beginning of the OOB area */ - memcpy(dma_buf + writesize, oob, oob_skip); + memcpy(tmp_buf + writesize, oob, oob_skip); oob += oob_skip; /* OOB ECC */ @@ -892,11 +892,11 @@ static int denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, else if (pos + len > writesize) len = writesize - pos; - memcpy(dma_buf + pos, oob, len); + memcpy(tmp_buf + pos, oob, len); oob += len; if (len < ecc_bytes) { len = ecc_bytes - len; - memcpy(dma_buf + writesize + oob_skip, oob, + memcpy(tmp_buf + writesize + oob_skip, oob, len); oob += len; } @@ -904,10 +904,10 @@ static int denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, /* OOB free */ len = oobsize - (oob - chip->oob_poi); - memcpy(dma_buf + size - len, oob, len); + memcpy(tmp_buf + size - len, oob, len); } - return denali_data_xfer(denali, dma_buf, size, page, 1, 1); + return denali_data_xfer(denali, tmp_buf, size, page, 1, 1); } static int denali_write_page(struct mtd_info *mtd, struct nand_chip *chip, -- cgit v1.2.3 From eb94555e9e97c9983461214046b4d72c4ab4ba70 Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Thu, 30 Nov 2017 18:01:28 +0100 Subject: mtd: nand: use usual return values for the ->erase() hook Avoid using specific defined values for checking returned status of the ->erase() hook. Instead, use usual negative error values on failure, zero otherwise. Signed-off-by: Miquel Raynal Acked-by: Masahiro Yamada Signed-off-by: Boris Brezillon --- drivers/mtd/nand/denali.c | 2 +- drivers/mtd/nand/docg4.c | 7 ++++++- drivers/mtd/nand/nand_base.c | 10 ++++++++-- 3 files changed, 15 insertions(+), 4 deletions(-) diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c index 34008a02ddb0..3e19861a46c6 100644 --- a/drivers/mtd/nand/denali.c +++ b/drivers/mtd/nand/denali.c @@ -951,7 +951,7 @@ static int denali_erase(struct mtd_info *mtd, int page) irq_status = denali_wait_for_irq(denali, INTR__ERASE_COMP | INTR__ERASE_FAIL); - return irq_status & INTR__ERASE_COMP ? 0 : NAND_STATUS_FAIL; + return irq_status & INTR__ERASE_COMP ? 0 : -EIO; } static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr, diff --git a/drivers/mtd/nand/docg4.c b/drivers/mtd/nand/docg4.c index 2436cbc71662..45c01b4b34c7 100644 --- a/drivers/mtd/nand/docg4.c +++ b/drivers/mtd/nand/docg4.c @@ -900,6 +900,7 @@ static int docg4_erase_block(struct mtd_info *mtd, int page) struct docg4_priv *doc = nand_get_controller_data(nand); void __iomem *docptr = doc->virtadr; uint16_t g4_page; + int status; dev_dbg(doc->dev, "%s: page %04x\n", __func__, page); @@ -939,7 +940,11 @@ static int docg4_erase_block(struct mtd_info *mtd, int page) poll_status(doc); write_nop(docptr); - return nand->waitfunc(mtd, nand); + status = nand->waitfunc(mtd, nand); + if (status < 0) + return status; + + return status & NAND_STATUS_FAIL ? -EIO : 0; } static int write_page(struct mtd_info *mtd, struct nand_chip *nand, diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 630048f5abdc..eacc3f39cafd 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -2989,11 +2989,17 @@ out: static int single_erase(struct mtd_info *mtd, int page) { struct nand_chip *chip = mtd_to_nand(mtd); + int status; + /* Send commands to erase a block */ chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); - return chip->waitfunc(mtd, chip); + status = chip->waitfunc(mtd, chip); + if (status < 0) + return status; + + return status & NAND_STATUS_FAIL ? -EIO : 0; } /** @@ -3077,7 +3083,7 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, status = chip->erase(mtd, page & chip->pagemask); /* See if block erase succeeded */ - if (status & NAND_STATUS_FAIL) { + if (status) { pr_debug("%s: failed erase, page 0x%08x\n", __func__, page); instr->state = MTD_ERASE_FAILED; -- cgit v1.2.3 From c18a7ac3398d0cef29749f9568666db8321aa4c9 Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Mon, 6 Nov 2017 11:41:04 +0100 Subject: memory: omap-gpmc: Make 'bank-width' property optional Error out only if both 'bank-width' and 'gpmc,device-width' are missing. As 'bank-width' is mostly used for NOR devices and all other devices must use 'gpmc,device-width' update the error message accordingly. Signed-off-by: Ladislav Michl Signed-off-by: Roger Quadros --- drivers/memory/omap-gpmc.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/memory/omap-gpmc.c b/drivers/memory/omap-gpmc.c index a385a35c7de9..0e30ee1c8677 100644 --- a/drivers/memory/omap-gpmc.c +++ b/drivers/memory/omap-gpmc.c @@ -2077,8 +2077,9 @@ static int gpmc_probe_generic_child(struct platform_device *pdev, } else { ret = of_property_read_u32(child, "bank-width", &gpmc_s.device_width); - if (ret < 0) { - dev_err(&pdev->dev, "%pOF has no 'bank-width' property\n", + if (ret < 0 && !gpmc_s.device_width) { + dev_err(&pdev->dev, + "%pOF has no 'gpmc,device-width' property\n", child); goto err; } -- cgit v1.2.3 From 97d90da8a886949f09bb4754843fb0b504956ad2 Mon Sep 17 00:00:00 2001 From: Boris Brezillon Date: Thu, 30 Nov 2017 18:01:29 +0100 Subject: mtd: nand: provide several helpers to do common NAND operations This is part of the process of removing direct calls to ->cmdfunc() outside of the core in order to introduce a better interface to execute NAND operations. Here we provide several helpers and make use of them to remove all direct calls to ->cmdfunc(). This way, we can easily modify those helpers to make use of the new ->exec_op() interface when available. Signed-off-by: Boris Brezillon [miquel.raynal@free-electrons.com: rebased and fixed some conflicts] Signed-off-by: Miquel Raynal Acked-by: Masahiro Yamada --- drivers/mtd/nand/atmel/nand-controller.c | 2 +- drivers/mtd/nand/brcmnand/brcmnand.c | 9 +- drivers/mtd/nand/cafe_nand.c | 14 +- drivers/mtd/nand/denali.c | 37 +- drivers/mtd/nand/diskonchip.c | 4 +- drivers/mtd/nand/docg4.c | 2 +- drivers/mtd/nand/fsmc_nand.c | 5 +- drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 58 +- drivers/mtd/nand/hisi504_nand.c | 3 +- drivers/mtd/nand/jz4740_nand.c | 16 +- drivers/mtd/nand/lpc32xx_mlc.c | 2 +- drivers/mtd/nand/lpc32xx_slc.c | 22 +- drivers/mtd/nand/mtk_nand.c | 11 +- drivers/mtd/nand/nand_base.c | 1011 +++++++++++++++++++++++++----- drivers/mtd/nand/nand_hynix.c | 115 ++-- drivers/mtd/nand/nand_micron.c | 77 ++- drivers/mtd/nand/omap2.c | 8 +- drivers/mtd/nand/pxa3xx_nand.c | 8 +- drivers/mtd/nand/qcom_nandc.c | 16 +- drivers/mtd/nand/r852.c | 11 +- drivers/mtd/nand/sunxi_nand.c | 71 +-- drivers/mtd/nand/tango_nand.c | 26 +- drivers/mtd/nand/tmio_nand.c | 5 +- include/linux/mtd/rawnand.h | 29 + 24 files changed, 1131 insertions(+), 431 deletions(-) diff --git a/drivers/mtd/nand/atmel/nand-controller.c b/drivers/mtd/nand/atmel/nand-controller.c index 90a71a56bc23..e81fdd2d47b1 100644 --- a/drivers/mtd/nand/atmel/nand-controller.c +++ b/drivers/mtd/nand/atmel/nand-controller.c @@ -1000,7 +1000,7 @@ static int atmel_hsmc_nand_pmecc_read_pg(struct nand_chip *chip, u8 *buf, * to the non-optimized one. */ if (nand->activecs->rb.type != ATMEL_NAND_NATIVE_RB) { - chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page); + nand_read_page_op(chip, page, 0, NULL, 0); return atmel_nand_pmecc_read_pg(chip, buf, oob_required, page, raw); diff --git a/drivers/mtd/nand/brcmnand/brcmnand.c b/drivers/mtd/nand/brcmnand/brcmnand.c index e0eb51d8c012..3f441096a14c 100644 --- a/drivers/mtd/nand/brcmnand/brcmnand.c +++ b/drivers/mtd/nand/brcmnand/brcmnand.c @@ -1071,7 +1071,7 @@ static void brcmnand_wp(struct mtd_info *mtd, int wp) return; brcmnand_set_wp(ctrl, wp); - chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); + nand_status_op(chip, NULL); /* NAND_STATUS_WP 0x00 = protected, 0x80 = not protected */ ret = bcmnand_ctrl_poll_status(ctrl, NAND_CTRL_RDY | @@ -1453,7 +1453,7 @@ static uint8_t brcmnand_read_byte(struct mtd_info *mtd) /* At FC_BYTES boundary, switch to next column */ if (host->last_byte > 0 && offs == 0) - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, addr, -1); + nand_change_read_column_op(chip, addr, NULL, 0, false); ret = ctrl->flash_cache[offs]; break; @@ -1689,7 +1689,7 @@ static int brcmstb_nand_verify_erased_page(struct mtd_info *mtd, sas = mtd->oobsize / chip->ecc.steps; /* read without ecc for verification */ - chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page); + nand_read_page_op(chip, page, 0, NULL, 0); ret = chip->ecc.read_page_raw(mtd, chip, buf, true, page); if (ret) return ret; @@ -2369,12 +2369,11 @@ static int brcmnand_resume(struct device *dev) list_for_each_entry(host, &ctrl->host_list, node) { struct nand_chip *chip = &host->chip; - struct mtd_info *mtd = nand_to_mtd(chip); brcmnand_save_restore_cs_config(host, 1); /* Reset the chip, required by some chips after power-up */ - chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + nand_reset_op(chip); } return 0; diff --git a/drivers/mtd/nand/cafe_nand.c b/drivers/mtd/nand/cafe_nand.c index bc558c438a57..95c2cfa68b66 100644 --- a/drivers/mtd/nand/cafe_nand.c +++ b/drivers/mtd/nand/cafe_nand.c @@ -353,23 +353,15 @@ static void cafe_nand_bug(struct mtd_info *mtd) static int cafe_nand_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { - int status = 0; - - chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page); - chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - status = chip->waitfunc(mtd, chip); - - return status & NAND_STATUS_FAIL ? -EIO : 0; + return nand_prog_page_op(chip, page, mtd->writesize, chip->oob_poi, + mtd->oobsize); } /* Don't use -- use nand_read_oob_std for now */ static int cafe_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { - chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); - chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + return nand_read_oob_op(chip, page, 0, chip->oob_poi, mtd->oobsize); } /** * cafe_nand_read_page_syndrome - [REPLACEABLE] hardware ecc syndrome based page read diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c index 3e19861a46c6..d5c80d617854 100644 --- a/drivers/mtd/nand/denali.c +++ b/drivers/mtd/nand/denali.c @@ -645,8 +645,6 @@ static void denali_oob_xfer(struct mtd_info *mtd, struct nand_chip *chip, int page, int write) { struct denali_nand_info *denali = mtd_to_denali(mtd); - unsigned int start_cmd = write ? NAND_CMD_SEQIN : NAND_CMD_READ0; - unsigned int rnd_cmd = write ? NAND_CMD_RNDIN : NAND_CMD_RNDOUT; int writesize = mtd->writesize; int oobsize = mtd->oobsize; uint8_t *bufpoi = chip->oob_poi; @@ -658,11 +656,11 @@ static void denali_oob_xfer(struct mtd_info *mtd, struct nand_chip *chip, int i, pos, len; /* BBM at the beginning of the OOB area */ - chip->cmdfunc(mtd, start_cmd, writesize, page); if (write) - chip->write_buf(mtd, bufpoi, oob_skip); + nand_prog_page_begin_op(chip, page, writesize, bufpoi, + oob_skip); else - chip->read_buf(mtd, bufpoi, oob_skip); + nand_read_page_op(chip, page, writesize, bufpoi, oob_skip); bufpoi += oob_skip; /* OOB ECC */ @@ -675,30 +673,35 @@ static void denali_oob_xfer(struct mtd_info *mtd, struct nand_chip *chip, else if (pos + len > writesize) len = writesize - pos; - chip->cmdfunc(mtd, rnd_cmd, pos, -1); if (write) - chip->write_buf(mtd, bufpoi, len); + nand_change_write_column_op(chip, pos, bufpoi, len, + false); else - chip->read_buf(mtd, bufpoi, len); + nand_change_read_column_op(chip, pos, bufpoi, len, + false); bufpoi += len; if (len < ecc_bytes) { len = ecc_bytes - len; - chip->cmdfunc(mtd, rnd_cmd, writesize + oob_skip, -1); if (write) - chip->write_buf(mtd, bufpoi, len); + nand_change_write_column_op(chip, writesize + + oob_skip, bufpoi, + len, false); else - chip->read_buf(mtd, bufpoi, len); + nand_change_read_column_op(chip, writesize + + oob_skip, bufpoi, + len, false); bufpoi += len; } } /* OOB free */ len = oobsize - (bufpoi - chip->oob_poi); - chip->cmdfunc(mtd, rnd_cmd, size - len, -1); if (write) - chip->write_buf(mtd, bufpoi, len); + nand_change_write_column_op(chip, size - len, bufpoi, len, + false); else - chip->read_buf(mtd, bufpoi, len); + nand_change_read_column_op(chip, size - len, bufpoi, len, + false); } static int denali_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, @@ -788,16 +791,12 @@ static int denali_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { struct denali_nand_info *denali = mtd_to_denali(mtd); - int status; denali_reset_irq(denali); denali_oob_xfer(mtd, chip, page, 1); - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - status = chip->waitfunc(mtd, chip); - - return status & NAND_STATUS_FAIL ? -EIO : 0; + return nand_prog_page_end_op(chip); } static int denali_read_page(struct mtd_info *mtd, struct nand_chip *chip, diff --git a/drivers/mtd/nand/diskonchip.c b/drivers/mtd/nand/diskonchip.c index 72671dc52e2e..6bc93ea66f50 100644 --- a/drivers/mtd/nand/diskonchip.c +++ b/drivers/mtd/nand/diskonchip.c @@ -448,7 +448,7 @@ static int doc200x_wait(struct mtd_info *mtd, struct nand_chip *this) int status; DoC_WaitReady(doc); - this->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); + nand_status_op(this, NULL); DoC_WaitReady(doc); status = (int)this->read_byte(mtd); @@ -595,7 +595,7 @@ static void doc2001plus_select_chip(struct mtd_info *mtd, int chip) /* Assert ChipEnable and deassert WriteProtect */ WriteDOC((DOC_FLASH_CE), docptr, Mplus_FlashSelect); - this->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + nand_reset_op(this); doc->curchip = chip; doc->curfloor = floor; diff --git a/drivers/mtd/nand/docg4.c b/drivers/mtd/nand/docg4.c index 45c01b4b34c7..5a27f56dafdc 100644 --- a/drivers/mtd/nand/docg4.c +++ b/drivers/mtd/nand/docg4.c @@ -864,7 +864,7 @@ static int docg4_read_oob(struct mtd_info *mtd, struct nand_chip *nand, dev_dbg(doc->dev, "%s: page %x\n", __func__, page); - docg4_command(mtd, NAND_CMD_READ0, nand->ecc.size, page); + nand_read_page_op(nand, page, nand->ecc.size, NULL, 0); writew(DOC_ECCCONF0_READ_MODE | DOCG4_OOB_SIZE, docptr + DOC_ECCCONF0); write_nop(docptr); diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c index eac15d9bf49e..b44e5c6545e0 100644 --- a/drivers/mtd/nand/fsmc_nand.c +++ b/drivers/mtd/nand/fsmc_nand.c @@ -697,7 +697,7 @@ static int fsmc_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, unsigned int max_bitflips = 0; for (i = 0, s = 0; s < eccsteps; s++, i += eccbytes, p += eccsize) { - chip->cmdfunc(mtd, NAND_CMD_READ0, s * eccsize, page); + nand_read_page_op(chip, page, s * eccsize, NULL, 0); chip->ecc.hwctl(mtd, NAND_ECC_READ); chip->read_buf(mtd, p, eccsize); @@ -720,8 +720,7 @@ static int fsmc_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, if (chip->options & NAND_BUSWIDTH_16) len = roundup(len, 2); - chip->cmdfunc(mtd, NAND_CMD_READOOB, off, page); - chip->read_buf(mtd, oob + j, len); + nand_read_oob_op(chip, page, off, oob + j, len); j += len; } diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c index 9e365d488b6c..63a425ced4cd 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c @@ -1097,8 +1097,8 @@ static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip, eccbytes = DIV_ROUND_UP(offset + eccbits, 8); offset /= 8; eccbytes -= offset; - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, offset, -1); - chip->read_buf(mtd, eccbuf, eccbytes); + nand_change_read_column_op(chip, offset, eccbuf, + eccbytes, false); /* * ECC data are not byte aligned and we may have @@ -1220,7 +1220,7 @@ static int gpmi_ecc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, meta = geo->metadata_size; if (first) { col = meta + (size + ecc_parity_size) * first; - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, col, -1); + nand_change_read_column_op(chip, col, NULL, 0, false); meta = 0; buf = buf + first * size; @@ -1411,7 +1411,7 @@ static int gpmi_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *chip, memset(chip->oob_poi, ~0, mtd->oobsize); /* Read out the conventional OOB. */ - chip->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page); + nand_read_page_op(chip, page, mtd->writesize, NULL, 0); chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); /* @@ -1421,7 +1421,7 @@ static int gpmi_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *chip, */ if (GPMI_IS_MX23(this)) { /* Read the block mark into the first byte of the OOB buffer. */ - chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + nand_read_page_op(chip, page, 0, NULL, 0); chip->oob_poi[0] = chip->read_byte(mtd); } @@ -1432,7 +1432,6 @@ static int gpmi_ecc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { struct mtd_oob_region of = { }; - int status = 0; /* Do we have available oob area? */ mtd_ooblayout_free(mtd, 0, &of); @@ -1442,12 +1441,8 @@ gpmi_ecc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) if (!nand_is_slc(chip)) return -EPERM; - chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize + of.offset, page); - chip->write_buf(mtd, chip->oob_poi + of.offset, of.length); - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - - status = chip->waitfunc(mtd, chip); - return status & NAND_STATUS_FAIL ? -EIO : 0; + return nand_prog_page_op(chip, page, mtd->writesize + of.offset, + chip->oob_poi + of.offset, of.length); } /* @@ -1622,7 +1617,7 @@ static int gpmi_ecc_write_page_raw(struct mtd_info *mtd, static int gpmi_ecc_read_oob_raw(struct mtd_info *mtd, struct nand_chip *chip, int page) { - chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + nand_read_page_op(chip, page, 0, NULL, 0); return gpmi_ecc_read_page_raw(mtd, chip, NULL, 1, page); } @@ -1630,7 +1625,7 @@ static int gpmi_ecc_read_oob_raw(struct mtd_info *mtd, struct nand_chip *chip, static int gpmi_ecc_write_oob_raw(struct mtd_info *mtd, struct nand_chip *chip, int page) { - chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0, page); + nand_prog_page_begin_op(chip, page, 0, NULL, 0); return gpmi_ecc_write_page_raw(mtd, chip, NULL, 1, page); } @@ -1641,7 +1636,7 @@ static int gpmi_block_markbad(struct mtd_info *mtd, loff_t ofs) struct gpmi_nand_data *this = nand_get_controller_data(chip); int ret = 0; uint8_t *block_mark; - int column, page, status, chipnr; + int column, page, chipnr; chipnr = (int)(ofs >> chip->chip_shift); chip->select_chip(mtd, chipnr); @@ -1655,13 +1650,7 @@ static int gpmi_block_markbad(struct mtd_info *mtd, loff_t ofs) /* Shift to get page */ page = (int)(ofs >> chip->page_shift); - chip->cmdfunc(mtd, NAND_CMD_SEQIN, column, page); - chip->write_buf(mtd, block_mark, 1); - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - - status = chip->waitfunc(mtd, chip); - if (status & NAND_STATUS_FAIL) - ret = -EIO; + ret = nand_prog_page_op(chip, page, column, block_mark, 1); chip->select_chip(mtd, -1); @@ -1729,7 +1718,7 @@ static int mx23_check_transcription_stamp(struct gpmi_nand_data *this) * Read the NCB fingerprint. The fingerprint is four bytes long * and starts in the 12th byte of the page. */ - chip->cmdfunc(mtd, NAND_CMD_READ0, 12, page); + nand_read_page_op(chip, page, 12, NULL, 0); chip->read_buf(mtd, buffer, strlen(fingerprint)); /* Look for the fingerprint. */ @@ -1789,17 +1778,10 @@ static int mx23_write_transcription_stamp(struct gpmi_nand_data *this) dev_dbg(dev, "Erasing the search area...\n"); for (block = 0; block < search_area_size_in_blocks; block++) { - /* Compute the page address. */ - page = block * block_size_in_pages; - /* Erase this block. */ dev_dbg(dev, "\tErasing block 0x%x\n", block); - chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); - chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); - - /* Wait for the erase to finish. */ - status = chip->waitfunc(mtd, chip); - if (status & NAND_STATUS_FAIL) + status = nand_erase_op(chip, block); + if (status) dev_err(dev, "[%s] Erase failed.\n", __func__); } @@ -1815,13 +1797,11 @@ static int mx23_write_transcription_stamp(struct gpmi_nand_data *this) /* Write the first page of the current stride. */ dev_dbg(dev, "Writing an NCB fingerprint in page 0x%x\n", page); - chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page); - chip->ecc.write_page_raw(mtd, chip, buffer, 0, page); - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - /* Wait for the write to finish. */ - status = chip->waitfunc(mtd, chip); - if (status & NAND_STATUS_FAIL) + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + chip->ecc.write_page_raw(mtd, chip, buffer, 0, page); + status = nand_prog_page_end_op(chip); + if (status) dev_err(dev, "[%s] Write failed.\n", __func__); } @@ -1876,7 +1856,7 @@ static int mx23_boot_init(struct gpmi_nand_data *this) /* Send the command to read the conventional block mark. */ chip->select_chip(mtd, chipnr); - chip->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page); + nand_read_page_op(chip, page, mtd->writesize, NULL, 0); block_mark = chip->read_byte(mtd); chip->select_chip(mtd, -1); diff --git a/drivers/mtd/nand/hisi504_nand.c b/drivers/mtd/nand/hisi504_nand.c index 0897261c3e17..184d765c8bbe 100644 --- a/drivers/mtd/nand/hisi504_nand.c +++ b/drivers/mtd/nand/hisi504_nand.c @@ -574,8 +574,7 @@ static int hisi_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip, { struct hinfc_host *host = nand_get_controller_data(chip); - chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); - chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + nand_read_oob_op(chip, page, 0, chip->oob_poi, mtd->oobsize); if (host->irq_status & HINFC504_INTS_UE) { host->irq_status = 0; diff --git a/drivers/mtd/nand/jz4740_nand.c b/drivers/mtd/nand/jz4740_nand.c index ad827d4af3e9..613b00a9604b 100644 --- a/drivers/mtd/nand/jz4740_nand.c +++ b/drivers/mtd/nand/jz4740_nand.c @@ -313,6 +313,7 @@ static int jz_nand_detect_bank(struct platform_device *pdev, uint32_t ctrl; struct nand_chip *chip = &nand->chip; struct mtd_info *mtd = nand_to_mtd(chip); + u8 id[2]; /* Request I/O resource. */ sprintf(res_name, "bank%d", bank); @@ -335,17 +336,16 @@ static int jz_nand_detect_bank(struct platform_device *pdev, /* Retrieve the IDs from the first chip. */ chip->select_chip(mtd, 0); - chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); - chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); - *nand_maf_id = chip->read_byte(mtd); - *nand_dev_id = chip->read_byte(mtd); + nand_reset_op(chip); + nand_readid_op(chip, 0, id, sizeof(id)); + *nand_maf_id = id[0]; + *nand_dev_id = id[1]; } else { /* Detect additional chip. */ chip->select_chip(mtd, chipnr); - chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); - chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); - if (*nand_maf_id != chip->read_byte(mtd) - || *nand_dev_id != chip->read_byte(mtd)) { + nand_reset_op(chip); + nand_readid_op(chip, 0, id, sizeof(id)); + if (*nand_maf_id != id[0] || *nand_dev_id != id[1]) { ret = -ENODEV; goto notfound_id; } diff --git a/drivers/mtd/nand/lpc32xx_mlc.c b/drivers/mtd/nand/lpc32xx_mlc.c index 5796468db653..31cb3b2967b9 100644 --- a/drivers/mtd/nand/lpc32xx_mlc.c +++ b/drivers/mtd/nand/lpc32xx_mlc.c @@ -461,7 +461,7 @@ static int lpc32xx_read_page(struct mtd_info *mtd, struct nand_chip *chip, } /* Writing Command and Address */ - chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + nand_read_page_op(chip, page, 0, NULL, 0); /* For all sub-pages */ for (i = 0; i < host->mlcsubpages; i++) { diff --git a/drivers/mtd/nand/lpc32xx_slc.c b/drivers/mtd/nand/lpc32xx_slc.c index b61f28a1554d..2b96c281b1a2 100644 --- a/drivers/mtd/nand/lpc32xx_slc.c +++ b/drivers/mtd/nand/lpc32xx_slc.c @@ -399,10 +399,7 @@ static void lpc32xx_nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int static int lpc32xx_nand_read_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip, int page) { - chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); - chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); - - return 0; + return nand_read_oob_op(chip, page, 0, chip->oob_poi, mtd->oobsize); } /* @@ -411,17 +408,8 @@ static int lpc32xx_nand_read_oob_syndrome(struct mtd_info *mtd, static int lpc32xx_nand_write_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip, int page) { - int status; - - chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page); - chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); - - /* Send command to program the OOB data */ - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - - status = chip->waitfunc(mtd, chip); - - return status & NAND_STATUS_FAIL ? -EIO : 0; + return nand_prog_page_op(chip, page, mtd->writesize, chip->oob_poi, + mtd->oobsize); } /* @@ -632,7 +620,7 @@ static int lpc32xx_nand_read_page_syndrome(struct mtd_info *mtd, uint8_t *oobecc, tmpecc[LPC32XX_ECC_SAVE_SIZE]; /* Issue read command */ - chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + nand_read_page_op(chip, page, 0, NULL, 0); /* Read data and oob, calculate ECC */ status = lpc32xx_xfer(mtd, buf, chip->ecc.steps, 1); @@ -675,7 +663,7 @@ static int lpc32xx_nand_read_page_raw_syndrome(struct mtd_info *mtd, int page) { /* Issue read command */ - chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + nand_read_page_op(chip, page, 0, NULL, 0); /* Raw reads can just use the FIFO interface */ chip->read_buf(mtd, buf, chip->ecc.size * chip->ecc.steps); diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/mtk_nand.c index 6d0101e13ef6..9c4adaf9331b 100644 --- a/drivers/mtd/nand/mtk_nand.c +++ b/drivers/mtd/nand/mtk_nand.c @@ -834,16 +834,13 @@ static int mtk_nfc_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip, { int ret; - chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page); + nand_prog_page_begin_op(chip, page, 0, NULL, 0); ret = mtk_nfc_write_page_raw(mtd, chip, NULL, 1, page); if (ret < 0) return -EIO; - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - ret = chip->waitfunc(mtd, chip); - - return ret & NAND_STATUS_FAIL ? -EIO : 0; + return nand_prog_page_end_op(chip); } static int mtk_nfc_update_ecc_stats(struct mtd_info *mtd, u8 *buf, u32 sectors) @@ -893,7 +890,7 @@ static int mtk_nfc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, buf = bufpoi + start * chip->ecc.size; if (column != 0) - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, column, -1); + nand_change_read_column_op(chip, column, NULL, 0, false); addr = dma_map_single(nfc->dev, buf, len, DMA_FROM_DEVICE); rc = dma_mapping_error(nfc->dev, addr); @@ -1016,7 +1013,7 @@ static int mtk_nfc_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, static int mtk_nfc_read_oob_std(struct mtd_info *mtd, struct nand_chip *chip, int page) { - chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + nand_read_page_op(chip, page, 0, NULL, 0); return mtk_nfc_read_page_raw(mtd, chip, NULL, 1, page); } diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index eacc3f39cafd..539132ef0095 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -561,14 +561,19 @@ static int nand_block_markbad_lowlevel(struct mtd_info *mtd, loff_t ofs) static int nand_check_wp(struct mtd_info *mtd) { struct nand_chip *chip = mtd_to_nand(mtd); + u8 status; + int ret; /* Broken xD cards report WP despite being writable */ if (chip->options & NAND_BROKEN_XD) return 0; /* Check the WP bit */ - chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); - return (chip->read_byte(mtd) & NAND_STATUS_WP) ? 0 : 1; + ret = nand_status_op(chip, &status); + if (ret) + return ret; + + return status & NAND_STATUS_WP ? 0 : 1; } /** @@ -667,10 +672,17 @@ EXPORT_SYMBOL_GPL(nand_wait_ready); static void nand_wait_status_ready(struct mtd_info *mtd, unsigned long timeo) { register struct nand_chip *chip = mtd_to_nand(mtd); + int ret; timeo = jiffies + msecs_to_jiffies(timeo); do { - if ((chip->read_byte(mtd) & NAND_STATUS_READY)) + u8 status; + + ret = nand_read_data_op(chip, &status, sizeof(status), true); + if (ret) + return; + + if (status & NAND_STATUS_READY) break; touch_softlockup_watchdog(); } while (time_before(jiffies, timeo)); @@ -1019,7 +1031,15 @@ static void panic_nand_wait(struct mtd_info *mtd, struct nand_chip *chip, if (chip->dev_ready(mtd)) break; } else { - if (chip->read_byte(mtd) & NAND_STATUS_READY) + int ret; + u8 status; + + ret = nand_read_data_op(chip, &status, sizeof(status), + true); + if (ret) + return; + + if (status & NAND_STATUS_READY) break; } mdelay(1); @@ -1036,8 +1056,9 @@ static void panic_nand_wait(struct mtd_info *mtd, struct nand_chip *chip, static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip) { - int status; unsigned long timeo = 400; + u8 status; + int ret; /* * Apply this short delay always to ensure that we do wait tWB in any @@ -1045,7 +1066,9 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip) */ ndelay(100); - chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); + ret = nand_status_op(chip, NULL); + if (ret) + return ret; if (in_interrupt() || oops_in_progress) panic_nand_wait(mtd, chip, timeo); @@ -1056,14 +1079,22 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip) if (chip->dev_ready(mtd)) break; } else { - if (chip->read_byte(mtd) & NAND_STATUS_READY) + ret = nand_read_data_op(chip, &status, + sizeof(status), true); + if (ret) + return ret; + + if (status & NAND_STATUS_READY) break; } cond_resched(); } while (time_before(jiffies, timeo)); } - status = (int)chip->read_byte(mtd); + ret = nand_read_data_op(chip, &status, sizeof(status), true); + if (ret) + return ret; + /* This can happen if in case of timeout or buggy dev_ready */ WARN_ON(!(status & NAND_STATUS_READY)); return status; @@ -1217,6 +1248,516 @@ static void nand_release_data_interface(struct nand_chip *chip) kfree(chip->data_interface); } +/** + * nand_read_page_op - Do a READ PAGE operation + * @chip: The NAND chip + * @page: page to read + * @offset_in_page: offset within the page + * @buf: buffer used to store the data + * @len: length of the buffer + * + * This function issues a READ PAGE operation. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_read_page_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, void *buf, unsigned int len) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + if (len && !buf) + return -EINVAL; + + if (offset_in_page + len > mtd->writesize + mtd->oobsize) + return -EINVAL; + + chip->cmdfunc(mtd, NAND_CMD_READ0, offset_in_page, page); + if (len) + chip->read_buf(mtd, buf, len); + + return 0; +} +EXPORT_SYMBOL_GPL(nand_read_page_op); + +/** + * nand_read_param_page_op - Do a READ PARAMETER PAGE operation + * @chip: The NAND chip + * @page: parameter page to read + * @buf: buffer used to store the data + * @len: length of the buffer + * + * This function issues a READ PARAMETER PAGE operation. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +static int nand_read_param_page_op(struct nand_chip *chip, u8 page, void *buf, + unsigned int len) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + unsigned int i; + u8 *p = buf; + + if (len && !buf) + return -EINVAL; + + chip->cmdfunc(mtd, NAND_CMD_PARAM, page, -1); + for (i = 0; i < len; i++) + p[i] = chip->read_byte(mtd); + + return 0; +} + +/** + * nand_change_read_column_op - Do a CHANGE READ COLUMN operation + * @chip: The NAND chip + * @offset_in_page: offset within the page + * @buf: buffer used to store the data + * @len: length of the buffer + * @force_8bit: force 8-bit bus access + * + * This function issues a CHANGE READ COLUMN operation. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_change_read_column_op(struct nand_chip *chip, + unsigned int offset_in_page, void *buf, + unsigned int len, bool force_8bit) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + if (len && !buf) + return -EINVAL; + + if (offset_in_page + len > mtd->writesize + mtd->oobsize) + return -EINVAL; + + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, offset_in_page, -1); + if (len) + chip->read_buf(mtd, buf, len); + + return 0; +} +EXPORT_SYMBOL_GPL(nand_change_read_column_op); + +/** + * nand_read_oob_op - Do a READ OOB operation + * @chip: The NAND chip + * @page: page to read + * @offset_in_oob: offset within the OOB area + * @buf: buffer used to store the data + * @len: length of the buffer + * + * This function issues a READ OOB operation. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_read_oob_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_oob, void *buf, unsigned int len) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + if (len && !buf) + return -EINVAL; + + if (offset_in_oob + len > mtd->oobsize) + return -EINVAL; + + chip->cmdfunc(mtd, NAND_CMD_READOOB, offset_in_oob, page); + if (len) + chip->read_buf(mtd, buf, len); + + return 0; +} +EXPORT_SYMBOL_GPL(nand_read_oob_op); + +/** + * nand_prog_page_begin_op - starts a PROG PAGE operation + * @chip: The NAND chip + * @page: page to write + * @offset_in_page: offset within the page + * @buf: buffer containing the data to write to the page + * @len: length of the buffer + * + * This function issues the first half of a PROG PAGE operation. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_prog_page_begin_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, const void *buf, + unsigned int len) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + if (len && !buf) + return -EINVAL; + + if (offset_in_page + len > mtd->writesize + mtd->oobsize) + return -EINVAL; + + chip->cmdfunc(mtd, NAND_CMD_SEQIN, offset_in_page, page); + + if (buf) + chip->write_buf(mtd, buf, len); + + return 0; +} +EXPORT_SYMBOL_GPL(nand_prog_page_begin_op); + +/** + * nand_prog_page_end_op - ends a PROG PAGE operation + * @chip: The NAND chip + * + * This function issues the second half of a PROG PAGE operation. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_prog_page_end_op(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + int status; + + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + + status = chip->waitfunc(mtd, chip); + if (status & NAND_STATUS_FAIL) + return -EIO; + + return 0; +} +EXPORT_SYMBOL_GPL(nand_prog_page_end_op); + +/** + * nand_prog_page_op - Do a full PROG PAGE operation + * @chip: The NAND chip + * @page: page to write + * @offset_in_page: offset within the page + * @buf: buffer containing the data to write to the page + * @len: length of the buffer + * + * This function issues a full PROG PAGE operation. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_prog_page_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, const void *buf, + unsigned int len) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + int status; + + if (!len || !buf) + return -EINVAL; + + if (offset_in_page + len > mtd->writesize + mtd->oobsize) + return -EINVAL; + + chip->cmdfunc(mtd, NAND_CMD_SEQIN, offset_in_page, page); + chip->write_buf(mtd, buf, len); + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + + status = chip->waitfunc(mtd, chip); + if (status & NAND_STATUS_FAIL) + return -EIO; + + return 0; +} +EXPORT_SYMBOL_GPL(nand_prog_page_op); + +/** + * nand_change_write_column_op - Do a CHANGE WRITE COLUMN operation + * @chip: The NAND chip + * @offset_in_page: offset within the page + * @buf: buffer containing the data to send to the NAND + * @len: length of the buffer + * @force_8bit: force 8-bit bus access + * + * This function issues a CHANGE WRITE COLUMN operation. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_change_write_column_op(struct nand_chip *chip, + unsigned int offset_in_page, + const void *buf, unsigned int len, + bool force_8bit) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + if (len && !buf) + return -EINVAL; + + if (offset_in_page + len > mtd->writesize + mtd->oobsize) + return -EINVAL; + + chip->cmdfunc(mtd, NAND_CMD_RNDIN, offset_in_page, -1); + if (len) + chip->write_buf(mtd, buf, len); + + return 0; +} +EXPORT_SYMBOL_GPL(nand_change_write_column_op); + +/** + * nand_readid_op - Do a READID operation + * @chip: The NAND chip + * @addr: address cycle to pass after the READID command + * @buf: buffer used to store the ID + * @len: length of the buffer + * + * This function sends a READID command and reads back the ID returned by the + * NAND. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_readid_op(struct nand_chip *chip, u8 addr, void *buf, + unsigned int len) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + unsigned int i; + u8 *id = buf; + + if (len && !buf) + return -EINVAL; + + chip->cmdfunc(mtd, NAND_CMD_READID, addr, -1); + + for (i = 0; i < len; i++) + id[i] = chip->read_byte(mtd); + + return 0; +} +EXPORT_SYMBOL_GPL(nand_readid_op); + +/** + * nand_status_op - Do a STATUS operation + * @chip: The NAND chip + * @status: out variable to store the NAND status + * + * This function sends a STATUS command and reads back the status returned by + * the NAND. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_status_op(struct nand_chip *chip, u8 *status) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); + if (status) + *status = chip->read_byte(mtd); + + return 0; +} +EXPORT_SYMBOL_GPL(nand_status_op); + +/** + * nand_exit_status_op - Exit a STATUS operation + * @chip: The NAND chip + * + * This function sends a READ0 command to cancel the effect of the STATUS + * command to avoid reading only the status until a new read command is sent. + * + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_exit_status_op(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + chip->cmdfunc(mtd, NAND_CMD_READ0, -1, -1); + + return 0; +} +EXPORT_SYMBOL_GPL(nand_exit_status_op); + +/** + * nand_erase_op - Do an erase operation + * @chip: The NAND chip + * @eraseblock: block to erase + * + * This function sends an ERASE command and waits for the NAND to be ready + * before returning. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_erase_op(struct nand_chip *chip, unsigned int eraseblock) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + unsigned int page = eraseblock << + (chip->phys_erase_shift - chip->page_shift); + int status; + + chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); + chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); + + status = chip->waitfunc(mtd, chip); + if (status < 0) + return status; + + if (status & NAND_STATUS_FAIL) + return -EIO; + + return 0; +} +EXPORT_SYMBOL_GPL(nand_erase_op); + +/** + * nand_set_features_op - Do a SET FEATURES operation + * @chip: The NAND chip + * @feature: feature id + * @data: 4 bytes of data + * + * This function sends a SET FEATURES command and waits for the NAND to be + * ready before returning. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +static int nand_set_features_op(struct nand_chip *chip, u8 feature, + const void *data) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + const u8 *params = data; + int i, status; + + chip->cmdfunc(mtd, NAND_CMD_SET_FEATURES, feature, -1); + for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) + chip->write_byte(mtd, params[i]); + + status = chip->waitfunc(mtd, chip); + if (status & NAND_STATUS_FAIL) + return -EIO; + + return 0; +} + +/** + * nand_get_features_op - Do a GET FEATURES operation + * @chip: The NAND chip + * @feature: feature id + * @data: 4 bytes of data + * + * This function sends a GET FEATURES command and waits for the NAND to be + * ready before returning. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +static int nand_get_features_op(struct nand_chip *chip, u8 feature, + void *data) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + u8 *params = data; + int i; + + chip->cmdfunc(mtd, NAND_CMD_GET_FEATURES, feature, -1); + for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) + params[i] = chip->read_byte(mtd); + + return 0; +} + +/** + * nand_reset_op - Do a reset operation + * @chip: The NAND chip + * + * This function sends a RESET command and waits for the NAND to be ready + * before returning. + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_reset_op(struct nand_chip *chip) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + + return 0; +} +EXPORT_SYMBOL_GPL(nand_reset_op); + +/** + * nand_read_data_op - Read data from the NAND + * @chip: The NAND chip + * @buf: buffer used to store the data + * @len: length of the buffer + * @force_8bit: force 8-bit bus access + * + * This function does a raw data read on the bus. Usually used after launching + * another NAND operation like nand_read_page_op(). + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_read_data_op(struct nand_chip *chip, void *buf, unsigned int len, + bool force_8bit) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + if (!len || !buf) + return -EINVAL; + + if (force_8bit) { + u8 *p = buf; + unsigned int i; + + for (i = 0; i < len; i++) + p[i] = chip->read_byte(mtd); + } else { + chip->read_buf(mtd, buf, len); + } + + return 0; +} +EXPORT_SYMBOL_GPL(nand_read_data_op); + +/** + * nand_write_data_op - Write data from the NAND + * @chip: The NAND chip + * @buf: buffer containing the data to send on the bus + * @len: length of the buffer + * @force_8bit: force 8-bit bus access + * + * This function does a raw data write on the bus. Usually used after launching + * another NAND operation like nand_write_page_begin_op(). + * This function does not select/unselect the CS line. + * + * Returns 0 on success, a negative error code otherwise. + */ +int nand_write_data_op(struct nand_chip *chip, const void *buf, + unsigned int len, bool force_8bit) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + if (!len || !buf) + return -EINVAL; + + if (force_8bit) { + const u8 *p = buf; + unsigned int i; + + for (i = 0; i < len; i++) + chip->write_byte(mtd, p[i]); + } else { + chip->write_buf(mtd, buf, len); + } + + return 0; +} +EXPORT_SYMBOL_GPL(nand_write_data_op); + /** * nand_reset - Reset and initialize a NAND device * @chip: The NAND chip @@ -1238,8 +1779,10 @@ int nand_reset(struct nand_chip *chip, int chipnr) * interface settings, hence this weird ->select_chip() dance. */ chip->select_chip(mtd, chipnr); - chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + ret = nand_reset_op(chip); chip->select_chip(mtd, -1); + if (ret) + return ret; chip->select_chip(mtd, chipnr); ret = nand_setup_data_interface(chip, chipnr); @@ -1395,9 +1938,19 @@ EXPORT_SYMBOL(nand_check_erased_ecc_chunk); int nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf, int oob_required, int page) { - chip->read_buf(mtd, buf, mtd->writesize); - if (oob_required) - chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + int ret; + + ret = nand_read_data_op(chip, buf, mtd->writesize, false); + if (ret) + return ret; + + if (oob_required) { + ret = nand_read_data_op(chip, chip->oob_poi, mtd->oobsize, + false); + if (ret) + return ret; + } + return 0; } EXPORT_SYMBOL(nand_read_page_raw); @@ -1419,29 +1972,46 @@ static int nand_read_page_raw_syndrome(struct mtd_info *mtd, int eccsize = chip->ecc.size; int eccbytes = chip->ecc.bytes; uint8_t *oob = chip->oob_poi; - int steps, size; + int steps, size, ret; for (steps = chip->ecc.steps; steps > 0; steps--) { - chip->read_buf(mtd, buf, eccsize); + ret = nand_read_data_op(chip, buf, eccsize, false); + if (ret) + return ret; + buf += eccsize; if (chip->ecc.prepad) { - chip->read_buf(mtd, oob, chip->ecc.prepad); + ret = nand_read_data_op(chip, oob, chip->ecc.prepad, + false); + if (ret) + return ret; + oob += chip->ecc.prepad; } - chip->read_buf(mtd, oob, eccbytes); + ret = nand_read_data_op(chip, oob, eccbytes, false); + if (ret) + return ret; + oob += eccbytes; if (chip->ecc.postpad) { - chip->read_buf(mtd, oob, chip->ecc.postpad); + ret = nand_read_data_op(chip, oob, chip->ecc.postpad, + false); + if (ret) + return ret; + oob += chip->ecc.postpad; } } size = mtd->oobsize - (oob - chip->oob_poi); - if (size) - chip->read_buf(mtd, oob, size); + if (size) { + ret = nand_read_data_op(chip, oob, size, false); + if (ret) + return ret; + } return 0; } @@ -1530,7 +2100,9 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, chip->cmdfunc(mtd, NAND_CMD_RNDOUT, data_col_addr, -1); p = bufpoi + data_col_addr; - chip->read_buf(mtd, p, datafrag_len); + ret = nand_read_data_op(chip, p, datafrag_len, false); + if (ret) + return ret; /* Calculate ECC */ for (i = 0; i < eccfrag_len ; i += chip->ecc.bytes, p += chip->ecc.size) @@ -1548,8 +2120,11 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, gaps = 1; if (gaps) { - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, mtd->writesize, -1); - chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + ret = nand_change_read_column_op(chip, mtd->writesize, + chip->oob_poi, mtd->oobsize, + false); + if (ret) + return ret; } else { /* * Send the command to read the particular ECC bytes take care @@ -1563,9 +2138,12 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, (busw - 1)) aligned_len++; - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, - mtd->writesize + aligned_pos, -1); - chip->read_buf(mtd, &chip->oob_poi[aligned_pos], aligned_len); + ret = nand_change_read_column_op(chip, + mtd->writesize + aligned_pos, + &chip->oob_poi[aligned_pos], + aligned_len, false); + if (ret) + return ret; } ret = mtd_ooblayout_get_eccbytes(mtd, chip->buffers->ecccode, @@ -1622,10 +2200,17 @@ static int nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { chip->ecc.hwctl(mtd, NAND_ECC_READ); - chip->read_buf(mtd, p, eccsize); + + ret = nand_read_data_op(chip, p, eccsize, false); + if (ret) + return ret; + chip->ecc.calculate(mtd, p, &ecc_calc[i]); } - chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); + + ret = nand_read_data_op(chip, chip->oob_poi, mtd->oobsize, false); + if (ret) + return ret; ret = mtd_ooblayout_get_eccbytes(mtd, ecc_code, chip->oob_poi, 0, chip->ecc.total); @@ -1684,9 +2269,13 @@ static int nand_read_page_hwecc_oob_first(struct mtd_info *mtd, unsigned int max_bitflips = 0; /* Read the OOB area first */ - chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); - chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); - chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + ret = nand_read_oob_op(chip, page, 0, chip->oob_poi, mtd->oobsize); + if (ret) + return ret; + + ret = nand_read_page_op(chip, page, 0, NULL, 0); + if (ret) + return ret; ret = mtd_ooblayout_get_eccbytes(mtd, ecc_code, chip->oob_poi, 0, chip->ecc.total); @@ -1697,7 +2286,11 @@ static int nand_read_page_hwecc_oob_first(struct mtd_info *mtd, int stat; chip->ecc.hwctl(mtd, NAND_ECC_READ); - chip->read_buf(mtd, p, eccsize); + + ret = nand_read_data_op(chip, p, eccsize, false); + if (ret) + return ret; + chip->ecc.calculate(mtd, p, &ecc_calc[i]); stat = chip->ecc.correct(mtd, p, &ecc_code[i], NULL); @@ -1734,7 +2327,7 @@ static int nand_read_page_hwecc_oob_first(struct mtd_info *mtd, static int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf, int oob_required, int page) { - int i, eccsize = chip->ecc.size; + int ret, i, eccsize = chip->ecc.size; int eccbytes = chip->ecc.bytes; int eccsteps = chip->ecc.steps; int eccpadbytes = eccbytes + chip->ecc.prepad + chip->ecc.postpad; @@ -1746,21 +2339,36 @@ static int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip, int stat; chip->ecc.hwctl(mtd, NAND_ECC_READ); - chip->read_buf(mtd, p, eccsize); + + ret = nand_read_data_op(chip, p, eccsize, false); + if (ret) + return ret; if (chip->ecc.prepad) { - chip->read_buf(mtd, oob, chip->ecc.prepad); + ret = nand_read_data_op(chip, oob, chip->ecc.prepad, + false); + if (ret) + return ret; + oob += chip->ecc.prepad; } chip->ecc.hwctl(mtd, NAND_ECC_READSYN); - chip->read_buf(mtd, oob, eccbytes); + + ret = nand_read_data_op(chip, oob, eccbytes, false); + if (ret) + return ret; + stat = chip->ecc.correct(mtd, p, oob, NULL); oob += eccbytes; if (chip->ecc.postpad) { - chip->read_buf(mtd, oob, chip->ecc.postpad); + ret = nand_read_data_op(chip, oob, chip->ecc.postpad, + false); + if (ret) + return ret; + oob += chip->ecc.postpad; } @@ -1784,8 +2392,11 @@ static int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip, /* Calculate remaining oob bytes */ i = mtd->oobsize - (oob - chip->oob_poi); - if (i) - chip->read_buf(mtd, oob, i); + if (i) { + ret = nand_read_data_op(chip, oob, i, false); + if (ret) + return ret; + } return max_bitflips; } @@ -1906,8 +2517,11 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, __func__, buf); read_retry: - if (nand_standard_page_accessors(&chip->ecc)) - chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page); + if (nand_standard_page_accessors(&chip->ecc)) { + ret = nand_read_page_op(chip, page, 0, NULL, 0); + if (ret) + break; + } /* * Now read the page into the buffer. Absent an error, @@ -2066,9 +2680,7 @@ static int nand_read(struct mtd_info *mtd, loff_t from, size_t len, */ int nand_read_oob_std(struct mtd_info *mtd, struct nand_chip *chip, int page) { - chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); - chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + return nand_read_oob_op(chip, page, 0, chip->oob_poi, mtd->oobsize); } EXPORT_SYMBOL(nand_read_oob_std); @@ -2086,25 +2698,43 @@ int nand_read_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip, int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad; int eccsize = chip->ecc.size; uint8_t *bufpoi = chip->oob_poi; - int i, toread, sndrnd = 0, pos; + int i, toread, sndrnd = 0, pos, ret; + + ret = nand_read_page_op(chip, page, chip->ecc.size, NULL, 0); + if (ret) + return ret; - chip->cmdfunc(mtd, NAND_CMD_READ0, chip->ecc.size, page); for (i = 0; i < chip->ecc.steps; i++) { if (sndrnd) { + int ret; + pos = eccsize + i * (eccsize + chunk); if (mtd->writesize > 512) - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, pos, -1); + ret = nand_change_read_column_op(chip, pos, + NULL, 0, + false); else - chip->cmdfunc(mtd, NAND_CMD_READ0, pos, page); + ret = nand_read_page_op(chip, page, pos, NULL, + 0); + + if (ret) + return ret; } else sndrnd = 1; toread = min_t(int, length, chunk); - chip->read_buf(mtd, bufpoi, toread); + + ret = nand_read_data_op(chip, bufpoi, toread, false); + if (ret) + return ret; + bufpoi += toread; length -= toread; } - if (length > 0) - chip->read_buf(mtd, bufpoi, length); + if (length > 0) { + ret = nand_read_data_op(chip, bufpoi, length, false); + if (ret) + return ret; + } return 0; } @@ -2118,18 +2748,8 @@ EXPORT_SYMBOL(nand_read_oob_syndrome); */ int nand_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip, int page) { - int status = 0; - const uint8_t *buf = chip->oob_poi; - int length = mtd->oobsize; - - chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page); - chip->write_buf(mtd, buf, length); - /* Send command to program the OOB data */ - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - - status = chip->waitfunc(mtd, chip); - - return status & NAND_STATUS_FAIL ? -EIO : 0; + return nand_prog_page_op(chip, page, mtd->writesize, chip->oob_poi, + mtd->oobsize); } EXPORT_SYMBOL(nand_write_oob_std); @@ -2145,7 +2765,7 @@ int nand_write_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip, { int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad; int eccsize = chip->ecc.size, length = mtd->oobsize; - int i, len, pos, status = 0, sndcmd = 0, steps = chip->ecc.steps; + int ret, i, len, pos, sndcmd = 0, steps = chip->ecc.steps; const uint8_t *bufpoi = chip->oob_poi; /* @@ -2159,7 +2779,10 @@ int nand_write_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip, } else pos = eccsize; - chip->cmdfunc(mtd, NAND_CMD_SEQIN, pos, page); + ret = nand_prog_page_begin_op(chip, page, pos, NULL, 0); + if (ret) + return ret; + for (i = 0; i < steps; i++) { if (sndcmd) { if (mtd->writesize <= 512) { @@ -2168,28 +2791,40 @@ int nand_write_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip, len = eccsize; while (len > 0) { int num = min_t(int, len, 4); - chip->write_buf(mtd, (uint8_t *)&fill, - num); + + ret = nand_write_data_op(chip, &fill, + num, false); + if (ret) + return ret; + len -= num; } } else { pos = eccsize + i * (eccsize + chunk); - chip->cmdfunc(mtd, NAND_CMD_RNDIN, pos, -1); + ret = nand_change_write_column_op(chip, pos, + NULL, 0, + false); + if (ret) + return ret; } } else sndcmd = 1; len = min_t(int, length, chunk); - chip->write_buf(mtd, bufpoi, len); + + ret = nand_write_data_op(chip, bufpoi, len, false); + if (ret) + return ret; + bufpoi += len; length -= len; } - if (length > 0) - chip->write_buf(mtd, bufpoi, length); - - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - status = chip->waitfunc(mtd, chip); + if (length > 0) { + ret = nand_write_data_op(chip, bufpoi, length, false); + if (ret) + return ret; + } - return status & NAND_STATUS_FAIL ? -EIO : 0; + return nand_prog_page_end_op(chip); } EXPORT_SYMBOL(nand_write_oob_syndrome); @@ -2341,9 +2976,18 @@ static int nand_read_oob(struct mtd_info *mtd, loff_t from, int nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required, int page) { - chip->write_buf(mtd, buf, mtd->writesize); - if (oob_required) - chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + int ret; + + ret = nand_write_data_op(chip, buf, mtd->writesize, false); + if (ret) + return ret; + + if (oob_required) { + ret = nand_write_data_op(chip, chip->oob_poi, mtd->oobsize, + false); + if (ret) + return ret; + } return 0; } @@ -2367,29 +3011,46 @@ static int nand_write_page_raw_syndrome(struct mtd_info *mtd, int eccsize = chip->ecc.size; int eccbytes = chip->ecc.bytes; uint8_t *oob = chip->oob_poi; - int steps, size; + int steps, size, ret; for (steps = chip->ecc.steps; steps > 0; steps--) { - chip->write_buf(mtd, buf, eccsize); + ret = nand_write_data_op(chip, buf, eccsize, false); + if (ret) + return ret; + buf += eccsize; if (chip->ecc.prepad) { - chip->write_buf(mtd, oob, chip->ecc.prepad); + ret = nand_write_data_op(chip, oob, chip->ecc.prepad, + false); + if (ret) + return ret; + oob += chip->ecc.prepad; } - chip->write_buf(mtd, oob, eccbytes); + ret = nand_write_data_op(chip, oob, eccbytes, false); + if (ret) + return ret; + oob += eccbytes; if (chip->ecc.postpad) { - chip->write_buf(mtd, oob, chip->ecc.postpad); + ret = nand_write_data_op(chip, oob, chip->ecc.postpad, + false); + if (ret) + return ret; + oob += chip->ecc.postpad; } } size = mtd->oobsize - (oob - chip->oob_poi); - if (size) - chip->write_buf(mtd, oob, size); + if (size) { + ret = nand_write_data_op(chip, oob, size, false); + if (ret) + return ret; + } return 0; } @@ -2443,7 +3104,11 @@ static int nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { chip->ecc.hwctl(mtd, NAND_ECC_WRITE); - chip->write_buf(mtd, p, eccsize); + + ret = nand_write_data_op(chip, p, eccsize, false); + if (ret) + return ret; + chip->ecc.calculate(mtd, p, &ecc_calc[i]); } @@ -2452,7 +3117,9 @@ static int nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, if (ret) return ret; - chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + ret = nand_write_data_op(chip, chip->oob_poi, mtd->oobsize, false); + if (ret) + return ret; return 0; } @@ -2488,7 +3155,9 @@ static int nand_write_subpage_hwecc(struct mtd_info *mtd, chip->ecc.hwctl(mtd, NAND_ECC_WRITE); /* write data (untouched subpages already masked by 0xFF) */ - chip->write_buf(mtd, buf, ecc_size); + ret = nand_write_data_op(chip, buf, ecc_size, false); + if (ret) + return ret; /* mask ECC of un-touched subpages by padding 0xFF */ if ((step < start_step) || (step > end_step)) @@ -2515,7 +3184,9 @@ static int nand_write_subpage_hwecc(struct mtd_info *mtd, return ret; /* write OOB buffer to NAND device */ - chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); + ret = nand_write_data_op(chip, chip->oob_poi, mtd->oobsize, false); + if (ret) + return ret; return 0; } @@ -2542,31 +3213,49 @@ static int nand_write_page_syndrome(struct mtd_info *mtd, int eccsteps = chip->ecc.steps; const uint8_t *p = buf; uint8_t *oob = chip->oob_poi; + int ret; for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { - chip->ecc.hwctl(mtd, NAND_ECC_WRITE); - chip->write_buf(mtd, p, eccsize); + + ret = nand_write_data_op(chip, p, eccsize, false); + if (ret) + return ret; if (chip->ecc.prepad) { - chip->write_buf(mtd, oob, chip->ecc.prepad); + ret = nand_write_data_op(chip, oob, chip->ecc.prepad, + false); + if (ret) + return ret; + oob += chip->ecc.prepad; } chip->ecc.calculate(mtd, p, oob); - chip->write_buf(mtd, oob, eccbytes); + + ret = nand_write_data_op(chip, oob, eccbytes, false); + if (ret) + return ret; + oob += eccbytes; if (chip->ecc.postpad) { - chip->write_buf(mtd, oob, chip->ecc.postpad); + ret = nand_write_data_op(chip, oob, chip->ecc.postpad, + false); + if (ret) + return ret; + oob += chip->ecc.postpad; } } /* Calculate remaining oob bytes */ i = mtd->oobsize - (oob - chip->oob_poi); - if (i) - chip->write_buf(mtd, oob, i); + if (i) { + ret = nand_write_data_op(chip, oob, i, false); + if (ret) + return ret; + } return 0; } @@ -2594,8 +3283,11 @@ static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip, else subpage = 0; - if (nand_standard_page_accessors(&chip->ecc)) - chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page); + if (nand_standard_page_accessors(&chip->ecc)) { + status = nand_prog_page_begin_op(chip, page, 0, NULL, 0); + if (status) + return status; + } if (unlikely(raw)) status = chip->ecc.write_page_raw(mtd, chip, buf, @@ -2610,13 +3302,8 @@ static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip, if (status < 0) return status; - if (nand_standard_page_accessors(&chip->ecc)) { - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - - status = chip->waitfunc(mtd, chip); - if (status & NAND_STATUS_FAIL) - return -EIO; - } + if (nand_standard_page_accessors(&chip->ecc)) + return nand_prog_page_end_op(chip); return 0; } @@ -2989,17 +3676,12 @@ out: static int single_erase(struct mtd_info *mtd, int page) { struct nand_chip *chip = mtd_to_nand(mtd); - int status; + unsigned int eraseblock; /* Send commands to erase a block */ - chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); - chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); + eraseblock = page >> (chip->phys_erase_shift - chip->page_shift); - status = chip->waitfunc(mtd, chip); - if (status < 0) - return status; - - return status & NAND_STATUS_FAIL ? -EIO : 0; + return nand_erase_op(chip, eraseblock); } /** @@ -3226,22 +3908,12 @@ static int nand_max_bad_blocks(struct mtd_info *mtd, loff_t ofs, size_t len) static int nand_onfi_set_features(struct mtd_info *mtd, struct nand_chip *chip, int addr, uint8_t *subfeature_param) { - int status; - int i; - if (!chip->onfi_version || !(le16_to_cpu(chip->onfi_params.opt_cmd) & ONFI_OPT_CMD_SET_GET_FEATURES)) return -EINVAL; - chip->cmdfunc(mtd, NAND_CMD_SET_FEATURES, addr, -1); - for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) - chip->write_byte(mtd, subfeature_param[i]); - - status = chip->waitfunc(mtd, chip); - if (status & NAND_STATUS_FAIL) - return -EIO; - return 0; + return nand_set_features_op(chip, addr, subfeature_param); } /** @@ -3254,17 +3926,12 @@ static int nand_onfi_set_features(struct mtd_info *mtd, struct nand_chip *chip, static int nand_onfi_get_features(struct mtd_info *mtd, struct nand_chip *chip, int addr, uint8_t *subfeature_param) { - int i; - if (!chip->onfi_version || !(le16_to_cpu(chip->onfi_params.opt_cmd) & ONFI_OPT_CMD_SET_GET_FEATURES)) return -EINVAL; - chip->cmdfunc(mtd, NAND_CMD_GET_FEATURES, addr, -1); - for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) - *subfeature_param++ = chip->read_byte(mtd); - return 0; + return nand_get_features_op(chip, addr, subfeature_param); } /** @@ -3407,12 +4074,11 @@ static u16 onfi_crc16(u16 crc, u8 const *p, size_t len) static int nand_flash_detect_ext_param_page(struct nand_chip *chip, struct nand_onfi_params *p) { - struct mtd_info *mtd = nand_to_mtd(chip); struct onfi_ext_param_page *ep; struct onfi_ext_section *s; struct onfi_ext_ecc_info *ecc; uint8_t *cursor; - int ret = -EINVAL; + int ret; int len; int i; @@ -3422,14 +4088,18 @@ static int nand_flash_detect_ext_param_page(struct nand_chip *chip, return -ENOMEM; /* Send our own NAND_CMD_PARAM. */ - chip->cmdfunc(mtd, NAND_CMD_PARAM, 0, -1); + ret = nand_read_param_page_op(chip, 0, NULL, 0); + if (ret) + goto ext_out; /* Use the Change Read Column command to skip the ONFI param pages. */ - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, - sizeof(*p) * p->num_of_param_pages , -1); + ret = nand_change_read_column_op(chip, + sizeof(*p) * p->num_of_param_pages, + ep, len, true); + if (ret) + goto ext_out; - /* Read out the Extended Parameter Page. */ - chip->read_buf(mtd, (uint8_t *)ep, len); + ret = -EINVAL; if ((onfi_crc16(ONFI_CRC_BASE, ((uint8_t *)ep) + 2, len - 2) != le16_to_cpu(ep->crc))) { pr_debug("fail in the CRC.\n"); @@ -3482,19 +4152,23 @@ static int nand_flash_detect_onfi(struct nand_chip *chip) { struct mtd_info *mtd = nand_to_mtd(chip); struct nand_onfi_params *p = &chip->onfi_params; - int i, j; - int val; + char id[4]; + int i, ret, val; /* Try ONFI for unknown chip or LP */ - chip->cmdfunc(mtd, NAND_CMD_READID, 0x20, -1); - if (chip->read_byte(mtd) != 'O' || chip->read_byte(mtd) != 'N' || - chip->read_byte(mtd) != 'F' || chip->read_byte(mtd) != 'I') + ret = nand_readid_op(chip, 0x20, id, sizeof(id)); + if (ret || strncmp(id, "ONFI", 4)) + return 0; + + ret = nand_read_param_page_op(chip, 0, NULL, 0); + if (ret) return 0; - chip->cmdfunc(mtd, NAND_CMD_PARAM, 0, -1); for (i = 0; i < 3; i++) { - for (j = 0; j < sizeof(*p); j++) - ((uint8_t *)p)[j] = chip->read_byte(mtd); + ret = nand_read_data_op(chip, p, sizeof(*p), true); + if (ret) + return 0; + if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 254) == le16_to_cpu(p->crc)) { break; @@ -3585,20 +4259,22 @@ static int nand_flash_detect_jedec(struct nand_chip *chip) struct mtd_info *mtd = nand_to_mtd(chip); struct nand_jedec_params *p = &chip->jedec_params; struct jedec_ecc_info *ecc; - int val; - int i, j; + char id[5]; + int i, val, ret; /* Try JEDEC for unknown chip or LP */ - chip->cmdfunc(mtd, NAND_CMD_READID, 0x40, -1); - if (chip->read_byte(mtd) != 'J' || chip->read_byte(mtd) != 'E' || - chip->read_byte(mtd) != 'D' || chip->read_byte(mtd) != 'E' || - chip->read_byte(mtd) != 'C') + ret = nand_readid_op(chip, 0x40, id, sizeof(id)); + if (ret || strncmp(id, "JEDEC", sizeof(id))) + return 0; + + ret = nand_read_param_page_op(chip, 0x40, NULL, 0); + if (ret) return 0; - chip->cmdfunc(mtd, NAND_CMD_PARAM, 0x40, -1); for (i = 0; i < 3; i++) { - for (j = 0; j < sizeof(*p); j++) - ((uint8_t *)p)[j] = chip->read_byte(mtd); + ret = nand_read_data_op(chip, p, sizeof(*p), true); + if (ret) + return 0; if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 510) == le16_to_cpu(p->crc)) @@ -3877,8 +4553,7 @@ static int nand_detect(struct nand_chip *chip, struct nand_flash_dev *type) { const struct nand_manufacturer *manufacturer; struct mtd_info *mtd = nand_to_mtd(chip); - int busw; - int i; + int busw, ret; u8 *id_data = chip->id.data; u8 maf_id, dev_id; @@ -3886,17 +4561,21 @@ static int nand_detect(struct nand_chip *chip, struct nand_flash_dev *type) * Reset the chip, required by some chips (e.g. Micron MT29FxGxxxxx) * after power-up. */ - nand_reset(chip, 0); + ret = nand_reset(chip, 0); + if (ret) + return ret; /* Select the device */ chip->select_chip(mtd, 0); /* Send the command for reading device ID */ - chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); + ret = nand_readid_op(chip, 0, id_data, 2); + if (ret) + return ret; /* Read manufacturer and device IDs */ - maf_id = chip->read_byte(mtd); - dev_id = chip->read_byte(mtd); + maf_id = id_data[0]; + dev_id = id_data[1]; /* * Try again to make sure, as some systems the bus-hold or other @@ -3905,11 +4584,10 @@ static int nand_detect(struct nand_chip *chip, struct nand_flash_dev *type) * not match, ignore the device completely. */ - chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); - /* Read entire ID string */ - for (i = 0; i < ARRAY_SIZE(chip->id.data); i++) - id_data[i] = chip->read_byte(mtd); + ret = nand_readid_op(chip, 0, id_data, sizeof(chip->id.data)); + if (ret) + return ret; if (id_data[0] != maf_id || id_data[1] != dev_id) { pr_info("second ID read did not match %02x,%02x against %02x,%02x\n", @@ -4236,15 +4914,16 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips, /* Check for a chip array */ for (i = 1; i < maxchips; i++) { + u8 id[2]; + /* See comment in nand_get_flash_type for reset */ nand_reset(chip, i); chip->select_chip(mtd, i); /* Send the command for reading device ID */ - chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); + nand_readid_op(chip, 0, id, sizeof(id)); /* Read manufacturer and device IDs */ - if (nand_maf_id != chip->read_byte(mtd) || - nand_dev_id != chip->read_byte(mtd)) { + if (nand_maf_id != id[0] || nand_dev_id != id[1]) { chip->select_chip(mtd, -1); break; } diff --git a/drivers/mtd/nand/nand_hynix.c b/drivers/mtd/nand/nand_hynix.c index 72d98cbff4ca..bae0da2aa2a8 100644 --- a/drivers/mtd/nand/nand_hynix.c +++ b/drivers/mtd/nand/nand_hynix.c @@ -66,16 +66,35 @@ struct hynix_read_retry_otp { }; static bool hynix_nand_has_valid_jedecid(struct nand_chip *chip) +{ + u8 jedecid[5] = { }; + int ret; + + ret = nand_readid_op(chip, 0x40, jedecid, sizeof(jedecid)); + if (ret) + return false; + + return !strncmp("JEDEC", jedecid, sizeof(jedecid)); +} + +static int hynix_nand_cmd_op(struct nand_chip *chip, u8 cmd) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + chip->cmdfunc(mtd, cmd, -1, -1); + + return 0; +} + +static int hynix_nand_reg_write_op(struct nand_chip *chip, u8 addr, u8 val) { struct mtd_info *mtd = nand_to_mtd(chip); - u8 jedecid[6] = { }; - int i = 0; + u16 column = ((u16)addr << 8) | addr; - chip->cmdfunc(mtd, NAND_CMD_READID, 0x40, -1); - for (i = 0; i < 5; i++) - jedecid[i] = chip->read_byte(mtd); + chip->cmdfunc(mtd, NAND_CMD_NONE, column, -1); + chip->write_byte(mtd, val); - return !strcmp("JEDEC", jedecid); + return 0; } static int hynix_nand_setup_read_retry(struct mtd_info *mtd, int retry_mode) @@ -83,13 +102,15 @@ static int hynix_nand_setup_read_retry(struct mtd_info *mtd, int retry_mode) struct nand_chip *chip = mtd_to_nand(mtd); struct hynix_nand *hynix = nand_get_manufacturer_data(chip); const u8 *values; - int i; + int i, ret; values = hynix->read_retry->values + (retry_mode * hynix->read_retry->nregs); /* Enter 'Set Hynix Parameters' mode */ - chip->cmdfunc(mtd, NAND_HYNIX_CMD_SET_PARAMS, -1, -1); + ret = hynix_nand_cmd_op(chip, NAND_HYNIX_CMD_SET_PARAMS); + if (ret) + return ret; /* * Configure the NAND in the requested read-retry mode. @@ -101,17 +122,14 @@ static int hynix_nand_setup_read_retry(struct mtd_info *mtd, int retry_mode) * probably tweaked at production in this case). */ for (i = 0; i < hynix->read_retry->nregs; i++) { - int column = hynix->read_retry->regs[i]; - - column |= column << 8; - chip->cmdfunc(mtd, NAND_CMD_NONE, column, -1); - chip->write_byte(mtd, values[i]); + ret = hynix_nand_reg_write_op(chip, hynix->read_retry->regs[i], + values[i]); + if (ret) + return ret; } /* Apply the new settings. */ - chip->cmdfunc(mtd, NAND_HYNIX_CMD_APPLY_PARAMS, -1, -1); - - return 0; + return hynix_nand_cmd_op(chip, NAND_HYNIX_CMD_APPLY_PARAMS); } /** @@ -167,40 +185,63 @@ static int hynix_read_rr_otp(struct nand_chip *chip, const struct hynix_read_retry_otp *info, void *buf) { - struct mtd_info *mtd = nand_to_mtd(chip); - int i; + int i, ret; - chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + ret = nand_reset_op(chip); + if (ret) + return ret; - chip->cmdfunc(mtd, NAND_HYNIX_CMD_SET_PARAMS, -1, -1); + ret = hynix_nand_cmd_op(chip, NAND_HYNIX_CMD_SET_PARAMS); + if (ret) + return ret; for (i = 0; i < info->nregs; i++) { - int column = info->regs[i]; - - column |= column << 8; - chip->cmdfunc(mtd, NAND_CMD_NONE, column, -1); - chip->write_byte(mtd, info->values[i]); + ret = hynix_nand_reg_write_op(chip, info->regs[i], + info->values[i]); + if (ret) + return ret; } - chip->cmdfunc(mtd, NAND_HYNIX_CMD_APPLY_PARAMS, -1, -1); + ret = hynix_nand_cmd_op(chip, NAND_HYNIX_CMD_APPLY_PARAMS); + if (ret) + return ret; /* Sequence to enter OTP mode? */ - chip->cmdfunc(mtd, 0x17, -1, -1); - chip->cmdfunc(mtd, 0x04, -1, -1); - chip->cmdfunc(mtd, 0x19, -1, -1); + ret = hynix_nand_cmd_op(chip, 0x17); + if (ret) + return ret; + + ret = hynix_nand_cmd_op(chip, 0x4); + if (ret) + return ret; + + ret = hynix_nand_cmd_op(chip, 0x19); + if (ret) + return ret; /* Now read the page */ - chip->cmdfunc(mtd, NAND_CMD_READ0, 0x0, info->page); - chip->read_buf(mtd, buf, info->size); + ret = nand_read_page_op(chip, info->page, 0, buf, info->size); + if (ret) + return ret; /* Put everything back to normal */ - chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); - chip->cmdfunc(mtd, NAND_HYNIX_CMD_SET_PARAMS, 0x38, -1); - chip->write_byte(mtd, 0x0); - chip->cmdfunc(mtd, NAND_HYNIX_CMD_APPLY_PARAMS, -1, -1); - chip->cmdfunc(mtd, NAND_CMD_READ0, 0x0, -1); + ret = nand_reset_op(chip); + if (ret) + return ret; - return 0; + ret = hynix_nand_cmd_op(chip, NAND_HYNIX_CMD_SET_PARAMS); + if (ret) + return ret; + + ret = hynix_nand_reg_write_op(chip, 0x38, 0); + if (ret) + return ret; + + ret = hynix_nand_cmd_op(chip, NAND_HYNIX_CMD_APPLY_PARAMS); + if (ret) + return ret; + + return nand_read_page_op(chip, 0, 0, NULL, 0); } #define NAND_HYNIX_1XNM_RR_COUNT_OFFS 0 diff --git a/drivers/mtd/nand/nand_micron.c b/drivers/mtd/nand/nand_micron.c index abf6a3c376e8..bf2dc23e1c32 100644 --- a/drivers/mtd/nand/nand_micron.c +++ b/drivers/mtd/nand/nand_micron.c @@ -117,16 +117,28 @@ micron_nand_read_page_on_die_ecc(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf, int oob_required, int page) { - int status; - int max_bitflips = 0; + u8 status; + int ret, max_bitflips = 0; - micron_nand_on_die_ecc_setup(chip, true); + ret = micron_nand_on_die_ecc_setup(chip, true); + if (ret) + return ret; + + ret = nand_read_page_op(chip, page, 0, NULL, 0); + if (ret) + goto out; + + ret = nand_status_op(chip, &status); + if (ret) + goto out; + + ret = nand_exit_status_op(chip); + if (ret) + goto out; - chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page); - chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); - status = chip->read_byte(mtd); if (status & NAND_STATUS_FAIL) mtd->ecc_stats.failed++; + /* * The internal ECC doesn't tell us the number of bitflips * that have been corrected, but tells us if it recommends to @@ -137,13 +149,12 @@ micron_nand_read_page_on_die_ecc(struct mtd_info *mtd, struct nand_chip *chip, else if (status & NAND_STATUS_WRITE_RECOMMENDED) max_bitflips = chip->ecc.strength; - chip->cmdfunc(mtd, NAND_CMD_READ0, -1, -1); - - nand_read_page_raw(mtd, chip, buf, oob_required, page); + ret = nand_read_page_raw(mtd, chip, buf, oob_required, page); +out: micron_nand_on_die_ecc_setup(chip, false); - return max_bitflips; + return ret ? ret : max_bitflips; } static int @@ -151,18 +162,26 @@ micron_nand_write_page_on_die_ecc(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required, int page) { - int status; + int ret; - micron_nand_on_die_ecc_setup(chip, true); + ret = micron_nand_on_die_ecc_setup(chip, true); + if (ret) + return ret; - chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page); - nand_write_page_raw(mtd, chip, buf, oob_required, page); - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - status = chip->waitfunc(mtd, chip); + ret = nand_prog_page_begin_op(chip, page, 0, NULL, 0); + if (ret) + goto out; + ret = nand_write_page_raw(mtd, chip, buf, oob_required, page); + if (ret) + return ret; + + ret = nand_prog_page_end_op(chip); + +out: micron_nand_on_die_ecc_setup(chip, false); - return status & NAND_STATUS_FAIL ? -EIO : 0; + return ret; } static int @@ -171,10 +190,13 @@ micron_nand_read_page_raw_on_die_ecc(struct mtd_info *mtd, uint8_t *buf, int oob_required, int page) { - chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page); - nand_read_page_raw(mtd, chip, buf, oob_required, page); + int ret; - return 0; + ret = nand_read_page_op(chip, page, 0, NULL, 0); + if (ret) + return ret; + + return nand_read_page_raw(mtd, chip, buf, oob_required, page); } static int @@ -183,14 +205,17 @@ micron_nand_write_page_raw_on_die_ecc(struct mtd_info *mtd, const uint8_t *buf, int oob_required, int page) { - int status; + int ret; - chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page); - nand_write_page_raw(mtd, chip, buf, oob_required, page); - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - status = chip->waitfunc(mtd, chip); + ret = nand_prog_page_begin_op(chip, page, 0, NULL, 0); + if (ret) + return ret; + + ret = nand_write_page_raw(mtd, chip, buf, oob_required, page); + if (ret) + return ret; - return status & NAND_STATUS_FAIL ? -EIO : 0; + return nand_prog_page_end_op(chip); } enum { diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index dad438c4906a..6e1b209cd5a7 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -1647,10 +1647,10 @@ static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip, chip->read_buf(mtd, buf, mtd->writesize); /* Read oob bytes */ - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, - mtd->writesize + BADBLOCK_MARKER_LENGTH, -1); - chip->read_buf(mtd, chip->oob_poi + BADBLOCK_MARKER_LENGTH, - chip->ecc.total); + nand_change_read_column_op(chip, + mtd->writesize + BADBLOCK_MARKER_LENGTH, + chip->oob_poi + BADBLOCK_MARKER_LENGTH, + chip->ecc.total, false); /* Calculate ecc bytes */ omap_calculate_ecc_bch_multi(mtd, buf, ecc_calc); diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c index 90b9a9ccbe60..28bcdf64c1fc 100644 --- a/drivers/mtd/nand/pxa3xx_nand.c +++ b/drivers/mtd/nand/pxa3xx_nand.c @@ -520,15 +520,13 @@ static int pxa3xx_nand_init_timings_compat(struct pxa3xx_nand_host *host, struct nand_chip *chip = &host->chip; struct pxa3xx_nand_info *info = host->info_data; const struct pxa3xx_nand_flash *f = NULL; - struct mtd_info *mtd = nand_to_mtd(&host->chip); int i, id, ntypes; + u8 idbuf[2]; ntypes = ARRAY_SIZE(builtin_flash_types); - chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); - - id = chip->read_byte(mtd); - id |= chip->read_byte(mtd) << 0x8; + nand_readid_op(chip, 0, idbuf, sizeof(idbuf)); + id = idbuf[0] | (idbuf[1] << 8); for (i = 0; i < ntypes; i++) { f = &builtin_flash_types[i]; diff --git a/drivers/mtd/nand/qcom_nandc.c b/drivers/mtd/nand/qcom_nandc.c index 2656c1ac5646..e34313ecd903 100644 --- a/drivers/mtd/nand/qcom_nandc.c +++ b/drivers/mtd/nand/qcom_nandc.c @@ -1990,7 +1990,7 @@ static int qcom_nandc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, struct nand_ecc_ctrl *ecc = &chip->ecc; u8 *oob = chip->oob_poi; int data_size, oob_size; - int ret, status = 0; + int ret; host->use_ecc = true; @@ -2027,11 +2027,7 @@ static int qcom_nandc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, return -EIO; } - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - - status = chip->waitfunc(mtd, chip); - - return status & NAND_STATUS_FAIL ? -EIO : 0; + return nand_prog_page_end_op(chip); } static int qcom_nandc_block_bad(struct mtd_info *mtd, loff_t ofs) @@ -2081,7 +2077,7 @@ static int qcom_nandc_block_markbad(struct mtd_info *mtd, loff_t ofs) struct qcom_nand_host *host = to_qcom_nand_host(chip); struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); struct nand_ecc_ctrl *ecc = &chip->ecc; - int page, ret, status = 0; + int page, ret; clear_read_regs(nandc); clear_bam_transaction(nandc); @@ -2114,11 +2110,7 @@ static int qcom_nandc_block_markbad(struct mtd_info *mtd, loff_t ofs) return -EIO; } - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - - status = chip->waitfunc(mtd, chip); - - return status & NAND_STATUS_FAIL ? -EIO : 0; + return nand_prog_page_end_op(chip); } /* diff --git a/drivers/mtd/nand/r852.c b/drivers/mtd/nand/r852.c index fc9287af4614..595635b9e9de 100644 --- a/drivers/mtd/nand/r852.c +++ b/drivers/mtd/nand/r852.c @@ -364,7 +364,7 @@ static int r852_wait(struct mtd_info *mtd, struct nand_chip *chip) struct r852_device *dev = nand_get_controller_data(chip); unsigned long timeout; - int status; + u8 status; timeout = jiffies + (chip->state == FL_ERASING ? msecs_to_jiffies(400) : msecs_to_jiffies(20)); @@ -373,8 +373,7 @@ static int r852_wait(struct mtd_info *mtd, struct nand_chip *chip) if (chip->dev_ready(mtd)) break; - chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); - status = (int)chip->read_byte(mtd); + nand_status_op(chip, &status); /* Unfortunelly, no way to send detailed error status... */ if (dev->dma_error) { @@ -522,9 +521,7 @@ exit: static int r852_read_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { - chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); - chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + return nand_read_oob_op(chip, page, 0, chip->oob_poi, mtd->oobsize); } /* @@ -1046,7 +1043,7 @@ static int r852_resume(struct device *device) if (dev->card_registred) { r852_engine_enable(dev); dev->chip->select_chip(mtd, 0); - dev->chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); + nand_reset_op(dev->chip); dev->chip->select_chip(mtd, -1); } diff --git a/drivers/mtd/nand/sunxi_nand.c b/drivers/mtd/nand/sunxi_nand.c index 82244be3e766..da5cc36f4c30 100644 --- a/drivers/mtd/nand/sunxi_nand.c +++ b/drivers/mtd/nand/sunxi_nand.c @@ -958,12 +958,12 @@ static int sunxi_nfc_hw_ecc_read_chunk(struct mtd_info *mtd, int ret; if (*cur_off != data_off) - nand->cmdfunc(mtd, NAND_CMD_RNDOUT, data_off, -1); + nand_change_read_column_op(nand, data_off, NULL, 0, false); sunxi_nfc_randomizer_read_buf(mtd, NULL, ecc->size, false, page); if (data_off + ecc->size != oob_off) - nand->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_off, -1); + nand_change_read_column_op(nand, oob_off, NULL, 0, false); ret = sunxi_nfc_wait_cmd_fifo_empty(nfc); if (ret) @@ -991,16 +991,15 @@ static int sunxi_nfc_hw_ecc_read_chunk(struct mtd_info *mtd, * Re-read the data with the randomizer disabled to identify * bitflips in erased pages. */ - if (nand->options & NAND_NEED_SCRAMBLING) { - nand->cmdfunc(mtd, NAND_CMD_RNDOUT, data_off, -1); - nand->read_buf(mtd, data, ecc->size); - } else { + if (nand->options & NAND_NEED_SCRAMBLING) + nand_change_read_column_op(nand, data_off, data, + ecc->size, false); + else memcpy_fromio(data, nfc->regs + NFC_RAM0_BASE, ecc->size); - } - nand->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_off, -1); - nand->read_buf(mtd, oob, ecc->bytes + 4); + nand_change_read_column_op(nand, oob_off, oob, ecc->bytes + 4, + false); ret = nand_check_erased_ecc_chunk(data, ecc->size, oob, ecc->bytes + 4, @@ -1011,7 +1010,8 @@ static int sunxi_nfc_hw_ecc_read_chunk(struct mtd_info *mtd, memcpy_fromio(data, nfc->regs + NFC_RAM0_BASE, ecc->size); if (oob_required) { - nand->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_off, -1); + nand_change_read_column_op(nand, oob_off, NULL, 0, + false); sunxi_nfc_randomizer_read_buf(mtd, oob, ecc->bytes + 4, true, page); @@ -1038,8 +1038,8 @@ static void sunxi_nfc_hw_ecc_read_extra_oob(struct mtd_info *mtd, return; if (!cur_off || *cur_off != offset) - nand->cmdfunc(mtd, NAND_CMD_RNDOUT, - offset + mtd->writesize, -1); + nand_change_read_column_op(nand, mtd->writesize, NULL, 0, + false); if (!randomize) sunxi_nfc_read_buf(mtd, oob + offset, len); @@ -1116,9 +1116,9 @@ static int sunxi_nfc_hw_ecc_read_chunks_dma(struct mtd_info *mtd, uint8_t *buf, if (oob_required && !erased) { /* TODO: use DMA to retrieve OOB */ - nand->cmdfunc(mtd, NAND_CMD_RNDOUT, - mtd->writesize + oob_off, -1); - nand->read_buf(mtd, oob, ecc->bytes + 4); + nand_change_read_column_op(nand, + mtd->writesize + oob_off, + oob, ecc->bytes + 4, false); sunxi_nfc_hw_ecc_get_prot_oob_bytes(mtd, oob, i, !i, page); @@ -1143,18 +1143,17 @@ static int sunxi_nfc_hw_ecc_read_chunks_dma(struct mtd_info *mtd, uint8_t *buf, /* * Re-read the data with the randomizer disabled to * identify bitflips in erased pages. + * TODO: use DMA to read page in raw mode */ - if (randomized) { - /* TODO: use DMA to read page in raw mode */ - nand->cmdfunc(mtd, NAND_CMD_RNDOUT, - data_off, -1); - nand->read_buf(mtd, data, ecc->size); - } + if (randomized) + nand_change_read_column_op(nand, data_off, + data, ecc->size, + false); /* TODO: use DMA to retrieve OOB */ - nand->cmdfunc(mtd, NAND_CMD_RNDOUT, - mtd->writesize + oob_off, -1); - nand->read_buf(mtd, oob, ecc->bytes + 4); + nand_change_read_column_op(nand, + mtd->writesize + oob_off, + oob, ecc->bytes + 4, false); ret = nand_check_erased_ecc_chunk(data, ecc->size, oob, ecc->bytes + 4, @@ -1187,12 +1186,12 @@ static int sunxi_nfc_hw_ecc_write_chunk(struct mtd_info *mtd, int ret; if (data_off != *cur_off) - nand->cmdfunc(mtd, NAND_CMD_RNDIN, data_off, -1); + nand_change_write_column_op(nand, data_off, NULL, 0, false); sunxi_nfc_randomizer_write_buf(mtd, data, ecc->size, false, page); if (data_off + ecc->size != oob_off) - nand->cmdfunc(mtd, NAND_CMD_RNDIN, oob_off, -1); + nand_change_write_column_op(nand, oob_off, NULL, 0, false); ret = sunxi_nfc_wait_cmd_fifo_empty(nfc); if (ret) @@ -1228,8 +1227,8 @@ static void sunxi_nfc_hw_ecc_write_extra_oob(struct mtd_info *mtd, return; if (!cur_off || *cur_off != offset) - nand->cmdfunc(mtd, NAND_CMD_RNDIN, - offset + mtd->writesize, -1); + nand_change_write_column_op(nand, offset + mtd->writesize, + NULL, 0, false); sunxi_nfc_randomizer_write_buf(mtd, oob + offset, len, false, page); @@ -1285,7 +1284,7 @@ static int sunxi_nfc_hw_ecc_read_page_dma(struct mtd_info *mtd, return ret; /* Fallback to PIO mode */ - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, 0, -1); + nand_change_read_column_op(chip, 0, NULL, 0, false); return sunxi_nfc_hw_ecc_read_page(mtd, chip, buf, oob_required, page); } @@ -1335,7 +1334,7 @@ static int sunxi_nfc_hw_ecc_read_subpage_dma(struct mtd_info *mtd, return ret; /* Fallback to PIO mode */ - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, 0, -1); + nand_change_read_column_op(chip, 0, NULL, 0, false); return sunxi_nfc_hw_ecc_read_subpage(mtd, chip, data_offs, readlen, buf, page); @@ -1540,7 +1539,7 @@ static int sunxi_nfc_hw_common_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { - chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + nand_read_page_op(chip, page, 0, NULL, 0); chip->pagebuf = -1; @@ -1551,9 +1550,9 @@ static int sunxi_nfc_hw_common_ecc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { - int ret, status; + int ret; - chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0, page); + nand_prog_page_begin_op(chip, page, 0, NULL, 0); chip->pagebuf = -1; @@ -1563,11 +1562,7 @@ static int sunxi_nfc_hw_common_ecc_write_oob(struct mtd_info *mtd, return ret; /* Send command to program the OOB data */ - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - - status = chip->waitfunc(mtd, chip); - - return status & NAND_STATUS_FAIL ? -EIO : 0; + return nand_prog_page_end_op(chip); } static const s32 tWB_lut[] = {6, 12, 16, 20}; diff --git a/drivers/mtd/nand/tango_nand.c b/drivers/mtd/nand/tango_nand.c index 766906f03943..97a300b46b1d 100644 --- a/drivers/mtd/nand/tango_nand.c +++ b/drivers/mtd/nand/tango_nand.c @@ -329,7 +329,7 @@ static void aux_read(struct nand_chip *chip, u8 **buf, int len, int *pos) if (!*buf) { /* skip over "len" bytes */ - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, *pos, -1); + nand_change_read_column_op(chip, *pos, NULL, 0, false); } else { tango_read_buf(mtd, *buf, len); *buf += len; @@ -344,7 +344,7 @@ static void aux_write(struct nand_chip *chip, const u8 **buf, int len, int *pos) if (!*buf) { /* skip over "len" bytes */ - chip->cmdfunc(mtd, NAND_CMD_RNDIN, *pos, -1); + nand_change_write_column_op(chip, *pos, NULL, 0, false); } else { tango_write_buf(mtd, *buf, len); *buf += len; @@ -427,7 +427,7 @@ static void raw_write(struct nand_chip *chip, const u8 *buf, const u8 *oob) static int tango_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, u8 *buf, int oob_required, int page) { - chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + nand_read_page_op(chip, page, 0, NULL, 0); raw_read(chip, buf, chip->oob_poi); return 0; } @@ -435,23 +435,15 @@ static int tango_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, static int tango_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, const u8 *buf, int oob_required, int page) { - int status; - - chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0, page); + nand_prog_page_begin_op(chip, page, 0, NULL, 0); raw_write(chip, buf, chip->oob_poi); - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - - status = chip->waitfunc(mtd, chip); - if (status & NAND_STATUS_FAIL) - return -EIO; - - return 0; + return nand_prog_page_end_op(chip); } static int tango_read_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { - chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); + nand_read_page_op(chip, page, 0, NULL, 0); raw_read(chip, NULL, chip->oob_poi); return 0; } @@ -459,11 +451,9 @@ static int tango_read_oob(struct mtd_info *mtd, struct nand_chip *chip, static int tango_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { - chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0, page); + nand_prog_page_begin_op(chip, page, 0, NULL, 0); raw_write(chip, NULL, chip->oob_poi); - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); - chip->waitfunc(mtd, chip); - return 0; + return nand_prog_page_end_op(chip); } static int oob_ecc(struct mtd_info *mtd, int idx, struct mtd_oob_region *res) diff --git a/drivers/mtd/nand/tmio_nand.c b/drivers/mtd/nand/tmio_nand.c index 84dbf32332e1..dcaa924502de 100644 --- a/drivers/mtd/nand/tmio_nand.c +++ b/drivers/mtd/nand/tmio_nand.c @@ -192,6 +192,7 @@ tmio_nand_wait(struct mtd_info *mtd, struct nand_chip *nand_chip) { struct tmio_nand *tmio = mtd_to_tmio(mtd); long timeout; + u8 status; /* enable RDYREQ interrupt */ tmio_iowrite8(0x0f, tmio->fcr + FCR_ISR); @@ -212,8 +213,8 @@ tmio_nand_wait(struct mtd_info *mtd, struct nand_chip *nand_chip) dev_warn(&tmio->dev->dev, "timeout waiting for interrupt\n"); } - nand_chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); - return nand_chip->read_byte(mtd); + nand_status_op(nand_chip, &status); + return status; } /* diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h index 749bb08c4772..fd99d5137d71 100644 --- a/include/linux/mtd/rawnand.h +++ b/include/linux/mtd/rawnand.h @@ -1316,6 +1316,35 @@ int nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, /* Reset and initialize a NAND device */ int nand_reset(struct nand_chip *chip, int chipnr); +/* NAND operation helpers */ +int nand_reset_op(struct nand_chip *chip); +int nand_readid_op(struct nand_chip *chip, u8 addr, void *buf, + unsigned int len); +int nand_status_op(struct nand_chip *chip, u8 *status); +int nand_exit_status_op(struct nand_chip *chip); +int nand_erase_op(struct nand_chip *chip, unsigned int eraseblock); +int nand_read_page_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, void *buf, unsigned int len); +int nand_change_read_column_op(struct nand_chip *chip, + unsigned int offset_in_page, void *buf, + unsigned int len, bool force_8bit); +int nand_read_oob_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, void *buf, unsigned int len); +int nand_prog_page_begin_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, const void *buf, + unsigned int len); +int nand_prog_page_end_op(struct nand_chip *chip); +int nand_prog_page_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, const void *buf, + unsigned int len); +int nand_change_write_column_op(struct nand_chip *chip, + unsigned int offset_in_page, const void *buf, + unsigned int len, bool force_8bit); +int nand_read_data_op(struct nand_chip *chip, void *buf, unsigned int len, + bool force_8bit); +int nand_write_data_op(struct nand_chip *chip, const void *buf, + unsigned int len, bool force_8bit); + /* Free resources held by the NAND device */ void nand_cleanup(struct nand_chip *chip); -- cgit v1.2.3 From 25f815f66a141436df8a4c45e5d2765272aea2ac Mon Sep 17 00:00:00 2001 From: Boris Brezillon Date: Thu, 30 Nov 2017 18:01:30 +0100 Subject: mtd: nand: force drivers to explicitly send READ/PROG commands The core currently send the READ0 and SEQIN+PAGEPROG commands in nand_do_read/write_ops(). This is inconsistent with ->read/write_oob[_raw]() hooks behavior which are expected to send these commands. There's already a flag (NAND_ECC_CUSTOM_PAGE_ACCESS) to inform the core that a specific controller wants to send the READ/SEQIN+PAGEPROG commands on its own, but it's an opt-in flag, and existing drivers are unlikely to be updated to pass it. Moreover, some controllers cannot dissociate the READ/PAGEPROG commands from the associated data transfer and ECC engine activation, and developers have to hack things in their ->cmdfunc() implementation to handle such complex cases, or have to accept the perf penalty of sending twice the same command. To address this problem we are planning on adding a new interface which is passed all information about a NAND operation (including the amount of data to transfer) and replacing all calls to ->cmdfunc() to calls to this new ->exec_op() hook. But, in order to do that, we need to have all ->cmdfunc() calls placed near their associated ->read/write_buf/byte() calls. Modify the core and relevant drivers to make NAND_ECC_CUSTOM_PAGE_ACCESS the default case, and remove this flag. Signed-off-by: Boris Brezillon [miquel.raynal@free-electrons.com: tested, fixed and rebased on nand/next] Signed-off-by: Miquel Raynal Acked-by: Masahiro Yamada --- drivers/mtd/nand/atmel/nand-controller.c | 7 ++- drivers/mtd/nand/bf5xx_nand.c | 6 +- drivers/mtd/nand/brcmnand/brcmnand.c | 13 +++- drivers/mtd/nand/cafe_nand.c | 6 +- drivers/mtd/nand/denali.c | 1 - drivers/mtd/nand/docg4.c | 12 ++-- drivers/mtd/nand/fsl_elbc_nand.c | 10 +-- drivers/mtd/nand/fsl_ifc_nand.c | 6 +- drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 31 +++++----- drivers/mtd/nand/hisi504_nand.c | 6 +- drivers/mtd/nand/lpc32xx_mlc.c | 5 +- drivers/mtd/nand/lpc32xx_slc.c | 11 +++- drivers/mtd/nand/mtk_nand.c | 22 +++---- drivers/mtd/nand/nand_base.c | 87 +++++++++++---------------- drivers/mtd/nand/nand_micron.c | 56 ++--------------- drivers/mtd/nand/omap2.c | 10 ++- drivers/mtd/nand/pxa3xx_nand.c | 6 +- drivers/mtd/nand/qcom_nandc.c | 11 ++++ drivers/mtd/nand/sh_flctl.c | 6 +- drivers/mtd/nand/sunxi_nand.c | 34 +++++++---- drivers/mtd/nand/tango_nand.c | 1 - drivers/mtd/nand/vf610_nfc.c | 6 +- drivers/staging/mt29f_spinand/mt29f_spinand.c | 5 +- include/linux/mtd/rawnand.h | 11 ---- 24 files changed, 171 insertions(+), 198 deletions(-) diff --git a/drivers/mtd/nand/atmel/nand-controller.c b/drivers/mtd/nand/atmel/nand-controller.c index e81fdd2d47b1..b2f00b398490 100644 --- a/drivers/mtd/nand/atmel/nand-controller.c +++ b/drivers/mtd/nand/atmel/nand-controller.c @@ -841,6 +841,8 @@ static int atmel_nand_pmecc_write_pg(struct nand_chip *chip, const u8 *buf, struct atmel_nand *nand = to_atmel_nand(chip); int ret; + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + ret = atmel_nand_pmecc_enable(chip, NAND_ECC_WRITE, raw); if (ret) return ret; @@ -857,7 +859,7 @@ static int atmel_nand_pmecc_write_pg(struct nand_chip *chip, const u8 *buf, atmel_nand_write_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + return nand_prog_page_end_op(chip); } static int atmel_nand_pmecc_write_page(struct mtd_info *mtd, @@ -881,6 +883,8 @@ static int atmel_nand_pmecc_read_pg(struct nand_chip *chip, u8 *buf, struct mtd_info *mtd = nand_to_mtd(chip); int ret; + nand_read_page_op(chip, page, 0, NULL, 0); + ret = atmel_nand_pmecc_enable(chip, NAND_ECC_READ, raw); if (ret) return ret; @@ -1178,7 +1182,6 @@ static int atmel_hsmc_nand_ecc_init(struct atmel_nand *nand) chip->ecc.write_page = atmel_hsmc_nand_pmecc_write_page; chip->ecc.read_page_raw = atmel_hsmc_nand_pmecc_read_page_raw; chip->ecc.write_page_raw = atmel_hsmc_nand_pmecc_write_page_raw; - chip->ecc.options |= NAND_ECC_CUSTOM_PAGE_ACCESS; return 0; } diff --git a/drivers/mtd/nand/bf5xx_nand.c b/drivers/mtd/nand/bf5xx_nand.c index 5655dca6ce43..87bbd177b3e5 100644 --- a/drivers/mtd/nand/bf5xx_nand.c +++ b/drivers/mtd/nand/bf5xx_nand.c @@ -572,6 +572,8 @@ static void bf5xx_nand_dma_write_buf(struct mtd_info *mtd, static int bf5xx_nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf, int oob_required, int page) { + nand_read_page_op(chip, page, 0, NULL, 0); + bf5xx_nand_read_buf(mtd, buf, mtd->writesize); bf5xx_nand_read_buf(mtd, chip->oob_poi, mtd->oobsize); @@ -582,10 +584,10 @@ static int bf5xx_nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required, int page) { - bf5xx_nand_write_buf(mtd, buf, mtd->writesize); + nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize); bf5xx_nand_write_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + return nand_prog_page_end_op(chip); } /* diff --git a/drivers/mtd/nand/brcmnand/brcmnand.c b/drivers/mtd/nand/brcmnand/brcmnand.c index 3f441096a14c..e6879d4d53ca 100644 --- a/drivers/mtd/nand/brcmnand/brcmnand.c +++ b/drivers/mtd/nand/brcmnand/brcmnand.c @@ -1689,7 +1689,6 @@ static int brcmstb_nand_verify_erased_page(struct mtd_info *mtd, sas = mtd->oobsize / chip->ecc.steps; /* read without ecc for verification */ - nand_read_page_op(chip, page, 0, NULL, 0); ret = chip->ecc.read_page_raw(mtd, chip, buf, true, page); if (ret) return ret; @@ -1793,6 +1792,8 @@ static int brcmnand_read_page(struct mtd_info *mtd, struct nand_chip *chip, struct brcmnand_host *host = nand_get_controller_data(chip); u8 *oob = oob_required ? (u8 *)chip->oob_poi : NULL; + nand_read_page_op(chip, page, 0, NULL, 0); + return brcmnand_read(mtd, chip, host->last_addr, mtd->writesize >> FC_SHIFT, (u32 *)buf, oob); } @@ -1804,6 +1805,8 @@ static int brcmnand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, u8 *oob = oob_required ? (u8 *)chip->oob_poi : NULL; int ret; + nand_read_page_op(chip, page, 0, NULL, 0); + brcmnand_set_ecc_enabled(host, 0); ret = brcmnand_read(mtd, chip, host->last_addr, mtd->writesize >> FC_SHIFT, (u32 *)buf, oob); @@ -1909,8 +1912,10 @@ static int brcmnand_write_page(struct mtd_info *mtd, struct nand_chip *chip, struct brcmnand_host *host = nand_get_controller_data(chip); void *oob = oob_required ? chip->oob_poi : NULL; + nand_prog_page_begin_op(chip, page, 0, NULL, 0); brcmnand_write(mtd, chip, host->last_addr, (const u32 *)buf, oob); - return 0; + + return nand_prog_page_end_op(chip); } static int brcmnand_write_page_raw(struct mtd_info *mtd, @@ -1920,10 +1925,12 @@ static int brcmnand_write_page_raw(struct mtd_info *mtd, struct brcmnand_host *host = nand_get_controller_data(chip); void *oob = oob_required ? chip->oob_poi : NULL; + nand_prog_page_begin_op(chip, page, 0, NULL, 0); brcmnand_set_ecc_enabled(host, 0); brcmnand_write(mtd, chip, host->last_addr, (const u32 *)buf, oob); brcmnand_set_ecc_enabled(host, 1); - return 0; + + return nand_prog_page_end_op(chip); } static int brcmnand_write_oob(struct mtd_info *mtd, struct nand_chip *chip, diff --git a/drivers/mtd/nand/cafe_nand.c b/drivers/mtd/nand/cafe_nand.c index 95c2cfa68b66..de36762e3058 100644 --- a/drivers/mtd/nand/cafe_nand.c +++ b/drivers/mtd/nand/cafe_nand.c @@ -383,7 +383,7 @@ static int cafe_nand_read_page(struct mtd_info *mtd, struct nand_chip *chip, cafe_readl(cafe, NAND_ECC_RESULT), cafe_readl(cafe, NAND_ECC_SYN01)); - chip->read_buf(mtd, buf, mtd->writesize); + nand_read_page_op(chip, page, 0, buf, mtd->writesize); chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); if (checkecc && cafe_readl(cafe, NAND_ECC_RESULT) & (1<<18)) { @@ -541,13 +541,13 @@ static int cafe_nand_write_page_lowlevel(struct mtd_info *mtd, { struct cafe_priv *cafe = nand_get_controller_data(chip); - chip->write_buf(mtd, buf, mtd->writesize); + nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize); chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); /* Set up ECC autogeneration */ cafe->ctl2 |= (1<<30); - return 0; + return nand_prog_page_end_op(chip); } static int cafe_nand_block_bad(struct mtd_info *mtd, loff_t ofs) diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c index d5c80d617854..47a253737bb2 100644 --- a/drivers/mtd/nand/denali.c +++ b/drivers/mtd/nand/denali.c @@ -1358,7 +1358,6 @@ int denali_init(struct denali_nand_info *denali) chip->read_buf = denali_read_buf; chip->write_buf = denali_write_buf; } - chip->ecc.options |= NAND_ECC_CUSTOM_PAGE_ACCESS; chip->ecc.read_page = denali_read_page; chip->ecc.read_page_raw = denali_read_page_raw; chip->ecc.write_page = denali_write_page; diff --git a/drivers/mtd/nand/docg4.c b/drivers/mtd/nand/docg4.c index 5a27f56dafdc..72f1327c4430 100644 --- a/drivers/mtd/nand/docg4.c +++ b/drivers/mtd/nand/docg4.c @@ -785,6 +785,8 @@ static int read_page(struct mtd_info *mtd, struct nand_chip *nand, dev_dbg(doc->dev, "%s: page %08x\n", __func__, page); + nand_read_page_op(nand, page, 0, NULL, 0); + writew(DOC_ECCCONF0_READ_MODE | DOC_ECCCONF0_ECC_ENABLE | DOC_ECCCONF0_UNKNOWN | @@ -948,7 +950,7 @@ static int docg4_erase_block(struct mtd_info *mtd, int page) } static int write_page(struct mtd_info *mtd, struct nand_chip *nand, - const uint8_t *buf, bool use_ecc) + const uint8_t *buf, int page, bool use_ecc) { struct docg4_priv *doc = nand_get_controller_data(nand); void __iomem *docptr = doc->virtadr; @@ -956,6 +958,8 @@ static int write_page(struct mtd_info *mtd, struct nand_chip *nand, dev_dbg(doc->dev, "%s...\n", __func__); + nand_prog_page_begin_op(nand, page, 0, NULL, 0); + writew(DOC_ECCCONF0_ECC_ENABLE | DOC_ECCCONF0_UNKNOWN | DOCG4_BCH_SIZE, @@ -1000,19 +1004,19 @@ static int write_page(struct mtd_info *mtd, struct nand_chip *nand, writew(0, docptr + DOC_DATAEND); write_nop(docptr); - return 0; + return nand_prog_page_end_op(nand); } static int docg4_write_page_raw(struct mtd_info *mtd, struct nand_chip *nand, const uint8_t *buf, int oob_required, int page) { - return write_page(mtd, nand, buf, false); + return write_page(mtd, nand, buf, page, false); } static int docg4_write_page(struct mtd_info *mtd, struct nand_chip *nand, const uint8_t *buf, int oob_required, int page) { - return write_page(mtd, nand, buf, true); + return write_page(mtd, nand, buf, page, true); } static int docg4_write_oob(struct mtd_info *mtd, struct nand_chip *nand, diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c index 17db2f90aa2c..8b6dcd739ecb 100644 --- a/drivers/mtd/nand/fsl_elbc_nand.c +++ b/drivers/mtd/nand/fsl_elbc_nand.c @@ -713,7 +713,7 @@ static int fsl_elbc_read_page(struct mtd_info *mtd, struct nand_chip *chip, struct fsl_lbc_ctrl *ctrl = priv->ctrl; struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = ctrl->nand; - fsl_elbc_read_buf(mtd, buf, mtd->writesize); + nand_read_page_op(chip, page, 0, buf, mtd->writesize); if (oob_required) fsl_elbc_read_buf(mtd, chip->oob_poi, mtd->oobsize); @@ -729,10 +729,10 @@ static int fsl_elbc_read_page(struct mtd_info *mtd, struct nand_chip *chip, static int fsl_elbc_write_page(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required, int page) { - fsl_elbc_write_buf(mtd, buf, mtd->writesize); + nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize); fsl_elbc_write_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + return nand_prog_page_end_op(chip); } /* ECC will be calculated automatically, and errors will be detected in @@ -742,10 +742,10 @@ static int fsl_elbc_write_subpage(struct mtd_info *mtd, struct nand_chip *chip, uint32_t offset, uint32_t data_len, const uint8_t *buf, int oob_required, int page) { + nand_prog_page_begin_op(chip, page, 0, NULL, 0); fsl_elbc_write_buf(mtd, buf, mtd->writesize); fsl_elbc_write_buf(mtd, chip->oob_poi, mtd->oobsize); - - return 0; + return nand_prog_page_end_op(chip); } static int fsl_elbc_chip_init(struct fsl_elbc_mtd *priv) diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c index bbdd68a54d68..4872a7ba6503 100644 --- a/drivers/mtd/nand/fsl_ifc_nand.c +++ b/drivers/mtd/nand/fsl_ifc_nand.c @@ -688,7 +688,7 @@ static int fsl_ifc_read_page(struct mtd_info *mtd, struct nand_chip *chip, struct fsl_ifc_ctrl *ctrl = priv->ctrl; struct fsl_ifc_nand_ctrl *nctrl = ifc_nand_ctrl; - fsl_ifc_read_buf(mtd, buf, mtd->writesize); + nand_read_page_op(chip, page, 0, buf, mtd->writesize); if (oob_required) fsl_ifc_read_buf(mtd, chip->oob_poi, mtd->oobsize); @@ -711,10 +711,10 @@ static int fsl_ifc_read_page(struct mtd_info *mtd, struct nand_chip *chip, static int fsl_ifc_write_page(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required, int page) { - fsl_ifc_write_buf(mtd, buf, mtd->writesize); + nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize); fsl_ifc_write_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + return nand_prog_page_end_op(chip); } static int fsl_ifc_chip_init_tail(struct mtd_info *mtd) diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c index 63a425ced4cd..3c3f3f58fdcb 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c @@ -1043,6 +1043,8 @@ static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip, unsigned int max_bitflips = 0; int ret; + nand_read_page_op(chip, page, 0, NULL, 0); + dev_dbg(this->dev, "page number is : %d\n", page); ret = read_page_prepare(this, buf, nfc_geo->payload_size, this->payload_virt, this->payload_phys, @@ -1220,12 +1222,12 @@ static int gpmi_ecc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, meta = geo->metadata_size; if (first) { col = meta + (size + ecc_parity_size) * first; - nand_change_read_column_op(chip, col, NULL, 0, false); - meta = 0; buf = buf + first * size; } + nand_read_page_op(chip, page, col, NULL, 0); + /* Save the old environment */ r1_old = r1_new = readl(bch_regs + HW_BCH_FLASH0LAYOUT0); r2_old = r2_new = readl(bch_regs + HW_BCH_FLASH0LAYOUT1); @@ -1277,6 +1279,9 @@ static int gpmi_ecc_write_page(struct mtd_info *mtd, struct nand_chip *chip, int ret; dev_dbg(this->dev, "ecc write page.\n"); + + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + if (this->swap_block_mark) { /* * If control arrives here, we're doing block mark swapping. @@ -1338,7 +1343,10 @@ exit_auxiliary: payload_virt, payload_phys); } - return 0; + if (ret) + return ret; + + return nand_prog_page_end_op(chip); } /* @@ -1472,8 +1480,8 @@ static int gpmi_ecc_read_page_raw(struct mtd_info *mtd, uint8_t *oob = chip->oob_poi; int step; - chip->read_buf(mtd, tmp_buf, - mtd->writesize + mtd->oobsize); + nand_read_page_op(chip, page, 0, tmp_buf, + mtd->writesize + mtd->oobsize); /* * If required, swap the bad block marker and the data stored in the @@ -1609,24 +1617,19 @@ static int gpmi_ecc_write_page_raw(struct mtd_info *mtd, if (this->swap_block_mark) swap(tmp_buf[0], tmp_buf[mtd->writesize]); - chip->write_buf(mtd, tmp_buf, mtd->writesize + mtd->oobsize); - - return 0; + return nand_prog_page_op(chip, page, 0, tmp_buf, + mtd->writesize + mtd->oobsize); } static int gpmi_ecc_read_oob_raw(struct mtd_info *mtd, struct nand_chip *chip, int page) { - nand_read_page_op(chip, page, 0, NULL, 0); - return gpmi_ecc_read_page_raw(mtd, chip, NULL, 1, page); } static int gpmi_ecc_write_oob_raw(struct mtd_info *mtd, struct nand_chip *chip, int page) { - nand_prog_page_begin_op(chip, page, 0, NULL, 0); - return gpmi_ecc_write_page_raw(mtd, chip, NULL, 1, page); } @@ -1798,9 +1801,7 @@ static int mx23_write_transcription_stamp(struct gpmi_nand_data *this) /* Write the first page of the current stride. */ dev_dbg(dev, "Writing an NCB fingerprint in page 0x%x\n", page); - nand_prog_page_begin_op(chip, page, 0, NULL, 0); - chip->ecc.write_page_raw(mtd, chip, buffer, 0, page); - status = nand_prog_page_end_op(chip); + status = chip->ecc.write_page_raw(mtd, chip, buffer, 0, page); if (status) dev_err(dev, "[%s] Write failed.\n", __func__); } diff --git a/drivers/mtd/nand/hisi504_nand.c b/drivers/mtd/nand/hisi504_nand.c index 184d765c8bbe..cb862793ab6d 100644 --- a/drivers/mtd/nand/hisi504_nand.c +++ b/drivers/mtd/nand/hisi504_nand.c @@ -544,7 +544,7 @@ static int hisi_nand_read_page_hwecc(struct mtd_info *mtd, int max_bitflips = 0, stat = 0, stat_max = 0, status_ecc; int stat_1, stat_2; - chip->read_buf(mtd, buf, mtd->writesize); + nand_read_page_op(chip, page, 0, buf, mtd->writesize); chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); /* errors which can not be corrected by ECC */ @@ -589,11 +589,11 @@ static int hisi_nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required, int page) { - chip->write_buf(mtd, buf, mtd->writesize); + nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize); if (oob_required) chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + return nand_prog_page_end_op(chip); } static void hisi_nfc_host_init(struct hinfc_host *host) diff --git a/drivers/mtd/nand/lpc32xx_mlc.c b/drivers/mtd/nand/lpc32xx_mlc.c index 31cb3b2967b9..e357948a7505 100644 --- a/drivers/mtd/nand/lpc32xx_mlc.c +++ b/drivers/mtd/nand/lpc32xx_mlc.c @@ -522,6 +522,8 @@ static int lpc32xx_write_page_lowlevel(struct mtd_info *mtd, memcpy(dma_buf, buf, mtd->writesize); } + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + for (i = 0; i < host->mlcsubpages; i++) { /* Start Encode */ writeb(0x00, MLC_ECC_ENC_REG(host->io_base)); @@ -550,7 +552,8 @@ static int lpc32xx_write_page_lowlevel(struct mtd_info *mtd, /* Wait for Controller Ready */ lpc32xx_waitfunc_controller(mtd, chip); } - return 0; + + return nand_prog_page_end_op(chip); } static int lpc32xx_read_oob(struct mtd_info *mtd, struct nand_chip *chip, diff --git a/drivers/mtd/nand/lpc32xx_slc.c b/drivers/mtd/nand/lpc32xx_slc.c index 2b96c281b1a2..5f7cc6da0a7f 100644 --- a/drivers/mtd/nand/lpc32xx_slc.c +++ b/drivers/mtd/nand/lpc32xx_slc.c @@ -686,6 +686,8 @@ static int lpc32xx_nand_write_page_syndrome(struct mtd_info *mtd, uint8_t *pb; int error; + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + /* Write data, calculate ECC on outbound data */ error = lpc32xx_xfer(mtd, (uint8_t *)buf, chip->ecc.steps, 0); if (error) @@ -704,7 +706,8 @@ static int lpc32xx_nand_write_page_syndrome(struct mtd_info *mtd, /* Write ECC data to device */ chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + + return nand_prog_page_end_op(chip); } /* @@ -717,9 +720,11 @@ static int lpc32xx_nand_write_page_raw_syndrome(struct mtd_info *mtd, int oob_required, int page) { /* Raw writes can just use the FIFO interface */ - chip->write_buf(mtd, buf, chip->ecc.size * chip->ecc.steps); + nand_prog_page_begin_op(chip, page, 0, buf, + chip->ecc.size * chip->ecc.steps); chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + + return nand_prog_page_end_op(chip); } static int lpc32xx_nand_dma_setup(struct lpc32xx_nand_host *host) diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/mtk_nand.c index 9c4adaf9331b..5d76be451596 100644 --- a/drivers/mtd/nand/mtk_nand.c +++ b/drivers/mtd/nand/mtk_nand.c @@ -761,6 +761,8 @@ static int mtk_nfc_write_page(struct mtd_info *mtd, struct nand_chip *chip, u32 reg; int ret; + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + if (!raw) { /* OOB => FDM: from register, ECC: from HW */ reg = nfi_readw(nfc, NFI_CNFG) | CNFG_AUTO_FMT_EN; @@ -794,7 +796,10 @@ static int mtk_nfc_write_page(struct mtd_info *mtd, struct nand_chip *chip, if (!raw) mtk_ecc_disable(nfc->ecc); - return ret; + if (ret) + return ret; + + return nand_prog_page_end_op(chip); } static int mtk_nfc_write_page_hwecc(struct mtd_info *mtd, @@ -832,15 +837,7 @@ static int mtk_nfc_write_subpage_hwecc(struct mtd_info *mtd, static int mtk_nfc_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip, int page) { - int ret; - - nand_prog_page_begin_op(chip, page, 0, NULL, 0); - - ret = mtk_nfc_write_page_raw(mtd, chip, NULL, 1, page); - if (ret < 0) - return -EIO; - - return nand_prog_page_end_op(chip); + return mtk_nfc_write_page_raw(mtd, chip, NULL, 1, page); } static int mtk_nfc_update_ecc_stats(struct mtd_info *mtd, u8 *buf, u32 sectors) @@ -889,8 +886,7 @@ static int mtk_nfc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, len = sectors * chip->ecc.size + (raw ? sectors * spare : 0); buf = bufpoi + start * chip->ecc.size; - if (column != 0) - nand_change_read_column_op(chip, column, NULL, 0, false); + nand_read_page_op(chip, page, column, NULL, 0); addr = dma_map_single(nfc->dev, buf, len, DMA_FROM_DEVICE); rc = dma_mapping_error(nfc->dev, addr); @@ -1013,8 +1009,6 @@ static int mtk_nfc_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, static int mtk_nfc_read_oob_std(struct mtd_info *mtd, struct nand_chip *chip, int page) { - nand_read_page_op(chip, page, 0, NULL, 0); - return mtk_nfc_read_page_raw(mtd, chip, NULL, 1, page); } diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 539132ef0095..e3bf33bc1fb6 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -1940,7 +1940,7 @@ int nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, { int ret; - ret = nand_read_data_op(chip, buf, mtd->writesize, false); + ret = nand_read_page_op(chip, page, 0, buf, mtd->writesize); if (ret) return ret; @@ -1974,6 +1974,10 @@ static int nand_read_page_raw_syndrome(struct mtd_info *mtd, uint8_t *oob = chip->oob_poi; int steps, size, ret; + ret = nand_read_page_op(chip, page, 0, NULL, 0); + if (ret) + return ret; + for (steps = chip->ecc.steps; steps > 0; steps--) { ret = nand_read_data_op(chip, buf, eccsize, false); if (ret) @@ -2096,11 +2100,8 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, data_col_addr = start_step * chip->ecc.size; /* If we read not a page aligned data */ - if (data_col_addr != 0) - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, data_col_addr, -1); - p = bufpoi + data_col_addr; - ret = nand_read_data_op(chip, p, datafrag_len, false); + ret = nand_read_page_op(chip, page, data_col_addr, p, datafrag_len); if (ret) return ret; @@ -2198,6 +2199,10 @@ static int nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *ecc_code = chip->buffers->ecccode; unsigned int max_bitflips = 0; + ret = nand_read_page_op(chip, page, 0, NULL, 0); + if (ret) + return ret; + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { chip->ecc.hwctl(mtd, NAND_ECC_READ); @@ -2335,6 +2340,10 @@ static int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *oob = chip->oob_poi; unsigned int max_bitflips = 0; + ret = nand_read_page_op(chip, page, 0, NULL, 0); + if (ret) + return ret; + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { int stat; @@ -2517,12 +2526,6 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, __func__, buf); read_retry: - if (nand_standard_page_accessors(&chip->ecc)) { - ret = nand_read_page_op(chip, page, 0, NULL, 0); - if (ret) - break; - } - /* * Now read the page into the buffer. Absent an error, * the read methods return max bitflips per ecc step. @@ -2978,7 +2981,7 @@ int nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, { int ret; - ret = nand_write_data_op(chip, buf, mtd->writesize, false); + ret = nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize); if (ret) return ret; @@ -2989,7 +2992,7 @@ int nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, return ret; } - return 0; + return nand_prog_page_end_op(chip); } EXPORT_SYMBOL(nand_write_page_raw); @@ -3013,6 +3016,10 @@ static int nand_write_page_raw_syndrome(struct mtd_info *mtd, uint8_t *oob = chip->oob_poi; int steps, size, ret; + ret = nand_prog_page_begin_op(chip, page, 0, NULL, 0); + if (ret) + return ret; + for (steps = chip->ecc.steps; steps > 0; steps--) { ret = nand_write_data_op(chip, buf, eccsize, false); if (ret) @@ -3052,7 +3059,7 @@ static int nand_write_page_raw_syndrome(struct mtd_info *mtd, return ret; } - return 0; + return nand_prog_page_end_op(chip); } /** * nand_write_page_swecc - [REPLACEABLE] software ECC based page write function @@ -3102,6 +3109,10 @@ static int nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *ecc_calc = chip->buffers->ecccalc; const uint8_t *p = buf; + ret = nand_prog_page_begin_op(chip, page, 0, NULL, 0); + if (ret) + return ret; + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { chip->ecc.hwctl(mtd, NAND_ECC_WRITE); @@ -3121,7 +3132,7 @@ static int nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, if (ret) return ret; - return 0; + return nand_prog_page_end_op(chip); } @@ -3150,6 +3161,10 @@ static int nand_write_subpage_hwecc(struct mtd_info *mtd, int oob_bytes = mtd->oobsize / ecc_steps; int step, ret; + ret = nand_prog_page_begin_op(chip, page, 0, NULL, 0); + if (ret) + return ret; + for (step = 0; step < ecc_steps; step++) { /* configure controller for WRITE access */ chip->ecc.hwctl(mtd, NAND_ECC_WRITE); @@ -3188,7 +3203,7 @@ static int nand_write_subpage_hwecc(struct mtd_info *mtd, if (ret) return ret; - return 0; + return nand_prog_page_end_op(chip); } @@ -3215,6 +3230,10 @@ static int nand_write_page_syndrome(struct mtd_info *mtd, uint8_t *oob = chip->oob_poi; int ret; + ret = nand_prog_page_begin_op(chip, page, 0, NULL, 0); + if (ret) + return ret; + for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { chip->ecc.hwctl(mtd, NAND_ECC_WRITE); @@ -3257,7 +3276,7 @@ static int nand_write_page_syndrome(struct mtd_info *mtd, return ret; } - return 0; + return nand_prog_page_end_op(chip); } /** @@ -3283,12 +3302,6 @@ static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip, else subpage = 0; - if (nand_standard_page_accessors(&chip->ecc)) { - status = nand_prog_page_begin_op(chip, page, 0, NULL, 0); - if (status) - return status; - } - if (unlikely(raw)) status = chip->ecc.write_page_raw(mtd, chip, buf, oob_required, page); @@ -3302,9 +3315,6 @@ static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip, if (status < 0) return status; - if (nand_standard_page_accessors(&chip->ecc)) - return nand_prog_page_end_op(chip); - return 0; } @@ -5290,26 +5300,6 @@ static bool nand_ecc_strength_good(struct mtd_info *mtd) return corr >= ds_corr && ecc->strength >= chip->ecc_strength_ds; } -static bool invalid_ecc_page_accessors(struct nand_chip *chip) -{ - struct nand_ecc_ctrl *ecc = &chip->ecc; - - if (nand_standard_page_accessors(ecc)) - return false; - - /* - * NAND_ECC_CUSTOM_PAGE_ACCESS flag is set, make sure the NAND - * controller driver implements all the page accessors because - * default helpers are not suitable when the core does not - * send the READ0/PAGEPROG commands. - */ - return (!ecc->read_page || !ecc->write_page || - !ecc->read_page_raw || !ecc->write_page_raw || - (NAND_HAS_SUBPAGE_READ(chip) && !ecc->read_subpage) || - (NAND_HAS_SUBPAGE_WRITE(chip) && !ecc->write_subpage && - ecc->hwctl && ecc->calculate)); -} - /** * nand_scan_tail - [NAND Interface] Scan for the NAND device * @mtd: MTD device structure @@ -5331,11 +5321,6 @@ int nand_scan_tail(struct mtd_info *mtd) return -EINVAL; } - if (invalid_ecc_page_accessors(chip)) { - pr_err("Invalid ECC page accessors setup\n"); - return -EINVAL; - } - if (!(chip->options & NAND_OWN_BUFFERS)) { nbuf = kzalloc(sizeof(*nbuf), GFP_KERNEL); if (!nbuf) diff --git a/drivers/mtd/nand/nand_micron.c b/drivers/mtd/nand/nand_micron.c index bf2dc23e1c32..02e109ae73f1 100644 --- a/drivers/mtd/nand/nand_micron.c +++ b/drivers/mtd/nand/nand_micron.c @@ -149,7 +149,10 @@ micron_nand_read_page_on_die_ecc(struct mtd_info *mtd, struct nand_chip *chip, else if (status & NAND_STATUS_WRITE_RECOMMENDED) max_bitflips = chip->ecc.strength; - ret = nand_read_page_raw(mtd, chip, buf, oob_required, page); + ret = nand_read_data_op(chip, buf, mtd->writesize, false); + if (!ret && oob_required) + ret = nand_read_data_op(chip, chip->oob_poi, mtd->oobsize, + false); out: micron_nand_on_die_ecc_setup(chip, false); @@ -168,56 +171,12 @@ micron_nand_write_page_on_die_ecc(struct mtd_info *mtd, struct nand_chip *chip, if (ret) return ret; - ret = nand_prog_page_begin_op(chip, page, 0, NULL, 0); - if (ret) - goto out; - ret = nand_write_page_raw(mtd, chip, buf, oob_required, page); - if (ret) - return ret; - - ret = nand_prog_page_end_op(chip); - -out: micron_nand_on_die_ecc_setup(chip, false); return ret; } -static int -micron_nand_read_page_raw_on_die_ecc(struct mtd_info *mtd, - struct nand_chip *chip, - uint8_t *buf, int oob_required, - int page) -{ - int ret; - - ret = nand_read_page_op(chip, page, 0, NULL, 0); - if (ret) - return ret; - - return nand_read_page_raw(mtd, chip, buf, oob_required, page); -} - -static int -micron_nand_write_page_raw_on_die_ecc(struct mtd_info *mtd, - struct nand_chip *chip, - const uint8_t *buf, int oob_required, - int page) -{ - int ret; - - ret = nand_prog_page_begin_op(chip, page, 0, NULL, 0); - if (ret) - return ret; - - ret = nand_write_page_raw(mtd, chip, buf, oob_required, page); - if (ret) - return ret; - - return nand_prog_page_end_op(chip); -} - enum { /* The NAND flash doesn't support on-die ECC */ MICRON_ON_DIE_UNSUPPORTED, @@ -310,17 +269,14 @@ static int micron_nand_init(struct nand_chip *chip) return -EINVAL; } - chip->ecc.options = NAND_ECC_CUSTOM_PAGE_ACCESS; chip->ecc.bytes = 8; chip->ecc.size = 512; chip->ecc.strength = 4; chip->ecc.algo = NAND_ECC_BCH; chip->ecc.read_page = micron_nand_read_page_on_die_ecc; chip->ecc.write_page = micron_nand_write_page_on_die_ecc; - chip->ecc.read_page_raw = - micron_nand_read_page_raw_on_die_ecc; - chip->ecc.write_page_raw = - micron_nand_write_page_raw_on_die_ecc; + chip->ecc.read_page_raw = nand_read_page_raw; + chip->ecc.write_page_raw = nand_write_page_raw; mtd_set_ooblayout(mtd, µn_nand_on_die_ooblayout_ops); } diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index 6e1b209cd5a7..5cb4db6f88e3 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -1532,6 +1532,8 @@ static int omap_write_page_bch(struct mtd_info *mtd, struct nand_chip *chip, int ret; uint8_t *ecc_calc = chip->buffers->ecccalc; + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + /* Enable GPMC ecc engine */ chip->ecc.hwctl(mtd, NAND_ECC_WRITE); @@ -1548,7 +1550,8 @@ static int omap_write_page_bch(struct mtd_info *mtd, struct nand_chip *chip, /* Write ecc vector to OOB area */ chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + + return nand_prog_page_end_op(chip); } /** @@ -1582,6 +1585,7 @@ static int omap_write_subpage_bch(struct mtd_info *mtd, * ECC is calculated for all subpages but we choose * only what we want. */ + nand_prog_page_begin_op(chip, page, 0, NULL, 0); /* Enable GPMC ECC engine */ chip->ecc.hwctl(mtd, NAND_ECC_WRITE); @@ -1614,7 +1618,7 @@ static int omap_write_subpage_bch(struct mtd_info *mtd, /* write OOB buffer to NAND device */ chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + return nand_prog_page_end_op(chip); } /** @@ -1640,6 +1644,8 @@ static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip, int stat, ret; unsigned int max_bitflips = 0; + nand_read_page_op(chip, page, 0, NULL, 0); + /* Enable GPMC ecc engine */ chip->ecc.hwctl(mtd, NAND_ECC_READ); diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c index 28bcdf64c1fc..021374fe59dc 100644 --- a/drivers/mtd/nand/pxa3xx_nand.c +++ b/drivers/mtd/nand/pxa3xx_nand.c @@ -1348,10 +1348,10 @@ static int pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required, int page) { - chip->write_buf(mtd, buf, mtd->writesize); + nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize); chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + return nand_prog_page_end_op(chip); } static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd, @@ -1361,7 +1361,7 @@ static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd, struct pxa3xx_nand_host *host = nand_get_controller_data(chip); struct pxa3xx_nand_info *info = host->info_data; - chip->read_buf(mtd, buf, mtd->writesize); + nand_read_page_op(chip, page, 0, buf, mtd->writesize); chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); if (info->retcode == ERR_CORERR && info->use_ecc) { diff --git a/drivers/mtd/nand/qcom_nandc.c b/drivers/mtd/nand/qcom_nandc.c index e34313ecd903..245d0f39e0aa 100644 --- a/drivers/mtd/nand/qcom_nandc.c +++ b/drivers/mtd/nand/qcom_nandc.c @@ -1725,6 +1725,7 @@ static int qcom_nandc_read_page(struct mtd_info *mtd, struct nand_chip *chip, u8 *data_buf, *oob_buf = NULL; int ret; + nand_read_page_op(chip, page, 0, NULL, 0); data_buf = buf; oob_buf = oob_required ? chip->oob_poi : NULL; @@ -1750,6 +1751,7 @@ static int qcom_nandc_read_page_raw(struct mtd_info *mtd, int i, ret; int read_loc; + nand_read_page_op(chip, page, 0, NULL, 0); data_buf = buf; oob_buf = chip->oob_poi; @@ -1850,6 +1852,8 @@ static int qcom_nandc_write_page(struct mtd_info *mtd, struct nand_chip *chip, u8 *data_buf, *oob_buf; int i, ret; + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + clear_read_regs(nandc); clear_bam_transaction(nandc); @@ -1902,6 +1906,9 @@ static int qcom_nandc_write_page(struct mtd_info *mtd, struct nand_chip *chip, free_descs(nandc); + if (!ret) + ret = nand_prog_page_end_op(chip); + return ret; } @@ -1916,6 +1923,7 @@ static int qcom_nandc_write_page_raw(struct mtd_info *mtd, u8 *data_buf, *oob_buf; int i, ret; + nand_prog_page_begin_op(chip, page, 0, NULL, 0); clear_read_regs(nandc); clear_bam_transaction(nandc); @@ -1970,6 +1978,9 @@ static int qcom_nandc_write_page_raw(struct mtd_info *mtd, free_descs(nandc); + if (!ret) + ret = nand_prog_page_end_op(chip); + return ret; } diff --git a/drivers/mtd/nand/sh_flctl.c b/drivers/mtd/nand/sh_flctl.c index 3c5008a4f5f3..c4e7755448e6 100644 --- a/drivers/mtd/nand/sh_flctl.c +++ b/drivers/mtd/nand/sh_flctl.c @@ -614,7 +614,7 @@ static void set_cmd_regs(struct mtd_info *mtd, uint32_t cmd, uint32_t flcmcdr_va static int flctl_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf, int oob_required, int page) { - chip->read_buf(mtd, buf, mtd->writesize); + nand_read_page_op(chip, page, 0, buf, mtd->writesize); if (oob_required) chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); return 0; @@ -624,9 +624,9 @@ static int flctl_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required, int page) { - chip->write_buf(mtd, buf, mtd->writesize); + nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize); chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); - return 0; + return nand_prog_page_end_op(chip); } static void execmd_read_page_sector(struct mtd_info *mtd, int page_addr) diff --git a/drivers/mtd/nand/sunxi_nand.c b/drivers/mtd/nand/sunxi_nand.c index da5cc36f4c30..5c176dee821e 100644 --- a/drivers/mtd/nand/sunxi_nand.c +++ b/drivers/mtd/nand/sunxi_nand.c @@ -1245,6 +1245,8 @@ static int sunxi_nfc_hw_ecc_read_page(struct mtd_info *mtd, int ret, i, cur_off = 0; bool raw_mode = false; + nand_read_page_op(chip, page, 0, NULL, 0); + sunxi_nfc_hw_ecc_enable(mtd); for (i = 0; i < ecc->steps; i++) { @@ -1278,14 +1280,14 @@ static int sunxi_nfc_hw_ecc_read_page_dma(struct mtd_info *mtd, { int ret; + nand_read_page_op(chip, page, 0, NULL, 0); + ret = sunxi_nfc_hw_ecc_read_chunks_dma(mtd, buf, oob_required, page, chip->ecc.steps); if (ret >= 0) return ret; /* Fallback to PIO mode */ - nand_change_read_column_op(chip, 0, NULL, 0, false); - return sunxi_nfc_hw_ecc_read_page(mtd, chip, buf, oob_required, page); } @@ -1298,6 +1300,8 @@ static int sunxi_nfc_hw_ecc_read_subpage(struct mtd_info *mtd, int ret, i, cur_off = 0; unsigned int max_bitflips = 0; + nand_read_page_op(chip, page, 0, NULL, 0); + sunxi_nfc_hw_ecc_enable(mtd); for (i = data_offs / ecc->size; @@ -1329,13 +1333,13 @@ static int sunxi_nfc_hw_ecc_read_subpage_dma(struct mtd_info *mtd, int nchunks = DIV_ROUND_UP(data_offs + readlen, chip->ecc.size); int ret; + nand_read_page_op(chip, page, 0, NULL, 0); + ret = sunxi_nfc_hw_ecc_read_chunks_dma(mtd, buf, false, page, nchunks); if (ret >= 0) return ret; /* Fallback to PIO mode */ - nand_change_read_column_op(chip, 0, NULL, 0, false); - return sunxi_nfc_hw_ecc_read_subpage(mtd, chip, data_offs, readlen, buf, page); } @@ -1348,6 +1352,8 @@ static int sunxi_nfc_hw_ecc_write_page(struct mtd_info *mtd, struct nand_ecc_ctrl *ecc = &chip->ecc; int ret, i, cur_off = 0; + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + sunxi_nfc_hw_ecc_enable(mtd); for (i = 0; i < ecc->steps; i++) { @@ -1369,7 +1375,7 @@ static int sunxi_nfc_hw_ecc_write_page(struct mtd_info *mtd, sunxi_nfc_hw_ecc_disable(mtd); - return 0; + return nand_prog_page_end_op(chip); } static int sunxi_nfc_hw_ecc_write_subpage(struct mtd_info *mtd, @@ -1381,6 +1387,8 @@ static int sunxi_nfc_hw_ecc_write_subpage(struct mtd_info *mtd, struct nand_ecc_ctrl *ecc = &chip->ecc; int ret, i, cur_off = 0; + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + sunxi_nfc_hw_ecc_enable(mtd); for (i = data_offs / ecc->size; @@ -1399,7 +1407,7 @@ static int sunxi_nfc_hw_ecc_write_subpage(struct mtd_info *mtd, sunxi_nfc_hw_ecc_disable(mtd); - return 0; + return nand_prog_page_end_op(chip); } static int sunxi_nfc_hw_ecc_write_page_dma(struct mtd_info *mtd, @@ -1429,6 +1437,8 @@ static int sunxi_nfc_hw_ecc_write_page_dma(struct mtd_info *mtd, sunxi_nfc_hw_ecc_set_prot_oob_bytes(mtd, oob, i, !i, page); } + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + sunxi_nfc_hw_ecc_enable(mtd); sunxi_nfc_randomizer_config(mtd, page, false); sunxi_nfc_randomizer_enable(mtd); @@ -1459,7 +1469,7 @@ static int sunxi_nfc_hw_ecc_write_page_dma(struct mtd_info *mtd, sunxi_nfc_hw_ecc_write_extra_oob(mtd, chip->oob_poi, NULL, page); - return 0; + return nand_prog_page_end_op(chip); pio_fallback: return sunxi_nfc_hw_ecc_write_page(mtd, chip, buf, oob_required, page); @@ -1475,6 +1485,8 @@ static int sunxi_nfc_hw_syndrome_ecc_read_page(struct mtd_info *mtd, int ret, i, cur_off = 0; bool raw_mode = false; + nand_read_page_op(chip, page, 0, NULL, 0); + sunxi_nfc_hw_ecc_enable(mtd); for (i = 0; i < ecc->steps; i++) { @@ -1511,6 +1523,8 @@ static int sunxi_nfc_hw_syndrome_ecc_write_page(struct mtd_info *mtd, struct nand_ecc_ctrl *ecc = &chip->ecc; int ret, i, cur_off = 0; + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + sunxi_nfc_hw_ecc_enable(mtd); for (i = 0; i < ecc->steps; i++) { @@ -1532,15 +1546,13 @@ static int sunxi_nfc_hw_syndrome_ecc_write_page(struct mtd_info *mtd, sunxi_nfc_hw_ecc_disable(mtd); - return 0; + return nand_prog_page_end_op(chip); } static int sunxi_nfc_hw_common_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { - nand_read_page_op(chip, page, 0, NULL, 0); - chip->pagebuf = -1; return chip->ecc.read_page(mtd, chip, chip->buffers->databuf, 1, page); @@ -1552,8 +1564,6 @@ static int sunxi_nfc_hw_common_ecc_write_oob(struct mtd_info *mtd, { int ret; - nand_prog_page_begin_op(chip, page, 0, NULL, 0); - chip->pagebuf = -1; memset(chip->buffers->databuf, 0xff, mtd->writesize); diff --git a/drivers/mtd/nand/tango_nand.c b/drivers/mtd/nand/tango_nand.c index 97a300b46b1d..c5bee00b7f5e 100644 --- a/drivers/mtd/nand/tango_nand.c +++ b/drivers/mtd/nand/tango_nand.c @@ -580,7 +580,6 @@ static int chip_init(struct device *dev, struct device_node *np) ecc->write_page = tango_write_page; ecc->read_oob = tango_read_oob; ecc->write_oob = tango_write_oob; - ecc->options = NAND_ECC_CUSTOM_PAGE_ACCESS; err = nand_scan_tail(mtd); if (err) diff --git a/drivers/mtd/nand/vf610_nfc.c b/drivers/mtd/nand/vf610_nfc.c index 8037d4b48a05..80d31a58e558 100644 --- a/drivers/mtd/nand/vf610_nfc.c +++ b/drivers/mtd/nand/vf610_nfc.c @@ -560,7 +560,7 @@ static int vf610_nfc_read_page(struct mtd_info *mtd, struct nand_chip *chip, int eccsize = chip->ecc.size; int stat; - vf610_nfc_read_buf(mtd, buf, eccsize); + nand_read_page_op(chip, page, 0, buf, eccsize); if (oob_required) vf610_nfc_read_buf(mtd, chip->oob_poi, mtd->oobsize); @@ -580,7 +580,7 @@ static int vf610_nfc_write_page(struct mtd_info *mtd, struct nand_chip *chip, { struct vf610_nfc *nfc = mtd_to_nfc(mtd); - vf610_nfc_write_buf(mtd, buf, mtd->writesize); + nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize); if (oob_required) vf610_nfc_write_buf(mtd, chip->oob_poi, mtd->oobsize); @@ -588,7 +588,7 @@ static int vf610_nfc_write_page(struct mtd_info *mtd, struct nand_chip *chip, nfc->use_hw_ecc = true; nfc->write_sz = mtd->writesize + mtd->oobsize; - return 0; + return nand_prog_page_end_op(chip); } static const struct of_device_id vf610_nfc_dt_ids[] = { diff --git a/drivers/staging/mt29f_spinand/mt29f_spinand.c b/drivers/staging/mt29f_spinand/mt29f_spinand.c index 87595c594b12..264ad362d858 100644 --- a/drivers/staging/mt29f_spinand/mt29f_spinand.c +++ b/drivers/staging/mt29f_spinand/mt29f_spinand.c @@ -637,8 +637,7 @@ static int spinand_write_page_hwecc(struct mtd_info *mtd, int eccsteps = chip->ecc.steps; enable_hw_ecc = 1; - chip->write_buf(mtd, p, eccsize * eccsteps); - return 0; + return nand_prog_page_op(chip, page, 0, p, eccsize * eccsteps); } static int spinand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, @@ -653,7 +652,7 @@ static int spinand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, enable_read_hw_ecc = 1; - chip->read_buf(mtd, p, eccsize * eccsteps); + nand_read_page_op(chip, page, 0, p, eccsize * eccsteps); if (oob_required) chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h index fd99d5137d71..e6810f0b8f9e 100644 --- a/include/linux/mtd/rawnand.h +++ b/include/linux/mtd/rawnand.h @@ -133,12 +133,6 @@ enum nand_ecc_algo { */ #define NAND_ECC_GENERIC_ERASED_CHECK BIT(0) #define NAND_ECC_MAXIMIZE BIT(1) -/* - * If your controller already sends the required NAND commands when - * reading or writing a page, then the framework is not supposed to - * send READ0 and SEQIN/PAGEPROG respectively. - */ -#define NAND_ECC_CUSTOM_PAGE_ACCESS BIT(2) /* Bit mask for flags passed to do_nand_read_ecc */ #define NAND_GET_DEVICE 0x80 @@ -602,11 +596,6 @@ struct nand_ecc_ctrl { int page); }; -static inline int nand_standard_page_accessors(struct nand_ecc_ctrl *ecc) -{ - return !(ecc->options & NAND_ECC_CUSTOM_PAGE_ACCESS); -} - /** * struct nand_buffers - buffer structure for read/write * @ecccalc: buffer pointer for calculated ECC, size is oobsize. -- cgit v1.2.3 From 17fa8044188c152e8a3b9493f8b8054cacbfb9ba Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Thu, 30 Nov 2017 18:01:31 +0100 Subject: mtd: nand: provide valid ->data_interface during NAND detection Right now, the chip->data_interface field is populated in nand_scan_tail(), so after the whole NAND detection has taken place. This is fine because these timings are not yet used by the core so early in the probe process, but the situation is about to change with the introduction of ->exec_op(). Also, by convention, nand_scan_ident() is not supposed to allocate resources, only nand_scan_tail() can, so this prevent us from allocating and initializing the data_interface object in nand_scan_ident(). In order to solve this problem, directly embed a data_interface object in nand_chip so that we don't have to allocate it, and initialize it to ONFI SDR mode 0 at the very beginning of nand_scan_ident(). Signed-off-by: Miquel Raynal Signed-off-by: Boris Brezillon --- drivers/mtd/nand/nand_base.c | 46 ++++++++++++++++++----------------------- drivers/mtd/nand/nand_timings.c | 21 +++++-------------- include/linux/mtd/rawnand.h | 7 ++----- 3 files changed, 27 insertions(+), 47 deletions(-) diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index e3bf33bc1fb6..215c52a3b9ad 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -816,8 +816,8 @@ static void nand_ccs_delay(struct nand_chip *chip) * Wait tCCS_min if it is correctly defined, otherwise wait 500ns * (which should be safe for all NANDs). */ - if (chip->data_interface && chip->data_interface->timings.sdr.tCCS_min) - ndelay(chip->data_interface->timings.sdr.tCCS_min / 1000); + if (chip->setup_data_interface) + ndelay(chip->data_interface.timings.sdr.tCCS_min / 1000); else ndelay(500); } @@ -1112,7 +1112,6 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip) static int nand_reset_data_interface(struct nand_chip *chip, int chipnr) { struct mtd_info *mtd = nand_to_mtd(chip); - const struct nand_data_interface *conf; int ret; if (!chip->setup_data_interface) @@ -1132,8 +1131,8 @@ static int nand_reset_data_interface(struct nand_chip *chip, int chipnr) * timings to timing mode 0. */ - conf = nand_get_default_data_interface(); - ret = chip->setup_data_interface(mtd, chipnr, conf); + onfi_fill_data_interface(chip, NAND_SDR_IFACE, 0); + ret = chip->setup_data_interface(mtd, chipnr, &chip->data_interface); if (ret) pr_err("Failed to configure data interface to SDR timing mode 0\n"); @@ -1158,7 +1157,7 @@ static int nand_setup_data_interface(struct nand_chip *chip, int chipnr) struct mtd_info *mtd = nand_to_mtd(chip); int ret; - if (!chip->setup_data_interface || !chip->data_interface) + if (!chip->setup_data_interface) return 0; /* @@ -1179,7 +1178,7 @@ static int nand_setup_data_interface(struct nand_chip *chip, int chipnr) goto err; } - ret = chip->setup_data_interface(mtd, chipnr, chip->data_interface); + ret = chip->setup_data_interface(mtd, chipnr, &chip->data_interface); err: return ret; } @@ -1219,21 +1218,16 @@ static int nand_init_data_interface(struct nand_chip *chip) modes = GENMASK(chip->onfi_timing_mode_default, 0); } - chip->data_interface = kzalloc(sizeof(*chip->data_interface), - GFP_KERNEL); - if (!chip->data_interface) - return -ENOMEM; for (mode = fls(modes) - 1; mode >= 0; mode--) { - ret = onfi_init_data_interface(chip, chip->data_interface, - NAND_SDR_IFACE, mode); + ret = onfi_fill_data_interface(chip, NAND_SDR_IFACE, mode); if (ret) continue; /* Pass -1 to only */ ret = chip->setup_data_interface(mtd, NAND_DATA_IFACE_CHECK_ONLY, - chip->data_interface); + &chip->data_interface); if (!ret) { chip->onfi_timing_mode_default = mode; break; @@ -1243,11 +1237,6 @@ static int nand_init_data_interface(struct nand_chip *chip) return 0; } -static void nand_release_data_interface(struct nand_chip *chip) -{ - kfree(chip->data_interface); -} - /** * nand_read_page_op - Do a READ PAGE operation * @chip: The NAND chip @@ -1763,11 +1752,16 @@ EXPORT_SYMBOL_GPL(nand_write_data_op); * @chip: The NAND chip * @chipnr: Internal die id * - * Returns 0 for success or negative error code otherwise + * Save the timings data structure, then apply SDR timings mode 0 (see + * nand_reset_data_interface for details), do the reset operation, and + * apply back the previous timings. + * + * Returns 0 on success, a negative error code otherwise. */ int nand_reset(struct nand_chip *chip, int chipnr) { struct mtd_info *mtd = nand_to_mtd(chip); + struct nand_data_interface saved_data_intf = chip->data_interface; int ret; ret = nand_reset_data_interface(chip, chipnr); @@ -1785,6 +1779,7 @@ int nand_reset(struct nand_chip *chip, int chipnr) return ret; chip->select_chip(mtd, chipnr); + chip->data_interface = saved_data_intf; ret = nand_setup_data_interface(chip, chipnr); chip->select_chip(mtd, -1); if (ret) @@ -4889,6 +4884,9 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips, struct nand_chip *chip = mtd_to_nand(mtd); int ret; + /* Enforce the right timings for reset/detection */ + onfi_fill_data_interface(chip, NAND_SDR_IFACE, 0); + ret = nand_dt_init(chip); if (ret) return ret; @@ -5629,7 +5627,7 @@ int nand_scan_tail(struct mtd_info *mtd) chip->select_chip(mtd, -1); if (ret) - goto err_nand_data_iface_cleanup; + goto err_nand_manuf_cleanup; } /* Check, if we should skip the bad block table scan */ @@ -5639,12 +5637,10 @@ int nand_scan_tail(struct mtd_info *mtd) /* Build bad block table */ ret = chip->scan_bbt(mtd); if (ret) - goto err_nand_data_iface_cleanup; + goto err_nand_manuf_cleanup; return 0; -err_nand_data_iface_cleanup: - nand_release_data_interface(chip); err_nand_manuf_cleanup: nand_manufacturer_cleanup(chip); @@ -5703,8 +5699,6 @@ void nand_cleanup(struct nand_chip *chip) chip->ecc.algo == NAND_ECC_BCH) nand_bch_free((struct nand_bch_control *)chip->ecc.priv); - nand_release_data_interface(chip); - /* Free bad block table memory */ kfree(chip->bbt); if (!(chip->options & NAND_OWN_BUFFERS) && chip->buffers) { diff --git a/drivers/mtd/nand/nand_timings.c b/drivers/mtd/nand/nand_timings.c index 5d1533bcc5bd..9400d039ddbd 100644 --- a/drivers/mtd/nand/nand_timings.c +++ b/drivers/mtd/nand/nand_timings.c @@ -283,16 +283,16 @@ const struct nand_sdr_timings *onfi_async_timing_mode_to_sdr_timings(int mode) EXPORT_SYMBOL(onfi_async_timing_mode_to_sdr_timings); /** - * onfi_init_data_interface - [NAND Interface] Initialize a data interface from + * onfi_fill_data_interface - [NAND Interface] Initialize a data interface from * given ONFI mode - * @iface: The data interface to be initialized * @mode: The ONFI timing mode */ -int onfi_init_data_interface(struct nand_chip *chip, - struct nand_data_interface *iface, +int onfi_fill_data_interface(struct nand_chip *chip, enum nand_data_interface_type type, int timing_mode) { + struct nand_data_interface *iface = &chip->data_interface; + if (type != NAND_SDR_IFACE) return -EINVAL; @@ -321,15 +321,4 @@ int onfi_init_data_interface(struct nand_chip *chip, return 0; } -EXPORT_SYMBOL(onfi_init_data_interface); - -/** - * nand_get_default_data_interface - [NAND Interface] Retrieve NAND - * data interface for mode 0. This is used as default timing after - * reset. - */ -const struct nand_data_interface *nand_get_default_data_interface(void) -{ - return &onfi_sdr_timings[0]; -} -EXPORT_SYMBOL(nand_get_default_data_interface); +EXPORT_SYMBOL(onfi_fill_data_interface); diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h index e6810f0b8f9e..2a72eab286ef 100644 --- a/include/linux/mtd/rawnand.h +++ b/include/linux/mtd/rawnand.h @@ -917,7 +917,7 @@ struct nand_chip { u16 max_bb_per_die; u32 blocks_per_die; - struct nand_data_interface *data_interface; + struct nand_data_interface data_interface; int read_retries; @@ -1214,8 +1214,7 @@ static inline int onfi_get_sync_timing_mode(struct nand_chip *chip) return le16_to_cpu(chip->onfi_params.src_sync_timing_mode); } -int onfi_init_data_interface(struct nand_chip *chip, - struct nand_data_interface *iface, +int onfi_fill_data_interface(struct nand_chip *chip, enum nand_data_interface_type type, int timing_mode); @@ -1258,8 +1257,6 @@ static inline int jedec_feature(struct nand_chip *chip) /* get timing characteristics from ONFI timing mode. */ const struct nand_sdr_timings *onfi_async_timing_mode_to_sdr_timings(int mode); -/* get data interface from ONFI timing mode 0, used after reset. */ -const struct nand_data_interface *nand_get_default_data_interface(void); int nand_check_erased_ecc_chunk(void *data, int datalen, void *ecc, int ecclen, -- cgit v1.2.3 From f880b07bf155226af8491d58558a41f2cf5245dc Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Tue, 5 Dec 2017 17:47:14 +0900 Subject: mtd: nand: cafe: remove use of NAND_OWN_BUFFERS This driver is the last/only user of NAND_OWN_BUFFERS. Boris suggested to remove this flag. Taking a closer look at this driver, it calls dma_alloc_coherent() for the concatenated area for the DMA bounce buffer + struct nand_buffers, but the latter does not need to be DMA-coherent; cafe_{write,read}_buf simply do memcpy() between buffers when usedma==1. Let's do dma_alloc_coherent() for the DMA bounce buffer in the front, and leave the nand_buffers allocation to nand_scan_tail(), then rip off NAND_OWN_BUFFERS. The magic number, 2112, is still mysterious (hard-coded writesize + oobsize ?), but this is not our main interest. I am keeping it. Suggested-by: Boris Brezillon Signed-off-by: Masahiro Yamada Signed-off-by: Boris Brezillon --- drivers/mtd/nand/cafe_nand.c | 24 ++++-------------------- 1 file changed, 4 insertions(+), 20 deletions(-) diff --git a/drivers/mtd/nand/cafe_nand.c b/drivers/mtd/nand/cafe_nand.c index de36762e3058..a438b7114053 100644 --- a/drivers/mtd/nand/cafe_nand.c +++ b/drivers/mtd/nand/cafe_nand.c @@ -605,7 +605,6 @@ static int cafe_nand_probe(struct pci_dev *pdev, uint32_t ctrl; int err = 0; int old_dma; - struct nand_buffers *nbuf; /* Very old versions shared the same PCI ident for all three functions on the chip. Verify the class too... */ @@ -653,7 +652,6 @@ static int cafe_nand_probe(struct pci_dev *pdev, /* Enable the following for a flash based bad block table */ cafe->nand.bbt_options = NAND_BBT_USE_FLASH; - cafe->nand.options = NAND_OWN_BUFFERS; if (skipbbt) { cafe->nand.options |= NAND_SKIP_BBTSCAN; @@ -723,15 +721,12 @@ static int cafe_nand_probe(struct pci_dev *pdev, if (err) goto out_irq; - cafe->dmabuf = dma_alloc_coherent(&cafe->pdev->dev, - 2112 + sizeof(struct nand_buffers) + - mtd->writesize + mtd->oobsize, - &cafe->dmaaddr, GFP_KERNEL); + cafe->dmabuf = dma_alloc_coherent(&cafe->pdev->dev, 2112, + &cafe->dmaaddr, GFP_KERNEL); if (!cafe->dmabuf) { err = -ENOMEM; goto out_irq; } - cafe->nand.buffers = nbuf = (void *)cafe->dmabuf + 2112; /* Set up DMA address */ cafe_writel(cafe, cafe->dmaaddr & 0xffffffff, NAND_DMA_ADDR0); @@ -744,11 +739,6 @@ static int cafe_nand_probe(struct pci_dev *pdev, cafe_dev_dbg(&cafe->pdev->dev, "Set DMA address to %x (virt %p)\n", cafe_readl(cafe, NAND_DMA_ADDR0), cafe->dmabuf); - /* this driver does not need the @ecccalc and @ecccode */ - nbuf->ecccalc = NULL; - nbuf->ecccode = NULL; - nbuf->databuf = (uint8_t *)(nbuf + 1); - /* Restore the DMA flag */ usedma = old_dma; @@ -793,10 +783,7 @@ static int cafe_nand_probe(struct pci_dev *pdev, goto out; out_free_dma: - dma_free_coherent(&cafe->pdev->dev, - 2112 + sizeof(struct nand_buffers) + - mtd->writesize + mtd->oobsize, - cafe->dmabuf, cafe->dmaaddr); + dma_free_coherent(&cafe->pdev->dev, 2112, cafe->dmabuf, cafe->dmaaddr); out_irq: /* Disable NAND IRQ in global IRQ mask register */ cafe_writel(cafe, ~1 & cafe_readl(cafe, GLOBAL_IRQ_MASK), GLOBAL_IRQ_MASK); @@ -821,10 +808,7 @@ static void cafe_nand_remove(struct pci_dev *pdev) nand_release(mtd); free_rs(cafe->rs); pci_iounmap(pdev, cafe->mmio); - dma_free_coherent(&cafe->pdev->dev, - 2112 + sizeof(struct nand_buffers) + - mtd->writesize + mtd->oobsize, - cafe->dmabuf, cafe->dmaaddr); + dma_free_coherent(&cafe->pdev->dev, 2112, cafe->dmabuf, cafe->dmaaddr); kfree(cafe); } -- cgit v1.2.3 From 8b311ead8bff9b56e512e3e544c488042ad0e7e7 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Tue, 5 Dec 2017 17:47:15 +0900 Subject: mtd: nand: remove unused NAND_OWN_BUFFERS flag The last/only user of NAND_OWN_BUFFERS (cafe_nand.c) has been reworked. This flag is no longer needed. Suggested-by: Boris Brezillon Signed-off-by: Masahiro Yamada Signed-off-by: Boris Brezillon --- drivers/mtd/nand/nand_base.c | 45 ++++++++++++++++++++------------------------ include/linux/mtd/rawnand.h | 5 ----- 2 files changed, 20 insertions(+), 30 deletions(-) diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 215c52a3b9ad..b63cc95e9179 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -5319,35 +5319,30 @@ int nand_scan_tail(struct mtd_info *mtd) return -EINVAL; } - if (!(chip->options & NAND_OWN_BUFFERS)) { - nbuf = kzalloc(sizeof(*nbuf), GFP_KERNEL); - if (!nbuf) - return -ENOMEM; - - nbuf->ecccalc = kmalloc(mtd->oobsize, GFP_KERNEL); - if (!nbuf->ecccalc) { - ret = -ENOMEM; - goto err_free_nbuf; - } + nbuf = kzalloc(sizeof(*nbuf), GFP_KERNEL); + if (!nbuf) + return -ENOMEM; - nbuf->ecccode = kmalloc(mtd->oobsize, GFP_KERNEL); - if (!nbuf->ecccode) { - ret = -ENOMEM; - goto err_free_nbuf; - } + nbuf->ecccalc = kmalloc(mtd->oobsize, GFP_KERNEL); + if (!nbuf->ecccalc) { + ret = -ENOMEM; + goto err_free_nbuf; + } - nbuf->databuf = kmalloc(mtd->writesize + mtd->oobsize, - GFP_KERNEL); - if (!nbuf->databuf) { - ret = -ENOMEM; - goto err_free_nbuf; - } + nbuf->ecccode = kmalloc(mtd->oobsize, GFP_KERNEL); + if (!nbuf->ecccode) { + ret = -ENOMEM; + goto err_free_nbuf; + } - chip->buffers = nbuf; - } else if (!chip->buffers) { - return -ENOMEM; + nbuf->databuf = kmalloc(mtd->writesize + mtd->oobsize, GFP_KERNEL); + if (!nbuf->databuf) { + ret = -ENOMEM; + goto err_free_nbuf; } + chip->buffers = nbuf; + /* * FIXME: some NAND manufacturer drivers expect the first die to be * selected when manufacturer->init() is called. They should be fixed @@ -5701,7 +5696,7 @@ void nand_cleanup(struct nand_chip *chip) /* Free bad block table memory */ kfree(chip->bbt); - if (!(chip->options & NAND_OWN_BUFFERS) && chip->buffers) { + if (chip->buffers) { kfree(chip->buffers->databuf); kfree(chip->buffers->ecccode); kfree(chip->buffers->ecccalc); diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h index 2a72eab286ef..fca802ef9af3 100644 --- a/include/linux/mtd/rawnand.h +++ b/include/linux/mtd/rawnand.h @@ -185,11 +185,6 @@ enum nand_ecc_algo { /* Non chip related options */ /* This option skips the bbt scan during initialization. */ #define NAND_SKIP_BBTSCAN 0x00010000 -/* - * This option is defined if the board driver allocates its own buffers - * (e.g. because it needs them DMA-coherent). - */ -#define NAND_OWN_BUFFERS 0x00020000 /* Chip may not exist, so silence any errors in scan */ #define NAND_SCAN_SILENT_NODEV 0x00040000 /* -- cgit v1.2.3 From c0313b966a0942fba934d34c7a76f444641d0b6e Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Tue, 5 Dec 2017 17:47:16 +0900 Subject: mtd: nand: squash struct nand_buffers into struct nand_chip struct nand_buffers is malloc'ed in nand_scan_tail() just for containing three pointers. Squash this struct into nand_chip. Move and rename as follows: chip->buffers->ecccalc -> chip->ecc.calc_buf chip->buffers->ecccode -> chip->ecc.code_buf chip->buffers->databuf -> chip->data_buf Signed-off-by: Masahiro Yamada Signed-off-by: Boris Brezillon --- drivers/mtd/nand/brcmnand/brcmnand.c | 2 +- drivers/mtd/nand/denali.c | 2 +- drivers/mtd/nand/fsmc_nand.c | 4 +- drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 4 +- drivers/mtd/nand/nand_base.c | 91 ++++++++++++++-------------------- drivers/mtd/nand/nand_bbt.c | 2 +- drivers/mtd/nand/omap2.c | 10 ++-- drivers/mtd/nand/sunxi_nand.c | 6 +-- include/linux/mtd/rawnand.h | 23 +++------ 9 files changed, 59 insertions(+), 85 deletions(-) diff --git a/drivers/mtd/nand/brcmnand/brcmnand.c b/drivers/mtd/nand/brcmnand/brcmnand.c index e6879d4d53ca..54842512edb1 100644 --- a/drivers/mtd/nand/brcmnand/brcmnand.c +++ b/drivers/mtd/nand/brcmnand/brcmnand.c @@ -1681,7 +1681,7 @@ static int brcmstb_nand_verify_erased_page(struct mtd_info *mtd, int ret; if (!buf) { - buf = chip->buffers->databuf; + buf = chip->data_buf; /* Invalidate page cache */ chip->pagebuf = -1; } diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c index 47a253737bb2..00698b33cb22 100644 --- a/drivers/mtd/nand/denali.c +++ b/drivers/mtd/nand/denali.c @@ -330,7 +330,7 @@ static int denali_check_erased_page(struct mtd_info *mtd, unsigned long uncor_ecc_flags, unsigned int max_bitflips) { - uint8_t *ecc_code = chip->buffers->ecccode; + uint8_t *ecc_code = chip->ecc.code_buf; int ecc_steps = chip->ecc.steps; int ecc_size = chip->ecc.size; int ecc_bytes = chip->ecc.bytes; diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c index b44e5c6545e0..f49ed46fa770 100644 --- a/drivers/mtd/nand/fsmc_nand.c +++ b/drivers/mtd/nand/fsmc_nand.c @@ -684,8 +684,8 @@ static int fsmc_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, int eccbytes = chip->ecc.bytes; int eccsteps = chip->ecc.steps; uint8_t *p = buf; - uint8_t *ecc_calc = chip->buffers->ecccalc; - uint8_t *ecc_code = chip->buffers->ecccode; + uint8_t *ecc_calc = chip->ecc.calc_buf; + uint8_t *ecc_code = chip->ecc.code_buf; int off, len, group = 0; /* * ecc_oob is intentionally taken as uint16_t. In 16bit devices, we diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c index 3c3f3f58fdcb..b51db8c85405 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c @@ -1696,7 +1696,7 @@ static int mx23_check_transcription_stamp(struct gpmi_nand_data *this) unsigned int search_area_size_in_strides; unsigned int stride; unsigned int page; - uint8_t *buffer = chip->buffers->databuf; + uint8_t *buffer = chip->data_buf; int saved_chip_number; int found_an_ncb_fingerprint = false; @@ -1755,7 +1755,7 @@ static int mx23_write_transcription_stamp(struct gpmi_nand_data *this) unsigned int block; unsigned int stride; unsigned int page; - uint8_t *buffer = chip->buffers->databuf; + uint8_t *buffer = chip->data_buf; int saved_chip_number; int status; diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index b63cc95e9179..32c0239b380a 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -2030,8 +2030,8 @@ static int nand_read_page_swecc(struct mtd_info *mtd, struct nand_chip *chip, int eccbytes = chip->ecc.bytes; int eccsteps = chip->ecc.steps; uint8_t *p = buf; - uint8_t *ecc_calc = chip->buffers->ecccalc; - uint8_t *ecc_code = chip->buffers->ecccode; + uint8_t *ecc_calc = chip->ecc.calc_buf; + uint8_t *ecc_code = chip->ecc.code_buf; unsigned int max_bitflips = 0; chip->ecc.read_page_raw(mtd, chip, buf, 1, page); @@ -2102,7 +2102,7 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, /* Calculate ECC */ for (i = 0; i < eccfrag_len ; i += chip->ecc.bytes, p += chip->ecc.size) - chip->ecc.calculate(mtd, p, &chip->buffers->ecccalc[i]); + chip->ecc.calculate(mtd, p, &chip->ecc.calc_buf[i]); /* * The performance is faster if we position offsets according to @@ -2142,7 +2142,7 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, return ret; } - ret = mtd_ooblayout_get_eccbytes(mtd, chip->buffers->ecccode, + ret = mtd_ooblayout_get_eccbytes(mtd, chip->ecc.code_buf, chip->oob_poi, index, eccfrag_len); if (ret) return ret; @@ -2151,13 +2151,13 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, for (i = 0; i < eccfrag_len ; i += chip->ecc.bytes, p += chip->ecc.size) { int stat; - stat = chip->ecc.correct(mtd, p, - &chip->buffers->ecccode[i], &chip->buffers->ecccalc[i]); + stat = chip->ecc.correct(mtd, p, &chip->ecc.code_buf[i], + &chip->ecc.calc_buf[i]); if (stat == -EBADMSG && (chip->ecc.options & NAND_ECC_GENERIC_ERASED_CHECK)) { /* check for empty pages with bitflips */ stat = nand_check_erased_ecc_chunk(p, chip->ecc.size, - &chip->buffers->ecccode[i], + &chip->ecc.code_buf[i], chip->ecc.bytes, NULL, 0, chip->ecc.strength); @@ -2190,8 +2190,8 @@ static int nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, int eccbytes = chip->ecc.bytes; int eccsteps = chip->ecc.steps; uint8_t *p = buf; - uint8_t *ecc_calc = chip->buffers->ecccalc; - uint8_t *ecc_code = chip->buffers->ecccode; + uint8_t *ecc_calc = chip->ecc.calc_buf; + uint8_t *ecc_code = chip->ecc.code_buf; unsigned int max_bitflips = 0; ret = nand_read_page_op(chip, page, 0, NULL, 0); @@ -2264,8 +2264,8 @@ static int nand_read_page_hwecc_oob_first(struct mtd_info *mtd, int eccbytes = chip->ecc.bytes; int eccsteps = chip->ecc.steps; uint8_t *p = buf; - uint8_t *ecc_code = chip->buffers->ecccode; - uint8_t *ecc_calc = chip->buffers->ecccalc; + uint8_t *ecc_code = chip->ecc.code_buf; + uint8_t *ecc_calc = chip->ecc.calc_buf; unsigned int max_bitflips = 0; /* Read the OOB area first */ @@ -2514,7 +2514,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, /* Is the current page in the buffer? */ if (realpage != chip->pagebuf || oob) { - bufpoi = use_bufpoi ? chip->buffers->databuf : buf; + bufpoi = use_bufpoi ? chip->data_buf : buf; if (use_bufpoi && aligned) pr_debug("%s: using read bounce buffer for buf@%p\n", @@ -2555,7 +2555,7 @@ read_retry: /* Invalidate page cache */ chip->pagebuf = -1; } - memcpy(buf, chip->buffers->databuf + col, bytes); + memcpy(buf, chip->data_buf + col, bytes); } if (unlikely(oob)) { @@ -2596,7 +2596,7 @@ read_retry: buf += bytes; max_bitflips = max_t(unsigned int, max_bitflips, ret); } else { - memcpy(buf, chip->buffers->databuf + col, bytes); + memcpy(buf, chip->data_buf + col, bytes); buf += bytes; max_bitflips = max_t(unsigned int, max_bitflips, chip->pagebuf_bitflips); @@ -3071,7 +3071,7 @@ static int nand_write_page_swecc(struct mtd_info *mtd, struct nand_chip *chip, int i, eccsize = chip->ecc.size, ret; int eccbytes = chip->ecc.bytes; int eccsteps = chip->ecc.steps; - uint8_t *ecc_calc = chip->buffers->ecccalc; + uint8_t *ecc_calc = chip->ecc.calc_buf; const uint8_t *p = buf; /* Software ECC calculation */ @@ -3101,7 +3101,7 @@ static int nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, int i, eccsize = chip->ecc.size, ret; int eccbytes = chip->ecc.bytes; int eccsteps = chip->ecc.steps; - uint8_t *ecc_calc = chip->buffers->ecccalc; + uint8_t *ecc_calc = chip->ecc.calc_buf; const uint8_t *p = buf; ret = nand_prog_page_begin_op(chip, page, 0, NULL, 0); @@ -3147,7 +3147,7 @@ static int nand_write_subpage_hwecc(struct mtd_info *mtd, int oob_required, int page) { uint8_t *oob_buf = chip->oob_poi; - uint8_t *ecc_calc = chip->buffers->ecccalc; + uint8_t *ecc_calc = chip->ecc.calc_buf; int ecc_size = chip->ecc.size; int ecc_bytes = chip->ecc.bytes; int ecc_steps = chip->ecc.steps; @@ -3187,7 +3187,7 @@ static int nand_write_subpage_hwecc(struct mtd_info *mtd, /* copy calculated ECC for whole page to chip->buffer->oob */ /* this include masked-value(0xFF) for unwritten subpages */ - ecc_calc = chip->buffers->ecccalc; + ecc_calc = chip->ecc.calc_buf; ret = mtd_ooblayout_set_eccbytes(mtd, ecc_calc, chip->oob_poi, 0, chip->ecc.total); if (ret) @@ -3434,9 +3434,9 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to, if (part_pagewr) bytes = min_t(int, bytes - column, writelen); chip->pagebuf = -1; - memset(chip->buffers->databuf, 0xff, mtd->writesize); - memcpy(&chip->buffers->databuf[column], buf, bytes); - wbuf = chip->buffers->databuf; + memset(chip->data_buf, 0xff, mtd->writesize); + memcpy(&chip->data_buf[column], buf, bytes); + wbuf = chip->data_buf; } if (unlikely(oob)) { @@ -5310,7 +5310,6 @@ int nand_scan_tail(struct mtd_info *mtd) { struct nand_chip *chip = mtd_to_nand(mtd); struct nand_ecc_ctrl *ecc = &chip->ecc; - struct nand_buffers *nbuf = NULL; int ret, i; /* New bad blocks should be marked in OOB, flash-based BBT, or both */ @@ -5319,30 +5318,22 @@ int nand_scan_tail(struct mtd_info *mtd) return -EINVAL; } - nbuf = kzalloc(sizeof(*nbuf), GFP_KERNEL); - if (!nbuf) + ecc->calc_buf = kmalloc(mtd->oobsize, GFP_KERNEL); + if (!ecc->calc_buf) return -ENOMEM; - nbuf->ecccalc = kmalloc(mtd->oobsize, GFP_KERNEL); - if (!nbuf->ecccalc) { + ecc->code_buf = kmalloc(mtd->oobsize, GFP_KERNEL); + if (!ecc->code_buf) { ret = -ENOMEM; - goto err_free_nbuf; + goto err_free_buf; } - nbuf->ecccode = kmalloc(mtd->oobsize, GFP_KERNEL); - if (!nbuf->ecccode) { + chip->data_buf = kmalloc(mtd->writesize + mtd->oobsize, GFP_KERNEL); + if (!chip->data_buf) { ret = -ENOMEM; - goto err_free_nbuf; + goto err_free_buf; } - nbuf->databuf = kmalloc(mtd->writesize + mtd->oobsize, GFP_KERNEL); - if (!nbuf->databuf) { - ret = -ENOMEM; - goto err_free_nbuf; - } - - chip->buffers = nbuf; - /* * FIXME: some NAND manufacturer drivers expect the first die to be * selected when manufacturer->init() is called. They should be fixed @@ -5353,10 +5344,10 @@ int nand_scan_tail(struct mtd_info *mtd) ret = nand_manufacturer_init(chip); chip->select_chip(mtd, -1); if (ret) - goto err_free_nbuf; + goto err_free_buf; /* Set the internal oob buffer location, just after the page data */ - chip->oob_poi = chip->buffers->databuf + mtd->writesize; + chip->oob_poi = chip->data_buf + mtd->writesize; /* * If no default placement scheme is given, select an appropriate one. @@ -5640,13 +5631,10 @@ int nand_scan_tail(struct mtd_info *mtd) err_nand_manuf_cleanup: nand_manufacturer_cleanup(chip); -err_free_nbuf: - if (nbuf) { - kfree(nbuf->databuf); - kfree(nbuf->ecccode); - kfree(nbuf->ecccalc); - kfree(nbuf); - } +err_free_buf: + kfree(chip->data_buf); + kfree(ecc->code_buf); + kfree(ecc->calc_buf); return ret; } @@ -5696,12 +5684,9 @@ void nand_cleanup(struct nand_chip *chip) /* Free bad block table memory */ kfree(chip->bbt); - if (chip->buffers) { - kfree(chip->buffers->databuf); - kfree(chip->buffers->ecccode); - kfree(chip->buffers->ecccalc); - kfree(chip->buffers); - } + kfree(chip->data_buf); + kfree(chip->ecc.code_buf); + kfree(chip->ecc.calc_buf); /* Free bad block descriptor memory */ if (chip->badblock_pattern && chip->badblock_pattern->options diff --git a/drivers/mtd/nand/nand_bbt.c b/drivers/mtd/nand/nand_bbt.c index 2915b6739bf8..36092850be2c 100644 --- a/drivers/mtd/nand/nand_bbt.c +++ b/drivers/mtd/nand/nand_bbt.c @@ -898,7 +898,7 @@ static inline int nand_memory_bbt(struct mtd_info *mtd, struct nand_bbt_descr *b { struct nand_chip *this = mtd_to_nand(mtd); - return create_bbt(mtd, this->buffers->databuf, bd, -1); + return create_bbt(mtd, this->data_buf, bd, -1); } /** diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index 5cb4db6f88e3..8cdf7d3d8fa7 100644 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -1530,7 +1530,7 @@ static int omap_write_page_bch(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required, int page) { int ret; - uint8_t *ecc_calc = chip->buffers->ecccalc; + uint8_t *ecc_calc = chip->ecc.calc_buf; nand_prog_page_begin_op(chip, page, 0, NULL, 0); @@ -1571,7 +1571,7 @@ static int omap_write_subpage_bch(struct mtd_info *mtd, u32 data_len, const u8 *buf, int oob_required, int page) { - u8 *ecc_calc = chip->buffers->ecccalc; + u8 *ecc_calc = chip->ecc.calc_buf; int ecc_size = chip->ecc.size; int ecc_bytes = chip->ecc.bytes; int ecc_steps = chip->ecc.steps; @@ -1609,7 +1609,7 @@ static int omap_write_subpage_bch(struct mtd_info *mtd, /* copy calculated ECC for whole page to chip->buffer->oob */ /* this include masked-value(0xFF) for unwritten subpages */ - ecc_calc = chip->buffers->ecccalc; + ecc_calc = chip->ecc.calc_buf; ret = mtd_ooblayout_set_eccbytes(mtd, ecc_calc, chip->oob_poi, 0, chip->ecc.total); if (ret) @@ -1639,8 +1639,8 @@ static int omap_write_subpage_bch(struct mtd_info *mtd, static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf, int oob_required, int page) { - uint8_t *ecc_calc = chip->buffers->ecccalc; - uint8_t *ecc_code = chip->buffers->ecccode; + uint8_t *ecc_calc = chip->ecc.calc_buf; + uint8_t *ecc_code = chip->ecc.code_buf; int stat, ret; unsigned int max_bitflips = 0; diff --git a/drivers/mtd/nand/sunxi_nand.c b/drivers/mtd/nand/sunxi_nand.c index 5c176dee821e..2275fbedfb2a 100644 --- a/drivers/mtd/nand/sunxi_nand.c +++ b/drivers/mtd/nand/sunxi_nand.c @@ -1555,7 +1555,7 @@ static int sunxi_nfc_hw_common_ecc_read_oob(struct mtd_info *mtd, { chip->pagebuf = -1; - return chip->ecc.read_page(mtd, chip, chip->buffers->databuf, 1, page); + return chip->ecc.read_page(mtd, chip, chip->data_buf, 1, page); } static int sunxi_nfc_hw_common_ecc_write_oob(struct mtd_info *mtd, @@ -1566,8 +1566,8 @@ static int sunxi_nfc_hw_common_ecc_write_oob(struct mtd_info *mtd, chip->pagebuf = -1; - memset(chip->buffers->databuf, 0xff, mtd->writesize); - ret = chip->ecc.write_page(mtd, chip, chip->buffers->databuf, 1, page); + memset(chip->data_buf, 0xff, mtd->writesize); + ret = chip->ecc.write_page(mtd, chip, chip->data_buf, 1, page); if (ret) return ret; diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h index fca802ef9af3..f8f27c6801a6 100644 --- a/include/linux/mtd/rawnand.h +++ b/include/linux/mtd/rawnand.h @@ -514,6 +514,8 @@ static const struct nand_ecc_caps __name = { \ * @postpad: padding information for syndrome based ECC generators * @options: ECC specific options (see NAND_ECC_XXX flags defined above) * @priv: pointer to private ECC control data + * @calc_buf: buffer for calculated ECC, size is oobsize. + * @code_buf: buffer for ECC read from flash, size is oobsize. * @hwctl: function to control hardware ECC generator. Must only * be provided if an hardware ECC is available * @calculate: function for ECC calculation or readback from ECC hardware @@ -564,6 +566,8 @@ struct nand_ecc_ctrl { int postpad; unsigned int options; void *priv; + u8 *calc_buf; + u8 *code_buf; void (*hwctl)(struct mtd_info *mtd, int mode); int (*calculate)(struct mtd_info *mtd, const uint8_t *dat, uint8_t *ecc_code); @@ -591,21 +595,6 @@ struct nand_ecc_ctrl { int page); }; -/** - * struct nand_buffers - buffer structure for read/write - * @ecccalc: buffer pointer for calculated ECC, size is oobsize. - * @ecccode: buffer pointer for ECC read from flash, size is oobsize. - * @databuf: buffer pointer for data, size is (page size + oobsize). - * - * Do not change the order of buffers. databuf and oobrbuf must be in - * consecutive order. - */ -struct nand_buffers { - uint8_t *ecccalc; - uint8_t *ecccode; - uint8_t *databuf; -}; - /** * struct nand_sdr_timings - SDR NAND chip timings * @@ -774,7 +763,6 @@ struct nand_manufacturer_ops { * @setup_read_retry: [FLASHSPECIFIC] flash (vendor) specific function for * setting the read-retry mode. Mostly needed for MLC NAND. * @ecc: [BOARDSPECIFIC] ECC control structure - * @buffers: buffer structure for read/write * @buf_align: minimum buffer alignment required by a platform * @hwcontrol: platform-specific hardware control structure * @erase: [REPLACEABLE] erase function @@ -814,6 +802,7 @@ struct nand_manufacturer_ops { * @numchips: [INTERN] number of physical chips * @chipsize: [INTERN] the size of one chip for multichip arrays * @pagemask: [INTERN] page number mask = number of (pages / chip) - 1 + * @data_buf: [INTERN] buffer for data, size is (page size + oobsize). * @pagebuf: [INTERN] holds the pagenumber which is currently in * data_buf. * @pagebuf_bitflips: [INTERN] holds the bitflip count for the page which is @@ -892,6 +881,7 @@ struct nand_chip { int numchips; uint64_t chipsize; int pagemask; + u8 *data_buf; int pagebuf; unsigned int pagebuf_bitflips; int subpagesize; @@ -922,7 +912,6 @@ struct nand_chip { struct nand_hw_control *controller; struct nand_ecc_ctrl ecc; - struct nand_buffers *buffers; unsigned long buf_align; struct nand_hw_control hwcontrol; -- cgit v1.2.3 From 958ef111cca5e70994b806127ff15258d446ed25 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Tue, 5 Dec 2017 17:49:56 +0900 Subject: mtd: nand: cafe: clean up DMA address setup Use macros from to make the code readable. The compiler warning will be kept suppressed. Signed-off-by: Masahiro Yamada Signed-off-by: Boris Brezillon --- drivers/mtd/nand/cafe_nand.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-) diff --git a/drivers/mtd/nand/cafe_nand.c b/drivers/mtd/nand/cafe_nand.c index a438b7114053..567ff972d5fc 100644 --- a/drivers/mtd/nand/cafe_nand.c +++ b/drivers/mtd/nand/cafe_nand.c @@ -729,12 +729,8 @@ static int cafe_nand_probe(struct pci_dev *pdev, } /* Set up DMA address */ - cafe_writel(cafe, cafe->dmaaddr & 0xffffffff, NAND_DMA_ADDR0); - if (sizeof(cafe->dmaaddr) > 4) - /* Shift in two parts to shut the compiler up */ - cafe_writel(cafe, (cafe->dmaaddr >> 16) >> 16, NAND_DMA_ADDR1); - else - cafe_writel(cafe, 0, NAND_DMA_ADDR1); + cafe_writel(cafe, lower_32_bits(cafe->dmaaddr), NAND_DMA_ADDR0); + cafe_writel(cafe, upper_32_bits(cafe->dmaaddr), NAND_DMA_ADDR1); cafe_dev_dbg(&cafe->pdev->dev, "Set DMA address to %x (virt %p)\n", cafe_readl(cafe, NAND_DMA_ADDR0), cafe->dmabuf); -- cgit v1.2.3 From f170c6fb7036dca779bbcb2e0fea4b4eed3201b1 Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Mon, 27 Nov 2017 23:52:56 +0100 Subject: mtd: onenand: Remove obsolete url from Kconfig help Samsung website no longer host information about OneNAND, delete it. Signed-off-by: Ladislav Michl Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/Kconfig | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/mtd/onenand/Kconfig b/drivers/mtd/onenand/Kconfig index dcae2f6a2b11..aaeb30458139 100644 --- a/drivers/mtd/onenand/Kconfig +++ b/drivers/mtd/onenand/Kconfig @@ -4,8 +4,7 @@ menuconfig MTD_ONENAND depends on HAS_IOMEM help This enables support for accessing all type of OneNAND flash - devices. For further information see - + devices. if MTD_ONENAND -- cgit v1.2.3 From 624d5abf6c008ba00b2b868990708d5f2a5e2d08 Mon Sep 17 00:00:00 2001 From: RogerCC Lin Date: Thu, 30 Nov 2017 22:10:43 +0800 Subject: mtd: nand: mtk: update DT bindings Add MT7622 NAND Flash Controller dt bindings documentation. Signed-off-by: RogerCC Lin Reviewed-by: Matthias Brugger Signed-off-by: Boris Brezillon --- Documentation/devicetree/bindings/mtd/mtk-nand.txt | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt index dbf9e054c11c..0025bc4c94a0 100644 --- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt +++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt @@ -12,8 +12,10 @@ tree nodes. The first part of NFC is NAND Controller Interface (NFI) HW. Required NFI properties: -- compatible: Should be one of "mediatek,mt2701-nfc", - "mediatek,mt2712-nfc". +- compatible: Should be one of + "mediatek,mt2701-nfc", + "mediatek,mt2712-nfc", + "mediatek,mt7622-nfc". - reg: Base physical address and size of NFI. - interrupts: Interrupts of NFI. - clocks: NFI required clocks. @@ -142,7 +144,10 @@ Example: ============== Required BCH properties: -- compatible: Should be one of "mediatek,mt2701-ecc", "mediatek,mt2712-ecc". +- compatible: Should be one of + "mediatek,mt2701-ecc", + "mediatek,mt2712-ecc", + "mediatek,mt7622-ecc". - reg: Base physical address and size of ECC. - interrupts: Interrupts of ECC. - clocks: ECC required clocks. -- cgit v1.2.3 From b45ee5501ede9a369e9bc20edca508193b848d25 Mon Sep 17 00:00:00 2001 From: RogerCC Lin Date: Thu, 30 Nov 2017 22:10:44 +0800 Subject: mtd: nand: mtk: Support different MTK NAND flash controller IP MT7622 uses an MTK's earlier NAND flash controller IP which support different sector size, max spare size per sector and paraity bits..., some register's offset and definition also been changed in the NAND flash controller, this patch is the preparation to support MT7622 NAND flash controller. MT7622 NFC and ECC engine are similar to MT2701's, except below differences: (1)MT7622 NFC's max sector size(ECC data size) is 512 bytes, and MT2701's is 1024, and MT7622's max sector number is 8. (2)The parity bit of MT7622 is 13, MT2701 is 14. (3)MT7622 ECC supports less ECC strength, max to 16 bit ecc strength. (4)MT7622 supports less spare size per sector, max spare size per sector is 28 bytes. (5)Some register's offset are different, include ECC_ENCIRQ_EN, ECC_ENCIRQ_STA, ECC_DECDONE, ECC_DECIRQ_EN and ECC_DECIRQ_STA. (6)ENC_MODE of ECC_ENCCNFG register is moved from bit 5-6 to bit 4-5. Signed-off-by: RogerCC Lin Signed-off-by: Boris Brezillon --- drivers/mtd/nand/mtk_ecc.c | 100 ++++++++++++++++++++++++++++++-------------- drivers/mtd/nand/mtk_ecc.h | 3 +- drivers/mtd/nand/mtk_nand.c | 27 ++++++++---- 3 files changed, 89 insertions(+), 41 deletions(-) diff --git a/drivers/mtd/nand/mtk_ecc.c b/drivers/mtd/nand/mtk_ecc.c index c51d214d169e..6610eefaa92b 100644 --- a/drivers/mtd/nand/mtk_ecc.c +++ b/drivers/mtd/nand/mtk_ecc.c @@ -34,34 +34,28 @@ #define ECC_ENCCON (0x00) #define ECC_ENCCNFG (0x04) -#define ECC_MODE_SHIFT (5) #define ECC_MS_SHIFT (16) #define ECC_ENCDIADDR (0x08) #define ECC_ENCIDLE (0x0C) -#define ECC_ENCIRQ_EN (0x80) -#define ECC_ENCIRQ_STA (0x84) #define ECC_DECCON (0x100) #define ECC_DECCNFG (0x104) #define DEC_EMPTY_EN BIT(31) #define DEC_CNFG_CORRECT (0x3 << 12) #define ECC_DECIDLE (0x10C) #define ECC_DECENUM0 (0x114) -#define ECC_DECDONE (0x124) -#define ECC_DECIRQ_EN (0x200) -#define ECC_DECIRQ_STA (0x204) #define ECC_TIMEOUT (500000) #define ECC_IDLE_REG(op) ((op) == ECC_ENCODE ? ECC_ENCIDLE : ECC_DECIDLE) #define ECC_CTL_REG(op) ((op) == ECC_ENCODE ? ECC_ENCCON : ECC_DECCON) -#define ECC_IRQ_REG(op) ((op) == ECC_ENCODE ? \ - ECC_ENCIRQ_EN : ECC_DECIRQ_EN) struct mtk_ecc_caps { u32 err_mask; const u8 *ecc_strength; + const u32 *ecc_regs; u8 num_ecc_strength; - u32 encode_parity_reg0; + u8 ecc_mode_shift; + u32 parity_bits; int pg_irq_sel; }; @@ -89,6 +83,33 @@ static const u8 ecc_strength_mt2712[] = { 40, 44, 48, 52, 56, 60, 68, 72, 80 }; +enum mtk_ecc_regs { + ECC_ENCPAR00, + ECC_ENCIRQ_EN, + ECC_ENCIRQ_STA, + ECC_DECDONE, + ECC_DECIRQ_EN, + ECC_DECIRQ_STA, +}; + +static int mt2701_ecc_regs[] = { + [ECC_ENCPAR00] = 0x10, + [ECC_ENCIRQ_EN] = 0x80, + [ECC_ENCIRQ_STA] = 0x84, + [ECC_DECDONE] = 0x124, + [ECC_DECIRQ_EN] = 0x200, + [ECC_DECIRQ_STA] = 0x204, +}; + +static int mt2712_ecc_regs[] = { + [ECC_ENCPAR00] = 0x300, + [ECC_ENCIRQ_EN] = 0x80, + [ECC_ENCIRQ_STA] = 0x84, + [ECC_DECDONE] = 0x124, + [ECC_DECIRQ_EN] = 0x200, + [ECC_DECIRQ_STA] = 0x204, +}; + static inline void mtk_ecc_wait_idle(struct mtk_ecc *ecc, enum mtk_ecc_operation op) { @@ -107,32 +128,30 @@ static inline void mtk_ecc_wait_idle(struct mtk_ecc *ecc, static irqreturn_t mtk_ecc_irq(int irq, void *id) { struct mtk_ecc *ecc = id; - enum mtk_ecc_operation op; u32 dec, enc; - dec = readw(ecc->regs + ECC_DECIRQ_STA) & ECC_IRQ_EN; + dec = readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECIRQ_STA]) + & ECC_IRQ_EN; if (dec) { - op = ECC_DECODE; - dec = readw(ecc->regs + ECC_DECDONE); + dec = readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECDONE]); if (dec & ecc->sectors) { /* * Clear decode IRQ status once again to ensure that * there will be no extra IRQ. */ - readw(ecc->regs + ECC_DECIRQ_STA); + readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECIRQ_STA]); ecc->sectors = 0; complete(&ecc->done); } else { return IRQ_HANDLED; } } else { - enc = readl(ecc->regs + ECC_ENCIRQ_STA) & ECC_IRQ_EN; - if (enc) { - op = ECC_ENCODE; + enc = readl(ecc->regs + ecc->caps->ecc_regs[ECC_ENCIRQ_STA]) + & ECC_IRQ_EN; + if (enc) complete(&ecc->done); - } else { + else return IRQ_NONE; - } } return IRQ_HANDLED; @@ -160,7 +179,7 @@ static int mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config) /* configure ECC encoder (in bits) */ enc_sz = config->len << 3; - reg = ecc_bit | (config->mode << ECC_MODE_SHIFT); + reg = ecc_bit | (config->mode << ecc->caps->ecc_mode_shift); reg |= (enc_sz << ECC_MS_SHIFT); writel(reg, ecc->regs + ECC_ENCCNFG); @@ -171,9 +190,9 @@ static int mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config) } else { /* configure ECC decoder (in bits) */ dec_sz = (config->len << 3) + - config->strength * ECC_PARITY_BITS; + config->strength * ecc->caps->parity_bits; - reg = ecc_bit | (config->mode << ECC_MODE_SHIFT); + reg = ecc_bit | (config->mode << ecc->caps->ecc_mode_shift); reg |= (dec_sz << ECC_MS_SHIFT) | DEC_CNFG_CORRECT; reg |= DEC_EMPTY_EN; writel(reg, ecc->regs + ECC_DECCNFG); @@ -291,7 +310,12 @@ int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config) */ if (ecc->caps->pg_irq_sel && config->mode == ECC_NFI_MODE) reg_val |= ECC_PG_IRQ_SEL; - writew(reg_val, ecc->regs + ECC_IRQ_REG(op)); + if (op == ECC_ENCODE) + writew(reg_val, ecc->regs + + ecc->caps->ecc_regs[ECC_ENCIRQ_EN]); + else + writew(reg_val, ecc->regs + + ecc->caps->ecc_regs[ECC_DECIRQ_EN]); } writew(ECC_OP_ENABLE, ecc->regs + ECC_CTL_REG(op)); @@ -310,13 +334,17 @@ void mtk_ecc_disable(struct mtk_ecc *ecc) /* disable it */ mtk_ecc_wait_idle(ecc, op); - if (op == ECC_DECODE) + if (op == ECC_DECODE) { /* * Clear decode IRQ status in case there is a timeout to wait * decode IRQ. */ - readw(ecc->regs + ECC_DECIRQ_STA); - writew(0, ecc->regs + ECC_IRQ_REG(op)); + readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECDONE]); + writew(0, ecc->regs + ecc->caps->ecc_regs[ECC_DECIRQ_EN]); + } else { + writew(0, ecc->regs + ecc->caps->ecc_regs[ECC_ENCIRQ_EN]); + } + writew(ECC_OP_DISABLE, ecc->regs + ECC_CTL_REG(op)); mutex_unlock(&ecc->lock); @@ -367,11 +395,11 @@ int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config, mtk_ecc_wait_idle(ecc, ECC_ENCODE); /* Program ECC bytes to OOB: per sector oob = FDM + ECC + SPARE */ - len = (config->strength * ECC_PARITY_BITS + 7) >> 3; + len = (config->strength * ecc->caps->parity_bits + 7) >> 3; /* write the parity bytes generated by the ECC back to temp buffer */ __ioread32_copy(ecc->eccdata, - ecc->regs + ecc->caps->encode_parity_reg0, + ecc->regs + ecc->caps->ecc_regs[ECC_ENCPAR00], round_up(len, 4)); /* copy into possibly unaligned OOB region with actual length */ @@ -404,19 +432,29 @@ void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p) } EXPORT_SYMBOL(mtk_ecc_adjust_strength); +unsigned int mtk_ecc_get_parity_bits(struct mtk_ecc *ecc) +{ + return ecc->caps->parity_bits; +} +EXPORT_SYMBOL(mtk_ecc_get_parity_bits); + static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = { .err_mask = 0x3f, .ecc_strength = ecc_strength_mt2701, + .ecc_regs = mt2701_ecc_regs, .num_ecc_strength = 20, - .encode_parity_reg0 = 0x10, + .ecc_mode_shift = 5, + .parity_bits = 14, .pg_irq_sel = 0, }; static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = { .err_mask = 0x7f, .ecc_strength = ecc_strength_mt2712, + .ecc_regs = mt2712_ecc_regs, .num_ecc_strength = 23, - .encode_parity_reg0 = 0x300, + .ecc_mode_shift = 5, + .parity_bits = 14, .pg_irq_sel = 1, }; @@ -452,7 +490,7 @@ static int mtk_ecc_probe(struct platform_device *pdev) max_eccdata_size = ecc->caps->num_ecc_strength - 1; max_eccdata_size = ecc->caps->ecc_strength[max_eccdata_size]; - max_eccdata_size = (max_eccdata_size * ECC_PARITY_BITS + 7) >> 3; + max_eccdata_size = (max_eccdata_size * ecc->caps->parity_bits + 7) >> 3; max_eccdata_size = round_up(max_eccdata_size, 4); ecc->eccdata = devm_kzalloc(dev, max_eccdata_size, GFP_KERNEL); if (!ecc->eccdata) diff --git a/drivers/mtd/nand/mtk_ecc.h b/drivers/mtd/nand/mtk_ecc.h index d245c14f1b80..a455df080952 100644 --- a/drivers/mtd/nand/mtk_ecc.h +++ b/drivers/mtd/nand/mtk_ecc.h @@ -14,8 +14,6 @@ #include -#define ECC_PARITY_BITS (14) - enum mtk_ecc_mode {ECC_DMA_MODE = 0, ECC_NFI_MODE = 1}; enum mtk_ecc_operation {ECC_ENCODE, ECC_DECODE}; @@ -43,6 +41,7 @@ int mtk_ecc_wait_done(struct mtk_ecc *, enum mtk_ecc_operation); int mtk_ecc_enable(struct mtk_ecc *, struct mtk_ecc_config *); void mtk_ecc_disable(struct mtk_ecc *); void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p); +unsigned int mtk_ecc_get_parity_bits(struct mtk_ecc *ecc); struct mtk_ecc *of_mtk_ecc_get(struct device_node *); void mtk_ecc_release(struct mtk_ecc *); diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/mtk_nand.c index 5d76be451596..b9946ae58616 100644 --- a/drivers/mtd/nand/mtk_nand.c +++ b/drivers/mtd/nand/mtk_nand.c @@ -97,7 +97,6 @@ #define MTK_TIMEOUT (500000) #define MTK_RESET_TIMEOUT (1000000) -#define MTK_MAX_SECTOR (16) #define MTK_NAND_MAX_NSELS (2) #define MTK_NFC_MIN_SPARE (16) #define ACCTIMING(tpoecs, tprecs, tc2r, tw2r, twh, twst, trlt) \ @@ -109,6 +108,8 @@ struct mtk_nfc_caps { u8 num_spare_size; u8 pageformat_spare_shift; u8 nfi_clk_div; + u8 max_sector; + u32 max_sector_size; }; struct mtk_nfc_bad_mark_ctl { @@ -450,7 +451,7 @@ static inline u8 mtk_nfc_read_byte(struct mtd_info *mtd) * set to max sector to allow the HW to continue reading over * unaligned accesses */ - reg = (MTK_MAX_SECTOR << CON_SEC_SHIFT) | CON_BRD; + reg = (nfc->caps->max_sector << CON_SEC_SHIFT) | CON_BRD; nfi_writel(nfc, reg, NFI_CON); /* trigger to fetch data */ @@ -481,7 +482,7 @@ static void mtk_nfc_write_byte(struct mtd_info *mtd, u8 byte) reg = nfi_readw(nfc, NFI_CNFG) | CNFG_BYTE_RW; nfi_writew(nfc, reg, NFI_CNFG); - reg = MTK_MAX_SECTOR << CON_SEC_SHIFT | CON_BWR; + reg = nfc->caps->max_sector << CON_SEC_SHIFT | CON_BWR; nfi_writel(nfc, reg, NFI_CON); nfi_writew(nfc, STAR_EN, NFI_STRDATA); @@ -1117,9 +1118,11 @@ static void mtk_nfc_set_fdm(struct mtk_nfc_fdm *fdm, struct mtd_info *mtd) { struct nand_chip *nand = mtd_to_nand(mtd); struct mtk_nfc_nand_chip *chip = to_mtk_nand(nand); + struct mtk_nfc *nfc = nand_get_controller_data(nand); u32 ecc_bytes; - ecc_bytes = DIV_ROUND_UP(nand->ecc.strength * ECC_PARITY_BITS, 8); + ecc_bytes = DIV_ROUND_UP(nand->ecc.strength * + mtk_ecc_get_parity_bits(nfc->ecc), 8); fdm->reg_size = chip->spare_per_sector - ecc_bytes; if (fdm->reg_size > NFI_FDM_MAX_SIZE) @@ -1199,7 +1202,8 @@ static int mtk_nfc_ecc_init(struct device *dev, struct mtd_info *mtd) * this controller only supports 512 and 1024 sizes */ if (nand->ecc.size < 1024) { - if (mtd->writesize > 512) { + if (mtd->writesize > 512 && + nfc->caps->max_sector_size > 512) { nand->ecc.size = 1024; nand->ecc.strength <<= 1; } else { @@ -1214,7 +1218,8 @@ static int mtk_nfc_ecc_init(struct device *dev, struct mtd_info *mtd) return ret; /* calculate oob bytes except ecc parity data */ - free = ((nand->ecc.strength * ECC_PARITY_BITS) + 7) >> 3; + free = (nand->ecc.strength * mtk_ecc_get_parity_bits(nfc->ecc) + + 7) >> 3; free = spare - free; /* @@ -1224,10 +1229,12 @@ static int mtk_nfc_ecc_init(struct device *dev, struct mtd_info *mtd) */ if (free > NFI_FDM_MAX_SIZE) { spare -= NFI_FDM_MAX_SIZE; - nand->ecc.strength = (spare << 3) / ECC_PARITY_BITS; + nand->ecc.strength = (spare << 3) / + mtk_ecc_get_parity_bits(nfc->ecc); } else if (free < 0) { spare -= NFI_FDM_MIN_SIZE; - nand->ecc.strength = (spare << 3) / ECC_PARITY_BITS; + nand->ecc.strength = (spare << 3) / + mtk_ecc_get_parity_bits(nfc->ecc); } } @@ -1380,6 +1387,8 @@ static const struct mtk_nfc_caps mtk_nfc_caps_mt2701 = { .num_spare_size = 16, .pageformat_spare_shift = 4, .nfi_clk_div = 1, + .max_sector = 16, + .max_sector_size = 1024, }; static const struct mtk_nfc_caps mtk_nfc_caps_mt2712 = { @@ -1387,6 +1396,8 @@ static const struct mtk_nfc_caps mtk_nfc_caps_mt2712 = { .num_spare_size = 19, .pageformat_spare_shift = 16, .nfi_clk_div = 2, + .max_sector = 16, + .max_sector_size = 1024, }; static const struct of_device_id mtk_nfc_id_table[] = { -- cgit v1.2.3 From 98dea8d71931460c189e5001b0faf2180a42db42 Mon Sep 17 00:00:00 2001 From: RogerCC Lin Date: Thu, 30 Nov 2017 22:10:45 +0800 Subject: mtd: nand: mtk: Support MT7622 NAND flash controller. Add tables to support MT7622 NAND flash controller. Signed-off-by: RogerCC Lin Signed-off-by: Boris Brezillon --- drivers/mtd/nand/mtk_ecc.c | 26 ++++++++++++++++++++++++++ drivers/mtd/nand/mtk_nand.c | 16 ++++++++++++++++ 2 files changed, 42 insertions(+) diff --git a/drivers/mtd/nand/mtk_ecc.c b/drivers/mtd/nand/mtk_ecc.c index 6610eefaa92b..40d86a861a70 100644 --- a/drivers/mtd/nand/mtk_ecc.c +++ b/drivers/mtd/nand/mtk_ecc.c @@ -83,6 +83,10 @@ static const u8 ecc_strength_mt2712[] = { 40, 44, 48, 52, 56, 60, 68, 72, 80 }; +static const u8 ecc_strength_mt7622[] = { + 4, 6, 8, 10, 12, 14, 16 +}; + enum mtk_ecc_regs { ECC_ENCPAR00, ECC_ENCIRQ_EN, @@ -110,6 +114,15 @@ static int mt2712_ecc_regs[] = { [ECC_DECIRQ_STA] = 0x204, }; +static int mt7622_ecc_regs[] = { + [ECC_ENCPAR00] = 0x10, + [ECC_ENCIRQ_EN] = 0x30, + [ECC_ENCIRQ_STA] = 0x34, + [ECC_DECDONE] = 0x11c, + [ECC_DECIRQ_EN] = 0x140, + [ECC_DECIRQ_STA] = 0x144, +}; + static inline void mtk_ecc_wait_idle(struct mtk_ecc *ecc, enum mtk_ecc_operation op) { @@ -458,6 +471,16 @@ static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = { .pg_irq_sel = 1, }; +static const struct mtk_ecc_caps mtk_ecc_caps_mt7622 = { + .err_mask = 0x3f, + .ecc_strength = ecc_strength_mt7622, + .ecc_regs = mt7622_ecc_regs, + .num_ecc_strength = 7, + .ecc_mode_shift = 4, + .parity_bits = 13, + .pg_irq_sel = 0, +}; + static const struct of_device_id mtk_ecc_dt_match[] = { { .compatible = "mediatek,mt2701-ecc", @@ -465,6 +488,9 @@ static const struct of_device_id mtk_ecc_dt_match[] = { }, { .compatible = "mediatek,mt2712-ecc", .data = &mtk_ecc_caps_mt2712, + }, { + .compatible = "mediatek,mt7622-ecc", + .data = &mtk_ecc_caps_mt7622, }, {}, }; diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/mtk_nand.c index b9946ae58616..6977da3a26aa 100644 --- a/drivers/mtd/nand/mtk_nand.c +++ b/drivers/mtd/nand/mtk_nand.c @@ -174,6 +174,10 @@ static const u8 spare_size_mt2712[] = { 74 }; +static const u8 spare_size_mt7622[] = { + 16, 26, 27, 28 +}; + static inline struct mtk_nfc_nand_chip *to_mtk_nand(struct nand_chip *nand) { return container_of(nand, struct mtk_nfc_nand_chip, nand); @@ -1400,6 +1404,15 @@ static const struct mtk_nfc_caps mtk_nfc_caps_mt2712 = { .max_sector_size = 1024, }; +static const struct mtk_nfc_caps mtk_nfc_caps_mt7622 = { + .spare_size = spare_size_mt7622, + .num_spare_size = 4, + .pageformat_spare_shift = 4, + .nfi_clk_div = 1, + .max_sector = 8, + .max_sector_size = 512, +}; + static const struct of_device_id mtk_nfc_id_table[] = { { .compatible = "mediatek,mt2701-nfc", @@ -1407,6 +1420,9 @@ static const struct of_device_id mtk_nfc_id_table[] = { }, { .compatible = "mediatek,mt2712-nfc", .data = &mtk_nfc_caps_mt2712, + }, { + .compatible = "mediatek,mt7622-nfc", + .data = &mtk_nfc_caps_mt7622, }, {} }; -- cgit v1.2.3 From 8c677541bb24871ce44b5a1e327a3e7f5792eae4 Mon Sep 17 00:00:00 2001 From: Boris Brezillon Date: Tue, 5 Dec 2017 12:09:28 +0100 Subject: mtd: nand: denali: Avoid using ecc->code_buf as a temporary buffer ECC bytes are contiguous in the ->oob_poi buffer, which means we don't have to copy them into ->code_buf (here used as a temporary buffer) before passing them to the nand_check_erased_ecc_chunk() function. This change will allow us to allocate ecc->{code,calc}_buf only when ecc->calculate() or ecc->correct() is specified. Signed-off-by: Boris Brezillon Acked-by: Masahiro Yamada --- drivers/mtd/nand/denali.c | 10 +++------- 1 file changed, 3 insertions(+), 7 deletions(-) diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c index 00698b33cb22..313c7f50621b 100644 --- a/drivers/mtd/nand/denali.c +++ b/drivers/mtd/nand/denali.c @@ -330,16 +330,12 @@ static int denali_check_erased_page(struct mtd_info *mtd, unsigned long uncor_ecc_flags, unsigned int max_bitflips) { - uint8_t *ecc_code = chip->ecc.code_buf; + struct denali_nand_info *denali = mtd_to_denali(mtd); + uint8_t *ecc_code = chip->oob_poi + denali->oob_skip_bytes; int ecc_steps = chip->ecc.steps; int ecc_size = chip->ecc.size; int ecc_bytes = chip->ecc.bytes; - int i, ret, stat; - - ret = mtd_ooblayout_get_eccbytes(mtd, ecc_code, chip->oob_poi, 0, - chip->ecc.total); - if (ret) - return ret; + int i, stat; for (i = 0; i < ecc_steps; i++) { if (!(uncor_ecc_flags & BIT(i))) -- cgit v1.2.3 From aeb93af96d0b0f0916aa0f65fe400a1808ea9cb9 Mon Sep 17 00:00:00 2001 From: Boris Brezillon Date: Tue, 5 Dec 2017 12:09:29 +0100 Subject: mtd: nand: Only allocate ecc->{calc, code}_buf when actually needed The only users of the ecc->{calc,code}_buf buffers are NAND controller drivers implementing ecc->calculate() and/or ecc->correct(). Since the ->oobsize can be non-negligle, especially on modern NAND devices, we'd better allocate it only when it is actually required. Make ecc->{calc,code}_buf allocation dependent on the presence of ecc->calculate() or ecc->correct(). Signed-off-by: Boris Brezillon Reviewed-by: Masahiro Yamada --- drivers/mtd/nand/nand_base.c | 25 +++++++++++-------------- 1 file changed, 11 insertions(+), 14 deletions(-) diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 32c0239b380a..84d0a5d67e33 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -5318,21 +5318,9 @@ int nand_scan_tail(struct mtd_info *mtd) return -EINVAL; } - ecc->calc_buf = kmalloc(mtd->oobsize, GFP_KERNEL); - if (!ecc->calc_buf) - return -ENOMEM; - - ecc->code_buf = kmalloc(mtd->oobsize, GFP_KERNEL); - if (!ecc->code_buf) { - ret = -ENOMEM; - goto err_free_buf; - } - chip->data_buf = kmalloc(mtd->writesize + mtd->oobsize, GFP_KERNEL); - if (!chip->data_buf) { - ret = -ENOMEM; - goto err_free_buf; - } + if (!chip->data_buf) + return -ENOMEM; /* * FIXME: some NAND manufacturer drivers expect the first die to be @@ -5495,6 +5483,15 @@ int nand_scan_tail(struct mtd_info *mtd) goto err_nand_manuf_cleanup; } + if (ecc->correct || ecc->calculate) { + ecc->calc_buf = kmalloc(mtd->oobsize, GFP_KERNEL); + ecc->code_buf = kmalloc(mtd->oobsize, GFP_KERNEL); + if (!ecc->calc_buf || !ecc->code_buf) { + ret = -ENOMEM; + goto err_nand_manuf_cleanup; + } + } + /* For many systems, the standard OOB write also works for raw */ if (!ecc->read_oob_raw) ecc->read_oob_raw = ecc->read_oob; -- cgit v1.2.3 From 707d81545dbc3d3ee4ae093fc600831eb97302e7 Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Thu, 7 Dec 2017 10:33:58 +0100 Subject: mtd: nand: samsung: add ECC requirements for K9F4G08U0D Samsung NAND chip K9F4G08U0D minimum ECC strength requirement is 1 bit per 512 bytes. As the chip is not ONFI nor JEDEC and because of the lack of these values, boards using it fail to probe the NAND controller driver. Fix this by setting up the default values. Signed-off-by: Miquel Raynal Signed-off-by: Boris Brezillon --- drivers/mtd/nand/nand_samsung.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/mtd/nand/nand_samsung.c b/drivers/mtd/nand/nand_samsung.c index d348f0129ae7..f6b0a63a068c 100644 --- a/drivers/mtd/nand/nand_samsung.c +++ b/drivers/mtd/nand/nand_samsung.c @@ -91,6 +91,12 @@ static void samsung_nand_decode_id(struct nand_chip *chip) } } else { nand_decode_ext_id(chip); + + /* Datasheet values for SLC Samsung K9F4G08U0D-S[I|C]B0(T00) */ + if (nand_is_slc(chip) && chip->id.data[1] == 0xDC) { + chip->ecc_step_ds = 512; + chip->ecc_strength_ds = 1; + } } } -- cgit v1.2.3 From 8878b126df769831cb2fa4088c3806538e8305f5 Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Thu, 9 Nov 2017 14:16:45 +0100 Subject: mtd: nand: add ->exec_op() implementation Introduce a new interface to instruct NAND controllers to send specific NAND operations. The new interface takes the form of a single method called ->exec_op(). This method is designed to replace ->cmd_ctrl(), ->cmdfunc() and ->read/write_byte/word/buf() hooks. ->exec_op() is passed a set of instructions describing the operation to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY) and delay. The delay is here to help simple controllers wait enough time between each instruction, advanced controllers with integrated timings control can ignore these delays. Controllers that natively support complex operations (operations formed of several instructions) can use the NAND op parser infrastructure. This infrastructure allows controller drivers to describe the sequence of instructions they support (called nand_op_pattern) and a hook for each of these supported sequences. The core then tries to find the best match for a given NAND operation, and calls the associated hook. Various other helpers are also added to ease NAND controller drivers writing. This new interface should ease support of vendor specific operations in that NAND manufacturer drivers now have a way to check if the controller they are connected to supports a specific operation, and complain or refuse to probe the NAND chip when that's not the case. Suggested-by: Boris Brezillon Signed-off-by: Miquel Raynal Signed-off-by: Boris Brezillon --- drivers/mtd/nand/nand_base.c | 1013 ++++++++++++++++++++++++++++++++++++++++- drivers/mtd/nand/nand_hynix.c | 9 + include/linux/mtd/rawnand.h | 368 ++++++++++++++- 3 files changed, 1364 insertions(+), 26 deletions(-) diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 84d0a5d67e33..ab8ad9e8a8d8 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -688,6 +688,66 @@ static void nand_wait_status_ready(struct mtd_info *mtd, unsigned long timeo) } while (time_before(jiffies, timeo)); }; +/** + * nand_soft_waitrdy - Poll STATUS reg until RDY bit is set to 1 + * @chip: NAND chip structure + * @timeout_ms: Timeout in ms + * + * Poll the STATUS register using ->exec_op() until the RDY bit becomes 1. + * If that does not happen whitin the specified timeout, -ETIMEDOUT is + * returned. + * + * This helper is intended to be used when the controller does not have access + * to the NAND R/B pin. + * + * Be aware that calling this helper from an ->exec_op() implementation means + * ->exec_op() must be re-entrant. + * + * Return 0 if the NAND chip is ready, a negative error otherwise. + */ +int nand_soft_waitrdy(struct nand_chip *chip, unsigned long timeout_ms) +{ + u8 status = 0; + int ret; + + if (!chip->exec_op) + return -ENOTSUPP; + + ret = nand_status_op(chip, NULL); + if (ret) + return ret; + + timeout_ms = jiffies + msecs_to_jiffies(timeout_ms); + do { + ret = nand_read_data_op(chip, &status, sizeof(status), true); + if (ret) + break; + + if (status & NAND_STATUS_READY) + break; + + /* + * Typical lowest execution time for a tR on most NANDs is 10us, + * use this as polling delay before doing something smarter (ie. + * deriving a delay from the timeout value, timeout_ms/ratio). + */ + udelay(10); + } while (time_before(jiffies, timeout_ms)); + + /* + * We have to exit READ_STATUS mode in order to read real data on the + * bus in case the WAITRDY instruction is preceding a DATA_IN + * instruction. + */ + nand_exit_status_op(chip); + + if (ret) + return ret; + + return status & NAND_STATUS_READY ? 0 : -ETIMEDOUT; +}; +EXPORT_SYMBOL_GPL(nand_soft_waitrdy); + /** * nand_command - [DEFAULT] Send command to NAND device * @mtd: MTD device structure @@ -1237,6 +1297,140 @@ static int nand_init_data_interface(struct nand_chip *chip) return 0; } +/** + * nand_fill_column_cycles - fill the column cycles of an address + * @chip: The NAND chip + * @addrs: Array of address cycles to fill + * @offset_in_page: The offset in the page + * + * Fills the first or the first two bytes of the @addrs field depending + * on the NAND bus width and the page size. + * + * Returns the number of cycles needed to encode the column, or a negative + * error code in case one of the arguments is invalid. + */ +static int nand_fill_column_cycles(struct nand_chip *chip, u8 *addrs, + unsigned int offset_in_page) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + + /* Make sure the offset is less than the actual page size. */ + if (offset_in_page > mtd->writesize + mtd->oobsize) + return -EINVAL; + + /* + * On small page NANDs, there's a dedicated command to access the OOB + * area, and the column address is relative to the start of the OOB + * area, not the start of the page. Asjust the address accordingly. + */ + if (mtd->writesize <= 512 && offset_in_page >= mtd->writesize) + offset_in_page -= mtd->writesize; + + /* + * The offset in page is expressed in bytes, if the NAND bus is 16-bit + * wide, then it must be divided by 2. + */ + if (chip->options & NAND_BUSWIDTH_16) { + if (WARN_ON(offset_in_page % 2)) + return -EINVAL; + + offset_in_page /= 2; + } + + addrs[0] = offset_in_page; + + /* + * Small page NANDs use 1 cycle for the columns, while large page NANDs + * need 2 + */ + if (mtd->writesize <= 512) + return 1; + + addrs[1] = offset_in_page >> 8; + + return 2; +} + +static int nand_sp_exec_read_page_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, void *buf, + unsigned int len) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + u8 addrs[4]; + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_READ0, 0), + NAND_OP_ADDR(3, addrs, PSEC_TO_NSEC(sdr->tWB_max)), + NAND_OP_WAIT_RDY(PSEC_TO_MSEC(sdr->tR_max), + PSEC_TO_NSEC(sdr->tRR_min)), + NAND_OP_DATA_IN(len, buf, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + int ret; + + /* Drop the DATA_IN instruction if len is set to 0. */ + if (!len) + op.ninstrs--; + + if (offset_in_page >= mtd->writesize) + instrs[0].ctx.cmd.opcode = NAND_CMD_READOOB; + else if (offset_in_page >= 256 && + !(chip->options & NAND_BUSWIDTH_16)) + instrs[0].ctx.cmd.opcode = NAND_CMD_READ1; + + ret = nand_fill_column_cycles(chip, addrs, offset_in_page); + if (ret < 0) + return ret; + + addrs[1] = page; + addrs[2] = page >> 8; + + if (chip->options & NAND_ROW_ADDR_3) { + addrs[3] = page >> 16; + instrs[1].ctx.addr.naddrs++; + } + + return nand_exec_op(chip, &op); +} + +static int nand_lp_exec_read_page_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, void *buf, + unsigned int len) +{ + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + u8 addrs[5]; + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_READ0, 0), + NAND_OP_ADDR(4, addrs, 0), + NAND_OP_CMD(NAND_CMD_READSTART, PSEC_TO_NSEC(sdr->tWB_max)), + NAND_OP_WAIT_RDY(PSEC_TO_MSEC(sdr->tR_max), + PSEC_TO_NSEC(sdr->tRR_min)), + NAND_OP_DATA_IN(len, buf, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + int ret; + + /* Drop the DATA_IN instruction if len is set to 0. */ + if (!len) + op.ninstrs--; + + ret = nand_fill_column_cycles(chip, addrs, offset_in_page); + if (ret < 0) + return ret; + + addrs[2] = page; + addrs[3] = page >> 8; + + if (chip->options & NAND_ROW_ADDR_3) { + addrs[4] = page >> 16; + instrs[1].ctx.addr.naddrs++; + } + + return nand_exec_op(chip, &op); +} + /** * nand_read_page_op - Do a READ PAGE operation * @chip: The NAND chip @@ -1261,6 +1455,16 @@ int nand_read_page_op(struct nand_chip *chip, unsigned int page, if (offset_in_page + len > mtd->writesize + mtd->oobsize) return -EINVAL; + if (chip->exec_op) { + if (mtd->writesize > 512) + return nand_lp_exec_read_page_op(chip, page, + offset_in_page, buf, + len); + + return nand_sp_exec_read_page_op(chip, page, offset_in_page, + buf, len); + } + chip->cmdfunc(mtd, NAND_CMD_READ0, offset_in_page, page); if (len) chip->read_buf(mtd, buf, len); @@ -1291,6 +1495,25 @@ static int nand_read_param_page_op(struct nand_chip *chip, u8 page, void *buf, if (len && !buf) return -EINVAL; + if (chip->exec_op) { + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_PARAM, 0), + NAND_OP_ADDR(1, &page, PSEC_TO_NSEC(sdr->tWB_max)), + NAND_OP_WAIT_RDY(PSEC_TO_MSEC(sdr->tR_max), + PSEC_TO_NSEC(sdr->tRR_min)), + NAND_OP_8BIT_DATA_IN(len, buf, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + + /* Drop the DATA_IN instruction if len is set to 0. */ + if (!len) + op.ninstrs--; + + return nand_exec_op(chip, &op); + } + chip->cmdfunc(mtd, NAND_CMD_PARAM, page, -1); for (i = 0; i < len; i++) p[i] = chip->read_byte(mtd); @@ -1323,6 +1546,37 @@ int nand_change_read_column_op(struct nand_chip *chip, if (offset_in_page + len > mtd->writesize + mtd->oobsize) return -EINVAL; + /* Small page NANDs do not support column change. */ + if (mtd->writesize <= 512) + return -ENOTSUPP; + + if (chip->exec_op) { + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + u8 addrs[2] = {}; + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_RNDOUT, 0), + NAND_OP_ADDR(2, addrs, 0), + NAND_OP_CMD(NAND_CMD_RNDOUTSTART, + PSEC_TO_NSEC(sdr->tCCS_min)), + NAND_OP_DATA_IN(len, buf, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + int ret; + + ret = nand_fill_column_cycles(chip, addrs, offset_in_page); + if (ret < 0) + return ret; + + /* Drop the DATA_IN instruction if len is set to 0. */ + if (!len) + op.ninstrs--; + + instrs[3].ctx.data.force_8bit = force_8bit; + + return nand_exec_op(chip, &op); + } + chip->cmdfunc(mtd, NAND_CMD_RNDOUT, offset_in_page, -1); if (len) chip->read_buf(mtd, buf, len); @@ -1355,6 +1609,11 @@ int nand_read_oob_op(struct nand_chip *chip, unsigned int page, if (offset_in_oob + len > mtd->oobsize) return -EINVAL; + if (chip->exec_op) + return nand_read_page_op(chip, page, + mtd->writesize + offset_in_oob, + buf, len); + chip->cmdfunc(mtd, NAND_CMD_READOOB, offset_in_oob, page); if (len) chip->read_buf(mtd, buf, len); @@ -1363,6 +1622,81 @@ int nand_read_oob_op(struct nand_chip *chip, unsigned int page, } EXPORT_SYMBOL_GPL(nand_read_oob_op); +static int nand_exec_prog_page_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, const void *buf, + unsigned int len, bool prog) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + u8 addrs[5] = {}; + struct nand_op_instr instrs[] = { + /* + * The first instruction will be dropped if we're dealing + * with a large page NAND and adjusted if we're dealing + * with a small page NAND and the page offset is > 255. + */ + NAND_OP_CMD(NAND_CMD_READ0, 0), + NAND_OP_CMD(NAND_CMD_SEQIN, 0), + NAND_OP_ADDR(0, addrs, PSEC_TO_NSEC(sdr->tADL_min)), + NAND_OP_DATA_OUT(len, buf, 0), + NAND_OP_CMD(NAND_CMD_PAGEPROG, PSEC_TO_NSEC(sdr->tWB_max)), + NAND_OP_WAIT_RDY(PSEC_TO_MSEC(sdr->tPROG_max), 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + int naddrs = nand_fill_column_cycles(chip, addrs, offset_in_page); + int ret; + u8 status; + + if (naddrs < 0) + return naddrs; + + addrs[naddrs++] = page; + addrs[naddrs++] = page >> 8; + if (chip->options & NAND_ROW_ADDR_3) + addrs[naddrs++] = page >> 16; + + instrs[2].ctx.addr.naddrs = naddrs; + + /* Drop the last two instructions if we're not programming the page. */ + if (!prog) { + op.ninstrs -= 2; + /* Also drop the DATA_OUT instruction if empty. */ + if (!len) + op.ninstrs--; + } + + if (mtd->writesize <= 512) { + /* + * Small pages need some more tweaking: we have to adjust the + * first instruction depending on the page offset we're trying + * to access. + */ + if (offset_in_page >= mtd->writesize) + instrs[0].ctx.cmd.opcode = NAND_CMD_READOOB; + else if (offset_in_page >= 256 && + !(chip->options & NAND_BUSWIDTH_16)) + instrs[0].ctx.cmd.opcode = NAND_CMD_READ1; + } else { + /* + * Drop the first command if we're dealing with a large page + * NAND. + */ + op.instrs++; + op.ninstrs--; + } + + ret = nand_exec_op(chip, &op); + if (!prog || ret) + return ret; + + ret = nand_status_op(chip, &status); + if (ret) + return ret; + + return status; +} + /** * nand_prog_page_begin_op - starts a PROG PAGE operation * @chip: The NAND chip @@ -1388,6 +1722,10 @@ int nand_prog_page_begin_op(struct nand_chip *chip, unsigned int page, if (offset_in_page + len > mtd->writesize + mtd->oobsize) return -EINVAL; + if (chip->exec_op) + return nand_exec_prog_page_op(chip, page, offset_in_page, buf, + len, false); + chip->cmdfunc(mtd, NAND_CMD_SEQIN, offset_in_page, page); if (buf) @@ -1409,11 +1747,35 @@ EXPORT_SYMBOL_GPL(nand_prog_page_begin_op); int nand_prog_page_end_op(struct nand_chip *chip) { struct mtd_info *mtd = nand_to_mtd(chip); - int status; + int ret; + u8 status; - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + if (chip->exec_op) { + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_PAGEPROG, + PSEC_TO_NSEC(sdr->tWB_max)), + NAND_OP_WAIT_RDY(PSEC_TO_MSEC(sdr->tPROG_max), 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + + ret = nand_exec_op(chip, &op); + if (ret) + return ret; + + ret = nand_status_op(chip, &status); + if (ret) + return ret; + } else { + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + ret = chip->waitfunc(mtd, chip); + if (ret < 0) + return ret; + + status = ret; + } - status = chip->waitfunc(mtd, chip); if (status & NAND_STATUS_FAIL) return -EIO; @@ -1447,11 +1809,16 @@ int nand_prog_page_op(struct nand_chip *chip, unsigned int page, if (offset_in_page + len > mtd->writesize + mtd->oobsize) return -EINVAL; - chip->cmdfunc(mtd, NAND_CMD_SEQIN, offset_in_page, page); - chip->write_buf(mtd, buf, len); - chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + if (chip->exec_op) { + status = nand_exec_prog_page_op(chip, page, offset_in_page, buf, + len, true); + } else { + chip->cmdfunc(mtd, NAND_CMD_SEQIN, offset_in_page, page); + chip->write_buf(mtd, buf, len); + chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); + status = chip->waitfunc(mtd, chip); + } - status = chip->waitfunc(mtd, chip); if (status & NAND_STATUS_FAIL) return -EIO; @@ -1485,6 +1852,35 @@ int nand_change_write_column_op(struct nand_chip *chip, if (offset_in_page + len > mtd->writesize + mtd->oobsize) return -EINVAL; + /* Small page NANDs do not support column change. */ + if (mtd->writesize <= 512) + return -ENOTSUPP; + + if (chip->exec_op) { + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + u8 addrs[2]; + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_RNDIN, 0), + NAND_OP_ADDR(2, addrs, PSEC_TO_NSEC(sdr->tCCS_min)), + NAND_OP_DATA_OUT(len, buf, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + int ret; + + ret = nand_fill_column_cycles(chip, addrs, offset_in_page); + if (ret < 0) + return ret; + + instrs[2].ctx.data.force_8bit = force_8bit; + + /* Drop the DATA_OUT instruction if len is set to 0. */ + if (!len) + op.ninstrs--; + + return nand_exec_op(chip, &op); + } + chip->cmdfunc(mtd, NAND_CMD_RNDIN, offset_in_page, -1); if (len) chip->write_buf(mtd, buf, len); @@ -1516,6 +1912,23 @@ int nand_readid_op(struct nand_chip *chip, u8 addr, void *buf, if (len && !buf) return -EINVAL; + if (chip->exec_op) { + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_READID, 0), + NAND_OP_ADDR(1, &addr, PSEC_TO_NSEC(sdr->tADL_min)), + NAND_OP_8BIT_DATA_IN(len, buf, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + + /* Drop the DATA_IN instruction if len is set to 0. */ + if (!len) + op.ninstrs--; + + return nand_exec_op(chip, &op); + } + chip->cmdfunc(mtd, NAND_CMD_READID, addr, -1); for (i = 0; i < len; i++) @@ -1540,6 +1953,22 @@ int nand_status_op(struct nand_chip *chip, u8 *status) { struct mtd_info *mtd = nand_to_mtd(chip); + if (chip->exec_op) { + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_STATUS, + PSEC_TO_NSEC(sdr->tADL_min)), + NAND_OP_8BIT_DATA_IN(1, status, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + + if (!status) + op.ninstrs--; + + return nand_exec_op(chip, &op); + } + chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); if (status) *status = chip->read_byte(mtd); @@ -1563,6 +1992,15 @@ int nand_exit_status_op(struct nand_chip *chip) { struct mtd_info *mtd = nand_to_mtd(chip); + if (chip->exec_op) { + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_READ0, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + + return nand_exec_op(chip, &op); + } + chip->cmdfunc(mtd, NAND_CMD_READ0, -1, -1); return 0; @@ -1585,14 +2023,42 @@ int nand_erase_op(struct nand_chip *chip, unsigned int eraseblock) struct mtd_info *mtd = nand_to_mtd(chip); unsigned int page = eraseblock << (chip->phys_erase_shift - chip->page_shift); - int status; + int ret; + u8 status; - chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); - chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); + if (chip->exec_op) { + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + u8 addrs[3] = { page, page >> 8, page >> 16 }; + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_ERASE1, 0), + NAND_OP_ADDR(2, addrs, 0), + NAND_OP_CMD(NAND_CMD_ERASE2, + PSEC_TO_MSEC(sdr->tWB_max)), + NAND_OP_WAIT_RDY(PSEC_TO_MSEC(sdr->tBERS_max), 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); - status = chip->waitfunc(mtd, chip); - if (status < 0) - return status; + if (chip->options & NAND_ROW_ADDR_3) + instrs[1].ctx.addr.naddrs++; + + ret = nand_exec_op(chip, &op); + if (ret) + return ret; + + ret = nand_status_op(chip, &status); + if (ret) + return ret; + } else { + chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); + chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); + + ret = chip->waitfunc(mtd, chip); + if (ret < 0) + return ret; + + status = ret; + } if (status & NAND_STATUS_FAIL) return -EIO; @@ -1618,13 +2084,40 @@ static int nand_set_features_op(struct nand_chip *chip, u8 feature, { struct mtd_info *mtd = nand_to_mtd(chip); const u8 *params = data; - int i, status; + int i, ret; + u8 status; - chip->cmdfunc(mtd, NAND_CMD_SET_FEATURES, feature, -1); - for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) - chip->write_byte(mtd, params[i]); + if (chip->exec_op) { + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_SET_FEATURES, 0), + NAND_OP_ADDR(1, &feature, PSEC_TO_NSEC(sdr->tADL_min)), + NAND_OP_8BIT_DATA_OUT(ONFI_SUBFEATURE_PARAM_LEN, data, + PSEC_TO_NSEC(sdr->tWB_max)), + NAND_OP_WAIT_RDY(PSEC_TO_MSEC(sdr->tFEAT_max), 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + + ret = nand_exec_op(chip, &op); + if (ret) + return ret; + + ret = nand_status_op(chip, &status); + if (ret) + return ret; + } else { + chip->cmdfunc(mtd, NAND_CMD_SET_FEATURES, feature, -1); + for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) + chip->write_byte(mtd, params[i]); + + ret = chip->waitfunc(mtd, chip); + if (ret < 0) + return ret; + + status = ret; + } - status = chip->waitfunc(mtd, chip); if (status & NAND_STATUS_FAIL) return -EIO; @@ -1650,6 +2143,22 @@ static int nand_get_features_op(struct nand_chip *chip, u8 feature, u8 *params = data; int i; + if (chip->exec_op) { + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_GET_FEATURES, 0), + NAND_OP_ADDR(1, &feature, PSEC_TO_NSEC(sdr->tWB_max)), + NAND_OP_WAIT_RDY(PSEC_TO_MSEC(sdr->tFEAT_max), + PSEC_TO_NSEC(sdr->tRR_min)), + NAND_OP_8BIT_DATA_IN(ONFI_SUBFEATURE_PARAM_LEN, + data, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + + return nand_exec_op(chip, &op); + } + chip->cmdfunc(mtd, NAND_CMD_GET_FEATURES, feature, -1); for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i) params[i] = chip->read_byte(mtd); @@ -1671,6 +2180,18 @@ int nand_reset_op(struct nand_chip *chip) { struct mtd_info *mtd = nand_to_mtd(chip); + if (chip->exec_op) { + const struct nand_sdr_timings *sdr = + nand_get_sdr_timings(&chip->data_interface); + struct nand_op_instr instrs[] = { + NAND_OP_CMD(NAND_CMD_RESET, PSEC_TO_NSEC(sdr->tWB_max)), + NAND_OP_WAIT_RDY(PSEC_TO_MSEC(sdr->tRST_max), 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + + return nand_exec_op(chip, &op); + } + chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); return 0; @@ -1698,6 +2219,17 @@ int nand_read_data_op(struct nand_chip *chip, void *buf, unsigned int len, if (!len || !buf) return -EINVAL; + if (chip->exec_op) { + struct nand_op_instr instrs[] = { + NAND_OP_DATA_IN(len, buf, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + + instrs[0].ctx.data.force_8bit = force_8bit; + + return nand_exec_op(chip, &op); + } + if (force_8bit) { u8 *p = buf; unsigned int i; @@ -1733,6 +2265,17 @@ int nand_write_data_op(struct nand_chip *chip, const void *buf, if (!len || !buf) return -EINVAL; + if (chip->exec_op) { + struct nand_op_instr instrs[] = { + NAND_OP_DATA_OUT(len, buf, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + + instrs[0].ctx.data.force_8bit = force_8bit; + + return nand_exec_op(chip, &op); + } + if (force_8bit) { const u8 *p = buf; unsigned int i; @@ -1747,6 +2290,420 @@ int nand_write_data_op(struct nand_chip *chip, const void *buf, } EXPORT_SYMBOL_GPL(nand_write_data_op); +/** + * struct nand_op_parser_ctx - Context used by the parser + * @instrs: array of all the instructions that must be addressed + * @ninstrs: length of the @instrs array + * @subop: Sub-operation to be passed to the NAND controller + * + * This structure is used by the core to split NAND operations into + * sub-operations that can be handled by the NAND controller. + */ +struct nand_op_parser_ctx { + const struct nand_op_instr *instrs; + unsigned int ninstrs; + struct nand_subop subop; +}; + +/** + * nand_op_parser_must_split_instr - Checks if an instruction must be split + * @pat: the parser pattern element that matches @instr + * @instr: pointer to the instruction to check + * @start_offset: this is an in/out parameter. If @instr has already been + * split, then @start_offset is the offset from which to start + * (either an address cycle or an offset in the data buffer). + * Conversely, if the function returns true (ie. instr must be + * split), this parameter is updated to point to the first + * data/address cycle that has not been taken care of. + * + * Some NAND controllers are limited and cannot send X address cycles with a + * unique operation, or cannot read/write more than Y bytes at the same time. + * In this case, split the instruction that does not fit in a single + * controller-operation into two or more chunks. + * + * Returns true if the instruction must be split, false otherwise. + * The @start_offset parameter is also updated to the offset at which the next + * bundle of instruction must start (if an address or a data instruction). + */ +static bool +nand_op_parser_must_split_instr(const struct nand_op_parser_pattern_elem *pat, + const struct nand_op_instr *instr, + unsigned int *start_offset) +{ + switch (pat->type) { + case NAND_OP_ADDR_INSTR: + if (!pat->addr.maxcycles) + break; + + if (instr->ctx.addr.naddrs - *start_offset > + pat->addr.maxcycles) { + *start_offset += pat->addr.maxcycles; + return true; + } + break; + + case NAND_OP_DATA_IN_INSTR: + case NAND_OP_DATA_OUT_INSTR: + if (!pat->data.maxlen) + break; + + if (instr->ctx.data.len - *start_offset > pat->data.maxlen) { + *start_offset += pat->data.maxlen; + return true; + } + break; + + default: + break; + } + + return false; +} + +/** + * nand_op_parser_match_pat - Checks if a pattern matches the instructions + * remaining in the parser context + * @pat: the pattern to test + * @ctx: the parser context structure to match with the pattern @pat + * + * Check if @pat matches the set or a sub-set of instructions remaining in @ctx. + * Returns true if this is the case, false ortherwise. When true is returned, + * @ctx->subop is updated with the set of instructions to be passed to the + * controller driver. + */ +static bool +nand_op_parser_match_pat(const struct nand_op_parser_pattern *pat, + struct nand_op_parser_ctx *ctx) +{ + unsigned int instr_offset = ctx->subop.first_instr_start_off; + const struct nand_op_instr *end = ctx->instrs + ctx->ninstrs; + const struct nand_op_instr *instr = ctx->subop.instrs; + unsigned int i, ninstrs; + + for (i = 0, ninstrs = 0; i < pat->nelems && instr < end; i++) { + /* + * The pattern instruction does not match the operation + * instruction. If the instruction is marked optional in the + * pattern definition, we skip the pattern element and continue + * to the next one. If the element is mandatory, there's no + * match and we can return false directly. + */ + if (instr->type != pat->elems[i].type) { + if (!pat->elems[i].optional) + return false; + + continue; + } + + /* + * Now check the pattern element constraints. If the pattern is + * not able to handle the whole instruction in a single step, + * we have to split it. + * The last_instr_end_off value comes back updated to point to + * the position where we have to split the instruction (the + * start of the next subop chunk). + */ + if (nand_op_parser_must_split_instr(&pat->elems[i], instr, + &instr_offset)) { + ninstrs++; + i++; + break; + } + + instr++; + ninstrs++; + instr_offset = 0; + } + + /* + * This can happen if all instructions of a pattern are optional. + * Still, if there's not at least one instruction handled by this + * pattern, this is not a match, and we should try the next one (if + * any). + */ + if (!ninstrs) + return false; + + /* + * We had a match on the pattern head, but the pattern may be longer + * than the instructions we're asked to execute. We need to make sure + * there's no mandatory elements in the pattern tail. + */ + for (; i < pat->nelems; i++) { + if (!pat->elems[i].optional) + return false; + } + + /* + * We have a match: update the subop structure accordingly and return + * true. + */ + ctx->subop.ninstrs = ninstrs; + ctx->subop.last_instr_end_off = instr_offset; + + return true; +} + +#if IS_ENABLED(CONFIG_DYNAMIC_DEBUG) || defined(DEBUG) +static void nand_op_parser_trace(const struct nand_op_parser_ctx *ctx) +{ + const struct nand_op_instr *instr; + char *prefix = " "; + unsigned int i; + + pr_debug("executing subop:\n"); + + for (i = 0; i < ctx->ninstrs; i++) { + instr = &ctx->instrs[i]; + + if (instr == &ctx->subop.instrs[0]) + prefix = " ->"; + + switch (instr->type) { + case NAND_OP_CMD_INSTR: + pr_debug("%sCMD [0x%02x]\n", prefix, + instr->ctx.cmd.opcode); + break; + case NAND_OP_ADDR_INSTR: + pr_debug("%sADDR [%d cyc: %*ph]\n", prefix, + instr->ctx.addr.naddrs, + instr->ctx.addr.naddrs < 64 ? + instr->ctx.addr.naddrs : 64, + instr->ctx.addr.addrs); + break; + case NAND_OP_DATA_IN_INSTR: + pr_debug("%sDATA_IN [%d B%s]\n", prefix, + instr->ctx.data.len, + instr->ctx.data.force_8bit ? + ", force 8-bit" : ""); + break; + case NAND_OP_DATA_OUT_INSTR: + pr_debug("%sDATA_OUT [%d B%s]\n", prefix, + instr->ctx.data.len, + instr->ctx.data.force_8bit ? + ", force 8-bit" : ""); + break; + case NAND_OP_WAITRDY_INSTR: + pr_debug("%sWAITRDY [max %d ms]\n", prefix, + instr->ctx.waitrdy.timeout_ms); + break; + } + + if (instr == &ctx->subop.instrs[ctx->subop.ninstrs - 1]) + prefix = " "; + } +} +#else +static void nand_op_parser_trace(const struct nand_op_parser_ctx *ctx) +{ + /* NOP */ +} +#endif + +/** + * nand_op_parser_exec_op - exec_op parser + * @chip: the NAND chip + * @parser: patterns description provided by the controller driver + * @op: the NAND operation to address + * @check_only: when true, the function only checks if @op can be handled but + * does not execute the operation + * + * Helper function designed to ease integration of NAND controller drivers that + * only support a limited set of instruction sequences. The supported sequences + * are described in @parser, and the framework takes care of splitting @op into + * multiple sub-operations (if required) and pass them back to the ->exec() + * callback of the matching pattern if @check_only is set to false. + * + * NAND controller drivers should call this function from their own ->exec_op() + * implementation. + * + * Returns 0 on success, a negative error code otherwise. A failure can be + * caused by an unsupported operation (none of the supported patterns is able + * to handle the requested operation), or an error returned by one of the + * matching pattern->exec() hook. + */ +int nand_op_parser_exec_op(struct nand_chip *chip, + const struct nand_op_parser *parser, + const struct nand_operation *op, bool check_only) +{ + struct nand_op_parser_ctx ctx = { + .subop.instrs = op->instrs, + .instrs = op->instrs, + .ninstrs = op->ninstrs, + }; + unsigned int i; + + while (ctx.subop.instrs < op->instrs + op->ninstrs) { + int ret; + + for (i = 0; i < parser->npatterns; i++) { + const struct nand_op_parser_pattern *pattern; + + pattern = &parser->patterns[i]; + if (!nand_op_parser_match_pat(pattern, &ctx)) + continue; + + nand_op_parser_trace(&ctx); + + if (check_only) + break; + + ret = pattern->exec(chip, &ctx.subop); + if (ret) + return ret; + + break; + } + + if (i == parser->npatterns) { + pr_debug("->exec_op() parser: pattern not found!\n"); + return -ENOTSUPP; + } + + /* + * Update the context structure by pointing to the start of the + * next subop. + */ + ctx.subop.instrs = ctx.subop.instrs + ctx.subop.ninstrs; + if (ctx.subop.last_instr_end_off) + ctx.subop.instrs -= 1; + + ctx.subop.first_instr_start_off = ctx.subop.last_instr_end_off; + } + + return 0; +} +EXPORT_SYMBOL_GPL(nand_op_parser_exec_op); + +static bool nand_instr_is_data(const struct nand_op_instr *instr) +{ + return instr && (instr->type == NAND_OP_DATA_IN_INSTR || + instr->type == NAND_OP_DATA_OUT_INSTR); +} + +static bool nand_subop_instr_is_valid(const struct nand_subop *subop, + unsigned int instr_idx) +{ + return subop && instr_idx < subop->ninstrs; +} + +static int nand_subop_get_start_off(const struct nand_subop *subop, + unsigned int instr_idx) +{ + if (instr_idx) + return 0; + + return subop->first_instr_start_off; +} + +/** + * nand_subop_get_addr_start_off - Get the start offset in an address array + * @subop: The entire sub-operation + * @instr_idx: Index of the instruction inside the sub-operation + * + * During driver development, one could be tempted to directly use the + * ->addr.addrs field of address instructions. This is wrong as address + * instructions might be split. + * + * Given an address instruction, returns the offset of the first cycle to issue. + */ +int nand_subop_get_addr_start_off(const struct nand_subop *subop, + unsigned int instr_idx) +{ + if (!nand_subop_instr_is_valid(subop, instr_idx) || + subop->instrs[instr_idx].type != NAND_OP_ADDR_INSTR) + return -EINVAL; + + return nand_subop_get_start_off(subop, instr_idx); +} +EXPORT_SYMBOL_GPL(nand_subop_get_addr_start_off); + +/** + * nand_subop_get_num_addr_cyc - Get the remaining address cycles to assert + * @subop: The entire sub-operation + * @instr_idx: Index of the instruction inside the sub-operation + * + * During driver development, one could be tempted to directly use the + * ->addr->naddrs field of a data instruction. This is wrong as instructions + * might be split. + * + * Given an address instruction, returns the number of address cycle to issue. + */ +int nand_subop_get_num_addr_cyc(const struct nand_subop *subop, + unsigned int instr_idx) +{ + int start_off, end_off; + + if (!nand_subop_instr_is_valid(subop, instr_idx) || + subop->instrs[instr_idx].type != NAND_OP_ADDR_INSTR) + return -EINVAL; + + start_off = nand_subop_get_addr_start_off(subop, instr_idx); + + if (instr_idx == subop->ninstrs - 1 && + subop->last_instr_end_off) + end_off = subop->last_instr_end_off; + else + end_off = subop->instrs[instr_idx].ctx.addr.naddrs; + + return end_off - start_off; +} +EXPORT_SYMBOL_GPL(nand_subop_get_num_addr_cyc); + +/** + * nand_subop_get_data_start_off - Get the start offset in a data array + * @subop: The entire sub-operation + * @instr_idx: Index of the instruction inside the sub-operation + * + * During driver development, one could be tempted to directly use the + * ->data->buf.{in,out} field of data instructions. This is wrong as data + * instructions might be split. + * + * Given a data instruction, returns the offset to start from. + */ +int nand_subop_get_data_start_off(const struct nand_subop *subop, + unsigned int instr_idx) +{ + if (!nand_subop_instr_is_valid(subop, instr_idx) || + !nand_instr_is_data(&subop->instrs[instr_idx])) + return -EINVAL; + + return nand_subop_get_start_off(subop, instr_idx); +} +EXPORT_SYMBOL_GPL(nand_subop_get_data_start_off); + +/** + * nand_subop_get_data_len - Get the number of bytes to retrieve + * @subop: The entire sub-operation + * @instr_idx: Index of the instruction inside the sub-operation + * + * During driver development, one could be tempted to directly use the + * ->data->len field of a data instruction. This is wrong as data instructions + * might be split. + * + * Returns the length of the chunk of data to send/receive. + */ +int nand_subop_get_data_len(const struct nand_subop *subop, + unsigned int instr_idx) +{ + int start_off = 0, end_off; + + if (!nand_subop_instr_is_valid(subop, instr_idx) || + !nand_instr_is_data(&subop->instrs[instr_idx])) + return -EINVAL; + + start_off = nand_subop_get_data_start_off(subop, instr_idx); + + if (instr_idx == subop->ninstrs - 1 && + subop->last_instr_end_off) + end_off = subop->last_instr_end_off; + else + end_off = subop->instrs[instr_idx].ctx.data.len; + + return end_off - start_off; +} +EXPORT_SYMBOL_GPL(nand_subop_get_data_len); + /** * nand_reset - Reset and initialize a NAND device * @chip: The NAND chip @@ -4002,7 +4959,7 @@ static void nand_set_defaults(struct nand_chip *chip) chip->chip_delay = 20; /* check, if a user supplied command function given */ - if (chip->cmdfunc == NULL) + if (!chip->cmdfunc && !chip->exec_op) chip->cmdfunc = nand_command; /* check, if a user supplied wait function given */ @@ -4894,15 +5851,21 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips, if (!mtd->name && mtd->dev.parent) mtd->name = dev_name(mtd->dev.parent); - if ((!chip->cmdfunc || !chip->select_chip) && !chip->cmd_ctrl) { + /* + * ->cmdfunc() is legacy and will only be used if ->exec_op() is not + * populated. + */ + if (!chip->exec_op) { /* - * Default functions assigned for chip_select() and - * cmdfunc() both expect cmd_ctrl() to be populated, - * so we need to check that that's the case + * Default functions assigned for ->cmdfunc() and + * ->select_chip() both expect ->cmd_ctrl() to be populated. */ - pr_err("chip.cmd_ctrl() callback is not provided"); - return -EINVAL; + if ((!chip->cmdfunc || !chip->select_chip) && !chip->cmd_ctrl) { + pr_err("->cmd_ctrl() should be provided\n"); + return -EINVAL; + } } + /* Set the default functions */ nand_set_defaults(chip); diff --git a/drivers/mtd/nand/nand_hynix.c b/drivers/mtd/nand/nand_hynix.c index bae0da2aa2a8..d542908a0ebb 100644 --- a/drivers/mtd/nand/nand_hynix.c +++ b/drivers/mtd/nand/nand_hynix.c @@ -81,6 +81,15 @@ static int hynix_nand_cmd_op(struct nand_chip *chip, u8 cmd) { struct mtd_info *mtd = nand_to_mtd(chip); + if (chip->exec_op) { + struct nand_op_instr instrs[] = { + NAND_OP_CMD(cmd, 0), + }; + struct nand_operation op = NAND_OPERATION(instrs); + + return nand_exec_op(chip, &op); + } + chip->cmdfunc(mtd, cmd, -1, -1); return 0; diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h index f8f27c6801a6..469dc724f5df 100644 --- a/include/linux/mtd/rawnand.h +++ b/include/linux/mtd/rawnand.h @@ -734,6 +734,350 @@ struct nand_manufacturer_ops { void (*cleanup)(struct nand_chip *chip); }; +/** + * struct nand_op_cmd_instr - Definition of a command instruction + * @opcode: the command to issue in one cycle + */ +struct nand_op_cmd_instr { + u8 opcode; +}; + +/** + * struct nand_op_addr_instr - Definition of an address instruction + * @naddrs: length of the @addrs array + * @addrs: array containing the address cycles to issue + */ +struct nand_op_addr_instr { + unsigned int naddrs; + const u8 *addrs; +}; + +/** + * struct nand_op_data_instr - Definition of a data instruction + * @len: number of data bytes to move + * @in: buffer to fill when reading from the NAND chip + * @out: buffer to read from when writing to the NAND chip + * @force_8bit: force 8-bit access + * + * Please note that "in" and "out" are inverted from the ONFI specification + * and are from the controller perspective, so a "in" is a read from the NAND + * chip while a "out" is a write to the NAND chip. + */ +struct nand_op_data_instr { + unsigned int len; + union { + void *in; + const void *out; + } buf; + bool force_8bit; +}; + +/** + * struct nand_op_waitrdy_instr - Definition of a wait ready instruction + * @timeout_ms: maximum delay while waiting for the ready/busy pin in ms + */ +struct nand_op_waitrdy_instr { + unsigned int timeout_ms; +}; + +/** + * enum nand_op_instr_type - Definition of all instruction types + * @NAND_OP_CMD_INSTR: command instruction + * @NAND_OP_ADDR_INSTR: address instruction + * @NAND_OP_DATA_IN_INSTR: data in instruction + * @NAND_OP_DATA_OUT_INSTR: data out instruction + * @NAND_OP_WAITRDY_INSTR: wait ready instruction + */ +enum nand_op_instr_type { + NAND_OP_CMD_INSTR, + NAND_OP_ADDR_INSTR, + NAND_OP_DATA_IN_INSTR, + NAND_OP_DATA_OUT_INSTR, + NAND_OP_WAITRDY_INSTR, +}; + +/** + * struct nand_op_instr - Instruction object + * @type: the instruction type + * @cmd/@addr/@data/@waitrdy: extra data associated to the instruction. + * You'll have to use the appropriate element + * depending on @type + * @delay_ns: delay the controller should apply after the instruction has been + * issued on the bus. Most modern controllers have internal timings + * control logic, and in this case, the controller driver can ignore + * this field. + */ +struct nand_op_instr { + enum nand_op_instr_type type; + union { + struct nand_op_cmd_instr cmd; + struct nand_op_addr_instr addr; + struct nand_op_data_instr data; + struct nand_op_waitrdy_instr waitrdy; + } ctx; + unsigned int delay_ns; +}; + +/* + * Special handling must be done for the WAITRDY timeout parameter as it usually + * is either tPROG (after a prog), tR (before a read), tRST (during a reset) or + * tBERS (during an erase) which all of them are u64 values that cannot be + * divided by usual kernel macros and must be handled with the special + * DIV_ROUND_UP_ULL() macro. + */ +#define __DIVIDE(dividend, divisor) ({ \ + sizeof(dividend) == sizeof(u32) ? \ + DIV_ROUND_UP(dividend, divisor) : \ + DIV_ROUND_UP_ULL(dividend, divisor); \ + }) +#define PSEC_TO_NSEC(x) __DIVIDE(x, 1000) +#define PSEC_TO_MSEC(x) __DIVIDE(x, 1000000000) + +#define NAND_OP_CMD(id, ns) \ + { \ + .type = NAND_OP_CMD_INSTR, \ + .ctx.cmd.opcode = id, \ + .delay_ns = ns, \ + } + +#define NAND_OP_ADDR(ncycles, cycles, ns) \ + { \ + .type = NAND_OP_ADDR_INSTR, \ + .ctx.addr = { \ + .naddrs = ncycles, \ + .addrs = cycles, \ + }, \ + .delay_ns = ns, \ + } + +#define NAND_OP_DATA_IN(l, b, ns) \ + { \ + .type = NAND_OP_DATA_IN_INSTR, \ + .ctx.data = { \ + .len = l, \ + .buf.in = b, \ + .force_8bit = false, \ + }, \ + .delay_ns = ns, \ + } + +#define NAND_OP_DATA_OUT(l, b, ns) \ + { \ + .type = NAND_OP_DATA_OUT_INSTR, \ + .ctx.data = { \ + .len = l, \ + .buf.out = b, \ + .force_8bit = false, \ + }, \ + .delay_ns = ns, \ + } + +#define NAND_OP_8BIT_DATA_IN(l, b, ns) \ + { \ + .type = NAND_OP_DATA_IN_INSTR, \ + .ctx.data = { \ + .len = l, \ + .buf.in = b, \ + .force_8bit = true, \ + }, \ + .delay_ns = ns, \ + } + +#define NAND_OP_8BIT_DATA_OUT(l, b, ns) \ + { \ + .type = NAND_OP_DATA_OUT_INSTR, \ + .ctx.data = { \ + .len = l, \ + .buf.out = b, \ + .force_8bit = true, \ + }, \ + .delay_ns = ns, \ + } + +#define NAND_OP_WAIT_RDY(tout_ms, ns) \ + { \ + .type = NAND_OP_WAITRDY_INSTR, \ + .ctx.waitrdy.timeout_ms = tout_ms, \ + .delay_ns = ns, \ + } + +/** + * struct nand_subop - a sub operation + * @instrs: array of instructions + * @ninstrs: length of the @instrs array + * @first_instr_start_off: offset to start from for the first instruction + * of the sub-operation + * @last_instr_end_off: offset to end at (excluded) for the last instruction + * of the sub-operation + * + * Both @first_instr_start_off and @last_instr_end_off only apply to data or + * address instructions. + * + * When an operation cannot be handled as is by the NAND controller, it will + * be split by the parser into sub-operations which will be passed to the + * controller driver. + */ +struct nand_subop { + const struct nand_op_instr *instrs; + unsigned int ninstrs; + unsigned int first_instr_start_off; + unsigned int last_instr_end_off; +}; + +int nand_subop_get_addr_start_off(const struct nand_subop *subop, + unsigned int op_id); +int nand_subop_get_num_addr_cyc(const struct nand_subop *subop, + unsigned int op_id); +int nand_subop_get_data_start_off(const struct nand_subop *subop, + unsigned int op_id); +int nand_subop_get_data_len(const struct nand_subop *subop, + unsigned int op_id); + +/** + * struct nand_op_parser_addr_constraints - Constraints for address instructions + * @maxcycles: maximum number of address cycles the controller can issue in a + * single step + */ +struct nand_op_parser_addr_constraints { + unsigned int maxcycles; +}; + +/** + * struct nand_op_parser_data_constraints - Constraints for data instructions + * @maxlen: maximum data length that the controller can handle in a single step + */ +struct nand_op_parser_data_constraints { + unsigned int maxlen; +}; + +/** + * struct nand_op_parser_pattern_elem - One element of a pattern + * @type: the instructuction type + * @optional: whether this element of the pattern is optional or mandatory + * @addr/@data: address or data constraint (number of cycles or data length) + */ +struct nand_op_parser_pattern_elem { + enum nand_op_instr_type type; + bool optional; + union { + struct nand_op_parser_addr_constraints addr; + struct nand_op_parser_data_constraints data; + }; +}; + +#define NAND_OP_PARSER_PAT_CMD_ELEM(_opt) \ + { \ + .type = NAND_OP_CMD_INSTR, \ + .optional = _opt, \ + } + +#define NAND_OP_PARSER_PAT_ADDR_ELEM(_opt, _maxcycles) \ + { \ + .type = NAND_OP_ADDR_INSTR, \ + .optional = _opt, \ + .addr.maxcycles = _maxcycles, \ + } + +#define NAND_OP_PARSER_PAT_DATA_IN_ELEM(_opt, _maxlen) \ + { \ + .type = NAND_OP_DATA_IN_INSTR, \ + .optional = _opt, \ + .data.maxlen = _maxlen, \ + } + +#define NAND_OP_PARSER_PAT_DATA_OUT_ELEM(_opt, _maxlen) \ + { \ + .type = NAND_OP_DATA_OUT_INSTR, \ + .optional = _opt, \ + .data.maxlen = _maxlen, \ + } + +#define NAND_OP_PARSER_PAT_WAITRDY_ELEM(_opt) \ + { \ + .type = NAND_OP_WAITRDY_INSTR, \ + .optional = _opt, \ + } + +/** + * struct nand_op_parser_pattern - NAND sub-operation pattern descriptor + * @elems: array of pattern elements + * @nelems: number of pattern elements in @elems array + * @exec: the function that will issue a sub-operation + * + * A pattern is a list of elements, each element reprensenting one instruction + * with its constraints. The pattern itself is used by the core to match NAND + * chip operation with NAND controller operations. + * Once a match between a NAND controller operation pattern and a NAND chip + * operation (or a sub-set of a NAND operation) is found, the pattern ->exec() + * hook is called so that the controller driver can issue the operation on the + * bus. + * + * Controller drivers should declare as many patterns as they support and pass + * this list of patterns (created with the help of the following macro) to + * the nand_op_parser_exec_op() helper. + */ +struct nand_op_parser_pattern { + const struct nand_op_parser_pattern_elem *elems; + unsigned int nelems; + int (*exec)(struct nand_chip *chip, const struct nand_subop *subop); +}; + +#define NAND_OP_PARSER_PATTERN(_exec, ...) \ + { \ + .exec = _exec, \ + .elems = (struct nand_op_parser_pattern_elem[]) { __VA_ARGS__ }, \ + .nelems = sizeof((struct nand_op_parser_pattern_elem[]) { __VA_ARGS__ }) / \ + sizeof(struct nand_op_parser_pattern_elem), \ + } + +/** + * struct nand_op_parser - NAND controller operation parser descriptor + * @patterns: array of supported patterns + * @npatterns: length of the @patterns array + * + * The parser descriptor is just an array of supported patterns which will be + * iterated by nand_op_parser_exec_op() everytime it tries to execute an + * NAND operation (or tries to determine if a specific operation is supported). + * + * It is worth mentioning that patterns will be tested in their declaration + * order, and the first match will be taken, so it's important to order patterns + * appropriately so that simple/inefficient patterns are placed at the end of + * the list. Usually, this is where you put single instruction patterns. + */ +struct nand_op_parser { + const struct nand_op_parser_pattern *patterns; + unsigned int npatterns; +}; + +#define NAND_OP_PARSER(...) \ + { \ + .patterns = (struct nand_op_parser_pattern[]) { __VA_ARGS__ }, \ + .npatterns = sizeof((struct nand_op_parser_pattern[]) { __VA_ARGS__ }) / \ + sizeof(struct nand_op_parser_pattern), \ + } + +/** + * struct nand_operation - NAND operation descriptor + * @instrs: array of instructions to execute + * @ninstrs: length of the @instrs array + * + * The actual operation structure that will be passed to chip->exec_op(). + */ +struct nand_operation { + const struct nand_op_instr *instrs; + unsigned int ninstrs; +}; + +#define NAND_OPERATION(_instrs) \ + { \ + .instrs = _instrs, \ + .ninstrs = ARRAY_SIZE(_instrs), \ + } + +int nand_op_parser_exec_op(struct nand_chip *chip, + const struct nand_op_parser *parser, + const struct nand_operation *op, bool check_only); + /** * struct nand_chip - NAND Private Flash Chip Data * @mtd: MTD device registered to the MTD framework @@ -760,6 +1104,10 @@ struct nand_manufacturer_ops { * commands to the chip. * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on * ready. + * @exec_op: controller specific method to execute NAND operations. + * This method replaces ->cmdfunc(), + * ->{read,write}_{buf,byte,word}(), ->dev_ready() and + * ->waifunc(). * @setup_read_retry: [FLASHSPECIFIC] flash (vendor) specific function for * setting the read-retry mode. Mostly needed for MLC NAND. * @ecc: [BOARDSPECIFIC] ECC control structure @@ -859,6 +1207,9 @@ struct nand_chip { void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, int page_addr); int(*waitfunc)(struct mtd_info *mtd, struct nand_chip *this); + int (*exec_op)(struct nand_chip *chip, + const struct nand_operation *op, + bool check_only); int (*erase)(struct mtd_info *mtd, int page); int (*scan_bbt)(struct mtd_info *mtd); int (*onfi_set_features)(struct mtd_info *mtd, struct nand_chip *chip, @@ -869,7 +1220,6 @@ struct nand_chip { int (*setup_data_interface)(struct mtd_info *mtd, int chipnr, const struct nand_data_interface *conf); - int chip_delay; unsigned int options; unsigned int bbt_options; @@ -929,6 +1279,15 @@ struct nand_chip { } manufacturer; }; +static inline int nand_exec_op(struct nand_chip *chip, + const struct nand_operation *op) +{ + if (!chip->exec_op) + return -ENOTSUPP; + + return chip->exec_op(chip, op, false); +} + extern const struct mtd_ooblayout_ops nand_ooblayout_sp_ops; extern const struct mtd_ooblayout_ops nand_ooblayout_lp_ops; @@ -1320,4 +1679,11 @@ void nand_cleanup(struct nand_chip *chip); /* Default extended ID decoding function */ void nand_decode_ext_id(struct nand_chip *chip); + +/* + * External helper for controller drivers that have to implement the WAITRDY + * instruction and have no physical pin to check it. + */ +int nand_soft_waitrdy(struct nand_chip *chip, unsigned long timeout_ms); + #endif /* __LINUX_MTD_RAWNAND_H */ -- cgit v1.2.3 From 8b5c51a45c39c6d4f05c6f87d05f54b6c28f7c36 Mon Sep 17 00:00:00 2001 From: Christophe JAILLET Date: Thu, 14 Dec 2017 07:03:49 +0100 Subject: mtd: onenand: samsung: use devm_ function to simplify code and fix some leaks Convert all error handling code in 's3c_onenand_probe()' to resource-managed alternatives in order to simplify code. This fixes a resource leak if 'platform_get_resource()' fails at line 872. The 'request_irq()' at line 971 was also un-balanced. It is now resource-managed. Signed-off-by: Christophe JAILLET Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/samsung.c | 165 ++++++++---------------------------------- 1 file changed, 30 insertions(+), 135 deletions(-) diff --git a/drivers/mtd/onenand/samsung.c b/drivers/mtd/onenand/samsung.c index af0ac1a7bf8f..bad59f5cc56d 100644 --- a/drivers/mtd/onenand/samsung.c +++ b/drivers/mtd/onenand/samsung.c @@ -129,16 +129,13 @@ struct s3c_onenand { struct platform_device *pdev; enum soc_type type; void __iomem *base; - struct resource *base_res; void __iomem *ahb_addr; - struct resource *ahb_res; int bootram_command; void __iomem *page_buf; void __iomem *oob_buf; unsigned int (*mem_addr)(int fba, int fpa, int fsa); unsigned int (*cmd_map)(unsigned int type, unsigned int val); void __iomem *dma_addr; - struct resource *dma_res; unsigned long phys_base; struct completion complete; }; @@ -851,15 +848,14 @@ static int s3c_onenand_probe(struct platform_device *pdev) /* No need to check pdata. the platform data is optional */ size = sizeof(struct mtd_info) + sizeof(struct onenand_chip); - mtd = kzalloc(size, GFP_KERNEL); + mtd = devm_kzalloc(&pdev->dev, size, GFP_KERNEL); if (!mtd) return -ENOMEM; - onenand = kzalloc(sizeof(struct s3c_onenand), GFP_KERNEL); - if (!onenand) { - err = -ENOMEM; - goto onenand_fail; - } + onenand = devm_kzalloc(&pdev->dev, sizeof(struct s3c_onenand), + GFP_KERNEL); + if (!onenand) + return -ENOMEM; this = (struct onenand_chip *) &mtd[1]; mtd->priv = this; @@ -870,26 +866,12 @@ static int s3c_onenand_probe(struct platform_device *pdev) s3c_onenand_setup(mtd); r = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!r) { - dev_err(&pdev->dev, "no memory resource defined\n"); - return -ENOENT; - goto ahb_resource_failed; - } + onenand->base = devm_ioremap_resource(&pdev->dev, r); + if (IS_ERR(onenand->base)) + return PTR_ERR(onenand->base); - onenand->base_res = request_mem_region(r->start, resource_size(r), - pdev->name); - if (!onenand->base_res) { - dev_err(&pdev->dev, "failed to request memory resource\n"); - err = -EBUSY; - goto resource_failed; - } + onenand->phys_base = r->start; - onenand->base = ioremap(r->start, resource_size(r)); - if (!onenand->base) { - dev_err(&pdev->dev, "failed to map memory resource\n"); - err = -EFAULT; - goto ioremap_failed; - } /* Set onenand_chip also */ this->base = onenand->base; @@ -898,40 +880,20 @@ static int s3c_onenand_probe(struct platform_device *pdev) if (onenand->type != TYPE_S5PC110) { r = platform_get_resource(pdev, IORESOURCE_MEM, 1); - if (!r) { - dev_err(&pdev->dev, "no buffer memory resource defined\n"); - err = -ENOENT; - goto ahb_resource_failed; - } - - onenand->ahb_res = request_mem_region(r->start, resource_size(r), - pdev->name); - if (!onenand->ahb_res) { - dev_err(&pdev->dev, "failed to request buffer memory resource\n"); - err = -EBUSY; - goto ahb_resource_failed; - } - - onenand->ahb_addr = ioremap(r->start, resource_size(r)); - if (!onenand->ahb_addr) { - dev_err(&pdev->dev, "failed to map buffer memory resource\n"); - err = -EINVAL; - goto ahb_ioremap_failed; - } + onenand->ahb_addr = devm_ioremap_resource(&pdev->dev, r); + if (IS_ERR(onenand->ahb_addr)) + return PTR_ERR(onenand->ahb_addr); /* Allocate 4KiB BufferRAM */ - onenand->page_buf = kzalloc(SZ_4K, GFP_KERNEL); - if (!onenand->page_buf) { - err = -ENOMEM; - goto page_buf_fail; - } + onenand->page_buf = devm_kzalloc(&pdev->dev, SZ_4K, + GFP_KERNEL); + if (!onenand->page_buf) + return -ENOMEM; /* Allocate 128 SpareRAM */ - onenand->oob_buf = kzalloc(128, GFP_KERNEL); - if (!onenand->oob_buf) { - err = -ENOMEM; - goto oob_buf_fail; - } + onenand->oob_buf = devm_kzalloc(&pdev->dev, 128, GFP_KERNEL); + if (!onenand->oob_buf) + return -ENOMEM; /* S3C doesn't handle subpage write */ mtd->subpage_sft = 0; @@ -939,28 +901,9 @@ static int s3c_onenand_probe(struct platform_device *pdev) } else { /* S5PC110 */ r = platform_get_resource(pdev, IORESOURCE_MEM, 1); - if (!r) { - dev_err(&pdev->dev, "no dma memory resource defined\n"); - err = -ENOENT; - goto dma_resource_failed; - } - - onenand->dma_res = request_mem_region(r->start, resource_size(r), - pdev->name); - if (!onenand->dma_res) { - dev_err(&pdev->dev, "failed to request dma memory resource\n"); - err = -EBUSY; - goto dma_resource_failed; - } - - onenand->dma_addr = ioremap(r->start, resource_size(r)); - if (!onenand->dma_addr) { - dev_err(&pdev->dev, "failed to map dma memory resource\n"); - err = -EINVAL; - goto dma_ioremap_failed; - } - - onenand->phys_base = onenand->base_res->start; + onenand->dma_addr = devm_ioremap_resource(&pdev->dev, r); + if (IS_ERR(onenand->dma_addr)) + return PTR_ERR(onenand->dma_addr); s5pc110_dma_ops = s5pc110_dma_poll; /* Interrupt support */ @@ -968,19 +911,19 @@ static int s3c_onenand_probe(struct platform_device *pdev) if (r) { init_completion(&onenand->complete); s5pc110_dma_ops = s5pc110_dma_irq; - err = request_irq(r->start, s5pc110_onenand_irq, - IRQF_SHARED, "onenand", &onenand); + err = devm_request_irq(&pdev->dev, r->start, + s5pc110_onenand_irq, + IRQF_SHARED, "onenand", + &onenand); if (err) { dev_err(&pdev->dev, "failed to get irq\n"); - goto scan_failed; + return err; } } } - if (onenand_scan(mtd, 1)) { - err = -EFAULT; - goto scan_failed; - } + if (onenand_scan(mtd, 1)) + return -EFAULT; if (onenand->type != TYPE_S5PC110) { /* S3C doesn't handle subpage write */ @@ -998,36 +941,6 @@ static int s3c_onenand_probe(struct platform_device *pdev) platform_set_drvdata(pdev, mtd); return 0; - -scan_failed: - if (onenand->dma_addr) - iounmap(onenand->dma_addr); -dma_ioremap_failed: - if (onenand->dma_res) - release_mem_region(onenand->dma_res->start, - resource_size(onenand->dma_res)); - kfree(onenand->oob_buf); -oob_buf_fail: - kfree(onenand->page_buf); -page_buf_fail: - if (onenand->ahb_addr) - iounmap(onenand->ahb_addr); -ahb_ioremap_failed: - if (onenand->ahb_res) - release_mem_region(onenand->ahb_res->start, - resource_size(onenand->ahb_res)); -dma_resource_failed: -ahb_resource_failed: - iounmap(onenand->base); -ioremap_failed: - if (onenand->base_res) - release_mem_region(onenand->base_res->start, - resource_size(onenand->base_res)); -resource_failed: - kfree(onenand); -onenand_fail: - kfree(mtd); - return err; } static int s3c_onenand_remove(struct platform_device *pdev) @@ -1035,25 +948,7 @@ static int s3c_onenand_remove(struct platform_device *pdev) struct mtd_info *mtd = platform_get_drvdata(pdev); onenand_release(mtd); - if (onenand->ahb_addr) - iounmap(onenand->ahb_addr); - if (onenand->ahb_res) - release_mem_region(onenand->ahb_res->start, - resource_size(onenand->ahb_res)); - if (onenand->dma_addr) - iounmap(onenand->dma_addr); - if (onenand->dma_res) - release_mem_region(onenand->dma_res->start, - resource_size(onenand->dma_res)); - - iounmap(onenand->base); - release_mem_region(onenand->base_res->start, - resource_size(onenand->base_res)); - - kfree(onenand->oob_buf); - kfree(onenand->page_buf); - kfree(onenand); - kfree(mtd); + return 0; } -- cgit v1.2.3 From ad99be47726ccb0bcbc4b0fac12c20cba78e4c0d Mon Sep 17 00:00:00 2001 From: Christophe JAILLET Date: Thu, 14 Dec 2017 07:03:50 +0100 Subject: mtd: onenand: samsung: return an error if 'mtd_device_parse_register()' fails If 'mtd_device_parse_register()' fails, we still return 0 which mean success. Return the error code instead, as done in all the other error handling paths. Signed-off-by: Christophe JAILLET Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/samsung.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/mtd/onenand/samsung.c b/drivers/mtd/onenand/samsung.c index bad59f5cc56d..c5416d6ad571 100644 --- a/drivers/mtd/onenand/samsung.c +++ b/drivers/mtd/onenand/samsung.c @@ -937,6 +937,11 @@ static int s3c_onenand_probe(struct platform_device *pdev) err = mtd_device_parse_register(mtd, NULL, NULL, pdata ? pdata->parts : NULL, pdata ? pdata->nr_parts : 0); + if (err) { + dev_err(&pdev->dev, "failed to parse partitions and register the MTD device\n"); + onenand_release(mtd); + return err; + } platform_set_drvdata(pdev, mtd); -- cgit v1.2.3 From 0598344df0f093eba3c6e0af3caa934929c4b3aa Mon Sep 17 00:00:00 2001 From: Christophe JAILLET Date: Thu, 14 Dec 2017 07:03:51 +0100 Subject: mtd: onenand: samsung: Propagate the error returned by 'onenand_scan()' Propagate the error code returned by 'onenand_scan()' instead of a hard-coded -EFAULT. Signed-off-by: Christophe JAILLET Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/samsung.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/mtd/onenand/samsung.c b/drivers/mtd/onenand/samsung.c index c5416d6ad571..7e84a1bb91f3 100644 --- a/drivers/mtd/onenand/samsung.c +++ b/drivers/mtd/onenand/samsung.c @@ -922,8 +922,9 @@ static int s3c_onenand_probe(struct platform_device *pdev) } } - if (onenand_scan(mtd, 1)) - return -EFAULT; + err = onenand_scan(mtd, 1); + if (err) + return err; if (onenand->type != TYPE_S5PC110) { /* S3C doesn't handle subpage write */ -- cgit v1.2.3 From 24f648c2ba5d4492ce6c923c9cf3fdb3c6d821bd Mon Sep 17 00:00:00 2001 From: Christophe JAILLET Date: Thu, 14 Dec 2017 07:03:52 +0100 Subject: mtd: onenand: samsung: Remove a useless include This include is not needed, so remove it. Signed-off-by: Christophe JAILLET Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/samsung.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/mtd/onenand/samsung.c b/drivers/mtd/onenand/samsung.c index 7e84a1bb91f3..dfdfb478ba35 100644 --- a/drivers/mtd/onenand/samsung.c +++ b/drivers/mtd/onenand/samsung.c @@ -25,8 +25,6 @@ #include #include -#include - #include "samsung.h" enum soc_type { -- cgit v1.2.3 From d787b8b3509a78b1bf922cc3a1061711074847a8 Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Fri, 22 Dec 2017 18:12:41 +0100 Subject: mtd: nand: Fix unfinished comment in nand_init_data_interface() Give an unfinished comment a meaning. Signed-off-by: Miquel Raynal Signed-off-by: Boris Brezillon --- drivers/mtd/nand/nand_base.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index ab8ad9e8a8d8..96c97588e1ba 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -1284,7 +1284,10 @@ static int nand_init_data_interface(struct nand_chip *chip) if (ret) continue; - /* Pass -1 to only */ + /* + * Pass NAND_DATA_IFACE_CHECK_ONLY to only check if the + * controller supports the requested timings. + */ ret = chip->setup_data_interface(mtd, NAND_DATA_IFACE_CHECK_ONLY, &chip->data_interface); -- cgit v1.2.3 From 039b4377e5621a2cc197a7aff1e06db432e4dcc2 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Fri, 5 Jan 2018 18:02:56 -0200 Subject: mtd: nand: brcmnand: Add a NULL check for devm_kasprintf() devm_kasprintf() may fail, so we should better add a NULL check and propagate an error on failure. Signed-off-by: Fabio Estevam Signed-off-by: Boris Brezillon --- drivers/mtd/nand/brcmnand/brcmnand.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/mtd/nand/brcmnand/brcmnand.c b/drivers/mtd/nand/brcmnand/brcmnand.c index 54842512edb1..e0797abb1ebd 100644 --- a/drivers/mtd/nand/brcmnand/brcmnand.c +++ b/drivers/mtd/nand/brcmnand/brcmnand.c @@ -2237,6 +2237,9 @@ static int brcmnand_init_cs(struct brcmnand_host *host, struct device_node *dn) nand_set_controller_data(chip, host); mtd->name = devm_kasprintf(&pdev->dev, GFP_KERNEL, "brcmnand.%d", host->cs); + if (!mtd->name) + return -ENOMEM; + mtd->owner = THIS_MODULE; mtd->dev.parent = &pdev->dev; -- cgit v1.2.3 From 069f05346d01e7298939f16533953cdf52370be3 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Fri, 5 Jan 2018 18:02:55 -0200 Subject: mtd: nand: qcom: Add a NULL check for devm_kasprintf() devm_kasprintf() may fail, so we should better add a NULL check and propagate an error on failure. Signed-off-by: Fabio Estevam Signed-off-by: Boris Brezillon --- drivers/mtd/nand/qcom_nandc.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/mtd/nand/qcom_nandc.c b/drivers/mtd/nand/qcom_nandc.c index 245d0f39e0aa..6be555806eca 100644 --- a/drivers/mtd/nand/qcom_nandc.c +++ b/drivers/mtd/nand/qcom_nandc.c @@ -2639,6 +2639,9 @@ static int qcom_nand_host_init(struct qcom_nand_controller *nandc, nand_set_flash_node(chip, dn); mtd->name = devm_kasprintf(dev, GFP_KERNEL, "qcom_nand.%d", host->cs); + if (!mtd->name) + return -ENOMEM; + mtd->owner = THIS_MODULE; mtd->dev.parent = dev; -- cgit v1.2.3 From f953f0f89663c39f08f4baaa8a4a881401b65654 Mon Sep 17 00:00:00 2001 From: Kamal Dasu Date: Mon, 8 Jan 2018 15:36:48 -0500 Subject: mtd: nand: brcmnand: Disable prefetch by default Brcm nand controller prefetch feature needs to be disabled by default. Enabling affects performance on random reads as well as dma reads. Signed-off-by: Kamal Dasu Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller") Cc: Acked-by: Florian Fainelli Signed-off-by: Boris Brezillon --- drivers/mtd/nand/brcmnand/brcmnand.c | 13 +++---------- 1 file changed, 3 insertions(+), 10 deletions(-) diff --git a/drivers/mtd/nand/brcmnand/brcmnand.c b/drivers/mtd/nand/brcmnand/brcmnand.c index e0797abb1ebd..b81ddbaae149 100644 --- a/drivers/mtd/nand/brcmnand/brcmnand.c +++ b/drivers/mtd/nand/brcmnand/brcmnand.c @@ -2200,16 +2200,9 @@ static int brcmnand_setup_dev(struct brcmnand_host *host) if (ctrl->nand_version >= 0x0702) tmp |= ACC_CONTROL_RD_ERASED; tmp &= ~ACC_CONTROL_FAST_PGM_RDIN; - if (ctrl->features & BRCMNAND_HAS_PREFETCH) { - /* - * FIXME: Flash DMA + prefetch may see spurious erased-page ECC - * errors - */ - if (has_flash_dma(ctrl)) - tmp &= ~ACC_CONTROL_PREFETCH; - else - tmp |= ACC_CONTROL_PREFETCH; - } + if (ctrl->features & BRCMNAND_HAS_PREFETCH) + tmp &= ~ACC_CONTROL_PREFETCH; + nand_writereg(ctrl, offs, tmp); return 0; -- cgit v1.2.3 From 6cbefbdcec41bf725b308288dcb200a6efc3339f Mon Sep 17 00:00:00 2001 From: Sascha Hauer Date: Tue, 9 Jan 2018 10:47:02 +0100 Subject: mtd: tests: nandbiterrs: Fix read_page return value The number of corrected bitflips is not correctly reported by the test until the bitflip threshold is reached. read_page() shall return the number of corrected bitflips, but mtd_read() returns 0 or a negative error, so we can't forward its return value. In the absence of an error we always have calculate the number of bitflips ourselves. Signed-off-by: Sascha Hauer Signed-off-by: Boris Brezillon --- drivers/mtd/tests/nandbiterrs.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mtd/tests/nandbiterrs.c b/drivers/mtd/tests/nandbiterrs.c index 5f03b8c885a9..cde19c99e77b 100644 --- a/drivers/mtd/tests/nandbiterrs.c +++ b/drivers/mtd/tests/nandbiterrs.c @@ -151,7 +151,7 @@ static int read_page(int log) memcpy(&oldstats, &mtd->ecc_stats, sizeof(oldstats)); err = mtd_read(mtd, offset, mtd->writesize, &read, rbuffer); - if (err == -EUCLEAN) + if (!err || err == -EUCLEAN) err = mtd->ecc_stats.corrected - oldstats.corrected; if (err < 0 || read != mtd->writesize) { -- cgit v1.2.3 From 09ec417b0ea8bdab18e78d3d55e0a5fb7d54f18c Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Tue, 9 Jan 2018 14:19:11 +0100 Subject: mtd: nand: samsung: Disable subpage writes on E-die NAND Samsung E-die SLC NAND manufactured using 21nm process (K9F1G08U0E) does not support partial page programming, so disable subpage writes for it. Manufacturing process is stored in lowest two bits of 5th ID byte. Signed-off-by: Ladislav Michl Signed-off-by: Boris Brezillon --- drivers/mtd/nand/nand_samsung.c | 21 +++++++++++++++++---- 1 file changed, 17 insertions(+), 4 deletions(-) diff --git a/drivers/mtd/nand/nand_samsung.c b/drivers/mtd/nand/nand_samsung.c index f6b0a63a068c..ef022f62f74c 100644 --- a/drivers/mtd/nand/nand_samsung.c +++ b/drivers/mtd/nand/nand_samsung.c @@ -92,10 +92,23 @@ static void samsung_nand_decode_id(struct nand_chip *chip) } else { nand_decode_ext_id(chip); - /* Datasheet values for SLC Samsung K9F4G08U0D-S[I|C]B0(T00) */ - if (nand_is_slc(chip) && chip->id.data[1] == 0xDC) { - chip->ecc_step_ds = 512; - chip->ecc_strength_ds = 1; + if (nand_is_slc(chip)) { + switch (chip->id.data[1]) { + /* K9F4G08U0D-S[I|C]B0(T00) */ + case 0xDC: + chip->ecc_step_ds = 512; + chip->ecc_strength_ds = 1; + break; + + /* K9F1G08U0E 21nm chips do not support subpage write */ + case 0xF1: + if (chip->id.len > 4 && + (chip->id.data[4] & GENMASK(1, 0)) == 0x1) + chip->options |= NAND_NO_SUBPAGE_WRITE; + break; + default: + break; + } } } } -- cgit v1.2.3 From 7cce5d835467ea66c342951d0ed6adaffe39b1c8 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Thu, 11 Jan 2018 17:26:59 +0100 Subject: MAINTAINERS: mtd/nand: update Microchip nand entry Update Wenyou Yang email address. Take advantage of this update to move this entry to the MICROCHIP / ATMEL location and add the DT binding documentation link. Signed-off-by: Nicolas Ferre Acked-by: Wenyou Yang Signed-off-by: Boris Brezillon --- MAINTAINERS | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index aa71ab52fd76..37ee5ae4bae2 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2382,13 +2382,6 @@ F: Documentation/devicetree/bindings/input/atmel,maxtouch.txt F: drivers/input/touchscreen/atmel_mxt_ts.c F: include/linux/platform_data/atmel_mxt_ts.h -ATMEL NAND DRIVER -M: Wenyou Yang -M: Josh Wu -L: linux-mtd@lists.infradead.org -S: Supported -F: drivers/mtd/nand/atmel/* - ATMEL SAMA5D2 ADC DRIVER M: Ludovic Desroches L: linux-iio@vger.kernel.org @@ -9045,6 +9038,14 @@ F: drivers/media/platform/atmel/atmel-isc.c F: drivers/media/platform/atmel/atmel-isc-regs.h F: devicetree/bindings/media/atmel-isc.txt +MICROCHIP / ATMEL NAND DRIVER +M: Wenyou Yang +M: Josh Wu +L: linux-mtd@lists.infradead.org +S: Supported +F: drivers/mtd/nand/atmel/* +F: Documentation/devicetree/bindings/mtd/atmel-nand.txt + MICROCHIP KSZ SERIES ETHERNET SWITCH DRIVER M: Woojung Huh M: Microchip Linux Driver Support -- cgit v1.2.3 From 12663b442e5ac5aa3d6097cd3f287c71ba46d26e Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Thu, 11 Jan 2018 21:39:20 +0100 Subject: mtd: mtd_oobtest: Handle bitflips during reads Reads from NAND devices usually trigger bitflips, this is an expected behavior. While bitflips are under a given threshold, the MTD core returns 0. However, when the number of corrected bitflips is above this same threshold, -EUCLEAN is returned to inform the upper layer that this block is slightly dying and soon the ECC engine will be overtaken so actions should be taken to move the data out of it. This particular condition should not be treated like an error and the test should continue. Signed-off-by: Miquel Raynal Signed-off-by: Boris Brezillon --- drivers/mtd/tests/oobtest.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/drivers/mtd/tests/oobtest.c b/drivers/mtd/tests/oobtest.c index 1cb3f7758fb6..766b2c385682 100644 --- a/drivers/mtd/tests/oobtest.c +++ b/drivers/mtd/tests/oobtest.c @@ -193,6 +193,9 @@ static int verify_eraseblock(int ebnum) ops.datbuf = NULL; ops.oobbuf = readbuf; err = mtd_read_oob(mtd, addr, &ops); + if (mtd_is_bitflip(err)) + err = 0; + if (err || ops.oobretlen != use_len) { pr_err("error: readoob failed at %#llx\n", (long long)addr); @@ -227,6 +230,9 @@ static int verify_eraseblock(int ebnum) ops.datbuf = NULL; ops.oobbuf = readbuf; err = mtd_read_oob(mtd, addr, &ops); + if (mtd_is_bitflip(err)) + err = 0; + if (err || ops.oobretlen != mtd->oobavail) { pr_err("error: readoob failed at %#llx\n", (long long)addr); @@ -286,6 +292,9 @@ static int verify_eraseblock_in_one_go(int ebnum) /* read entire block's OOB at one go */ err = mtd_read_oob(mtd, addr, &ops); + if (mtd_is_bitflip(err)) + err = 0; + if (err || ops.oobretlen != len) { pr_err("error: readoob failed at %#llx\n", (long long)addr); @@ -527,6 +536,9 @@ static int __init mtd_oobtest_init(void) pr_info("attempting to start read past end of OOB\n"); pr_info("an error is expected...\n"); err = mtd_read_oob(mtd, addr0, &ops); + if (mtd_is_bitflip(err)) + err = 0; + if (err) { pr_info("error occurred as expected\n"); err = 0; @@ -571,6 +583,9 @@ static int __init mtd_oobtest_init(void) pr_info("attempting to read past end of device\n"); pr_info("an error is expected...\n"); err = mtd_read_oob(mtd, mtd->size - mtd->writesize, &ops); + if (mtd_is_bitflip(err)) + err = 0; + if (err) { pr_info("error occurred as expected\n"); err = 0; @@ -615,6 +630,9 @@ static int __init mtd_oobtest_init(void) pr_info("attempting to read past end of device\n"); pr_info("an error is expected...\n"); err = mtd_read_oob(mtd, mtd->size - mtd->writesize, &ops); + if (mtd_is_bitflip(err)) + err = 0; + if (err) { pr_info("error occurred as expected\n"); err = 0; @@ -684,6 +702,9 @@ static int __init mtd_oobtest_init(void) ops.datbuf = NULL; ops.oobbuf = readbuf; err = mtd_read_oob(mtd, addr, &ops); + if (mtd_is_bitflip(err)) + err = 0; + if (err) goto out; if (memcmpshow(addr, readbuf, writebuf, -- cgit v1.2.3 From 87e89ce8d0d14f573c068c61bec2117751fb5103 Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Fri, 12 Jan 2018 10:13:36 +0100 Subject: mtd: nand: Fix nand_do_read_oob() return value Starting from commit 041e4575f034 ("mtd: nand: handle ECC errors in OOB"), nand_do_read_oob() (from the NAND core) did return 0 or a negative error, and the MTD layer expected it. However, the trend for the NAND layer is now to return an error or a positive number of bitflips. Deciding which status to return to the user belongs to the MTD layer. Commit e47f68587b82 ("mtd: check for max_bitflips in mtd_read_oob()") brought this logic to the mtd_read_oob() function while the return value coming from nand_do_read_oob() (called by the ->_read_oob() hook) was left unchanged. Fixes: e47f68587b82 ("mtd: check for max_bitflips in mtd_read_oob()") Cc: stable@vger.kernel.org Signed-off-by: Miquel Raynal Signed-off-by: Boris Brezillon --- drivers/mtd/nand/nand_base.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 96c97588e1ba..3ff77bef9739 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -3797,6 +3797,7 @@ EXPORT_SYMBOL(nand_write_oob_syndrome); static int nand_do_read_oob(struct mtd_info *mtd, loff_t from, struct mtd_oob_ops *ops) { + unsigned int max_bitflips = 0; int page, realpage, chipnr; struct nand_chip *chip = mtd_to_nand(mtd); struct mtd_ecc_stats stats; @@ -3854,6 +3855,8 @@ static int nand_do_read_oob(struct mtd_info *mtd, loff_t from, nand_wait_ready(mtd); } + max_bitflips = max_t(unsigned int, max_bitflips, ret); + readlen -= len; if (!readlen) break; @@ -3879,7 +3882,7 @@ static int nand_do_read_oob(struct mtd_info *mtd, loff_t from, if (mtd->ecc_stats.failed - stats.failed) return -EBADMSG; - return mtd->ecc_stats.corrected - stats.corrected ? -EUCLEAN : 0; + return max_bitflips; } /** -- cgit v1.2.3 From b76bb4e64e7514a9d9027e2b0d0b76ee84a4d27b Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Tue, 9 Jan 2018 11:36:31 +0100 Subject: dt-bindings: mtd: document new nand-rb property There are already an atmel,rb and an allwinner,rb properties, let's not make other ones and instead use a generic term: nand-rb to define NAND chips Ready/Busy lines. Signed-off-by: Miquel Raynal Reviewed-by: Rob Herring Signed-off-by: Boris Brezillon --- Documentation/devicetree/bindings/mtd/nand.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt index 133f3813719c..8bb11d809429 100644 --- a/Documentation/devicetree/bindings/mtd/nand.txt +++ b/Documentation/devicetree/bindings/mtd/nand.txt @@ -43,6 +43,7 @@ Optional NAND chip properties: This is particularly useful when only the in-band area is used by the upper layers, and you want to make your NAND as reliable as possible. +- nand-rb: shall contain the native Ready/Busy ids. The ECC strength and ECC step size properties define the correction capability of a controller. Together, they say a controller can correct "{strength} bit -- cgit v1.2.3 From a82d20698a92cab7c885355cd0ba3c76c45c9e2f Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Tue, 9 Jan 2018 11:36:32 +0100 Subject: dt-bindings: mtd: add Marvell NAND controller documentation Document the legacy and the new bindings for Marvell NAND controller. The pxa3xx_nand.c driver does only support legacy bindings, which are incomplete and inaccurate. A rework of this controller (called marvell_nand.c) does support both. Signed-off-by: Miquel Raynal Reviewed-by: Rob Herring Signed-off-by: Boris Brezillon --- .../devicetree/bindings/mtd/marvell-nand.txt | 123 +++++++++++++++++++++ 1 file changed, 123 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/marvell-nand.txt diff --git a/Documentation/devicetree/bindings/mtd/marvell-nand.txt b/Documentation/devicetree/bindings/mtd/marvell-nand.txt new file mode 100644 index 000000000000..c08fb477b3c6 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/marvell-nand.txt @@ -0,0 +1,123 @@ +Marvell NAND Flash Controller (NFC) + +Required properties: +- compatible: can be one of the following: + * "marvell,armada-8k-nand-controller" + * "marvell,armada370-nand-controller" + * "marvell,pxa3xx-nand-controller" + * "marvell,armada-8k-nand" (deprecated) + * "marvell,armada370-nand" (deprecated) + * "marvell,pxa3xx-nand" (deprecated) + Compatibles marked deprecated support only the old bindings described + at the bottom. +- reg: NAND flash controller memory area. +- #address-cells: shall be set to 1. Encode the NAND CS. +- #size-cells: shall be set to 0. +- interrupts: shall define the NAND controller interrupt. +- clocks: shall reference the NAND controller clock. +- marvell,system-controller: Set to retrieve the syscon node that handles + NAND controller related registers (only required with the + "marvell,armada-8k-nand[-controller]" compatibles). + +Optional properties: +- label: see partition.txt. New platforms shall omit this property. +- dmas: shall reference DMA channel associated to the NAND controller. + This property is only used with "marvell,pxa3xx-nand[-controller]" + compatible strings. +- dma-names: shall be "rxtx". + This property is only used with "marvell,pxa3xx-nand[-controller]" + compatible strings. + +Optional children nodes: +Children nodes represent the available NAND chips. + +Required properties: +- reg: shall contain the native Chip Select ids (0-3). +- nand-rb: see nand.txt (0-1). + +Optional properties: +- marvell,nand-keep-config: orders the driver not to take the timings + from the core and leaving them completely untouched. Bootloader + timings will then be used. +- label: MTD name. +- nand-on-flash-bbt: see nand.txt. +- nand-ecc-mode: see nand.txt. Will use hardware ECC if not specified. +- nand-ecc-algo: see nand.txt. This property is essentially useful when + not using hardware ECC. Howerver, it may be added when using hardware + ECC for clarification but will be ignored by the driver because ECC + mode is chosen depending on the page size and the strength required by + the NAND chip. This value may be overwritten with nand-ecc-strength + property. +- nand-ecc-strength: see nand.txt. +- nand-ecc-step-size: see nand.txt. Marvell's NAND flash controller does + use fixed strength (1-bit for Hamming, 16-bit for BCH), so the actual + step size will shrink or grow in order to fit the required strength. + Step sizes are not completely random for all and follow certain + patterns described in AN-379, "Marvell SoC NFC ECC". + +See Documentation/devicetree/bindings/mtd/nand.txt for more details on +generic bindings. + + +Example: +nand_controller: nand-controller@d0000 { + compatible = "marvell,armada370-nand-controller"; + reg = <0xd0000 0x54>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = ; + clocks = <&coredivclk 0>; + + nand@0 { + reg = <0>; + label = "main-storage"; + nand-rb = <0>; + nand-ecc-mode = "hw"; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Rootfs"; + reg = <0x00000000 0x40000000>; + }; + }; + }; +}; + + +Note on legacy bindings: One can find, in not-updated device trees, +bindings slightly different than described above with other properties +described below as well as the partitions node at the root of a so +called "nand" node (without clear controller/chip separation). + +Legacy properties: +- marvell,nand-enable-arbiter: To enable the arbiter, all boards blindly + used it, this bit was set by the bootloader for many boards and even if + it is marked reserved in several datasheets, it might be needed to set + it (otherwise it is harmless) so whether or not this property is set, + the bit is selected by the driver. +- num-cs: Number of chip-select lines to use, all boards blindly set 1 + to this and for a reason, other values would have failed. The value of + this property is ignored. + +Example: + + nand0: nand@43100000 { + compatible = "marvell,pxa3xx-nand"; + reg = <0x43100000 90>; + interrupts = <45>; + dmas = <&pdma 97 0>; + dma-names = "rxtx"; + #address-cells = <1>; + marvell,nand-keep-config; + marvell,nand-enable-arbiter; + num-cs = <1>; + /* Partitions (optional) */ + }; -- cgit v1.2.3 From 02f26ecf8c772751d4b24744d487f6b1b20e75d4 Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Tue, 9 Jan 2018 11:36:33 +0100 Subject: mtd: nand: add reworked Marvell NAND controller driver Add marvell_nand driver which aims at replacing the existing pxa3xx_nand driver. The new driver intends to be easier to understand and follows the brand new NAND framework rules by implementing hooks for every pattern the controller might support and referencing them inside a parser object that will be given to the core at each ->exec_op() call. Raw accessors are implemented, useful to test/debug memory/filesystem corruptions. Userspace binaries contained in the mtd-utils package may now be used and their output trusted. Most of the DT nodes using the old driver kept non-optimal timings from the bootloader (even if there was some mechanisms to derive them if the chip was ONFI compliant). The new default is to implement ->setup_data_interface() and follow the core's decision regarding the chip. Thanks to the improved timings, implementation of ONFI mode 5 support (with EDO managed by adding a delay on data sampling), merging the commands together and optimizing writes in the command registers, the new driver may achieve faster throughputs in both directions. Measurements show an improvement of about +23% read throughput and +24% write throughput. These measurements have been done with an Armada-385-DB-AP (4kiB NAND pages forced in 4-bit strength BCH ECC correction) using the userspace tool 'flash_speed' from the MTD test suite. Besides these important topics, the new driver addresses several unsolved known issues in the old driver which: - did not work with ECC soft neither with ECC none ; - relied on naked read/write (which is unchanged) while the NFCv1 embedded in the pxa3xx platforms do not implement it, so several NAND commands did not actually ever work without any notice (like reading the ONFI PARAM_PAGE or SET/GET_FEATURES) ; - wrote the OOB data correctly, but was not able to read it correctly past the first OOB data chunk ; - did not retrieve ECC bytes ; - used device tree bindings that did not allow more than one NAND chip, and did not allow to choose the correct chip select if not incrementing from 0. Plus, the Ready/Busy line used had to be 0. Old device tree bindings are still supported but deprecated. A more hierarchical view has to be used to keep the controller and the NAND chip structures clearly separated both inside the device tree and also in the driver code. Signed-off-by: Miquel Raynal Tested-by: Sean Nyekjaer Tested-by: Willy Tarreau Signed-off-by: Boris Brezillon --- drivers/mtd/nand/Kconfig | 13 + drivers/mtd/nand/Makefile | 1 + drivers/mtd/nand/marvell_nand.c | 2898 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 2912 insertions(+) create mode 100644 drivers/mtd/nand/marvell_nand.c diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 859eb7790c46..e6b8c59f2c0d 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -315,6 +315,7 @@ config MTD_NAND_ATMEL config MTD_NAND_PXA3xx tristate "NAND support on PXA3xx and Armada 370/XP" + depends on !MTD_NAND_MARVELL depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU help @@ -323,6 +324,18 @@ config MTD_NAND_PXA3xx platforms (XP, 370, 375, 38x, 39x) and 64-bit Armada platforms (7K, 8K) (NFCv2). +config MTD_NAND_MARVELL + tristate "NAND controller support on Marvell boards" + depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU || \ + COMPILE_TEST + depends on HAS_IOMEM + help + This enables the NAND flash controller driver for Marvell boards, + including: + - PXA3xx processors (NFCv1) + - 32-bit Armada platforms (XP, 37x, 38x, 39x) (NFCv2) + - 64-bit Aramda platforms (7k, 8k) (NFCv2) + config MTD_NAND_SLC_LPC32XX tristate "NXP LPC32xx SLC Controller" depends on ARCH_LPC32XX diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile index 118a1349aad3..921634ba400c 100644 --- a/drivers/mtd/nand/Makefile +++ b/drivers/mtd/nand/Makefile @@ -32,6 +32,7 @@ obj-$(CONFIG_MTD_NAND_OMAP2) += omap2_nand.o obj-$(CONFIG_MTD_NAND_OMAP_BCH_BUILD) += omap_elm.o obj-$(CONFIG_MTD_NAND_CM_X270) += cmx270_nand.o obj-$(CONFIG_MTD_NAND_PXA3xx) += pxa3xx_nand.o +obj-$(CONFIG_MTD_NAND_MARVELL) += marvell_nand.o obj-$(CONFIG_MTD_NAND_TMIO) += tmio_nand.o obj-$(CONFIG_MTD_NAND_PLATFORM) += plat_nand.o obj-$(CONFIG_MTD_NAND_PASEMI) += pasemi_nand.o diff --git a/drivers/mtd/nand/marvell_nand.c b/drivers/mtd/nand/marvell_nand.c new file mode 100644 index 000000000000..b8fec6093b75 --- /dev/null +++ b/drivers/mtd/nand/marvell_nand.c @@ -0,0 +1,2898 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Marvell NAND flash controller driver + * + * Copyright (C) 2017 Marvell + * Author: Miquel RAYNAL + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +/* Data FIFO granularity, FIFO reads/writes must be a multiple of this length */ +#define FIFO_DEPTH 8 +#define FIFO_REP(x) (x / sizeof(u32)) +#define BCH_SEQ_READS (32 / FIFO_DEPTH) +/* NFC does not support transfers of larger chunks at a time */ +#define MAX_CHUNK_SIZE 2112 +/* NFCv1 cannot read more that 7 bytes of ID */ +#define NFCV1_READID_LEN 7 +/* Polling is done at a pace of POLL_PERIOD us until POLL_TIMEOUT is reached */ +#define POLL_PERIOD 0 +#define POLL_TIMEOUT 100000 +/* Interrupt maximum wait period in ms */ +#define IRQ_TIMEOUT 1000 +/* Latency in clock cycles between SoC pins and NFC logic */ +#define MIN_RD_DEL_CNT 3 +/* Maximum number of contiguous address cycles */ +#define MAX_ADDRESS_CYC_NFCV1 5 +#define MAX_ADDRESS_CYC_NFCV2 7 +/* System control registers/bits to enable the NAND controller on some SoCs */ +#define GENCONF_SOC_DEVICE_MUX 0x208 +#define GENCONF_SOC_DEVICE_MUX_NFC_EN BIT(0) +#define GENCONF_SOC_DEVICE_MUX_ECC_CLK_RST BIT(20) +#define GENCONF_SOC_DEVICE_MUX_ECC_CORE_RST BIT(21) +#define GENCONF_SOC_DEVICE_MUX_NFC_INT_EN BIT(25) +#define GENCONF_CLK_GATING_CTRL 0x220 +#define GENCONF_CLK_GATING_CTRL_ND_GATE BIT(2) +#define GENCONF_ND_CLK_CTRL 0x700 +#define GENCONF_ND_CLK_CTRL_EN BIT(0) + +/* NAND controller data flash control register */ +#define NDCR 0x00 +#define NDCR_ALL_INT GENMASK(11, 0) +#define NDCR_CS1_CMDDM BIT(7) +#define NDCR_CS0_CMDDM BIT(8) +#define NDCR_RDYM BIT(11) +#define NDCR_ND_ARB_EN BIT(12) +#define NDCR_RA_START BIT(15) +#define NDCR_RD_ID_CNT(x) (min_t(unsigned int, x, 0x7) << 16) +#define NDCR_PAGE_SZ(x) (x >= 2048 ? BIT(24) : 0) +#define NDCR_DWIDTH_M BIT(26) +#define NDCR_DWIDTH_C BIT(27) +#define NDCR_ND_RUN BIT(28) +#define NDCR_DMA_EN BIT(29) +#define NDCR_ECC_EN BIT(30) +#define NDCR_SPARE_EN BIT(31) +#define NDCR_GENERIC_FIELDS_MASK (~(NDCR_RA_START | NDCR_PAGE_SZ(2048) | \ + NDCR_DWIDTH_M | NDCR_DWIDTH_C)) + +/* NAND interface timing parameter 0 register */ +#define NDTR0 0x04 +#define NDTR0_TRP(x) ((min_t(unsigned int, x, 0xF) & 0x7) << 0) +#define NDTR0_TRH(x) (min_t(unsigned int, x, 0x7) << 3) +#define NDTR0_ETRP(x) ((min_t(unsigned int, x, 0xF) & 0x8) << 3) +#define NDTR0_SEL_NRE_EDGE BIT(7) +#define NDTR0_TWP(x) (min_t(unsigned int, x, 0x7) << 8) +#define NDTR0_TWH(x) (min_t(unsigned int, x, 0x7) << 11) +#define NDTR0_TCS(x) (min_t(unsigned int, x, 0x7) << 16) +#define NDTR0_TCH(x) (min_t(unsigned int, x, 0x7) << 19) +#define NDTR0_RD_CNT_DEL(x) (min_t(unsigned int, x, 0xF) << 22) +#define NDTR0_SELCNTR BIT(26) +#define NDTR0_TADL(x) (min_t(unsigned int, x, 0x1F) << 27) + +/* NAND interface timing parameter 1 register */ +#define NDTR1 0x0C +#define NDTR1_TAR(x) (min_t(unsigned int, x, 0xF) << 0) +#define NDTR1_TWHR(x) (min_t(unsigned int, x, 0xF) << 4) +#define NDTR1_TRHW(x) (min_t(unsigned int, x / 16, 0x3) << 8) +#define NDTR1_PRESCALE BIT(14) +#define NDTR1_WAIT_MODE BIT(15) +#define NDTR1_TR(x) (min_t(unsigned int, x, 0xFFFF) << 16) + +/* NAND controller status register */ +#define NDSR 0x14 +#define NDSR_WRCMDREQ BIT(0) +#define NDSR_RDDREQ BIT(1) +#define NDSR_WRDREQ BIT(2) +#define NDSR_CORERR BIT(3) +#define NDSR_UNCERR BIT(4) +#define NDSR_CMDD(cs) BIT(8 - cs) +#define NDSR_RDY(rb) BIT(11 + rb) +#define NDSR_ERRCNT(x) ((x >> 16) & 0x1F) + +/* NAND ECC control register */ +#define NDECCCTRL 0x28 +#define NDECCCTRL_BCH_EN BIT(0) + +/* NAND controller data buffer register */ +#define NDDB 0x40 + +/* NAND controller command buffer 0 register */ +#define NDCB0 0x48 +#define NDCB0_CMD1(x) ((x & 0xFF) << 0) +#define NDCB0_CMD2(x) ((x & 0xFF) << 8) +#define NDCB0_ADDR_CYC(x) ((x & 0x7) << 16) +#define NDCB0_ADDR_GET_NUM_CYC(x) (((x) >> 16) & 0x7) +#define NDCB0_DBC BIT(19) +#define NDCB0_CMD_TYPE(x) ((x & 0x7) << 21) +#define NDCB0_CSEL BIT(24) +#define NDCB0_RDY_BYP BIT(27) +#define NDCB0_LEN_OVRD BIT(28) +#define NDCB0_CMD_XTYPE(x) ((x & 0x7) << 29) + +/* NAND controller command buffer 1 register */ +#define NDCB1 0x4C +#define NDCB1_COLS(x) ((x & 0xFFFF) << 0) +#define NDCB1_ADDRS_PAGE(x) (x << 16) + +/* NAND controller command buffer 2 register */ +#define NDCB2 0x50 +#define NDCB2_ADDR5_PAGE(x) (((x >> 16) & 0xFF) << 0) +#define NDCB2_ADDR5_CYC(x) ((x & 0xFF) << 0) + +/* NAND controller command buffer 3 register */ +#define NDCB3 0x54 +#define NDCB3_ADDR6_CYC(x) ((x & 0xFF) << 16) +#define NDCB3_ADDR7_CYC(x) ((x & 0xFF) << 24) + +/* NAND controller command buffer 0 register 'type' and 'xtype' fields */ +#define TYPE_READ 0 +#define TYPE_WRITE 1 +#define TYPE_ERASE 2 +#define TYPE_READ_ID 3 +#define TYPE_STATUS 4 +#define TYPE_RESET 5 +#define TYPE_NAKED_CMD 6 +#define TYPE_NAKED_ADDR 7 +#define TYPE_MASK 7 +#define XTYPE_MONOLITHIC_RW 0 +#define XTYPE_LAST_NAKED_RW 1 +#define XTYPE_FINAL_COMMAND 3 +#define XTYPE_READ 4 +#define XTYPE_WRITE_DISPATCH 4 +#define XTYPE_NAKED_RW 5 +#define XTYPE_COMMAND_DISPATCH 6 +#define XTYPE_MASK 7 + +/** + * Marvell ECC engine works differently than the others, in order to limit the + * size of the IP, hardware engineers chose to set a fixed strength at 16 bits + * per subpage, and depending on a the desired strength needed by the NAND chip, + * a particular layout mixing data/spare/ecc is defined, with a possible last + * chunk smaller that the others. + * + * @writesize: Full page size on which the layout applies + * @chunk: Desired ECC chunk size on which the layout applies + * @strength: Desired ECC strength (per chunk size bytes) on which the + * layout applies + * @nchunks: Total number of chunks + * @full_chunk_cnt: Number of full-sized chunks, which is the number of + * repetitions of the pattern: + * (data_bytes + spare_bytes + ecc_bytes). + * @data_bytes: Number of data bytes per chunk + * @spare_bytes: Number of spare bytes per chunk + * @ecc_bytes: Number of ecc bytes per chunk + * @last_data_bytes: Number of data bytes in the last chunk + * @last_spare_bytes: Number of spare bytes in the last chunk + * @last_ecc_bytes: Number of ecc bytes in the last chunk + */ +struct marvell_hw_ecc_layout { + /* Constraints */ + int writesize; + int chunk; + int strength; + /* Corresponding layout */ + int nchunks; + int full_chunk_cnt; + int data_bytes; + int spare_bytes; + int ecc_bytes; + int last_data_bytes; + int last_spare_bytes; + int last_ecc_bytes; +}; + +#define MARVELL_LAYOUT(ws, dc, ds, nc, fcc, db, sb, eb, ldb, lsb, leb) \ + { \ + .writesize = ws, \ + .chunk = dc, \ + .strength = ds, \ + .nchunks = nc, \ + .full_chunk_cnt = fcc, \ + .data_bytes = db, \ + .spare_bytes = sb, \ + .ecc_bytes = eb, \ + .last_data_bytes = ldb, \ + .last_spare_bytes = lsb, \ + .last_ecc_bytes = leb, \ + } + +/* Layouts explained in AN-379_Marvell_SoC_NFC_ECC */ +static const struct marvell_hw_ecc_layout marvell_nfc_layouts[] = { + MARVELL_LAYOUT( 512, 512, 1, 1, 1, 512, 8, 8, 0, 0, 0), + MARVELL_LAYOUT( 2048, 512, 1, 1, 1, 2048, 40, 24, 0, 0, 0), + MARVELL_LAYOUT( 2048, 512, 4, 1, 1, 2048, 32, 30, 0, 0, 0), + MARVELL_LAYOUT( 4096, 512, 4, 2, 2, 2048, 32, 30, 0, 0, 0), + MARVELL_LAYOUT( 4096, 512, 8, 5, 4, 1024, 0, 30, 0, 64, 30), +}; + +/** + * The Nand Flash Controller has up to 4 CE and 2 RB pins. The CE selection + * is made by a field in NDCB0 register, and in another field in NDCB2 register. + * The datasheet describes the logic with an error: ADDR5 field is once + * declared at the beginning of NDCB2, and another time at its end. Because the + * ADDR5 field of NDCB2 may be used by other bytes, it would be more logical + * to use the last bit of this field instead of the first ones. + * + * @cs: Wanted CE lane. + * @ndcb0_csel: Value of the NDCB0 register with or without the flag + * selecting the wanted CE lane. This is set once when + * the Device Tree is probed. + * @rb: Ready/Busy pin for the flash chip + */ +struct marvell_nand_chip_sel { + unsigned int cs; + u32 ndcb0_csel; + unsigned int rb; +}; + +/** + * NAND chip structure: stores NAND chip device related information + * + * @chip: Base NAND chip structure + * @node: Used to store NAND chips into a list + * @layout NAND layout when using hardware ECC + * @ndcr: Controller register value for this NAND chip + * @ndtr0: Timing registers 0 value for this NAND chip + * @ndtr1: Timing registers 1 value for this NAND chip + * @selected_die: Current active CS + * @nsels: Number of CS lines required by the NAND chip + * @sels: Array of CS lines descriptions + */ +struct marvell_nand_chip { + struct nand_chip chip; + struct list_head node; + const struct marvell_hw_ecc_layout *layout; + u32 ndcr; + u32 ndtr0; + u32 ndtr1; + int addr_cyc; + int selected_die; + unsigned int nsels; + struct marvell_nand_chip_sel sels[0]; +}; + +static inline struct marvell_nand_chip *to_marvell_nand(struct nand_chip *chip) +{ + return container_of(chip, struct marvell_nand_chip, chip); +} + +static inline struct marvell_nand_chip_sel *to_nand_sel(struct marvell_nand_chip + *nand) +{ + return &nand->sels[nand->selected_die]; +} + +/** + * NAND controller capabilities for distinction between compatible strings + * + * @max_cs_nb: Number of Chip Select lines available + * @max_rb_nb: Number of Ready/Busy lines available + * @need_system_controller: Indicates if the SoC needs to have access to the + * system controller (ie. to enable the NAND controller) + * @legacy_of_bindings: Indicates if DT parsing must be done using the old + * fashion way + * @is_nfcv2: NFCv2 has numerous enhancements compared to NFCv1, ie. + * BCH error detection and correction algorithm, + * NDCB3 register has been added + * @use_dma: Use dma for data transfers + */ +struct marvell_nfc_caps { + unsigned int max_cs_nb; + unsigned int max_rb_nb; + bool need_system_controller; + bool legacy_of_bindings; + bool is_nfcv2; + bool use_dma; +}; + +/** + * NAND controller structure: stores Marvell NAND controller information + * + * @controller: Base controller structure + * @dev: Parent device (used to print error messages) + * @regs: NAND controller registers + * @ecc_clk: ECC block clock, two times the NAND controller clock + * @complete: Completion object to wait for NAND controller events + * @assigned_cs: Bitmask describing already assigned CS lines + * @chips: List containing all the NAND chips attached to + * this NAND controller + * @caps: NAND controller capabilities for each compatible string + * @dma_chan: DMA channel (NFCv1 only) + * @dma_buf: 32-bit aligned buffer for DMA transfers (NFCv1 only) + */ +struct marvell_nfc { + struct nand_hw_control controller; + struct device *dev; + void __iomem *regs; + struct clk *ecc_clk; + struct completion complete; + unsigned long assigned_cs; + struct list_head chips; + struct nand_chip *selected_chip; + const struct marvell_nfc_caps *caps; + + /* DMA (NFCv1 only) */ + bool use_dma; + struct dma_chan *dma_chan; + u8 *dma_buf; +}; + +static inline struct marvell_nfc *to_marvell_nfc(struct nand_hw_control *ctrl) +{ + return container_of(ctrl, struct marvell_nfc, controller); +} + +/** + * NAND controller timings expressed in NAND Controller clock cycles + * + * @tRP: ND_nRE pulse width + * @tRH: ND_nRE high duration + * @tWP: ND_nWE pulse time + * @tWH: ND_nWE high duration + * @tCS: Enable signal setup time + * @tCH: Enable signal hold time + * @tADL: Address to write data delay + * @tAR: ND_ALE low to ND_nRE low delay + * @tWHR: ND_nWE high to ND_nRE low for status read + * @tRHW: ND_nRE high duration, read to write delay + * @tR: ND_nWE high to ND_nRE low for read + */ +struct marvell_nfc_timings { + /* NDTR0 fields */ + unsigned int tRP; + unsigned int tRH; + unsigned int tWP; + unsigned int tWH; + unsigned int tCS; + unsigned int tCH; + unsigned int tADL; + /* NDTR1 fields */ + unsigned int tAR; + unsigned int tWHR; + unsigned int tRHW; + unsigned int tR; +}; + +/** + * Derives a duration in numbers of clock cycles. + * + * @ps: Duration in pico-seconds + * @period_ns: Clock period in nano-seconds + * + * Convert the duration in nano-seconds, then divide by the period and + * return the number of clock periods. + */ +#define TO_CYCLES(ps, period_ns) (DIV_ROUND_UP(ps / 1000, period_ns)) + +/** + * NAND driver structure filled during the parsing of the ->exec_op() subop + * subset of instructions. + * + * @ndcb: Array of values written to NDCBx registers + * @cle_ale_delay_ns: Optional delay after the last CMD or ADDR cycle + * @rdy_timeout_ms: Timeout for waits on Ready/Busy pin + * @rdy_delay_ns: Optional delay after waiting for the RB pin + * @data_delay_ns: Optional delay after the data xfer + * @data_instr_idx: Index of the data instruction in the subop + * @data_instr: Pointer to the data instruction in the subop + */ +struct marvell_nfc_op { + u32 ndcb[4]; + unsigned int cle_ale_delay_ns; + unsigned int rdy_timeout_ms; + unsigned int rdy_delay_ns; + unsigned int data_delay_ns; + unsigned int data_instr_idx; + const struct nand_op_instr *data_instr; +}; + +/* + * Internal helper to conditionnally apply a delay (from the above structure, + * most of the time). + */ +static void cond_delay(unsigned int ns) +{ + if (!ns) + return; + + if (ns < 10000) + ndelay(ns); + else + udelay(DIV_ROUND_UP(ns, 1000)); +} + +/* + * The controller has many flags that could generate interrupts, most of them + * are disabled and polling is used. For the very slow signals, using interrupts + * may relax the CPU charge. + */ +static void marvell_nfc_disable_int(struct marvell_nfc *nfc, u32 int_mask) +{ + u32 reg; + + /* Writing 1 disables the interrupt */ + reg = readl_relaxed(nfc->regs + NDCR); + writel_relaxed(reg | int_mask, nfc->regs + NDCR); +} + +static void marvell_nfc_enable_int(struct marvell_nfc *nfc, u32 int_mask) +{ + u32 reg; + + /* Writing 0 enables the interrupt */ + reg = readl_relaxed(nfc->regs + NDCR); + writel_relaxed(reg & ~int_mask, nfc->regs + NDCR); +} + +static void marvell_nfc_clear_int(struct marvell_nfc *nfc, u32 int_mask) +{ + writel_relaxed(int_mask, nfc->regs + NDSR); +} + +static void marvell_nfc_force_byte_access(struct nand_chip *chip, + bool force_8bit) +{ + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + u32 ndcr; + + /* + * Callers of this function do not verify if the NAND is using a 16-bit + * an 8-bit bus for normal operations, so we need to take care of that + * here by leaving the configuration unchanged if the NAND does not have + * the NAND_BUSWIDTH_16 flag set. + */ + if (!(chip->options & NAND_BUSWIDTH_16)) + return; + + ndcr = readl_relaxed(nfc->regs + NDCR); + + if (force_8bit) + ndcr &= ~(NDCR_DWIDTH_M | NDCR_DWIDTH_C); + else + ndcr |= NDCR_DWIDTH_M | NDCR_DWIDTH_C; + + writel_relaxed(ndcr, nfc->regs + NDCR); +} + +static int marvell_nfc_wait_ndrun(struct nand_chip *chip) +{ + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + u32 val; + int ret; + + /* + * The command is being processed, wait for the ND_RUN bit to be + * cleared by the NFC. If not, we must clear it by hand. + */ + ret = readl_relaxed_poll_timeout(nfc->regs + NDCR, val, + (val & NDCR_ND_RUN) == 0, + POLL_PERIOD, POLL_TIMEOUT); + if (ret) { + dev_err(nfc->dev, "Timeout on NAND controller run mode\n"); + writel_relaxed(readl(nfc->regs + NDCR) & ~NDCR_ND_RUN, + nfc->regs + NDCR); + return ret; + } + + return 0; +} + +/* + * Any time a command has to be sent to the controller, the following sequence + * has to be followed: + * - call marvell_nfc_prepare_cmd() + * -> activate the ND_RUN bit that will kind of 'start a job' + * -> wait the signal indicating the NFC is waiting for a command + * - send the command (cmd and address cycles) + * - enventually send or receive the data + * - call marvell_nfc_end_cmd() with the corresponding flag + * -> wait the flag to be triggered or cancel the job with a timeout + * + * The following helpers are here to factorize the code a bit so that + * specialized functions responsible for executing the actual NAND + * operations do not have to replicate the same code blocks. + */ +static int marvell_nfc_prepare_cmd(struct nand_chip *chip) +{ + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + u32 ndcr, val; + int ret; + + /* Poll ND_RUN and clear NDSR before issuing any command */ + ret = marvell_nfc_wait_ndrun(chip); + if (ret) { + dev_err(nfc->dev, "Last operation did not suceed\n"); + return ret; + } + + ndcr = readl_relaxed(nfc->regs + NDCR); + writel_relaxed(readl(nfc->regs + NDSR), nfc->regs + NDSR); + + /* Assert ND_RUN bit and wait the NFC to be ready */ + writel_relaxed(ndcr | NDCR_ND_RUN, nfc->regs + NDCR); + ret = readl_relaxed_poll_timeout(nfc->regs + NDSR, val, + val & NDSR_WRCMDREQ, + POLL_PERIOD, POLL_TIMEOUT); + if (ret) { + dev_err(nfc->dev, "Timeout on WRCMDRE\n"); + return -ETIMEDOUT; + } + + /* Command may be written, clear WRCMDREQ status bit */ + writel_relaxed(NDSR_WRCMDREQ, nfc->regs + NDSR); + + return 0; +} + +static void marvell_nfc_send_cmd(struct nand_chip *chip, + struct marvell_nfc_op *nfc_op) +{ + struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip); + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + + dev_dbg(nfc->dev, "\nNDCR: 0x%08x\n" + "NDCB0: 0x%08x\nNDCB1: 0x%08x\nNDCB2: 0x%08x\nNDCB3: 0x%08x\n", + (u32)readl_relaxed(nfc->regs + NDCR), nfc_op->ndcb[0], + nfc_op->ndcb[1], nfc_op->ndcb[2], nfc_op->ndcb[3]); + + writel_relaxed(to_nand_sel(marvell_nand)->ndcb0_csel | nfc_op->ndcb[0], + nfc->regs + NDCB0); + writel_relaxed(nfc_op->ndcb[1], nfc->regs + NDCB0); + writel(nfc_op->ndcb[2], nfc->regs + NDCB0); + + /* + * Write NDCB0 four times only if LEN_OVRD is set or if ADDR6 or ADDR7 + * fields are used (only available on NFCv2). + */ + if (nfc_op->ndcb[0] & NDCB0_LEN_OVRD || + NDCB0_ADDR_GET_NUM_CYC(nfc_op->ndcb[0]) >= 6) { + if (!WARN_ON_ONCE(!nfc->caps->is_nfcv2)) + writel(nfc_op->ndcb[3], nfc->regs + NDCB0); + } +} + +static int marvell_nfc_end_cmd(struct nand_chip *chip, int flag, + const char *label) +{ + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + u32 val; + int ret; + + ret = readl_relaxed_poll_timeout(nfc->regs + NDSR, val, + val & flag, + POLL_PERIOD, POLL_TIMEOUT); + + if (ret) { + dev_err(nfc->dev, "Timeout on %s (NDSR: 0x%08x)\n", + label, val); + if (nfc->dma_chan) + dmaengine_terminate_all(nfc->dma_chan); + return ret; + } + + /* + * DMA function uses this helper to poll on CMDD bits without wanting + * them to be cleared. + */ + if (nfc->use_dma && (readl_relaxed(nfc->regs + NDCR) & NDCR_DMA_EN)) + return 0; + + writel_relaxed(flag, nfc->regs + NDSR); + + return 0; +} + +static int marvell_nfc_wait_cmdd(struct nand_chip *chip) +{ + struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip); + int cs_flag = NDSR_CMDD(to_nand_sel(marvell_nand)->ndcb0_csel); + + return marvell_nfc_end_cmd(chip, cs_flag, "CMDD"); +} + +static int marvell_nfc_wait_op(struct nand_chip *chip, unsigned int timeout_ms) +{ + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + int ret; + + /* Timeout is expressed in ms */ + if (!timeout_ms) + timeout_ms = IRQ_TIMEOUT; + + init_completion(&nfc->complete); + + marvell_nfc_enable_int(nfc, NDCR_RDYM); + ret = wait_for_completion_timeout(&nfc->complete, + msecs_to_jiffies(timeout_ms)); + marvell_nfc_disable_int(nfc, NDCR_RDYM); + marvell_nfc_clear_int(nfc, NDSR_RDY(0) | NDSR_RDY(1)); + if (!ret) { + dev_err(nfc->dev, "Timeout waiting for RB signal\n"); + return -ETIMEDOUT; + } + + return 0; +} + +static void marvell_nfc_select_chip(struct mtd_info *mtd, int die_nr) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip); + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + u32 ndcr_generic; + + if (chip == nfc->selected_chip && die_nr == marvell_nand->selected_die) + return; + + if (die_nr < 0 || die_nr >= marvell_nand->nsels) { + nfc->selected_chip = NULL; + marvell_nand->selected_die = -1; + return; + } + + /* + * Do not change the timing registers when using the DT property + * marvell,nand-keep-config; in that case ->ndtr0 and ->ndtr1 from the + * marvell_nand structure are supposedly empty. + */ + writel_relaxed(marvell_nand->ndtr0, nfc->regs + NDTR0); + writel_relaxed(marvell_nand->ndtr1, nfc->regs + NDTR1); + + /* + * Reset the NDCR register to a clean state for this particular chip, + * also clear ND_RUN bit. + */ + ndcr_generic = readl_relaxed(nfc->regs + NDCR) & + NDCR_GENERIC_FIELDS_MASK & ~NDCR_ND_RUN; + writel_relaxed(ndcr_generic | marvell_nand->ndcr, nfc->regs + NDCR); + + /* Also reset the interrupt status register */ + marvell_nfc_clear_int(nfc, NDCR_ALL_INT); + + nfc->selected_chip = chip; + marvell_nand->selected_die = die_nr; +} + +static irqreturn_t marvell_nfc_isr(int irq, void *dev_id) +{ + struct marvell_nfc *nfc = dev_id; + u32 st = readl_relaxed(nfc->regs + NDSR); + u32 ien = (~readl_relaxed(nfc->regs + NDCR)) & NDCR_ALL_INT; + + /* + * RDY interrupt mask is one bit in NDCR while there are two status + * bit in NDSR (RDY[cs0/cs2] and RDY[cs1/cs3]). + */ + if (st & NDSR_RDY(1)) + st |= NDSR_RDY(0); + + if (!(st & ien)) + return IRQ_NONE; + + marvell_nfc_disable_int(nfc, st & NDCR_ALL_INT); + + if (!(st & (NDSR_RDDREQ | NDSR_WRDREQ | NDSR_WRCMDREQ))) + complete(&nfc->complete); + + return IRQ_HANDLED; +} + +/* HW ECC related functions */ +static void marvell_nfc_enable_hw_ecc(struct nand_chip *chip) +{ + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + u32 ndcr = readl_relaxed(nfc->regs + NDCR); + + if (!(ndcr & NDCR_ECC_EN)) { + writel_relaxed(ndcr | NDCR_ECC_EN, nfc->regs + NDCR); + + /* + * When enabling BCH, set threshold to 0 to always know the + * number of corrected bitflips. + */ + if (chip->ecc.algo == NAND_ECC_BCH) + writel_relaxed(NDECCCTRL_BCH_EN, nfc->regs + NDECCCTRL); + } +} + +static void marvell_nfc_disable_hw_ecc(struct nand_chip *chip) +{ + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + u32 ndcr = readl_relaxed(nfc->regs + NDCR); + + if (ndcr & NDCR_ECC_EN) { + writel_relaxed(ndcr & ~NDCR_ECC_EN, nfc->regs + NDCR); + if (chip->ecc.algo == NAND_ECC_BCH) + writel_relaxed(0, nfc->regs + NDECCCTRL); + } +} + +/* DMA related helpers */ +static void marvell_nfc_enable_dma(struct marvell_nfc *nfc) +{ + u32 reg; + + reg = readl_relaxed(nfc->regs + NDCR); + writel_relaxed(reg | NDCR_DMA_EN, nfc->regs + NDCR); +} + +static void marvell_nfc_disable_dma(struct marvell_nfc *nfc) +{ + u32 reg; + + reg = readl_relaxed(nfc->regs + NDCR); + writel_relaxed(reg & ~NDCR_DMA_EN, nfc->regs + NDCR); +} + +/* Read/write PIO/DMA accessors */ +static int marvell_nfc_xfer_data_dma(struct marvell_nfc *nfc, + enum dma_data_direction direction, + unsigned int len) +{ + unsigned int dma_len = min_t(int, ALIGN(len, 32), MAX_CHUNK_SIZE); + struct dma_async_tx_descriptor *tx; + struct scatterlist sg; + dma_cookie_t cookie; + int ret; + + marvell_nfc_enable_dma(nfc); + /* Prepare the DMA transfer */ + sg_init_one(&sg, nfc->dma_buf, dma_len); + dma_map_sg(nfc->dma_chan->device->dev, &sg, 1, direction); + tx = dmaengine_prep_slave_sg(nfc->dma_chan, &sg, 1, + direction == DMA_FROM_DEVICE ? + DMA_DEV_TO_MEM : DMA_MEM_TO_DEV, + DMA_PREP_INTERRUPT); + if (!tx) { + dev_err(nfc->dev, "Could not prepare DMA S/G list\n"); + return -ENXIO; + } + + /* Do the task and wait for it to finish */ + cookie = dmaengine_submit(tx); + ret = dma_submit_error(cookie); + if (ret) + return -EIO; + + dma_async_issue_pending(nfc->dma_chan); + ret = marvell_nfc_wait_cmdd(nfc->selected_chip); + dma_unmap_sg(nfc->dma_chan->device->dev, &sg, 1, direction); + marvell_nfc_disable_dma(nfc); + if (ret) { + dev_err(nfc->dev, "Timeout waiting for DMA (status: %d)\n", + dmaengine_tx_status(nfc->dma_chan, cookie, NULL)); + dmaengine_terminate_all(nfc->dma_chan); + return -ETIMEDOUT; + } + + return 0; +} + +static int marvell_nfc_xfer_data_in_pio(struct marvell_nfc *nfc, u8 *in, + unsigned int len) +{ + unsigned int last_len = len % FIFO_DEPTH; + unsigned int last_full_offset = round_down(len, FIFO_DEPTH); + int i; + + for (i = 0; i < last_full_offset; i += FIFO_DEPTH) + ioread32_rep(nfc->regs + NDDB, in + i, FIFO_REP(FIFO_DEPTH)); + + if (last_len) { + u8 tmp_buf[FIFO_DEPTH]; + + ioread32_rep(nfc->regs + NDDB, tmp_buf, FIFO_REP(FIFO_DEPTH)); + memcpy(in + last_full_offset, tmp_buf, last_len); + } + + return 0; +} + +static int marvell_nfc_xfer_data_out_pio(struct marvell_nfc *nfc, const u8 *out, + unsigned int len) +{ + unsigned int last_len = len % FIFO_DEPTH; + unsigned int last_full_offset = round_down(len, FIFO_DEPTH); + int i; + + for (i = 0; i < last_full_offset; i += FIFO_DEPTH) + iowrite32_rep(nfc->regs + NDDB, out + i, FIFO_REP(FIFO_DEPTH)); + + if (last_len) { + u8 tmp_buf[FIFO_DEPTH]; + + memcpy(tmp_buf, out + last_full_offset, last_len); + iowrite32_rep(nfc->regs + NDDB, tmp_buf, FIFO_REP(FIFO_DEPTH)); + } + + return 0; +} + +static void marvell_nfc_check_empty_chunk(struct nand_chip *chip, + u8 *data, int data_len, + u8 *spare, int spare_len, + u8 *ecc, int ecc_len, + unsigned int *max_bitflips) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + int bf; + + /* + * Blank pages (all 0xFF) that have not been written may be recognized + * as bad if bitflips occur, so whenever an uncorrectable error occurs, + * check if the entire page (with ECC bytes) is actually blank or not. + */ + if (!data) + data_len = 0; + if (!spare) + spare_len = 0; + if (!ecc) + ecc_len = 0; + + bf = nand_check_erased_ecc_chunk(data, data_len, ecc, ecc_len, + spare, spare_len, chip->ecc.strength); + if (bf < 0) { + mtd->ecc_stats.failed++; + return; + } + + /* Update the stats and max_bitflips */ + mtd->ecc_stats.corrected += bf; + *max_bitflips = max_t(unsigned int, *max_bitflips, bf); +} + +/* + * Check a chunk is correct or not according to hardware ECC engine. + * mtd->ecc_stats.corrected is updated, as well as max_bitflips, however + * mtd->ecc_stats.failure is not, the function will instead return a non-zero + * value indicating that a check on the emptyness of the subpage must be + * performed before declaring the subpage corrupted. + */ +static int marvell_nfc_hw_ecc_correct(struct nand_chip *chip, + unsigned int *max_bitflips) +{ + struct mtd_info *mtd = nand_to_mtd(chip); + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + int bf = 0; + u32 ndsr; + + ndsr = readl_relaxed(nfc->regs + NDSR); + + /* Check uncorrectable error flag */ + if (ndsr & NDSR_UNCERR) { + writel_relaxed(ndsr, nfc->regs + NDSR); + + /* + * Do not increment ->ecc_stats.failed now, instead, return a + * non-zero value to indicate that this chunk was apparently + * bad, and it should be check to see if it empty or not. If + * the chunk (with ECC bytes) is not declared empty, the calling + * function must increment the failure count. + */ + return -EBADMSG; + } + + /* Check correctable error flag */ + if (ndsr & NDSR_CORERR) { + writel_relaxed(ndsr, nfc->regs + NDSR); + + if (chip->ecc.algo == NAND_ECC_BCH) + bf = NDSR_ERRCNT(ndsr); + else + bf = 1; + } + + /* Update the stats and max_bitflips */ + mtd->ecc_stats.corrected += bf; + *max_bitflips = max_t(unsigned int, *max_bitflips, bf); + + return 0; +} + +/* Hamming read helpers */ +static int marvell_nfc_hw_ecc_hmg_do_read_page(struct nand_chip *chip, + u8 *data_buf, u8 *oob_buf, + bool raw, int page) +{ + struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip); + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout; + struct marvell_nfc_op nfc_op = { + .ndcb[0] = NDCB0_CMD_TYPE(TYPE_READ) | + NDCB0_ADDR_CYC(marvell_nand->addr_cyc) | + NDCB0_DBC | + NDCB0_CMD1(NAND_CMD_READ0) | + NDCB0_CMD2(NAND_CMD_READSTART), + .ndcb[1] = NDCB1_ADDRS_PAGE(page), + .ndcb[2] = NDCB2_ADDR5_PAGE(page), + }; + unsigned int oob_bytes = lt->spare_bytes + (raw ? lt->ecc_bytes : 0); + int ret; + + /* NFCv2 needs more information about the operation being executed */ + if (nfc->caps->is_nfcv2) + nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_MONOLITHIC_RW); + + ret = marvell_nfc_prepare_cmd(chip); + if (ret) + return ret; + + marvell_nfc_send_cmd(chip, &nfc_op); + ret = marvell_nfc_end_cmd(chip, NDSR_RDDREQ, + "RDDREQ while draining FIFO (data/oob)"); + if (ret) + return ret; + + /* + * Read the page then the OOB area. Unlike what is shown in current + * documentation, spare bytes are protected by the ECC engine, and must + * be at the beginning of the OOB area or running this driver on legacy + * systems will prevent the discovery of the BBM/BBT. + */ + if (nfc->use_dma) { + marvell_nfc_xfer_data_dma(nfc, DMA_FROM_DEVICE, + lt->data_bytes + oob_bytes); + memcpy(data_buf, nfc->dma_buf, lt->data_bytes); + memcpy(oob_buf, nfc->dma_buf + lt->data_bytes, oob_bytes); + } else { + marvell_nfc_xfer_data_in_pio(nfc, data_buf, lt->data_bytes); + marvell_nfc_xfer_data_in_pio(nfc, oob_buf, oob_bytes); + } + + ret = marvell_nfc_wait_cmdd(chip); + + return ret; +} + +static int marvell_nfc_hw_ecc_hmg_read_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, u8 *buf, + int oob_required, int page) +{ + return marvell_nfc_hw_ecc_hmg_do_read_page(chip, buf, chip->oob_poi, + true, page); +} + +static int marvell_nfc_hw_ecc_hmg_read_page(struct mtd_info *mtd, + struct nand_chip *chip, + u8 *buf, int oob_required, + int page) +{ + const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout; + unsigned int full_sz = lt->data_bytes + lt->spare_bytes + lt->ecc_bytes; + int max_bitflips = 0, ret; + u8 *raw_buf; + + marvell_nfc_enable_hw_ecc(chip); + marvell_nfc_hw_ecc_hmg_do_read_page(chip, buf, chip->oob_poi, false, + page); + ret = marvell_nfc_hw_ecc_correct(chip, &max_bitflips); + marvell_nfc_disable_hw_ecc(chip); + + if (!ret) + return max_bitflips; + + /* + * When ECC failures are detected, check if the full page has been + * written or not. Ignore the failure if it is actually empty. + */ + raw_buf = kmalloc(full_sz, GFP_KERNEL); + if (!raw_buf) + return -ENOMEM; + + marvell_nfc_hw_ecc_hmg_do_read_page(chip, raw_buf, raw_buf + + lt->data_bytes, true, page); + marvell_nfc_check_empty_chunk(chip, raw_buf, full_sz, NULL, 0, NULL, 0, + &max_bitflips); + kfree(raw_buf); + + return max_bitflips; +} + +/* + * Spare area in Hamming layouts is not protected by the ECC engine (even if + * it appears before the ECC bytes when reading), the ->read_oob_raw() function + * also stands for ->read_oob(). + */ +static int marvell_nfc_hw_ecc_hmg_read_oob_raw(struct mtd_info *mtd, + struct nand_chip *chip, int page) +{ + /* Invalidate page cache */ + chip->pagebuf = -1; + + return marvell_nfc_hw_ecc_hmg_do_read_page(chip, chip->data_buf, + chip->oob_poi, true, page); +} + +/* Hamming write helpers */ +static int marvell_nfc_hw_ecc_hmg_do_write_page(struct nand_chip *chip, + const u8 *data_buf, + const u8 *oob_buf, bool raw, + int page) +{ + struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip); + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout; + struct marvell_nfc_op nfc_op = { + .ndcb[0] = NDCB0_CMD_TYPE(TYPE_WRITE) | + NDCB0_ADDR_CYC(marvell_nand->addr_cyc) | + NDCB0_CMD1(NAND_CMD_SEQIN) | + NDCB0_CMD2(NAND_CMD_PAGEPROG) | + NDCB0_DBC, + .ndcb[1] = NDCB1_ADDRS_PAGE(page), + .ndcb[2] = NDCB2_ADDR5_PAGE(page), + }; + unsigned int oob_bytes = lt->spare_bytes + (raw ? lt->ecc_bytes : 0); + int ret; + + /* NFCv2 needs more information about the operation being executed */ + if (nfc->caps->is_nfcv2) + nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_MONOLITHIC_RW); + + ret = marvell_nfc_prepare_cmd(chip); + if (ret) + return ret; + + marvell_nfc_send_cmd(chip, &nfc_op); + ret = marvell_nfc_end_cmd(chip, NDSR_WRDREQ, + "WRDREQ while loading FIFO (data)"); + if (ret) + return ret; + + /* Write the page then the OOB area */ + if (nfc->use_dma) { + memcpy(nfc->dma_buf, data_buf, lt->data_bytes); + memcpy(nfc->dma_buf + lt->data_bytes, oob_buf, oob_bytes); + marvell_nfc_xfer_data_dma(nfc, DMA_TO_DEVICE, lt->data_bytes + + lt->ecc_bytes + lt->spare_bytes); + } else { + marvell_nfc_xfer_data_out_pio(nfc, data_buf, lt->data_bytes); + marvell_nfc_xfer_data_out_pio(nfc, oob_buf, oob_bytes); + } + + ret = marvell_nfc_wait_cmdd(chip); + if (ret) + return ret; + + ret = marvell_nfc_wait_op(chip, + chip->data_interface.timings.sdr.tPROG_max); + return ret; +} + +static int marvell_nfc_hw_ecc_hmg_write_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, + const u8 *buf, + int oob_required, int page) +{ + return marvell_nfc_hw_ecc_hmg_do_write_page(chip, buf, chip->oob_poi, + true, page); +} + +static int marvell_nfc_hw_ecc_hmg_write_page(struct mtd_info *mtd, + struct nand_chip *chip, + const u8 *buf, + int oob_required, int page) +{ + int ret; + + marvell_nfc_enable_hw_ecc(chip); + ret = marvell_nfc_hw_ecc_hmg_do_write_page(chip, buf, chip->oob_poi, + false, page); + marvell_nfc_disable_hw_ecc(chip); + + return ret; +} + +/* + * Spare area in Hamming layouts is not protected by the ECC engine (even if + * it appears before the ECC bytes when reading), the ->write_oob_raw() function + * also stands for ->write_oob(). + */ +static int marvell_nfc_hw_ecc_hmg_write_oob_raw(struct mtd_info *mtd, + struct nand_chip *chip, + int page) +{ + /* Invalidate page cache */ + chip->pagebuf = -1; + + memset(chip->data_buf, 0xFF, mtd->writesize); + + return marvell_nfc_hw_ecc_hmg_do_write_page(chip, chip->data_buf, + chip->oob_poi, true, page); +} + +/* BCH read helpers */ +static int marvell_nfc_hw_ecc_bch_read_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, u8 *buf, + int oob_required, int page) +{ + const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout; + u8 *oob = chip->oob_poi; + int chunk_size = lt->data_bytes + lt->spare_bytes + lt->ecc_bytes; + int ecc_offset = (lt->full_chunk_cnt * lt->spare_bytes) + + lt->last_spare_bytes; + int data_len = lt->data_bytes; + int spare_len = lt->spare_bytes; + int ecc_len = lt->ecc_bytes; + int chunk; + + if (oob_required) + memset(chip->oob_poi, 0xFF, mtd->oobsize); + + nand_read_page_op(chip, page, 0, NULL, 0); + + for (chunk = 0; chunk < lt->nchunks; chunk++) { + /* Update last chunk length */ + if (chunk >= lt->full_chunk_cnt) { + data_len = lt->last_data_bytes; + spare_len = lt->last_spare_bytes; + ecc_len = lt->last_ecc_bytes; + } + + /* Read data bytes*/ + nand_change_read_column_op(chip, chunk * chunk_size, + buf + (lt->data_bytes * chunk), + data_len, false); + + /* Read spare bytes */ + nand_read_data_op(chip, oob + (lt->spare_bytes * chunk), + spare_len, false); + + /* Read ECC bytes */ + nand_read_data_op(chip, oob + ecc_offset + + (ALIGN(lt->ecc_bytes, 32) * chunk), + ecc_len, false); + } + + return 0; +} + +static void marvell_nfc_hw_ecc_bch_read_chunk(struct nand_chip *chip, int chunk, + u8 *data, unsigned int data_len, + u8 *spare, unsigned int spare_len, + int page) +{ + struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip); + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout; + int i, ret; + struct marvell_nfc_op nfc_op = { + .ndcb[0] = NDCB0_CMD_TYPE(TYPE_READ) | + NDCB0_ADDR_CYC(marvell_nand->addr_cyc) | + NDCB0_LEN_OVRD, + .ndcb[1] = NDCB1_ADDRS_PAGE(page), + .ndcb[2] = NDCB2_ADDR5_PAGE(page), + .ndcb[3] = data_len + spare_len, + }; + + ret = marvell_nfc_prepare_cmd(chip); + if (ret) + return; + + if (chunk == 0) + nfc_op.ndcb[0] |= NDCB0_DBC | + NDCB0_CMD1(NAND_CMD_READ0) | + NDCB0_CMD2(NAND_CMD_READSTART); + + /* + * Trigger the naked read operation only on the last chunk. + * Otherwise, use monolithic read. + */ + if (lt->nchunks == 1 || (chunk < lt->nchunks - 1)) + nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_MONOLITHIC_RW); + else + nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_LAST_NAKED_RW); + + marvell_nfc_send_cmd(chip, &nfc_op); + + /* + * According to the datasheet, when reading from NDDB + * with BCH enabled, after each 32 bytes reads, we + * have to make sure that the NDSR.RDDREQ bit is set. + * + * Drain the FIFO, 8 32-bit reads at a time, and skip + * the polling on the last read. + * + * Length is a multiple of 32 bytes, hence it is a multiple of 8 too. + */ + for (i = 0; i < data_len; i += FIFO_DEPTH * BCH_SEQ_READS) { + marvell_nfc_end_cmd(chip, NDSR_RDDREQ, + "RDDREQ while draining FIFO (data)"); + marvell_nfc_xfer_data_in_pio(nfc, data, + FIFO_DEPTH * BCH_SEQ_READS); + data += FIFO_DEPTH * BCH_SEQ_READS; + } + + for (i = 0; i < spare_len; i += FIFO_DEPTH * BCH_SEQ_READS) { + marvell_nfc_end_cmd(chip, NDSR_RDDREQ, + "RDDREQ while draining FIFO (OOB)"); + marvell_nfc_xfer_data_in_pio(nfc, spare, + FIFO_DEPTH * BCH_SEQ_READS); + spare += FIFO_DEPTH * BCH_SEQ_READS; + } +} + +static int marvell_nfc_hw_ecc_bch_read_page(struct mtd_info *mtd, + struct nand_chip *chip, + u8 *buf, int oob_required, + int page) +{ + const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout; + int data_len = lt->data_bytes, spare_len = lt->spare_bytes, ecc_len; + u8 *data = buf, *spare = chip->oob_poi, *ecc; + int max_bitflips = 0; + u32 failure_mask = 0; + int chunk, ecc_offset_in_page, ret; + + /* + * With BCH, OOB is not fully used (and thus not read entirely), not + * expected bytes could show up at the end of the OOB buffer if not + * explicitly erased. + */ + if (oob_required) + memset(chip->oob_poi, 0xFF, mtd->oobsize); + + marvell_nfc_enable_hw_ecc(chip); + + for (chunk = 0; chunk < lt->nchunks; chunk++) { + /* Update length for the last chunk */ + if (chunk >= lt->full_chunk_cnt) { + data_len = lt->last_data_bytes; + spare_len = lt->last_spare_bytes; + } + + /* Read the chunk and detect number of bitflips */ + marvell_nfc_hw_ecc_bch_read_chunk(chip, chunk, data, data_len, + spare, spare_len, page); + ret = marvell_nfc_hw_ecc_correct(chip, &max_bitflips); + if (ret) + failure_mask |= BIT(chunk); + + data += data_len; + spare += spare_len; + } + + marvell_nfc_disable_hw_ecc(chip); + + if (!failure_mask) + return max_bitflips; + + /* + * Please note that dumping the ECC bytes during a normal read with OOB + * area would add a significant overhead as ECC bytes are "consumed" by + * the controller in normal mode and must be re-read in raw mode. To + * avoid dropping the performances, we prefer not to include them. The + * user should re-read the page in raw mode if ECC bytes are required. + * + * However, for any subpage read error reported by ->correct(), the ECC + * bytes must be read in raw mode and the full subpage must be checked + * to see if it is entirely empty of if there was an actual error. + */ + for (chunk = 0; chunk < lt->nchunks; chunk++) { + /* No failure reported for this chunk, move to the next one */ + if (!(failure_mask & BIT(chunk))) + continue; + + /* Derive ECC bytes positions (in page/buffer) and length */ + ecc = chip->oob_poi + + (lt->full_chunk_cnt * lt->spare_bytes) + + lt->last_spare_bytes + + (chunk * ALIGN(lt->ecc_bytes, 32)); + ecc_offset_in_page = + (chunk * (lt->data_bytes + lt->spare_bytes + + lt->ecc_bytes)) + + (chunk < lt->full_chunk_cnt ? + lt->data_bytes + lt->spare_bytes : + lt->last_data_bytes + lt->last_spare_bytes); + ecc_len = chunk < lt->full_chunk_cnt ? + lt->ecc_bytes : lt->last_ecc_bytes; + + /* Do the actual raw read of the ECC bytes */ + nand_change_read_column_op(chip, ecc_offset_in_page, + ecc, ecc_len, false); + + /* Derive data/spare bytes positions (in buffer) and length */ + data = buf + (chunk * lt->data_bytes); + data_len = chunk < lt->full_chunk_cnt ? + lt->data_bytes : lt->last_data_bytes; + spare = chip->oob_poi + (chunk * (lt->spare_bytes + + lt->ecc_bytes)); + spare_len = chunk < lt->full_chunk_cnt ? + lt->spare_bytes : lt->last_spare_bytes; + + /* Check the entire chunk (data + spare + ecc) for emptyness */ + marvell_nfc_check_empty_chunk(chip, data, data_len, spare, + spare_len, ecc, ecc_len, + &max_bitflips); + } + + return max_bitflips; +} + +static int marvell_nfc_hw_ecc_bch_read_oob_raw(struct mtd_info *mtd, + struct nand_chip *chip, int page) +{ + /* Invalidate page cache */ + chip->pagebuf = -1; + + return chip->ecc.read_page_raw(mtd, chip, chip->data_buf, true, page); +} + +static int marvell_nfc_hw_ecc_bch_read_oob(struct mtd_info *mtd, + struct nand_chip *chip, int page) +{ + /* Invalidate page cache */ + chip->pagebuf = -1; + + return chip->ecc.read_page(mtd, chip, chip->data_buf, true, page); +} + +/* BCH write helpers */ +static int marvell_nfc_hw_ecc_bch_write_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, + const u8 *buf, + int oob_required, int page) +{ + const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout; + int full_chunk_size = lt->data_bytes + lt->spare_bytes + lt->ecc_bytes; + int data_len = lt->data_bytes; + int spare_len = lt->spare_bytes; + int ecc_len = lt->ecc_bytes; + int oob_len = spare_len + ecc_len; + int spare_offset = 0; + int ecc_offset = (lt->full_chunk_cnt * lt->spare_bytes) + + lt->last_spare_bytes; + int chunk; + + nand_prog_page_begin_op(chip, page, 0, NULL, 0); + + for (chunk = 0; chunk < lt->nchunks; chunk++) { + if (chunk >= lt->full_chunk_cnt) { + data_len = lt->last_data_bytes; + spare_len = lt->last_spare_bytes; + ecc_len = lt->last_ecc_bytes; + oob_len = spare_len + ecc_len; + } + + /* Point to the column of the next chunk */ + nand_change_write_column_op(chip, chunk * full_chunk_size, + NULL, 0, false); + + /* Write the data */ + nand_write_data_op(chip, buf + (chunk * lt->data_bytes), + data_len, false); + + if (!oob_required) + continue; + + /* Write the spare bytes */ + if (spare_len) + nand_write_data_op(chip, chip->oob_poi + spare_offset, + spare_len, false); + + /* Write the ECC bytes */ + if (ecc_len) + nand_write_data_op(chip, chip->oob_poi + ecc_offset, + ecc_len, false); + + spare_offset += spare_len; + ecc_offset += ALIGN(ecc_len, 32); + } + + return nand_prog_page_end_op(chip); +} + +static int +marvell_nfc_hw_ecc_bch_write_chunk(struct nand_chip *chip, int chunk, + const u8 *data, unsigned int data_len, + const u8 *spare, unsigned int spare_len, + int page) +{ + struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip); + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout; + int ret; + struct marvell_nfc_op nfc_op = { + .ndcb[0] = NDCB0_CMD_TYPE(TYPE_WRITE) | NDCB0_LEN_OVRD, + .ndcb[3] = data_len + spare_len, + }; + + /* + * First operation dispatches the CMD_SEQIN command, issue the address + * cycles and asks for the first chunk of data. + * All operations in the middle (if any) will issue a naked write and + * also ask for data. + * Last operation (if any) asks for the last chunk of data through a + * last naked write. + */ + if (chunk == 0) { + nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_WRITE_DISPATCH) | + NDCB0_ADDR_CYC(marvell_nand->addr_cyc) | + NDCB0_CMD1(NAND_CMD_SEQIN); + nfc_op.ndcb[1] |= NDCB1_ADDRS_PAGE(page); + nfc_op.ndcb[2] |= NDCB2_ADDR5_PAGE(page); + } else if (chunk < lt->nchunks - 1) { + nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_NAKED_RW); + } else { + nfc_op.ndcb[0] |= NDCB0_CMD_XTYPE(XTYPE_LAST_NAKED_RW); + } + + /* Always dispatch the PAGEPROG command on the last chunk */ + if (chunk == lt->nchunks - 1) + nfc_op.ndcb[0] |= NDCB0_CMD2(NAND_CMD_PAGEPROG) | NDCB0_DBC; + + ret = marvell_nfc_prepare_cmd(chip); + if (ret) + return ret; + + marvell_nfc_send_cmd(chip, &nfc_op); + ret = marvell_nfc_end_cmd(chip, NDSR_WRDREQ, + "WRDREQ while loading FIFO (data)"); + if (ret) + return ret; + + /* Transfer the contents */ + iowrite32_rep(nfc->regs + NDDB, data, FIFO_REP(data_len)); + iowrite32_rep(nfc->regs + NDDB, spare, FIFO_REP(spare_len)); + + return 0; +} + +static int marvell_nfc_hw_ecc_bch_write_page(struct mtd_info *mtd, + struct nand_chip *chip, + const u8 *buf, + int oob_required, int page) +{ + const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout; + const u8 *data = buf; + const u8 *spare = chip->oob_poi; + int data_len = lt->data_bytes; + int spare_len = lt->spare_bytes; + int chunk, ret; + + /* Spare data will be written anyway, so clear it to avoid garbage */ + if (!oob_required) + memset(chip->oob_poi, 0xFF, mtd->oobsize); + + marvell_nfc_enable_hw_ecc(chip); + + for (chunk = 0; chunk < lt->nchunks; chunk++) { + if (chunk >= lt->full_chunk_cnt) { + data_len = lt->last_data_bytes; + spare_len = lt->last_spare_bytes; + } + + marvell_nfc_hw_ecc_bch_write_chunk(chip, chunk, data, data_len, + spare, spare_len, page); + data += data_len; + spare += spare_len; + + /* + * Waiting only for CMDD or PAGED is not enough, ECC are + * partially written. No flag is set once the operation is + * really finished but the ND_RUN bit is cleared, so wait for it + * before stepping into the next command. + */ + marvell_nfc_wait_ndrun(chip); + } + + ret = marvell_nfc_wait_op(chip, + chip->data_interface.timings.sdr.tPROG_max); + + marvell_nfc_disable_hw_ecc(chip); + + if (ret) + return ret; + + return 0; +} + +static int marvell_nfc_hw_ecc_bch_write_oob_raw(struct mtd_info *mtd, + struct nand_chip *chip, + int page) +{ + /* Invalidate page cache */ + chip->pagebuf = -1; + + memset(chip->data_buf, 0xFF, mtd->writesize); + + return chip->ecc.write_page_raw(mtd, chip, chip->data_buf, true, page); +} + +static int marvell_nfc_hw_ecc_bch_write_oob(struct mtd_info *mtd, + struct nand_chip *chip, int page) +{ + /* Invalidate page cache */ + chip->pagebuf = -1; + + memset(chip->data_buf, 0xFF, mtd->writesize); + + return chip->ecc.write_page(mtd, chip, chip->data_buf, true, page); +} + +/* NAND framework ->exec_op() hooks and related helpers */ +static void marvell_nfc_parse_instructions(struct nand_chip *chip, + const struct nand_subop *subop, + struct marvell_nfc_op *nfc_op) +{ + const struct nand_op_instr *instr = NULL; + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + bool first_cmd = true; + unsigned int op_id; + int i; + + /* Reset the input structure as most of its fields will be OR'ed */ + memset(nfc_op, 0, sizeof(struct marvell_nfc_op)); + + for (op_id = 0; op_id < subop->ninstrs; op_id++) { + unsigned int offset, naddrs; + const u8 *addrs; + int len = nand_subop_get_data_len(subop, op_id); + + instr = &subop->instrs[op_id]; + + switch (instr->type) { + case NAND_OP_CMD_INSTR: + if (first_cmd) + nfc_op->ndcb[0] |= + NDCB0_CMD1(instr->ctx.cmd.opcode); + else + nfc_op->ndcb[0] |= + NDCB0_CMD2(instr->ctx.cmd.opcode) | + NDCB0_DBC; + + nfc_op->cle_ale_delay_ns = instr->delay_ns; + first_cmd = false; + break; + + case NAND_OP_ADDR_INSTR: + offset = nand_subop_get_addr_start_off(subop, op_id); + naddrs = nand_subop_get_num_addr_cyc(subop, op_id); + addrs = &instr->ctx.addr.addrs[offset]; + + nfc_op->ndcb[0] |= NDCB0_ADDR_CYC(naddrs); + + for (i = 0; i < min_t(unsigned int, 4, naddrs); i++) + nfc_op->ndcb[1] |= addrs[i] << (8 * i); + + if (naddrs >= 5) + nfc_op->ndcb[2] |= NDCB2_ADDR5_CYC(addrs[4]); + if (naddrs >= 6) + nfc_op->ndcb[3] |= NDCB3_ADDR6_CYC(addrs[5]); + if (naddrs == 7) + nfc_op->ndcb[3] |= NDCB3_ADDR7_CYC(addrs[6]); + + nfc_op->cle_ale_delay_ns = instr->delay_ns; + break; + + case NAND_OP_DATA_IN_INSTR: + nfc_op->data_instr = instr; + nfc_op->data_instr_idx = op_id; + nfc_op->ndcb[0] |= NDCB0_CMD_TYPE(TYPE_READ); + if (nfc->caps->is_nfcv2) { + nfc_op->ndcb[0] |= + NDCB0_CMD_XTYPE(XTYPE_MONOLITHIC_RW) | + NDCB0_LEN_OVRD; + nfc_op->ndcb[3] |= round_up(len, FIFO_DEPTH); + } + nfc_op->data_delay_ns = instr->delay_ns; + break; + + case NAND_OP_DATA_OUT_INSTR: + nfc_op->data_instr = instr; + nfc_op->data_instr_idx = op_id; + nfc_op->ndcb[0] |= NDCB0_CMD_TYPE(TYPE_WRITE); + if (nfc->caps->is_nfcv2) { + nfc_op->ndcb[0] |= + NDCB0_CMD_XTYPE(XTYPE_MONOLITHIC_RW) | + NDCB0_LEN_OVRD; + nfc_op->ndcb[3] |= round_up(len, FIFO_DEPTH); + } + nfc_op->data_delay_ns = instr->delay_ns; + break; + + case NAND_OP_WAITRDY_INSTR: + nfc_op->rdy_timeout_ms = instr->ctx.waitrdy.timeout_ms; + nfc_op->rdy_delay_ns = instr->delay_ns; + break; + } + } +} + +static int marvell_nfc_xfer_data_pio(struct nand_chip *chip, + const struct nand_subop *subop, + struct marvell_nfc_op *nfc_op) +{ + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + const struct nand_op_instr *instr = nfc_op->data_instr; + unsigned int op_id = nfc_op->data_instr_idx; + unsigned int len = nand_subop_get_data_len(subop, op_id); + unsigned int offset = nand_subop_get_data_start_off(subop, op_id); + bool reading = (instr->type == NAND_OP_DATA_IN_INSTR); + int ret; + + if (instr->ctx.data.force_8bit) + marvell_nfc_force_byte_access(chip, true); + + if (reading) { + u8 *in = instr->ctx.data.buf.in + offset; + + ret = marvell_nfc_xfer_data_in_pio(nfc, in, len); + } else { + const u8 *out = instr->ctx.data.buf.out + offset; + + ret = marvell_nfc_xfer_data_out_pio(nfc, out, len); + } + + if (instr->ctx.data.force_8bit) + marvell_nfc_force_byte_access(chip, false); + + return ret; +} + +static int marvell_nfc_monolithic_access_exec(struct nand_chip *chip, + const struct nand_subop *subop) +{ + struct marvell_nfc_op nfc_op; + bool reading; + int ret; + + marvell_nfc_parse_instructions(chip, subop, &nfc_op); + reading = (nfc_op.data_instr->type == NAND_OP_DATA_IN_INSTR); + + ret = marvell_nfc_prepare_cmd(chip); + if (ret) + return ret; + + marvell_nfc_send_cmd(chip, &nfc_op); + ret = marvell_nfc_end_cmd(chip, NDSR_RDDREQ | NDSR_WRDREQ, + "RDDREQ/WRDREQ while draining raw data"); + if (ret) + return ret; + + cond_delay(nfc_op.cle_ale_delay_ns); + + if (reading) { + if (nfc_op.rdy_timeout_ms) { + ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms); + if (ret) + return ret; + } + + cond_delay(nfc_op.rdy_delay_ns); + } + + marvell_nfc_xfer_data_pio(chip, subop, &nfc_op); + ret = marvell_nfc_wait_cmdd(chip); + if (ret) + return ret; + + cond_delay(nfc_op.data_delay_ns); + + if (!reading) { + if (nfc_op.rdy_timeout_ms) { + ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms); + if (ret) + return ret; + } + + cond_delay(nfc_op.rdy_delay_ns); + } + + /* + * NDCR ND_RUN bit should be cleared automatically at the end of each + * operation but experience shows that the behavior is buggy when it + * comes to writes (with LEN_OVRD). Clear it by hand in this case. + */ + if (!reading) { + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + + writel_relaxed(readl(nfc->regs + NDCR) & ~NDCR_ND_RUN, + nfc->regs + NDCR); + } + + return 0; +} + +static int marvell_nfc_naked_access_exec(struct nand_chip *chip, + const struct nand_subop *subop) +{ + struct marvell_nfc_op nfc_op; + int ret; + + marvell_nfc_parse_instructions(chip, subop, &nfc_op); + + /* + * Naked access are different in that they need to be flagged as naked + * by the controller. Reset the controller registers fields that inform + * on the type and refill them according to the ongoing operation. + */ + nfc_op.ndcb[0] &= ~(NDCB0_CMD_TYPE(TYPE_MASK) | + NDCB0_CMD_XTYPE(XTYPE_MASK)); + switch (subop->instrs[0].type) { + case NAND_OP_CMD_INSTR: + nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_NAKED_CMD); + break; + case NAND_OP_ADDR_INSTR: + nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_NAKED_ADDR); + break; + case NAND_OP_DATA_IN_INSTR: + nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_READ) | + NDCB0_CMD_XTYPE(XTYPE_LAST_NAKED_RW); + break; + case NAND_OP_DATA_OUT_INSTR: + nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_WRITE) | + NDCB0_CMD_XTYPE(XTYPE_LAST_NAKED_RW); + break; + default: + /* This should never happen */ + break; + } + + ret = marvell_nfc_prepare_cmd(chip); + if (ret) + return ret; + + marvell_nfc_send_cmd(chip, &nfc_op); + + if (!nfc_op.data_instr) { + ret = marvell_nfc_wait_cmdd(chip); + cond_delay(nfc_op.cle_ale_delay_ns); + return ret; + } + + ret = marvell_nfc_end_cmd(chip, NDSR_RDDREQ | NDSR_WRDREQ, + "RDDREQ/WRDREQ while draining raw data"); + if (ret) + return ret; + + marvell_nfc_xfer_data_pio(chip, subop, &nfc_op); + ret = marvell_nfc_wait_cmdd(chip); + if (ret) + return ret; + + /* + * NDCR ND_RUN bit should be cleared automatically at the end of each + * operation but experience shows that the behavior is buggy when it + * comes to writes (with LEN_OVRD). Clear it by hand in this case. + */ + if (subop->instrs[0].type == NAND_OP_DATA_OUT_INSTR) { + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + + writel_relaxed(readl(nfc->regs + NDCR) & ~NDCR_ND_RUN, + nfc->regs + NDCR); + } + + return 0; +} + +static int marvell_nfc_naked_waitrdy_exec(struct nand_chip *chip, + const struct nand_subop *subop) +{ + struct marvell_nfc_op nfc_op; + int ret; + + marvell_nfc_parse_instructions(chip, subop, &nfc_op); + + ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms); + cond_delay(nfc_op.rdy_delay_ns); + + return ret; +} + +static int marvell_nfc_read_id_type_exec(struct nand_chip *chip, + const struct nand_subop *subop) +{ + struct marvell_nfc_op nfc_op; + int ret; + + marvell_nfc_parse_instructions(chip, subop, &nfc_op); + nfc_op.ndcb[0] &= ~NDCB0_CMD_TYPE(TYPE_READ); + nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_READ_ID); + + ret = marvell_nfc_prepare_cmd(chip); + if (ret) + return ret; + + marvell_nfc_send_cmd(chip, &nfc_op); + ret = marvell_nfc_end_cmd(chip, NDSR_RDDREQ, + "RDDREQ while reading ID"); + if (ret) + return ret; + + cond_delay(nfc_op.cle_ale_delay_ns); + + if (nfc_op.rdy_timeout_ms) { + ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms); + if (ret) + return ret; + } + + cond_delay(nfc_op.rdy_delay_ns); + + marvell_nfc_xfer_data_pio(chip, subop, &nfc_op); + ret = marvell_nfc_wait_cmdd(chip); + if (ret) + return ret; + + cond_delay(nfc_op.data_delay_ns); + + return 0; +} + +static int marvell_nfc_read_status_exec(struct nand_chip *chip, + const struct nand_subop *subop) +{ + struct marvell_nfc_op nfc_op; + int ret; + + marvell_nfc_parse_instructions(chip, subop, &nfc_op); + nfc_op.ndcb[0] &= ~NDCB0_CMD_TYPE(TYPE_READ); + nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_STATUS); + + ret = marvell_nfc_prepare_cmd(chip); + if (ret) + return ret; + + marvell_nfc_send_cmd(chip, &nfc_op); + ret = marvell_nfc_end_cmd(chip, NDSR_RDDREQ, + "RDDREQ while reading status"); + if (ret) + return ret; + + cond_delay(nfc_op.cle_ale_delay_ns); + + if (nfc_op.rdy_timeout_ms) { + ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms); + if (ret) + return ret; + } + + cond_delay(nfc_op.rdy_delay_ns); + + marvell_nfc_xfer_data_pio(chip, subop, &nfc_op); + ret = marvell_nfc_wait_cmdd(chip); + if (ret) + return ret; + + cond_delay(nfc_op.data_delay_ns); + + return 0; +} + +static int marvell_nfc_reset_cmd_type_exec(struct nand_chip *chip, + const struct nand_subop *subop) +{ + struct marvell_nfc_op nfc_op; + int ret; + + marvell_nfc_parse_instructions(chip, subop, &nfc_op); + nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_RESET); + + ret = marvell_nfc_prepare_cmd(chip); + if (ret) + return ret; + + marvell_nfc_send_cmd(chip, &nfc_op); + ret = marvell_nfc_wait_cmdd(chip); + if (ret) + return ret; + + cond_delay(nfc_op.cle_ale_delay_ns); + + ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms); + if (ret) + return ret; + + cond_delay(nfc_op.rdy_delay_ns); + + return 0; +} + +static int marvell_nfc_erase_cmd_type_exec(struct nand_chip *chip, + const struct nand_subop *subop) +{ + struct marvell_nfc_op nfc_op; + int ret; + + marvell_nfc_parse_instructions(chip, subop, &nfc_op); + nfc_op.ndcb[0] |= NDCB0_CMD_TYPE(TYPE_ERASE); + + ret = marvell_nfc_prepare_cmd(chip); + if (ret) + return ret; + + marvell_nfc_send_cmd(chip, &nfc_op); + ret = marvell_nfc_wait_cmdd(chip); + if (ret) + return ret; + + cond_delay(nfc_op.cle_ale_delay_ns); + + ret = marvell_nfc_wait_op(chip, nfc_op.rdy_timeout_ms); + if (ret) + return ret; + + cond_delay(nfc_op.rdy_delay_ns); + + return 0; +} + +static const struct nand_op_parser marvell_nfcv2_op_parser = NAND_OP_PARSER( + /* Monolithic reads/writes */ + NAND_OP_PARSER_PATTERN( + marvell_nfc_monolithic_access_exec, + NAND_OP_PARSER_PAT_CMD_ELEM(false), + NAND_OP_PARSER_PAT_ADDR_ELEM(true, MAX_ADDRESS_CYC_NFCV2), + NAND_OP_PARSER_PAT_CMD_ELEM(true), + NAND_OP_PARSER_PAT_WAITRDY_ELEM(true), + NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, MAX_CHUNK_SIZE)), + NAND_OP_PARSER_PATTERN( + marvell_nfc_monolithic_access_exec, + NAND_OP_PARSER_PAT_CMD_ELEM(false), + NAND_OP_PARSER_PAT_ADDR_ELEM(false, MAX_ADDRESS_CYC_NFCV2), + NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, MAX_CHUNK_SIZE), + NAND_OP_PARSER_PAT_CMD_ELEM(true), + NAND_OP_PARSER_PAT_WAITRDY_ELEM(true)), + /* Naked commands */ + NAND_OP_PARSER_PATTERN( + marvell_nfc_naked_access_exec, + NAND_OP_PARSER_PAT_CMD_ELEM(false)), + NAND_OP_PARSER_PATTERN( + marvell_nfc_naked_access_exec, + NAND_OP_PARSER_PAT_ADDR_ELEM(false, MAX_ADDRESS_CYC_NFCV2)), + NAND_OP_PARSER_PATTERN( + marvell_nfc_naked_access_exec, + NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, MAX_CHUNK_SIZE)), + NAND_OP_PARSER_PATTERN( + marvell_nfc_naked_access_exec, + NAND_OP_PARSER_PAT_DATA_OUT_ELEM(false, MAX_CHUNK_SIZE)), + NAND_OP_PARSER_PATTERN( + marvell_nfc_naked_waitrdy_exec, + NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)), + ); + +static const struct nand_op_parser marvell_nfcv1_op_parser = NAND_OP_PARSER( + /* Naked commands not supported, use a function for each pattern */ + NAND_OP_PARSER_PATTERN( + marvell_nfc_read_id_type_exec, + NAND_OP_PARSER_PAT_CMD_ELEM(false), + NAND_OP_PARSER_PAT_ADDR_ELEM(false, MAX_ADDRESS_CYC_NFCV1), + NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, 8)), + NAND_OP_PARSER_PATTERN( + marvell_nfc_erase_cmd_type_exec, + NAND_OP_PARSER_PAT_CMD_ELEM(false), + NAND_OP_PARSER_PAT_ADDR_ELEM(false, MAX_ADDRESS_CYC_NFCV1), + NAND_OP_PARSER_PAT_CMD_ELEM(false), + NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)), + NAND_OP_PARSER_PATTERN( + marvell_nfc_read_status_exec, + NAND_OP_PARSER_PAT_CMD_ELEM(false), + NAND_OP_PARSER_PAT_DATA_IN_ELEM(false, 1)), + NAND_OP_PARSER_PATTERN( + marvell_nfc_reset_cmd_type_exec, + NAND_OP_PARSER_PAT_CMD_ELEM(false), + NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)), + NAND_OP_PARSER_PATTERN( + marvell_nfc_naked_waitrdy_exec, + NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)), + ); + +static int marvell_nfc_exec_op(struct nand_chip *chip, + const struct nand_operation *op, + bool check_only) +{ + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + + if (nfc->caps->is_nfcv2) + return nand_op_parser_exec_op(chip, &marvell_nfcv2_op_parser, + op, check_only); + else + return nand_op_parser_exec_op(chip, &marvell_nfcv1_op_parser, + op, check_only); +} + +/* + * Layouts were broken in old pxa3xx_nand driver, these are supposed to be + * usable. + */ +static int marvell_nand_ooblayout_ecc(struct mtd_info *mtd, int section, + struct mtd_oob_region *oobregion) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout; + + if (section) + return -ERANGE; + + oobregion->length = (lt->full_chunk_cnt * lt->ecc_bytes) + + lt->last_ecc_bytes; + oobregion->offset = mtd->oobsize - oobregion->length; + + return 0; +} + +static int marvell_nand_ooblayout_free(struct mtd_info *mtd, int section, + struct mtd_oob_region *oobregion) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout; + + if (section) + return -ERANGE; + + /* + * Bootrom looks in bytes 0 & 5 for bad blocks for the + * 4KB page / 4bit BCH combination. + */ + if (mtd->writesize == SZ_4K && lt->data_bytes == SZ_2K) + oobregion->offset = 6; + else + oobregion->offset = 2; + + oobregion->length = (lt->full_chunk_cnt * lt->spare_bytes) + + lt->last_spare_bytes - oobregion->offset; + + return 0; +} + +static const struct mtd_ooblayout_ops marvell_nand_ooblayout_ops = { + .ecc = marvell_nand_ooblayout_ecc, + .free = marvell_nand_ooblayout_free, +}; + +static int marvell_nand_hw_ecc_ctrl_init(struct mtd_info *mtd, + struct nand_ecc_ctrl *ecc) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + const struct marvell_hw_ecc_layout *l; + int i; + + if (!nfc->caps->is_nfcv2 && + (mtd->writesize + mtd->oobsize > MAX_CHUNK_SIZE)) { + dev_err(nfc->dev, + "NFCv1: writesize (%d) cannot be bigger than a chunk (%d)\n", + mtd->writesize, MAX_CHUNK_SIZE - mtd->oobsize); + return -ENOTSUPP; + } + + to_marvell_nand(chip)->layout = NULL; + for (i = 0; i < ARRAY_SIZE(marvell_nfc_layouts); i++) { + l = &marvell_nfc_layouts[i]; + if (mtd->writesize == l->writesize && + ecc->size == l->chunk && ecc->strength == l->strength) { + to_marvell_nand(chip)->layout = l; + break; + } + } + + if (!to_marvell_nand(chip)->layout || + (!nfc->caps->is_nfcv2 && ecc->strength > 1)) { + dev_err(nfc->dev, + "ECC strength %d at page size %d is not supported\n", + ecc->strength, mtd->writesize); + return -ENOTSUPP; + } + + mtd_set_ooblayout(mtd, &marvell_nand_ooblayout_ops); + ecc->steps = l->nchunks; + ecc->size = l->data_bytes; + + if (ecc->strength == 1) { + chip->ecc.algo = NAND_ECC_HAMMING; + ecc->read_page_raw = marvell_nfc_hw_ecc_hmg_read_page_raw; + ecc->read_page = marvell_nfc_hw_ecc_hmg_read_page; + ecc->read_oob_raw = marvell_nfc_hw_ecc_hmg_read_oob_raw; + ecc->read_oob = ecc->read_oob_raw; + ecc->write_page_raw = marvell_nfc_hw_ecc_hmg_write_page_raw; + ecc->write_page = marvell_nfc_hw_ecc_hmg_write_page; + ecc->write_oob_raw = marvell_nfc_hw_ecc_hmg_write_oob_raw; + ecc->write_oob = ecc->write_oob_raw; + } else { + chip->ecc.algo = NAND_ECC_BCH; + ecc->strength = 16; + ecc->read_page_raw = marvell_nfc_hw_ecc_bch_read_page_raw; + ecc->read_page = marvell_nfc_hw_ecc_bch_read_page; + ecc->read_oob_raw = marvell_nfc_hw_ecc_bch_read_oob_raw; + ecc->read_oob = marvell_nfc_hw_ecc_bch_read_oob; + ecc->write_page_raw = marvell_nfc_hw_ecc_bch_write_page_raw; + ecc->write_page = marvell_nfc_hw_ecc_bch_write_page; + ecc->write_oob_raw = marvell_nfc_hw_ecc_bch_write_oob_raw; + ecc->write_oob = marvell_nfc_hw_ecc_bch_write_oob; + } + + return 0; +} + +static int marvell_nand_ecc_init(struct mtd_info *mtd, + struct nand_ecc_ctrl *ecc) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + int ret; + + if (ecc->mode != NAND_ECC_NONE && (!ecc->size || !ecc->strength)) { + if (chip->ecc_step_ds && chip->ecc_strength_ds) { + ecc->size = chip->ecc_step_ds; + ecc->strength = chip->ecc_strength_ds; + } else { + dev_info(nfc->dev, + "No minimum ECC strength, using 1b/512B\n"); + ecc->size = 512; + ecc->strength = 1; + } + } + + switch (ecc->mode) { + case NAND_ECC_HW: + ret = marvell_nand_hw_ecc_ctrl_init(mtd, ecc); + if (ret) + return ret; + break; + case NAND_ECC_NONE: + case NAND_ECC_SOFT: + if (!nfc->caps->is_nfcv2 && mtd->writesize != SZ_512 && + mtd->writesize != SZ_2K) { + dev_err(nfc->dev, "NFCv1 cannot write %d bytes pages\n", + mtd->writesize); + return -EINVAL; + } + break; + default: + return -EINVAL; + } + + return 0; +} + +static u8 bbt_pattern[] = {'M', 'V', 'B', 'b', 't', '0' }; +static u8 bbt_mirror_pattern[] = {'1', 't', 'b', 'B', 'V', 'M' }; + +static struct nand_bbt_descr bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | + NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 8, + .len = 6, + .veroffs = 14, + .maxblocks = 8, /* Last 8 blocks in each chip */ + .pattern = bbt_pattern +}; + +static struct nand_bbt_descr bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | + NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 8, + .len = 6, + .veroffs = 14, + .maxblocks = 8, /* Last 8 blocks in each chip */ + .pattern = bbt_mirror_pattern +}; + +static int marvell_nfc_setup_data_interface(struct mtd_info *mtd, int chipnr, + const struct nand_data_interface + *conf) +{ + struct nand_chip *chip = mtd_to_nand(mtd); + struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip); + struct marvell_nfc *nfc = to_marvell_nfc(chip->controller); + unsigned int period_ns = 1000000000 / clk_get_rate(nfc->ecc_clk) * 2; + const struct nand_sdr_timings *sdr; + struct marvell_nfc_timings nfc_tmg; + int read_delay; + + sdr = nand_get_sdr_timings(conf); + if (IS_ERR(sdr)) + return PTR_ERR(sdr); + + /* + * SDR timings are given in pico-seconds while NFC timings must be + * expressed in NAND controller clock cycles, which is half of the + * frequency of the accessible ECC clock retrieved by clk_get_rate(). + * This is not written anywhere in the datasheet but was observed + * with an oscilloscope. + * + * NFC datasheet gives equations from which thoses calculations + * are derived, they tend to be slightly more restrictives than the + * given core timings and may improve the overall speed. + */ + nfc_tmg.tRP = TO_CYCLES(DIV_ROUND_UP(sdr->tRC_min, 2), period_ns) - 1; + nfc_tmg.tRH = nfc_tmg.tRP; + nfc_tmg.tWP = TO_CYCLES(DIV_ROUND_UP(sdr->tWC_min, 2), period_ns) - 1; + nfc_tmg.tWH = nfc_tmg.tWP; + nfc_tmg.tCS = TO_CYCLES(sdr->tCS_min, period_ns); + nfc_tmg.tCH = TO_CYCLES(sdr->tCH_min, period_ns) - 1; + nfc_tmg.tADL = TO_CYCLES(sdr->tADL_min, period_ns); + /* + * Read delay is the time of propagation from SoC pins to NFC internal + * logic. With non-EDO timings, this is MIN_RD_DEL_CNT clock cycles. In + * EDO mode, an additional delay of tRH must be taken into account so + * the data is sampled on the falling edge instead of the rising edge. + */ + read_delay = sdr->tRC_min >= 30000 ? + MIN_RD_DEL_CNT : MIN_RD_DEL_CNT + nfc_tmg.tRH; + + nfc_tmg.tAR = TO_CYCLES(sdr->tAR_min, period_ns); + /* + * tWHR and tRHW are supposed to be read to write delays (and vice + * versa) but in some cases, ie. when doing a change column, they must + * be greater than that to be sure tCCS delay is respected. + */ + nfc_tmg.tWHR = TO_CYCLES(max_t(int, sdr->tWHR_min, sdr->tCCS_min), + period_ns) - 2, + nfc_tmg.tRHW = TO_CYCLES(max_t(int, sdr->tRHW_min, sdr->tCCS_min), + period_ns); + + /* Use WAIT_MODE (wait for RB line) instead of only relying on delays */ + nfc_tmg.tR = TO_CYCLES(sdr->tWB_max, period_ns); + + if (chipnr < 0) + return 0; + + marvell_nand->ndtr0 = + NDTR0_TRP(nfc_tmg.tRP) | + NDTR0_TRH(nfc_tmg.tRH) | + NDTR0_ETRP(nfc_tmg.tRP) | + NDTR0_TWP(nfc_tmg.tWP) | + NDTR0_TWH(nfc_tmg.tWH) | + NDTR0_TCS(nfc_tmg.tCS) | + NDTR0_TCH(nfc_tmg.tCH) | + NDTR0_RD_CNT_DEL(read_delay) | + NDTR0_SELCNTR | + NDTR0_TADL(nfc_tmg.tADL); + + marvell_nand->ndtr1 = + NDTR1_TAR(nfc_tmg.tAR) | + NDTR1_TWHR(nfc_tmg.tWHR) | + NDTR1_TRHW(nfc_tmg.tRHW) | + NDTR1_WAIT_MODE | + NDTR1_TR(nfc_tmg.tR); + + return 0; +} + +static int marvell_nand_chip_init(struct device *dev, struct marvell_nfc *nfc, + struct device_node *np) +{ + struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(dev); + struct marvell_nand_chip *marvell_nand; + struct mtd_info *mtd; + struct nand_chip *chip; + int nsels, ret, i; + u32 cs, rb; + + /* + * The legacy "num-cs" property indicates the number of CS on the only + * chip connected to the controller (legacy bindings does not support + * more than one chip). CS are only incremented one by one while the RB + * pin is always the #0. + * + * When not using legacy bindings, a couple of "reg" and "nand-rb" + * properties must be filled. For each chip, expressed as a subnode, + * "reg" points to the CS lines and "nand-rb" to the RB line. + */ + if (pdata) { + nsels = 1; + } else if (nfc->caps->legacy_of_bindings && + !of_get_property(np, "num-cs", &nsels)) { + dev_err(dev, "missing num-cs property\n"); + return -EINVAL; + } else if (!of_get_property(np, "reg", &nsels)) { + dev_err(dev, "missing reg property\n"); + return -EINVAL; + } + + if (!pdata) + nsels /= sizeof(u32); + if (!nsels) { + dev_err(dev, "invalid reg property size\n"); + return -EINVAL; + } + + /* Alloc the nand chip structure */ + marvell_nand = devm_kzalloc(dev, sizeof(*marvell_nand) + + (nsels * + sizeof(struct marvell_nand_chip_sel)), + GFP_KERNEL); + if (!marvell_nand) { + dev_err(dev, "could not allocate chip structure\n"); + return -ENOMEM; + } + + marvell_nand->nsels = nsels; + marvell_nand->selected_die = -1; + + for (i = 0; i < nsels; i++) { + if (pdata || nfc->caps->legacy_of_bindings) { + /* + * Legacy bindings use the CS lines in natural + * order (0, 1, ...) + */ + cs = i; + } else { + /* Retrieve CS id */ + ret = of_property_read_u32_index(np, "reg", i, &cs); + if (ret) { + dev_err(dev, "could not retrieve reg property: %d\n", + ret); + return ret; + } + } + + if (cs >= nfc->caps->max_cs_nb) { + dev_err(dev, "invalid reg value: %u (max CS = %d)\n", + cs, nfc->caps->max_cs_nb); + return -EINVAL; + } + + if (test_and_set_bit(cs, &nfc->assigned_cs)) { + dev_err(dev, "CS %d already assigned\n", cs); + return -EINVAL; + } + + /* + * The cs variable represents the chip select id, which must be + * converted in bit fields for NDCB0 and NDCB2 to select the + * right chip. Unfortunately, due to a lack of information on + * the subject and incoherent documentation, the user should not + * use CS1 and CS3 at all as asserting them is not supported in + * a reliable way (due to multiplexing inside ADDR5 field). + */ + marvell_nand->sels[i].cs = cs; + switch (cs) { + case 0: + case 2: + marvell_nand->sels[i].ndcb0_csel = 0; + break; + case 1: + case 3: + marvell_nand->sels[i].ndcb0_csel = NDCB0_CSEL; + break; + default: + return -EINVAL; + } + + /* Retrieve RB id */ + if (pdata || nfc->caps->legacy_of_bindings) { + /* Legacy bindings always use RB #0 */ + rb = 0; + } else { + ret = of_property_read_u32_index(np, "nand-rb", i, + &rb); + if (ret) { + dev_err(dev, + "could not retrieve RB property: %d\n", + ret); + return ret; + } + } + + if (rb >= nfc->caps->max_rb_nb) { + dev_err(dev, "invalid reg value: %u (max RB = %d)\n", + rb, nfc->caps->max_rb_nb); + return -EINVAL; + } + + marvell_nand->sels[i].rb = rb; + } + + chip = &marvell_nand->chip; + chip->controller = &nfc->controller; + nand_set_flash_node(chip, np); + + chip->exec_op = marvell_nfc_exec_op; + chip->select_chip = marvell_nfc_select_chip; + if (nfc->caps->is_nfcv2 && + !of_property_read_bool(np, "marvell,nand-keep-config")) + chip->setup_data_interface = marvell_nfc_setup_data_interface; + + mtd = nand_to_mtd(chip); + mtd->dev.parent = dev; + + /* + * Default to HW ECC engine mode. If the nand-ecc-mode property is given + * in the DT node, this entry will be overwritten in nand_scan_ident(). + */ + chip->ecc.mode = NAND_ECC_HW; + + /* + * Save a reference value for timing registers before + * ->setup_data_interface() is called. + */ + marvell_nand->ndtr0 = readl_relaxed(nfc->regs + NDTR0); + marvell_nand->ndtr1 = readl_relaxed(nfc->regs + NDTR1); + + chip->options |= NAND_BUSWIDTH_AUTO; + ret = nand_scan_ident(mtd, marvell_nand->nsels, NULL); + if (ret) { + dev_err(dev, "could not identify the nand chip\n"); + return ret; + } + + if (pdata && pdata->flash_bbt) + chip->bbt_options |= NAND_BBT_USE_FLASH; + + if (chip->bbt_options & NAND_BBT_USE_FLASH) { + /* + * We'll use a bad block table stored in-flash and don't + * allow writing the bad block marker to the flash. + */ + chip->bbt_options |= NAND_BBT_NO_OOB_BBM; + chip->bbt_td = &bbt_main_descr; + chip->bbt_md = &bbt_mirror_descr; + } + + /* Save the chip-specific fields of NDCR */ + marvell_nand->ndcr = NDCR_PAGE_SZ(mtd->writesize); + if (chip->options & NAND_BUSWIDTH_16) + marvell_nand->ndcr |= NDCR_DWIDTH_M | NDCR_DWIDTH_C; + + /* + * On small page NANDs, only one cycle is needed to pass the + * column address. + */ + if (mtd->writesize <= 512) { + marvell_nand->addr_cyc = 1; + } else { + marvell_nand->addr_cyc = 2; + marvell_nand->ndcr |= NDCR_RA_START; + } + + /* + * Now add the number of cycles needed to pass the row + * address. + * + * Addressing a chip using CS 2 or 3 should also need the third row + * cycle but due to inconsistance in the documentation and lack of + * hardware to test this situation, this case is not supported. + */ + if (chip->options & NAND_ROW_ADDR_3) + marvell_nand->addr_cyc += 3; + else + marvell_nand->addr_cyc += 2; + + if (pdata) { + chip->ecc.size = pdata->ecc_step_size; + chip->ecc.strength = pdata->ecc_strength; + } + + ret = marvell_nand_ecc_init(mtd, &chip->ecc); + if (ret) { + dev_err(dev, "ECC init failed: %d\n", ret); + return ret; + } + + if (chip->ecc.mode == NAND_ECC_HW) { + /* + * Subpage write not available with hardware ECC, prohibit also + * subpage read as in userspace subpage access would still be + * allowed and subpage write, if used, would lead to numerous + * uncorrectable ECC errors. + */ + chip->options |= NAND_NO_SUBPAGE_WRITE; + } + + if (pdata || nfc->caps->legacy_of_bindings) { + /* + * We keep the MTD name unchanged to avoid breaking platforms + * where the MTD cmdline parser is used and the bootloader + * has not been updated to use the new naming scheme. + */ + mtd->name = "pxa3xx_nand-0"; + } else if (!mtd->name) { + /* + * If the new bindings are used and the bootloader has not been + * updated to pass a new mtdparts parameter on the cmdline, you + * should define the following property in your NAND node, ie: + * + * label = "main-storage"; + * + * This way, mtd->name will be set by the core when + * nand_set_flash_node() is called. + */ + mtd->name = devm_kasprintf(nfc->dev, GFP_KERNEL, + "%s:nand.%d", dev_name(nfc->dev), + marvell_nand->sels[0].cs); + if (!mtd->name) { + dev_err(nfc->dev, "Failed to allocate mtd->name\n"); + return -ENOMEM; + } + } + + ret = nand_scan_tail(mtd); + if (ret) { + dev_err(dev, "nand_scan_tail failed: %d\n", ret); + return ret; + } + + if (pdata) + /* Legacy bindings support only one chip */ + ret = mtd_device_register(mtd, pdata->parts[0], + pdata->nr_parts[0]); + else + ret = mtd_device_register(mtd, NULL, 0); + if (ret) { + dev_err(dev, "failed to register mtd device: %d\n", ret); + nand_release(mtd); + return ret; + } + + list_add_tail(&marvell_nand->node, &nfc->chips); + + return 0; +} + +static int marvell_nand_chips_init(struct device *dev, struct marvell_nfc *nfc) +{ + struct device_node *np = dev->of_node; + struct device_node *nand_np; + int max_cs = nfc->caps->max_cs_nb; + int nchips; + int ret; + + if (!np) + nchips = 1; + else + nchips = of_get_child_count(np); + + if (nchips > max_cs) { + dev_err(dev, "too many NAND chips: %d (max = %d CS)\n", nchips, + max_cs); + return -EINVAL; + } + + /* + * Legacy bindings do not use child nodes to exhibit NAND chip + * properties and layout. Instead, NAND properties are mixed with the + * controller ones, and partitions are defined as direct subnodes of the + * NAND controller node. + */ + if (nfc->caps->legacy_of_bindings) { + ret = marvell_nand_chip_init(dev, nfc, np); + return ret; + } + + for_each_child_of_node(np, nand_np) { + ret = marvell_nand_chip_init(dev, nfc, nand_np); + if (ret) { + of_node_put(nand_np); + return ret; + } + } + + return 0; +} + +static void marvell_nand_chips_cleanup(struct marvell_nfc *nfc) +{ + struct marvell_nand_chip *entry, *temp; + + list_for_each_entry_safe(entry, temp, &nfc->chips, node) { + nand_release(nand_to_mtd(&entry->chip)); + list_del(&entry->node); + } +} + +static int marvell_nfc_init_dma(struct marvell_nfc *nfc) +{ + struct platform_device *pdev = container_of(nfc->dev, + struct platform_device, + dev); + struct dma_slave_config config = {}; + struct resource *r; + dma_cap_mask_t mask; + struct pxad_param param; + int ret; + + if (!IS_ENABLED(CONFIG_PXA_DMA)) { + dev_warn(nfc->dev, + "DMA not enabled in configuration\n"); + return -ENOTSUPP; + } + + ret = dma_set_mask_and_coherent(nfc->dev, DMA_BIT_MASK(32)); + if (ret) + return ret; + + r = platform_get_resource(pdev, IORESOURCE_DMA, 0); + if (!r) { + dev_err(nfc->dev, "No resource defined for data DMA\n"); + return -ENXIO; + } + + param.drcmr = r->start; + param.prio = PXAD_PRIO_LOWEST; + dma_cap_zero(mask); + dma_cap_set(DMA_SLAVE, mask); + nfc->dma_chan = + dma_request_slave_channel_compat(mask, pxad_filter_fn, + ¶m, nfc->dev, + "data"); + if (!nfc->dma_chan) { + dev_err(nfc->dev, + "Unable to request data DMA channel\n"); + return -ENODEV; + } + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!r) + return -ENXIO; + + config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + config.src_addr = r->start + NDDB; + config.dst_addr = r->start + NDDB; + config.src_maxburst = 32; + config.dst_maxburst = 32; + ret = dmaengine_slave_config(nfc->dma_chan, &config); + if (ret < 0) { + dev_err(nfc->dev, "Failed to configure DMA channel\n"); + return ret; + } + + /* + * DMA must act on length multiple of 32 and this length may be + * bigger than the destination buffer. Use this buffer instead + * for DMA transfers and then copy the desired amount of data to + * the provided buffer. + */ + nfc->dma_buf = kmalloc(MAX_CHUNK_SIZE, GFP_DMA); + if (!nfc->dma_buf) + return -ENOMEM; + + nfc->use_dma = true; + + return 0; +} + +static int marvell_nfc_init(struct marvell_nfc *nfc) +{ + struct device_node *np = nfc->dev->of_node; + + /* + * Some SoCs like A7k/A8k need to enable manually the NAND + * controller, gated clocks and reset bits to avoid being bootloader + * dependent. This is done through the use of the System Functions + * registers. + */ + if (nfc->caps->need_system_controller) { + struct regmap *sysctrl_base = + syscon_regmap_lookup_by_phandle(np, + "marvell,system-controller"); + u32 reg; + + if (IS_ERR(sysctrl_base)) + return PTR_ERR(sysctrl_base); + + reg = GENCONF_SOC_DEVICE_MUX_NFC_EN | + GENCONF_SOC_DEVICE_MUX_ECC_CLK_RST | + GENCONF_SOC_DEVICE_MUX_ECC_CORE_RST | + GENCONF_SOC_DEVICE_MUX_NFC_INT_EN; + regmap_write(sysctrl_base, GENCONF_SOC_DEVICE_MUX, reg); + + regmap_read(sysctrl_base, GENCONF_CLK_GATING_CTRL, ®); + reg |= GENCONF_CLK_GATING_CTRL_ND_GATE; + regmap_write(sysctrl_base, GENCONF_CLK_GATING_CTRL, reg); + + regmap_read(sysctrl_base, GENCONF_ND_CLK_CTRL, ®); + reg |= GENCONF_ND_CLK_CTRL_EN; + regmap_write(sysctrl_base, GENCONF_ND_CLK_CTRL, reg); + } + + /* Configure the DMA if appropriate */ + if (!nfc->caps->is_nfcv2) + marvell_nfc_init_dma(nfc); + + /* + * ECC operations and interruptions are only enabled when specifically + * needed. ECC shall not be activated in the early stages (fails probe). + * Arbiter flag, even if marked as "reserved", must be set (empirical). + * SPARE_EN bit must always be set or ECC bytes will not be at the same + * offset in the read page and this will fail the protection. + */ + writel_relaxed(NDCR_ALL_INT | NDCR_ND_ARB_EN | NDCR_SPARE_EN | + NDCR_RD_ID_CNT(NFCV1_READID_LEN), nfc->regs + NDCR); + writel_relaxed(0xFFFFFFFF, nfc->regs + NDSR); + writel_relaxed(0, nfc->regs + NDECCCTRL); + + return 0; +} + +static int marvell_nfc_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct resource *r; + struct marvell_nfc *nfc; + int ret; + int irq; + + nfc = devm_kzalloc(&pdev->dev, sizeof(struct marvell_nfc), + GFP_KERNEL); + if (!nfc) + return -ENOMEM; + + nfc->dev = dev; + nand_hw_control_init(&nfc->controller); + INIT_LIST_HEAD(&nfc->chips); + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + nfc->regs = devm_ioremap_resource(dev, r); + if (IS_ERR(nfc->regs)) + return PTR_ERR(nfc->regs); + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(dev, "failed to retrieve irq\n"); + return irq; + } + + nfc->ecc_clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(nfc->ecc_clk)) + return PTR_ERR(nfc->ecc_clk); + + ret = clk_prepare_enable(nfc->ecc_clk); + if (ret) + return ret; + + marvell_nfc_disable_int(nfc, NDCR_ALL_INT); + marvell_nfc_clear_int(nfc, NDCR_ALL_INT); + ret = devm_request_irq(dev, irq, marvell_nfc_isr, + 0, "marvell-nfc", nfc); + if (ret) + goto unprepare_clk; + + /* Get NAND controller capabilities */ + if (pdev->id_entry) + nfc->caps = (void *)pdev->id_entry->driver_data; + else + nfc->caps = of_device_get_match_data(&pdev->dev); + + if (!nfc->caps) { + dev_err(dev, "Could not retrieve NFC caps\n"); + ret = -EINVAL; + goto unprepare_clk; + } + + /* Init the controller and then probe the chips */ + ret = marvell_nfc_init(nfc); + if (ret) + goto unprepare_clk; + + platform_set_drvdata(pdev, nfc); + + ret = marvell_nand_chips_init(dev, nfc); + if (ret) + goto unprepare_clk; + + return 0; + +unprepare_clk: + clk_disable_unprepare(nfc->ecc_clk); + + return ret; +} + +static int marvell_nfc_remove(struct platform_device *pdev) +{ + struct marvell_nfc *nfc = platform_get_drvdata(pdev); + + marvell_nand_chips_cleanup(nfc); + + if (nfc->use_dma) { + dmaengine_terminate_all(nfc->dma_chan); + dma_release_channel(nfc->dma_chan); + } + + clk_disable_unprepare(nfc->ecc_clk); + + return 0; +} + +static const struct marvell_nfc_caps marvell_armada_8k_nfc_caps = { + .max_cs_nb = 4, + .max_rb_nb = 2, + .need_system_controller = true, + .is_nfcv2 = true, +}; + +static const struct marvell_nfc_caps marvell_armada370_nfc_caps = { + .max_cs_nb = 4, + .max_rb_nb = 2, + .is_nfcv2 = true, +}; + +static const struct marvell_nfc_caps marvell_pxa3xx_nfc_caps = { + .max_cs_nb = 2, + .max_rb_nb = 1, + .use_dma = true, +}; + +static const struct marvell_nfc_caps marvell_armada_8k_nfc_legacy_caps = { + .max_cs_nb = 4, + .max_rb_nb = 2, + .need_system_controller = true, + .legacy_of_bindings = true, + .is_nfcv2 = true, +}; + +static const struct marvell_nfc_caps marvell_armada370_nfc_legacy_caps = { + .max_cs_nb = 4, + .max_rb_nb = 2, + .legacy_of_bindings = true, + .is_nfcv2 = true, +}; + +static const struct marvell_nfc_caps marvell_pxa3xx_nfc_legacy_caps = { + .max_cs_nb = 2, + .max_rb_nb = 1, + .legacy_of_bindings = true, + .use_dma = true, +}; + +static const struct platform_device_id marvell_nfc_platform_ids[] = { + { + .name = "pxa3xx-nand", + .driver_data = (kernel_ulong_t)&marvell_pxa3xx_nfc_legacy_caps, + }, + { /* sentinel */ }, +}; +MODULE_DEVICE_TABLE(platform, marvell_nfc_platform_ids); + +static const struct of_device_id marvell_nfc_of_ids[] = { + { + .compatible = "marvell,armada-8k-nand-controller", + .data = &marvell_armada_8k_nfc_caps, + }, + { + .compatible = "marvell,armada370-nand-controller", + .data = &marvell_armada370_nfc_caps, + }, + { + .compatible = "marvell,pxa3xx-nand-controller", + .data = &marvell_pxa3xx_nfc_caps, + }, + /* Support for old/deprecated bindings: */ + { + .compatible = "marvell,armada-8k-nand", + .data = &marvell_armada_8k_nfc_legacy_caps, + }, + { + .compatible = "marvell,armada370-nand", + .data = &marvell_armada370_nfc_legacy_caps, + }, + { + .compatible = "marvell,pxa3xx-nand", + .data = &marvell_pxa3xx_nfc_legacy_caps, + }, + { /* sentinel */ }, +}; +MODULE_DEVICE_TABLE(of, marvell_nfc_of_ids); + +static struct platform_driver marvell_nfc_driver = { + .driver = { + .name = "marvell-nfc", + .of_match_table = marvell_nfc_of_ids, + }, + .id_table = marvell_nfc_platform_ids, + .probe = marvell_nfc_probe, + .remove = marvell_nfc_remove, +}; +module_platform_driver(marvell_nfc_driver); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("Marvell NAND controller driver"); -- cgit v1.2.3 From dd533734395f0e14db12d82fc64a879c805743dd Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Tue, 9 Jan 2018 11:36:34 +0100 Subject: mtd: nand: use reworked NAND controller driver with Marvell EBU SoCs Choose to compile and embed marvell_nand.c as NAND controller driver instead of the legacy pxa3xx_nand.c for platforms with Marvell EBU SoCs. Signed-off-by: Miquel Raynal Acked-by: Gregory CLEMENT Acked-by: Arnd Bergmann Signed-off-by: Boris Brezillon --- arch/arm/configs/mvebu_v7_defconfig | 2 +- arch/arm64/configs/defconfig | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/configs/mvebu_v7_defconfig b/arch/arm/configs/mvebu_v7_defconfig index 69553704f2dc..4b6e4fd47e5d 100644 --- a/arch/arm/configs/mvebu_v7_defconfig +++ b/arch/arm/configs/mvebu_v7_defconfig @@ -57,7 +57,7 @@ CONFIG_MTD_CFI_STAA=y CONFIG_MTD_PHYSMAP_OF=y CONFIG_MTD_M25P80=y CONFIG_MTD_NAND=y -CONFIG_MTD_NAND_PXA3xx=y +CONFIG_MTD_NAND_MARVELL=y CONFIG_MTD_SPI_NOR=y CONFIG_SRAM=y CONFIG_MTD_UBI=y diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 6356c6da34ea..b20fa9b31efe 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -161,7 +161,7 @@ CONFIG_MTD_BLOCK=y CONFIG_MTD_M25P80=y CONFIG_MTD_NAND=y CONFIG_MTD_NAND_DENALI_DT=y -CONFIG_MTD_NAND_PXA3xx=y +CONFIG_MTD_NAND_MARVELL=y CONFIG_MTD_SPI_NOR=y CONFIG_BLK_DEV_LOOP=y CONFIG_BLK_DEV_NBD=m -- cgit v1.2.3 From 8edfe5fe193a3e43a410ab058d6f5d5cf28c4733 Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Fri, 12 Jan 2018 14:11:53 +0100 Subject: dt-bindings: mtd: gpmc-onenand: Update properties description Compatible property is required for OMAP2+ mtd driver. Also add INT pin gpio description and delete unused dma-channel property. Signed-off-by: Ladislav Michl Reviewed-by: Peter Ujfalusi Acked-by: Roger Quadros Signed-off-by: Boris Brezillon --- Documentation/devicetree/bindings/mtd/gpmc-onenand.txt | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt index b6e8bfd024f4..e9f01a963a0a 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt @@ -9,13 +9,14 @@ Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt Required properties: + - compatible: "ti,omap2-onenand" - reg: The CS line the peripheral is connected to - - gpmc,device-width Width of the ONENAND device connected to the GPMC + - gpmc,device-width: Width of the ONENAND device connected to the GPMC in bytes. Must be 1 or 2. Optional properties: - - dma-channel: DMA Channel index + - int-gpios: GPIO specifier for the INT pin. For inline partition table parsing (optional): @@ -35,6 +36,7 @@ Example for an OMAP3430 board: #size-cells = <1>; onenand@0 { + compatible = "ti,omap2-onenand"; reg = <0 0 0>; /* CS0, offset 0 */ gpmc,device-width = <2>; -- cgit v1.2.3 From 396744b76a89b1cd7681c6b8a7716b545f6cf986 Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Fri, 12 Jan 2018 14:12:56 +0100 Subject: ARM: dts: OMAP2+: Add compatible property to onenand node OMAP onenand nodes are missing compatible property, add it. Signed-off-by: Ladislav Michl Reviewed-by: Peter Ujfalusi Acked-by: Roger Quadros Acked-by: Tony Lindgren Tested-by: Tony Lindgren Tested-by: Aaro Koskinen Signed-off-by: Boris Brezillon --- arch/arm/boot/dts/omap2420-n8x0-common.dtsi | 1 + arch/arm/boot/dts/omap3-n900.dts | 1 + arch/arm/boot/dts/omap3-n950-n9.dtsi | 1 + arch/arm/boot/dts/omap3430-sdp.dts | 1 + 4 files changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/omap2420-n8x0-common.dtsi b/arch/arm/boot/dts/omap2420-n8x0-common.dtsi index 1df3ace3af92..63b0b4921e4e 100644 --- a/arch/arm/boot/dts/omap2420-n8x0-common.dtsi +++ b/arch/arm/boot/dts/omap2420-n8x0-common.dtsi @@ -52,6 +52,7 @@ onenand@0,0 { #address-cells = <1>; #size-cells = <1>; + compatible = "ti,omap2-onenand"; reg = <0 0 0x20000>; /* CS0, offset 0, IO size 128K */ gpmc,sync-read; diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index 669c51c00c00..e7c7b8e50703 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -838,6 +838,7 @@ onenand@0,0 { #address-cells = <1>; #size-cells = <1>; + compatible = "ti,omap2-onenand"; reg = <0 0 0x20000>; /* CS0, offset 0, IO size 128K */ gpmc,sync-read; diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi index 12fbb3da5fce..0d9b85317529 100644 --- a/arch/arm/boot/dts/omap3-n950-n9.dtsi +++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi @@ -367,6 +367,7 @@ onenand@0,0 { #address-cells = <1>; #size-cells = <1>; + compatible = "ti,omap2-onenand"; reg = <0 0 0x20000>; /* CS0, offset 0, IO size 128K */ gpmc,sync-read; diff --git a/arch/arm/boot/dts/omap3430-sdp.dts b/arch/arm/boot/dts/omap3430-sdp.dts index 908951eb5943..d652708f6bef 100644 --- a/arch/arm/boot/dts/omap3430-sdp.dts +++ b/arch/arm/boot/dts/omap3430-sdp.dts @@ -154,6 +154,7 @@ linux,mtd-name= "samsung,kfm2g16q2m-deb8"; #address-cells = <1>; #size-cells = <1>; + compatible = "ti,omap2-onenand"; reg = <2 0 0x20000>; /* CS2, offset 0, IO size 4 */ gpmc,device-width = <2>; -- cgit v1.2.3 From d36005d4a289d31e23be387995df32b8f0554cbc Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Fri, 12 Jan 2018 14:13:19 +0100 Subject: ARM: dts: omap3-igep: Update onenand node timings Update node timings to be compatible with actual chip used - gpmc_cs_show_timings utilized to dump values. Signed-off-by: Ladislav Michl Reviewed-by: Peter Ujfalusi Acked-by: Roger Quadros Acked-by: Tony Lindgren Signed-off-by: Boris Brezillon --- arch/arm/boot/dts/omap3-igep.dtsi | 30 +++++++++++++++--------------- 1 file changed, 15 insertions(+), 15 deletions(-) diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index 4ad7d5565906..f33cc80c9dbc 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -147,32 +147,32 @@ gpmc,sync-read; gpmc,sync-write; gpmc,burst-length = <16>; - gpmc,burst-read; gpmc,burst-wrap; + gpmc,burst-read; gpmc,burst-write; gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */ gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */ gpmc,cs-on-ns = <0>; - gpmc,cs-rd-off-ns = <87>; - gpmc,cs-wr-off-ns = <87>; + gpmc,cs-rd-off-ns = <96>; + gpmc,cs-wr-off-ns = <96>; gpmc,adv-on-ns = <0>; - gpmc,adv-rd-off-ns = <10>; - gpmc,adv-wr-off-ns = <10>; - gpmc,oe-on-ns = <15>; - gpmc,oe-off-ns = <87>; + gpmc,adv-rd-off-ns = <12>; + gpmc,adv-wr-off-ns = <12>; + gpmc,oe-on-ns = <18>; + gpmc,oe-off-ns = <96>; gpmc,we-on-ns = <0>; - gpmc,we-off-ns = <87>; - gpmc,rd-cycle-ns = <112>; - gpmc,wr-cycle-ns = <112>; - gpmc,access-ns = <81>; - gpmc,page-burst-access-ns = <15>; + gpmc,we-off-ns = <96>; + gpmc,rd-cycle-ns = <114>; + gpmc,wr-cycle-ns = <114>; + gpmc,access-ns = <90>; + gpmc,page-burst-access-ns = <12>; gpmc,bus-turnaround-ns = <0>; gpmc,cycle2cycle-delay-ns = <0>; gpmc,wait-monitoring-ns = <0>; - gpmc,clk-activation-ns = <5>; + gpmc,clk-activation-ns = <6>; gpmc,wr-data-mux-bus-ns = <30>; - gpmc,wr-access-ns = <81>; - gpmc,sync-clk-ps = <15000>; + gpmc,wr-access-ns = <90>; + gpmc,sync-clk-ps = <12000>; #address-cells = <1>; #size-cells = <1>; -- cgit v1.2.3 From e6854e029b16bfd059194aabaa738d6d0d982cac Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Fri, 12 Jan 2018 14:13:36 +0100 Subject: mtd: onenand: omap2: Remove regulator support As no platform data user sets regulator_can_sleep, regulator code is no-op and can be deleted. Signed-off-by: Ladislav Michl Reviewed-by: Peter Ujfalusi Reviewed-by: Sebastian Reichel Acked-by: Roger Quadros Tested-by: Tony Lindgren Tested-by: Aaro Koskinen Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/omap2.c | 42 +----------------------------------------- 1 file changed, 1 insertion(+), 41 deletions(-) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index 24a1388d3031..a03e1fe4aa48 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -34,7 +34,6 @@ #include #include #include -#include #include #include @@ -59,7 +58,6 @@ struct omap2_onenand { int dma_channel; int freq; int (*setup)(void __iomem *base, int *freq_ptr); - struct regulator *regulator; u8 flags; }; @@ -583,30 +581,6 @@ static void omap2_onenand_shutdown(struct platform_device *pdev) memset((__force void *)c->onenand.base, 0, ONENAND_BUFRAM_SIZE); } -static int omap2_onenand_enable(struct mtd_info *mtd) -{ - int ret; - struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd); - - ret = regulator_enable(c->regulator); - if (ret != 0) - dev_err(&c->pdev->dev, "can't enable regulator\n"); - - return ret; -} - -static int omap2_onenand_disable(struct mtd_info *mtd) -{ - int ret; - struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd); - - ret = regulator_disable(c->regulator); - if (ret != 0) - dev_err(&c->pdev->dev, "can't disable regulator\n"); - - return ret; -} - static int omap2_onenand_probe(struct platform_device *pdev) { struct omap_onenand_platform_data *pdata; @@ -726,22 +700,11 @@ static int omap2_onenand_probe(struct platform_device *pdev) } } - if (pdata->regulator_can_sleep) { - c->regulator = regulator_get(&pdev->dev, "vonenand"); - if (IS_ERR(c->regulator)) { - dev_err(&pdev->dev, "Failed to get regulator\n"); - r = PTR_ERR(c->regulator); - goto err_release_dma; - } - c->onenand.enable = omap2_onenand_enable; - c->onenand.disable = omap2_onenand_disable; - } - if (pdata->skip_initial_unlocking) this->options |= ONENAND_SKIP_INITIAL_UNLOCKING; if ((r = onenand_scan(&c->mtd, 1)) < 0) - goto err_release_regulator; + goto err_release_dma; r = mtd_device_register(&c->mtd, pdata ? pdata->parts : NULL, pdata ? pdata->nr_parts : 0); @@ -754,8 +717,6 @@ static int omap2_onenand_probe(struct platform_device *pdev) err_release_onenand: onenand_release(&c->mtd); -err_release_regulator: - regulator_put(c->regulator); err_release_dma: if (c->dma_channel != -1) omap_free_dma(c->dma_channel); @@ -779,7 +740,6 @@ static int omap2_onenand_remove(struct platform_device *pdev) struct omap2_onenand *c = dev_get_drvdata(&pdev->dev); onenand_release(&c->mtd); - regulator_put(c->regulator); if (c->dma_channel != -1) omap_free_dma(c->dma_channel); omap2_onenand_shutdown(pdev); -- cgit v1.2.3 From 11066d42952ad254aa59043a9a71737e41705c5f Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Fri, 12 Jan 2018 14:13:56 +0100 Subject: mtd: onenand: omap2: Remove skip initial unlocking support No platform data user sets skip_initial_unlocking, so remove test for this field. Signed-off-by: Ladislav Michl Reviewed-by: Peter Ujfalusi Reviewed-by: Sebastian Reichel Acked-by: Roger Quadros Tested-by: Tony Lindgren Tested-by: Aaro Koskinen Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/omap2.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index a03e1fe4aa48..93bd94337b35 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -700,9 +700,6 @@ static int omap2_onenand_probe(struct platform_device *pdev) } } - if (pdata->skip_initial_unlocking) - this->options |= ONENAND_SKIP_INITIAL_UNLOCKING; - if ((r = onenand_scan(&c->mtd, 1)) < 0) goto err_release_dma; -- cgit v1.2.3 From fafc0b3a9f7b586ae1261b2f78e389bd67df92d7 Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Fri, 12 Jan 2018 14:14:17 +0100 Subject: mtd: onenand: omap2: Remove partitioning support from platform data No platform data user setups partitioning information, so remove. Signed-off-by: Ladislav Michl Reviewed-by: Peter Ujfalusi Reviewed-by: Sebastian Reichel Acked-by: Roger Quadros Tested-by: Tony Lindgren Tested-by: Aaro Koskinen Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/omap2.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index 93bd94337b35..883993bbe40b 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -703,8 +703,7 @@ static int omap2_onenand_probe(struct platform_device *pdev) if ((r = onenand_scan(&c->mtd, 1)) < 0) goto err_release_dma; - r = mtd_device_register(&c->mtd, pdata ? pdata->parts : NULL, - pdata ? pdata->nr_parts : 0); + r = mtd_device_register(&c->mtd, NULL, 0); if (r) goto err_release_onenand; -- cgit v1.2.3 From d120568883a4676852caab2e3545c0d1a623376b Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Fri, 12 Jan 2018 14:14:54 +0100 Subject: mtd: onenand: omap2: Account waiting time as waiting on IO Use wait_for_completion_io_timeout, which has an impact on how the task is accounted in scheduling stats. Signed-off-by: Ladislav Michl Reviewed-by: Peter Ujfalusi Reviewed-by: Sebastian Reichel Acked-by: Roger Quadros Tested-by: Tony Lindgren Tested-by: Aaro Koskinen Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/omap2.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index 883993bbe40b..0e7772e16d75 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -170,9 +170,8 @@ static int omap2_onenand_wait(struct mtd_info *mtd, int state) if (result == 0) { int retry_cnt = 0; retry: - result = wait_for_completion_timeout(&c->irq_done, - msecs_to_jiffies(20)); - if (result == 0) { + if (!wait_for_completion_io_timeout(&c->irq_done, + msecs_to_jiffies(20))) { /* Timeout after 20ms */ ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS); if (ctrl & ONENAND_CTRL_ONGO && -- cgit v1.2.3 From 3621311695f5b1a9396ae95098ac904328eefde7 Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Fri, 12 Jan 2018 14:15:25 +0100 Subject: mtd: onenand: omap2: Simplify the DMA setup for various paths We have 4 functions containing almost identical DMA setup code. Create one function which can set up the DMA for both read and write and use this in place for the setup code in the driver. The new function will use wait_for_completion_io_timeout() and it will figure out the best data_type to be used for the transfer instead of hardwiring 32 or 16 bit data. Signed-off-by: Peter Ujfalusi Signed-off-by: Ladislav Michl Reviewed-by: Sebastian Reichel Acked-by: Roger Quadros Tested-by: Tony Lindgren Tested-by: Aaro Koskinen Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/omap2.c | 109 ++++++++++++++++++-------------------------- 1 file changed, 45 insertions(+), 64 deletions(-) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index 0e7772e16d75..d22163271dc9 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -288,6 +288,33 @@ static inline int omap2_onenand_bufferram_offset(struct mtd_info *mtd, int area) return 0; } +static inline int omap2_onenand_dma_transfer(struct omap2_onenand *c, + dma_addr_t src, dma_addr_t dst, + size_t count) +{ + int data_type = __ffs((src | dst | count)); + + if (data_type > OMAP_DMA_DATA_TYPE_S32) + data_type = OMAP_DMA_DATA_TYPE_S32; + + omap_set_dma_transfer_params(c->dma_channel, data_type, + count / BIT(data_type), 1, 0, 0, 0); + omap_set_dma_src_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC, + src, 0, 0); + omap_set_dma_dest_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC, + dst, 0, 0); + + reinit_completion(&c->dma_done); + omap_start_dma(c->dma_channel); + if (!wait_for_completion_io_timeout(&c->dma_done, + msecs_to_jiffies(20))) { + omap_stop_dma(c->dma_channel); + return -ETIMEDOUT; + } + + return 0; +} + #if defined(CONFIG_ARCH_OMAP3) || defined(MULTI_OMAP2) static int omap3_onenand_read_bufferram(struct mtd_info *mtd, int area, @@ -298,10 +325,9 @@ static int omap3_onenand_read_bufferram(struct mtd_info *mtd, int area, struct onenand_chip *this = mtd->priv; dma_addr_t dma_src, dma_dst; int bram_offset; - unsigned long timeout; void *buf = (void *)buffer; size_t xtra; - volatile unsigned *done; + int ret; bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset; if (bram_offset & 3 || (size_t)buf & 3 || count < 384) @@ -338,25 +364,10 @@ static int omap3_onenand_read_bufferram(struct mtd_info *mtd, int area, goto out_copy; } - omap_set_dma_transfer_params(c->dma_channel, OMAP_DMA_DATA_TYPE_S32, - count >> 2, 1, 0, 0, 0); - omap_set_dma_src_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC, - dma_src, 0, 0); - omap_set_dma_dest_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC, - dma_dst, 0, 0); - - reinit_completion(&c->dma_done); - omap_start_dma(c->dma_channel); - - timeout = jiffies + msecs_to_jiffies(20); - done = &c->dma_done.done; - while (time_before(jiffies, timeout)) - if (*done) - break; - + ret = omap2_onenand_dma_transfer(c, dma_src, dma_dst, count); dma_unmap_single(&c->pdev->dev, dma_dst, count, DMA_FROM_DEVICE); - if (!*done) { + if (ret) { dev_err(&c->pdev->dev, "timeout waiting for DMA\n"); goto out_copy; } @@ -376,9 +387,8 @@ static int omap3_onenand_write_bufferram(struct mtd_info *mtd, int area, struct onenand_chip *this = mtd->priv; dma_addr_t dma_src, dma_dst; int bram_offset; - unsigned long timeout; void *buf = (void *)buffer; - volatile unsigned *done; + int ret; bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset; if (bram_offset & 3 || (size_t)buf & 3 || count < 384) @@ -409,25 +419,10 @@ static int omap3_onenand_write_bufferram(struct mtd_info *mtd, int area, return -1; } - omap_set_dma_transfer_params(c->dma_channel, OMAP_DMA_DATA_TYPE_S32, - count >> 2, 1, 0, 0, 0); - omap_set_dma_src_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC, - dma_src, 0, 0); - omap_set_dma_dest_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC, - dma_dst, 0, 0); - - reinit_completion(&c->dma_done); - omap_start_dma(c->dma_channel); - - timeout = jiffies + msecs_to_jiffies(20); - done = &c->dma_done.done; - while (time_before(jiffies, timeout)) - if (*done) - break; - + ret = omap2_onenand_dma_transfer(c, dma_src, dma_dst, count); dma_unmap_single(&c->pdev->dev, dma_src, count, DMA_TO_DEVICE); - if (!*done) { + if (ret) { dev_err(&c->pdev->dev, "timeout waiting for DMA\n"); goto out_copy; } @@ -466,7 +461,7 @@ static int omap2_onenand_read_bufferram(struct mtd_info *mtd, int area, struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd); struct onenand_chip *this = mtd->priv; dma_addr_t dma_src, dma_dst; - int bram_offset; + int bram_offset, ret; bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset; /* DMA is not used. Revisit PM requirements before enabling it. */ @@ -488,20 +483,13 @@ static int omap2_onenand_read_bufferram(struct mtd_info *mtd, int area, return -1; } - omap_set_dma_transfer_params(c->dma_channel, OMAP_DMA_DATA_TYPE_S32, - count / 4, 1, 0, 0, 0); - omap_set_dma_src_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC, - dma_src, 0, 0); - omap_set_dma_dest_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC, - dma_dst, 0, 0); - - reinit_completion(&c->dma_done); - omap_start_dma(c->dma_channel); - wait_for_completion(&c->dma_done); - + ret = omap2_onenand_dma_transfer(c, dma_src, dma_dst, count); dma_unmap_single(&c->pdev->dev, dma_dst, count, DMA_FROM_DEVICE); - return 0; + if (ret) + dev_err(&c->pdev->dev, "timeout waiting for DMA\n"); + + return ret; } static int omap2_onenand_write_bufferram(struct mtd_info *mtd, int area, @@ -511,7 +499,7 @@ static int omap2_onenand_write_bufferram(struct mtd_info *mtd, int area, struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd); struct onenand_chip *this = mtd->priv; dma_addr_t dma_src, dma_dst; - int bram_offset; + int bram_offset, ret; bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset; /* DMA is not used. Revisit PM requirements before enabling it. */ @@ -533,20 +521,13 @@ static int omap2_onenand_write_bufferram(struct mtd_info *mtd, int area, return -1; } - omap_set_dma_transfer_params(c->dma_channel, OMAP_DMA_DATA_TYPE_S16, - count / 2, 1, 0, 0, 0); - omap_set_dma_src_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC, - dma_src, 0, 0); - omap_set_dma_dest_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC, - dma_dst, 0, 0); - - reinit_completion(&c->dma_done); - omap_start_dma(c->dma_channel); - wait_for_completion(&c->dma_done); - + ret = omap2_onenand_dma_transfer(c, dma_src, dma_dst, count); dma_unmap_single(&c->pdev->dev, dma_src, count, DMA_TO_DEVICE); - return 0; + if (ret) + dev_err(&c->pdev->dev, "timeout waiting for DMA\n"); + + return ret; } #else -- cgit v1.2.3 From fb25070afdf07cc62282c27357dc30ef3d7ef262 Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Fri, 12 Jan 2018 14:15:45 +0100 Subject: mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation Since the very first commit (36cd4fb5d277: "[MTD] [OneNAND] Add OMAP2 / OMAP3 OneNAND driver") DMA is disabled for OMAP2. Later fixes thus went only into OMAP3 specific DMA functions which turned out not to be so OMAP3 specific, so merge those two implementations. Signed-off-by: Ladislav Michl Reviewed-by: Peter Ujfalusi Reviewed-by: Sebastian Reichel Acked-by: Roger Quadros Tested-by: Tony Lindgren Tested-by: Aaro Koskinen Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/omap2.c | 129 ++------------------------------------------ 1 file changed, 4 insertions(+), 125 deletions(-) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index d22163271dc9..36314124488d 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -315,9 +315,7 @@ static inline int omap2_onenand_dma_transfer(struct omap2_onenand *c, return 0; } -#if defined(CONFIG_ARCH_OMAP3) || defined(MULTI_OMAP2) - -static int omap3_onenand_read_bufferram(struct mtd_info *mtd, int area, +static int omap2_onenand_read_bufferram(struct mtd_info *mtd, int area, unsigned char *buffer, int offset, size_t count) { @@ -379,7 +377,7 @@ out_copy: return 0; } -static int omap3_onenand_write_bufferram(struct mtd_info *mtd, int area, +static int omap2_onenand_write_bufferram(struct mtd_info *mtd, int area, const unsigned char *buffer, int offset, size_t count) { @@ -434,120 +432,6 @@ out_copy: return 0; } -#else - -static int omap3_onenand_read_bufferram(struct mtd_info *mtd, int area, - unsigned char *buffer, int offset, - size_t count) -{ - return -ENOSYS; -} - -static int omap3_onenand_write_bufferram(struct mtd_info *mtd, int area, - const unsigned char *buffer, - int offset, size_t count) -{ - return -ENOSYS; -} - -#endif - -#if defined(CONFIG_ARCH_OMAP2) || defined(MULTI_OMAP2) - -static int omap2_onenand_read_bufferram(struct mtd_info *mtd, int area, - unsigned char *buffer, int offset, - size_t count) -{ - struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd); - struct onenand_chip *this = mtd->priv; - dma_addr_t dma_src, dma_dst; - int bram_offset, ret; - - bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset; - /* DMA is not used. Revisit PM requirements before enabling it. */ - if (1 || (c->dma_channel < 0) || - ((void *) buffer >= (void *) high_memory) || (bram_offset & 3) || - (((unsigned int) buffer) & 3) || (count < 1024) || (count & 3)) { - memcpy(buffer, (__force void *)(this->base + bram_offset), - count); - return 0; - } - - dma_src = c->phys_base + bram_offset; - dma_dst = dma_map_single(&c->pdev->dev, buffer, count, - DMA_FROM_DEVICE); - if (dma_mapping_error(&c->pdev->dev, dma_dst)) { - dev_err(&c->pdev->dev, - "Couldn't DMA map a %d byte buffer\n", - count); - return -1; - } - - ret = omap2_onenand_dma_transfer(c, dma_src, dma_dst, count); - dma_unmap_single(&c->pdev->dev, dma_dst, count, DMA_FROM_DEVICE); - - if (ret) - dev_err(&c->pdev->dev, "timeout waiting for DMA\n"); - - return ret; -} - -static int omap2_onenand_write_bufferram(struct mtd_info *mtd, int area, - const unsigned char *buffer, - int offset, size_t count) -{ - struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd); - struct onenand_chip *this = mtd->priv; - dma_addr_t dma_src, dma_dst; - int bram_offset, ret; - - bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset; - /* DMA is not used. Revisit PM requirements before enabling it. */ - if (1 || (c->dma_channel < 0) || - ((void *) buffer >= (void *) high_memory) || (bram_offset & 3) || - (((unsigned int) buffer) & 3) || (count < 1024) || (count & 3)) { - memcpy((__force void *)(this->base + bram_offset), buffer, - count); - return 0; - } - - dma_src = dma_map_single(&c->pdev->dev, (void *) buffer, count, - DMA_TO_DEVICE); - dma_dst = c->phys_base + bram_offset; - if (dma_mapping_error(&c->pdev->dev, dma_src)) { - dev_err(&c->pdev->dev, - "Couldn't DMA map a %d byte buffer\n", - count); - return -1; - } - - ret = omap2_onenand_dma_transfer(c, dma_src, dma_dst, count); - dma_unmap_single(&c->pdev->dev, dma_src, count, DMA_TO_DEVICE); - - if (ret) - dev_err(&c->pdev->dev, "timeout waiting for DMA\n"); - - return ret; -} - -#else - -static int omap2_onenand_read_bufferram(struct mtd_info *mtd, int area, - unsigned char *buffer, int offset, - size_t count) -{ - return -ENOSYS; -} - -static int omap2_onenand_write_bufferram(struct mtd_info *mtd, int area, - const unsigned char *buffer, - int offset, size_t count) -{ - return -ENOSYS; -} - -#endif - static struct platform_driver omap2_onenand_driver; static void omap2_onenand_shutdown(struct platform_device *pdev) @@ -671,13 +555,8 @@ static int omap2_onenand_probe(struct platform_device *pdev) this = &c->onenand; if (c->dma_channel >= 0) { this->wait = omap2_onenand_wait; - if (c->flags & ONENAND_IN_OMAP34XX) { - this->read_bufferram = omap3_onenand_read_bufferram; - this->write_bufferram = omap3_onenand_write_bufferram; - } else { - this->read_bufferram = omap2_onenand_read_bufferram; - this->write_bufferram = omap2_onenand_write_bufferram; - } + this->read_bufferram = omap2_onenand_read_bufferram; + this->write_bufferram = omap2_onenand_write_bufferram; } if ((r = onenand_scan(&c->mtd, 1)) < 0) -- cgit v1.2.3 From 3ed6a4d1de2c5855a9e0164872b6adfd6b7a4215 Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Fri, 12 Jan 2018 14:16:08 +0100 Subject: mtd: onenand: omap2: Convert to use dmaengine for memcpy Do not use the legacy and deprecated omap-dma interface for setting up the memcpy. Signed-off-by: Peter Ujfalusi Signed-off-by: Ladislav Michl Reviewed-by: Sebastian Reichel Acked-by: Roger Quadros Tested-by: Tony Lindgren Tested-by: Aaro Koskinen Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/omap2.c | 80 +++++++++++++++++++++------------------------ 1 file changed, 38 insertions(+), 42 deletions(-) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index 36314124488d..c9ff67100ef4 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -32,6 +32,7 @@ #include #include #include +#include #include #include #include @@ -39,8 +40,6 @@ #include #include -#include - #define DRIVER_NAME "omap2-onenand" #define ONENAND_BUFRAM_SIZE (1024 * 5) @@ -55,17 +54,15 @@ struct omap2_onenand { struct onenand_chip onenand; struct completion irq_done; struct completion dma_done; - int dma_channel; + struct dma_chan *dma_chan; int freq; int (*setup)(void __iomem *base, int *freq_ptr); u8 flags; }; -static void omap2_onenand_dma_cb(int lch, u16 ch_status, void *data) +static void omap2_onenand_dma_complete_func(void *completion) { - struct omap2_onenand *c = data; - - complete(&c->dma_done); + complete(completion); } static irqreturn_t omap2_onenand_interrupt(int irq, void *dev_id) @@ -292,23 +289,31 @@ static inline int omap2_onenand_dma_transfer(struct omap2_onenand *c, dma_addr_t src, dma_addr_t dst, size_t count) { - int data_type = __ffs((src | dst | count)); + struct dma_async_tx_descriptor *tx; + dma_cookie_t cookie; - if (data_type > OMAP_DMA_DATA_TYPE_S32) - data_type = OMAP_DMA_DATA_TYPE_S32; - - omap_set_dma_transfer_params(c->dma_channel, data_type, - count / BIT(data_type), 1, 0, 0, 0); - omap_set_dma_src_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC, - src, 0, 0); - omap_set_dma_dest_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC, - dst, 0, 0); + tx = dmaengine_prep_dma_memcpy(c->dma_chan, dst, src, count, 0); + if (!tx) { + dev_err(&c->pdev->dev, "Failed to prepare DMA memcpy\n"); + return -EIO; + } reinit_completion(&c->dma_done); - omap_start_dma(c->dma_channel); + + tx->callback = omap2_onenand_dma_complete_func; + tx->callback_param = &c->dma_done; + + cookie = tx->tx_submit(tx); + if (dma_submit_error(cookie)) { + dev_err(&c->pdev->dev, "Failed to do DMA tx_submit\n"); + return -EIO; + } + + dma_async_issue_pending(c->dma_chan); + if (!wait_for_completion_io_timeout(&c->dma_done, msecs_to_jiffies(20))) { - omap_stop_dma(c->dma_channel); + dmaengine_terminate_sync(c->dma_chan); return -ETIMEDOUT; } @@ -468,8 +473,7 @@ static int omap2_onenand_probe(struct platform_device *pdev) c->flags = pdata->flags; c->gpmc_cs = pdata->cs; c->gpio_irq = pdata->gpio_irq; - c->dma_channel = pdata->dma_channel; - if (c->dma_channel < 0) { + if (pdata->dma_channel < 0) { /* if -1, don't use DMA */ c->gpio_irq = 0; } @@ -521,25 +525,17 @@ static int omap2_onenand_probe(struct platform_device *pdev) goto err_release_gpio; } - if (c->dma_channel >= 0) { - r = omap_request_dma(0, pdev->dev.driver->name, - omap2_onenand_dma_cb, (void *) c, - &c->dma_channel); - if (r == 0) { - omap_set_dma_write_mode(c->dma_channel, - OMAP_DMA_WRITE_NON_POSTED); - omap_set_dma_src_data_pack(c->dma_channel, 1); - omap_set_dma_src_burst_mode(c->dma_channel, - OMAP_DMA_DATA_BURST_8); - omap_set_dma_dest_data_pack(c->dma_channel, 1); - omap_set_dma_dest_burst_mode(c->dma_channel, - OMAP_DMA_DATA_BURST_8); - } else { + if (pdata->dma_channel >= 0) { + dma_cap_mask_t mask; + + dma_cap_zero(mask); + dma_cap_set(DMA_MEMCPY, mask); + + c->dma_chan = dma_request_channel(mask, NULL, NULL); + if (!c->dma_chan) dev_info(&pdev->dev, "failed to allocate DMA for OneNAND, " "using PIO instead\n"); - c->dma_channel = -1; - } } dev_info(&pdev->dev, "initializing on CS%d, phys base 0x%08lx, virtual " @@ -553,7 +549,7 @@ static int omap2_onenand_probe(struct platform_device *pdev) mtd_set_of_node(&c->mtd, pdata->of_node); this = &c->onenand; - if (c->dma_channel >= 0) { + if (c->dma_chan) { this->wait = omap2_onenand_wait; this->read_bufferram = omap2_onenand_read_bufferram; this->write_bufferram = omap2_onenand_write_bufferram; @@ -573,8 +569,8 @@ static int omap2_onenand_probe(struct platform_device *pdev) err_release_onenand: onenand_release(&c->mtd); err_release_dma: - if (c->dma_channel != -1) - omap_free_dma(c->dma_channel); + if (c->dma_chan) + dma_release_channel(c->dma_chan); if (c->gpio_irq) free_irq(gpio_to_irq(c->gpio_irq), c); err_release_gpio: @@ -595,8 +591,8 @@ static int omap2_onenand_remove(struct platform_device *pdev) struct omap2_onenand *c = dev_get_drvdata(&pdev->dev); onenand_release(&c->mtd); - if (c->dma_channel != -1) - omap_free_dma(c->dma_channel); + if (c->dma_chan) + dma_release_channel(c->dma_chan); omap2_onenand_shutdown(pdev); if (c->gpio_irq) { free_irq(gpio_to_irq(c->gpio_irq), c); -- cgit v1.2.3 From f5229331f13b84389cd71a58ccd5e15e5cb091c2 Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Fri, 12 Jan 2018 14:16:28 +0100 Subject: mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific Second commit in driver history (782b7a367d81: "[MTD] [OneNAND] OMAP3: add delay for GPIO") added quirk for waiting until GPIO line settle. As DMA was disabled for OMAP2 boards, chances are this problem was not OMAP3 specific and as it is just one register read, previous test for SoC type is approximately as expensive as read itself. Make delay unconditional, which allows removing SoC specific code alltogether. Signed-off-by: Ladislav Michl Reviewed-by: Peter Ujfalusi Reviewed-by: Sebastian Reichel Acked-by: Roger Quadros Tested-by: Tony Lindgren Tested-by: Aaro Koskinen Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/omap2.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index c9ff67100ef4..e4857a41760d 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -57,7 +57,6 @@ struct omap2_onenand { struct dma_chan *dma_chan; int freq; int (*setup)(void __iomem *base, int *freq_ptr); - u8 flags; }; static void omap2_onenand_dma_complete_func(void *completion) @@ -148,9 +147,8 @@ static int omap2_onenand_wait(struct mtd_info *mtd, int state) if (!(syscfg & ONENAND_SYS_CFG1_IOBE)) { syscfg |= ONENAND_SYS_CFG1_IOBE; write_reg(c, syscfg, ONENAND_REG_SYS_CFG1); - if (c->flags & ONENAND_IN_OMAP34XX) - /* Add a delay to let GPIO settle */ - syscfg = read_reg(c, ONENAND_REG_SYS_CFG1); + /* Add a delay to let GPIO settle */ + syscfg = read_reg(c, ONENAND_REG_SYS_CFG1); } reinit_completion(&c->irq_done); @@ -470,7 +468,6 @@ static int omap2_onenand_probe(struct platform_device *pdev) init_completion(&c->irq_done); init_completion(&c->dma_done); - c->flags = pdata->flags; c->gpmc_cs = pdata->cs; c->gpio_irq = pdata->gpio_irq; if (pdata->dma_channel < 0) { -- cgit v1.2.3 From bdaca9345d41fd9420995469d27603ea62054691 Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Fri, 12 Jan 2018 14:16:57 +0100 Subject: mtd: onenand: omap2: Decouple DMA enabling from INT pin availability INT pin (gpio_irq) is not really needed for DMA but only for notification when a command that needs wait has completed. DMA memcpy can be still used even without gpio_irq available, so enable it unconditionally. Signed-off-by: Ladislav Michl Reviewed-by: Peter Ujfalusi Tested-by: Tony Lindgren Tested-by: Aaro Koskinen Acked-by: Roger Quadros Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/omap2.c | 52 ++++++++++++++++++--------------------------- 1 file changed, 21 insertions(+), 31 deletions(-) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index e4857a41760d..1cd78a076759 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -152,17 +152,13 @@ static int omap2_onenand_wait(struct mtd_info *mtd, int state) } reinit_completion(&c->irq_done); - if (c->gpio_irq) { - result = gpio_get_value(c->gpio_irq); - if (result == -1) { - ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS); - intr = read_reg(c, ONENAND_REG_INTERRUPT); - wait_err("gpio error", state, ctrl, intr); - return -EIO; - } - } else - result = 0; - if (result == 0) { + result = gpio_get_value(c->gpio_irq); + if (result < 0) { + ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS); + intr = read_reg(c, ONENAND_REG_INTERRUPT); + wait_err("gpio error", state, ctrl, intr); + return -EIO; + } else if (result == 0) { int retry_cnt = 0; retry: if (!wait_for_completion_io_timeout(&c->irq_done, @@ -450,6 +446,7 @@ static void omap2_onenand_shutdown(struct platform_device *pdev) static int omap2_onenand_probe(struct platform_device *pdev) { + dma_cap_mask_t mask; struct omap_onenand_platform_data *pdata; struct omap2_onenand *c; struct onenand_chip *this; @@ -513,31 +510,25 @@ static int omap2_onenand_probe(struct platform_device *pdev) dev_err(&pdev->dev, "Failed to request GPIO%d for " "OneNAND\n", c->gpio_irq); goto err_iounmap; - } - gpio_direction_input(c->gpio_irq); + } + gpio_direction_input(c->gpio_irq); - if ((r = request_irq(gpio_to_irq(c->gpio_irq), - omap2_onenand_interrupt, IRQF_TRIGGER_RISING, - pdev->dev.driver->name, c)) < 0) - goto err_release_gpio; - } + if ((r = request_irq(gpio_to_irq(c->gpio_irq), + omap2_onenand_interrupt, IRQF_TRIGGER_RISING, + pdev->dev.driver->name, c)) < 0) + goto err_release_gpio; - if (pdata->dma_channel >= 0) { - dma_cap_mask_t mask; + this->wait = omap2_onenand_wait; + } - dma_cap_zero(mask); - dma_cap_set(DMA_MEMCPY, mask); + dma_cap_zero(mask); + dma_cap_set(DMA_MEMCPY, mask); - c->dma_chan = dma_request_channel(mask, NULL, NULL); - if (!c->dma_chan) - dev_info(&pdev->dev, - "failed to allocate DMA for OneNAND, " - "using PIO instead\n"); - } + c->dma_chan = dma_request_channel(mask, NULL, NULL); dev_info(&pdev->dev, "initializing on CS%d, phys base 0x%08lx, virtual " - "base %p, freq %d MHz\n", c->gpmc_cs, c->phys_base, - c->onenand.base, c->freq); + "base %p, freq %d MHz, %s mode\n", c->gpmc_cs, c->phys_base, + c->onenand.base, c->freq, c->dma_chan ? "DMA" : "PIO"); c->pdev = pdev; c->mtd.priv = &c->onenand; @@ -547,7 +538,6 @@ static int omap2_onenand_probe(struct platform_device *pdev) this = &c->onenand; if (c->dma_chan) { - this->wait = omap2_onenand_wait; this->read_bufferram = omap2_onenand_read_bufferram; this->write_bufferram = omap2_onenand_write_bufferram; } -- cgit v1.2.3 From a758f50f10cfcf863f95372ff52e0d8d22fda9ba Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Fri, 12 Jan 2018 14:17:25 +0100 Subject: mtd: onenand: omap2: Configure driver from DT Move away from platform data configuration and use pure DT approach. Use generic probe function to deal with OneNAND node and remove now useless gpmc_probe_onenand_child function. Import sync mode timing calculation function from mach-omap2/gpmc-onenand.c Signed-off-by: Ladislav Michl Reviewed-by: Peter Ujfalusi Tested-by: Tony Lindgren Tested-by: Aaro Koskinen Acked-by: Roger Quadros Signed-off-by: Boris Brezillon --- drivers/memory/omap-gpmc.c | 158 ++++++++++++++++++++-------- drivers/mtd/onenand/Kconfig | 4 +- drivers/mtd/onenand/omap2.c | 250 +++++++++++++++++++++++++++----------------- include/linux/omap-gpmc.h | 28 +++++ 4 files changed, 301 insertions(+), 139 deletions(-) diff --git a/drivers/memory/omap-gpmc.c b/drivers/memory/omap-gpmc.c index 0e30ee1c8677..90a66b3f7ae1 100644 --- a/drivers/memory/omap-gpmc.c +++ b/drivers/memory/omap-gpmc.c @@ -32,7 +32,6 @@ #include #include -#include #include @@ -1138,6 +1137,112 @@ struct gpmc_nand_ops *gpmc_omap_get_nand_ops(struct gpmc_nand_regs *reg, int cs) } EXPORT_SYMBOL_GPL(gpmc_omap_get_nand_ops); +static void gpmc_omap_onenand_calc_sync_timings(struct gpmc_timings *t, + struct gpmc_settings *s, + int freq, int latency) +{ + struct gpmc_device_timings dev_t; + const int t_cer = 15; + const int t_avdp = 12; + const int t_cez = 20; /* max of t_cez, t_oez */ + const int t_wpl = 40; + const int t_wph = 30; + int min_gpmc_clk_period, t_ces, t_avds, t_avdh, t_ach, t_aavdh, t_rdyo; + + switch (freq) { + case 104: + min_gpmc_clk_period = 9600; /* 104 MHz */ + t_ces = 3; + t_avds = 4; + t_avdh = 2; + t_ach = 3; + t_aavdh = 6; + t_rdyo = 6; + break; + case 83: + min_gpmc_clk_period = 12000; /* 83 MHz */ + t_ces = 5; + t_avds = 4; + t_avdh = 2; + t_ach = 6; + t_aavdh = 6; + t_rdyo = 9; + break; + case 66: + min_gpmc_clk_period = 15000; /* 66 MHz */ + t_ces = 6; + t_avds = 5; + t_avdh = 2; + t_ach = 6; + t_aavdh = 6; + t_rdyo = 11; + break; + default: + min_gpmc_clk_period = 18500; /* 54 MHz */ + t_ces = 7; + t_avds = 7; + t_avdh = 7; + t_ach = 9; + t_aavdh = 7; + t_rdyo = 15; + break; + } + + /* Set synchronous read timings */ + memset(&dev_t, 0, sizeof(dev_t)); + + if (!s->sync_write) { + dev_t.t_avdp_w = max(t_avdp, t_cer) * 1000; + dev_t.t_wpl = t_wpl * 1000; + dev_t.t_wph = t_wph * 1000; + dev_t.t_aavdh = t_aavdh * 1000; + } + dev_t.ce_xdelay = true; + dev_t.avd_xdelay = true; + dev_t.oe_xdelay = true; + dev_t.we_xdelay = true; + dev_t.clk = min_gpmc_clk_period; + dev_t.t_bacc = dev_t.clk; + dev_t.t_ces = t_ces * 1000; + dev_t.t_avds = t_avds * 1000; + dev_t.t_avdh = t_avdh * 1000; + dev_t.t_ach = t_ach * 1000; + dev_t.cyc_iaa = (latency + 1); + dev_t.t_cez_r = t_cez * 1000; + dev_t.t_cez_w = dev_t.t_cez_r; + dev_t.cyc_aavdh_oe = 1; + dev_t.t_rdyo = t_rdyo * 1000 + min_gpmc_clk_period; + + gpmc_calc_timings(t, s, &dev_t); +} + +int gpmc_omap_onenand_set_timings(struct device *dev, int cs, int freq, + int latency, + struct gpmc_onenand_info *info) +{ + int ret; + struct gpmc_timings gpmc_t; + struct gpmc_settings gpmc_s; + + gpmc_read_settings_dt(dev->of_node, &gpmc_s); + + info->sync_read = gpmc_s.sync_read; + info->sync_write = gpmc_s.sync_write; + info->burst_len = gpmc_s.burst_len; + + if (!gpmc_s.sync_read && !gpmc_s.sync_write) + return 0; + + gpmc_omap_onenand_calc_sync_timings(&gpmc_t, &gpmc_s, freq, latency); + + ret = gpmc_cs_program_settings(cs, &gpmc_s); + if (ret < 0) + return ret; + + return gpmc_cs_set_timings(cs, &gpmc_t, &gpmc_s); +} +EXPORT_SYMBOL_GPL(gpmc_omap_onenand_set_timings); + int gpmc_get_client_irq(unsigned irq_config) { if (!gpmc_irq_domain) { @@ -1916,41 +2021,6 @@ static void __maybe_unused gpmc_read_timings_dt(struct device_node *np, of_property_read_bool(np, "gpmc,time-para-granularity"); } -#if IS_ENABLED(CONFIG_MTD_ONENAND) -static int gpmc_probe_onenand_child(struct platform_device *pdev, - struct device_node *child) -{ - u32 val; - struct omap_onenand_platform_data *gpmc_onenand_data; - - if (of_property_read_u32(child, "reg", &val) < 0) { - dev_err(&pdev->dev, "%pOF has no 'reg' property\n", - child); - return -ENODEV; - } - - gpmc_onenand_data = devm_kzalloc(&pdev->dev, sizeof(*gpmc_onenand_data), - GFP_KERNEL); - if (!gpmc_onenand_data) - return -ENOMEM; - - gpmc_onenand_data->cs = val; - gpmc_onenand_data->of_node = child; - gpmc_onenand_data->dma_channel = -1; - - if (!of_property_read_u32(child, "dma-channel", &val)) - gpmc_onenand_data->dma_channel = val; - - return gpmc_onenand_init(gpmc_onenand_data); -} -#else -static int gpmc_probe_onenand_child(struct platform_device *pdev, - struct device_node *child) -{ - return 0; -} -#endif - /** * gpmc_probe_generic_child - configures the gpmc for a child device * @pdev: pointer to gpmc platform device @@ -2053,6 +2123,16 @@ static int gpmc_probe_generic_child(struct platform_device *pdev, } } + if (of_node_cmp(child->name, "onenand") == 0) { + /* Warn about older DT blobs with no compatible property */ + if (!of_property_read_bool(child, "compatible")) { + dev_warn(&pdev->dev, + "Incompatible OneNAND node: missing compatible"); + ret = -EINVAL; + goto err; + } + } + if (of_device_is_compatible(child, "ti,omap2-nand")) { /* NAND specific setup */ val = 8; @@ -2189,11 +2269,7 @@ static void gpmc_probe_dt_children(struct platform_device *pdev) if (!child->name) continue; - if (of_node_cmp(child->name, "onenand") == 0) - ret = gpmc_probe_onenand_child(pdev, child); - else - ret = gpmc_probe_generic_child(pdev, child); - + ret = gpmc_probe_generic_child(pdev, child); if (ret) { dev_err(&pdev->dev, "failed to probe DT child '%s': %d\n", child->name, ret); diff --git a/drivers/mtd/onenand/Kconfig b/drivers/mtd/onenand/Kconfig index aaeb30458139..9dc15748947b 100644 --- a/drivers/mtd/onenand/Kconfig +++ b/drivers/mtd/onenand/Kconfig @@ -25,9 +25,11 @@ config MTD_ONENAND_GENERIC config MTD_ONENAND_OMAP2 tristate "OneNAND on OMAP2/OMAP3 support" depends on ARCH_OMAP2 || ARCH_OMAP3 + depends on OF || COMPILE_TEST help - Support for a OneNAND flash device connected to an OMAP2/OMAP3 CPU + Support for a OneNAND flash device connected to an OMAP2/OMAP3 SoC via the GPMC memory controller. + Enable dmaengine and gpiolib for better performance. config MTD_ONENAND_SAMSUNG tristate "OneNAND on Samsung SOC controller support" diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index 1cd78a076759..2ce73fb6da1c 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -28,6 +28,8 @@ #include #include #include +#include +#include #include #include #include @@ -35,10 +37,9 @@ #include #include #include -#include +#include #include -#include #define DRIVER_NAME "omap2-onenand" @@ -48,15 +49,12 @@ struct omap2_onenand { struct platform_device *pdev; int gpmc_cs; unsigned long phys_base; - unsigned int mem_size; - int gpio_irq; + struct gpio_desc *int_gpiod; struct mtd_info mtd; struct onenand_chip onenand; struct completion irq_done; struct completion dma_done; struct dma_chan *dma_chan; - int freq; - int (*setup)(void __iomem *base, int *freq_ptr); }; static void omap2_onenand_dma_complete_func(void *completion) @@ -84,6 +82,65 @@ static inline void write_reg(struct omap2_onenand *c, unsigned short value, writew(value, c->onenand.base + reg); } +static int omap2_onenand_set_cfg(struct omap2_onenand *c, + bool sr, bool sw, + int latency, int burst_len) +{ + unsigned short reg = ONENAND_SYS_CFG1_RDY | ONENAND_SYS_CFG1_INT; + + reg |= latency << ONENAND_SYS_CFG1_BRL_SHIFT; + + switch (burst_len) { + case 0: /* continuous */ + break; + case 4: + reg |= ONENAND_SYS_CFG1_BL_4; + break; + case 8: + reg |= ONENAND_SYS_CFG1_BL_8; + break; + case 16: + reg |= ONENAND_SYS_CFG1_BL_16; + break; + case 32: + reg |= ONENAND_SYS_CFG1_BL_32; + break; + default: + return -EINVAL; + } + + if (latency > 5) + reg |= ONENAND_SYS_CFG1_HF; + if (latency > 7) + reg |= ONENAND_SYS_CFG1_VHF; + if (sr) + reg |= ONENAND_SYS_CFG1_SYNC_READ; + if (sw) + reg |= ONENAND_SYS_CFG1_SYNC_WRITE; + + write_reg(c, reg, ONENAND_REG_SYS_CFG1); + + return 0; +} + +static int omap2_onenand_get_freq(int ver) +{ + switch ((ver >> 4) & 0xf) { + case 0: + return 40; + case 1: + return 54; + case 2: + return 66; + case 3: + return 83; + case 4: + return 104; + } + + return -EINVAL; +} + static void wait_err(char *msg, int state, unsigned int ctrl, unsigned int intr) { printk(KERN_ERR "onenand_wait: %s! state %d ctrl 0x%04x intr 0x%04x\n", @@ -152,12 +209,12 @@ static int omap2_onenand_wait(struct mtd_info *mtd, int state) } reinit_completion(&c->irq_done); - result = gpio_get_value(c->gpio_irq); + result = gpiod_get_value(c->int_gpiod); if (result < 0) { ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS); intr = read_reg(c, ONENAND_REG_INTERRUPT); wait_err("gpio error", state, ctrl, intr); - return -EIO; + return result; } else if (result == 0) { int retry_cnt = 0; retry: @@ -431,8 +488,6 @@ out_copy: return 0; } -static struct platform_driver omap2_onenand_driver; - static void omap2_onenand_shutdown(struct platform_device *pdev) { struct omap2_onenand *c = dev_get_drvdata(&pdev->dev); @@ -446,105 +501,117 @@ static void omap2_onenand_shutdown(struct platform_device *pdev) static int omap2_onenand_probe(struct platform_device *pdev) { + u32 val; dma_cap_mask_t mask; - struct omap_onenand_platform_data *pdata; - struct omap2_onenand *c; - struct onenand_chip *this; - int r; + int freq, latency, r; struct resource *res; + struct omap2_onenand *c; + struct gpmc_onenand_info info; + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(dev, "error getting memory resource\n"); + return -EINVAL; + } - pdata = dev_get_platdata(&pdev->dev); - if (pdata == NULL) { - dev_err(&pdev->dev, "platform data missing\n"); - return -ENODEV; + r = of_property_read_u32(np, "reg", &val); + if (r) { + dev_err(dev, "reg not found in DT\n"); + return r; } - c = kzalloc(sizeof(struct omap2_onenand), GFP_KERNEL); + c = devm_kzalloc(dev, sizeof(struct omap2_onenand), GFP_KERNEL); if (!c) return -ENOMEM; init_completion(&c->irq_done); init_completion(&c->dma_done); - c->gpmc_cs = pdata->cs; - c->gpio_irq = pdata->gpio_irq; - if (pdata->dma_channel < 0) { - /* if -1, don't use DMA */ - c->gpio_irq = 0; - } - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (res == NULL) { - r = -EINVAL; - dev_err(&pdev->dev, "error getting memory resource\n"); - goto err_kfree; - } - + c->gpmc_cs = val; c->phys_base = res->start; - c->mem_size = resource_size(res); - - if (request_mem_region(c->phys_base, c->mem_size, - pdev->dev.driver->name) == NULL) { - dev_err(&pdev->dev, "Cannot reserve memory region at 0x%08lx, size: 0x%x\n", - c->phys_base, c->mem_size); - r = -EBUSY; - goto err_kfree; - } - c->onenand.base = ioremap(c->phys_base, c->mem_size); - if (c->onenand.base == NULL) { - r = -ENOMEM; - goto err_release_mem_region; - } - if (pdata->onenand_setup != NULL) { - r = pdata->onenand_setup(c->onenand.base, &c->freq); - if (r < 0) { - dev_err(&pdev->dev, "Onenand platform setup failed: " - "%d\n", r); - goto err_iounmap; - } - c->setup = pdata->onenand_setup; + c->onenand.base = devm_ioremap_resource(dev, res); + if (IS_ERR(c->onenand.base)) { + dev_err(dev, "Cannot reserve memory region at 0x%08x, size: 0x%x\n", + res->start, resource_size(res)); + return PTR_ERR(c->onenand.base); } - if (c->gpio_irq) { - if ((r = gpio_request(c->gpio_irq, "OneNAND irq")) < 0) { - dev_err(&pdev->dev, "Failed to request GPIO%d for " - "OneNAND\n", c->gpio_irq); - goto err_iounmap; - } - gpio_direction_input(c->gpio_irq); + c->int_gpiod = devm_gpiod_get_optional(dev, "int", GPIOD_IN); + if (IS_ERR(c->int_gpiod)) { + r = PTR_ERR(c->int_gpiod); + /* Just try again if this happens */ + if (r != -EPROBE_DEFER) + dev_err(dev, "error getting gpio: %d\n", r); + return r; + } - if ((r = request_irq(gpio_to_irq(c->gpio_irq), - omap2_onenand_interrupt, IRQF_TRIGGER_RISING, - pdev->dev.driver->name, c)) < 0) - goto err_release_gpio; + if (c->int_gpiod) { + r = devm_request_irq(dev, gpiod_to_irq(c->int_gpiod), + omap2_onenand_interrupt, + IRQF_TRIGGER_RISING, "onenand", c); + if (r) + return r; - this->wait = omap2_onenand_wait; + c->onenand.wait = omap2_onenand_wait; } dma_cap_zero(mask); dma_cap_set(DMA_MEMCPY, mask); c->dma_chan = dma_request_channel(mask, NULL, NULL); - - dev_info(&pdev->dev, "initializing on CS%d, phys base 0x%08lx, virtual " - "base %p, freq %d MHz, %s mode\n", c->gpmc_cs, c->phys_base, - c->onenand.base, c->freq, c->dma_chan ? "DMA" : "PIO"); + if (c->dma_chan) { + c->onenand.read_bufferram = omap2_onenand_read_bufferram; + c->onenand.write_bufferram = omap2_onenand_write_bufferram; + } c->pdev = pdev; c->mtd.priv = &c->onenand; + c->mtd.dev.parent = dev; + mtd_set_of_node(&c->mtd, dev->of_node); - c->mtd.dev.parent = &pdev->dev; - mtd_set_of_node(&c->mtd, pdata->of_node); - - this = &c->onenand; - if (c->dma_chan) { - this->read_bufferram = omap2_onenand_read_bufferram; - this->write_bufferram = omap2_onenand_write_bufferram; - } + dev_info(dev, "initializing on CS%d (0x%08lx), va %p, %s mode\n", + c->gpmc_cs, c->phys_base, c->onenand.base, + c->dma_chan ? "DMA" : "PIO"); if ((r = onenand_scan(&c->mtd, 1)) < 0) goto err_release_dma; + freq = omap2_onenand_get_freq(c->onenand.version_id); + if (freq > 0) { + switch (freq) { + case 104: + latency = 7; + break; + case 83: + latency = 6; + break; + case 66: + latency = 5; + break; + case 56: + latency = 4; + break; + default: /* 40 MHz or lower */ + latency = 3; + break; + } + + r = gpmc_omap_onenand_set_timings(dev, c->gpmc_cs, + freq, latency, &info); + if (r) + goto err_release_onenand; + + r = omap2_onenand_set_cfg(c, info.sync_read, info.sync_write, + latency, info.burst_len); + if (r) + goto err_release_onenand; + + if (info.sync_read || info.sync_write) + dev_info(dev, "optimized timings for %d MHz\n", freq); + } + r = mtd_device_register(&c->mtd, NULL, 0); if (r) goto err_release_onenand; @@ -558,17 +625,6 @@ err_release_onenand: err_release_dma: if (c->dma_chan) dma_release_channel(c->dma_chan); - if (c->gpio_irq) - free_irq(gpio_to_irq(c->gpio_irq), c); -err_release_gpio: - if (c->gpio_irq) - gpio_free(c->gpio_irq); -err_iounmap: - iounmap(c->onenand.base); -err_release_mem_region: - release_mem_region(c->phys_base, c->mem_size); -err_kfree: - kfree(c); return r; } @@ -581,23 +637,23 @@ static int omap2_onenand_remove(struct platform_device *pdev) if (c->dma_chan) dma_release_channel(c->dma_chan); omap2_onenand_shutdown(pdev); - if (c->gpio_irq) { - free_irq(gpio_to_irq(c->gpio_irq), c); - gpio_free(c->gpio_irq); - } - iounmap(c->onenand.base); - release_mem_region(c->phys_base, c->mem_size); - kfree(c); return 0; } +static const struct of_device_id omap2_onenand_id_table[] = { + { .compatible = "ti,omap2-onenand", }, + {}, +}; +MODULE_DEVICE_TABLE(of, omap2_onenand_id_table); + static struct platform_driver omap2_onenand_driver = { .probe = omap2_onenand_probe, .remove = omap2_onenand_remove, .shutdown = omap2_onenand_shutdown, .driver = { .name = DRIVER_NAME, + .of_match_table = omap2_onenand_id_table, }, }; diff --git a/include/linux/omap-gpmc.h b/include/linux/omap-gpmc.h index edfa280c3d56..053feb41510a 100644 --- a/include/linux/omap-gpmc.h +++ b/include/linux/omap-gpmc.h @@ -25,15 +25,43 @@ struct gpmc_nand_ops { struct gpmc_nand_regs; +struct gpmc_onenand_info { + bool sync_read; + bool sync_write; + int burst_len; +}; + #if IS_ENABLED(CONFIG_OMAP_GPMC) struct gpmc_nand_ops *gpmc_omap_get_nand_ops(struct gpmc_nand_regs *regs, int cs); +/** + * gpmc_omap_onenand_set_timings - set optimized sync timings. + * @cs: Chip Select Region + * @freq: Chip frequency + * @latency: Burst latency cycle count + * @info: Structure describing parameters used + * + * Sets optimized timings for the @cs region based on @freq and @latency. + * Updates the @info structure based on the GPMC settings. + */ +int gpmc_omap_onenand_set_timings(struct device *dev, int cs, int freq, + int latency, + struct gpmc_onenand_info *info); + #else static inline struct gpmc_nand_ops *gpmc_omap_get_nand_ops(struct gpmc_nand_regs *regs, int cs) { return NULL; } + +static inline +int gpmc_omap_onenand_set_timings(struct device *dev, int cs, int freq, + int latency, + struct gpmc_onenand_info *info) +{ + return -EINVAL; +} #endif /* CONFIG_OMAP_GPMC */ extern int gpmc_calc_timings(struct gpmc_timings *gpmc_t, -- cgit v1.2.3 From 2514830b8b8ca966fae35103070984c2e847b2b9 Mon Sep 17 00:00:00 2001 From: Ladislav Michl Date: Fri, 12 Jan 2018 14:18:00 +0100 Subject: ARM: OMAP2+: Remove gpmc-onenand As OneNAND driver is now using devicetree gpmc-onenand and its platform data is unused and can be removed. Signed-off-by: Ladislav Michl Reviewed-by: Peter Ujfalusi Acked-by: Roger Quadros Acked-by: Tony Lindgren Tested-by: Tony Lindgren Tested-by: Aaro Koskinen Signed-off-by: Boris Brezillon --- arch/arm/mach-omap2/Makefile | 3 - arch/arm/mach-omap2/gpmc-onenand.c | 409 ------------------------ include/linux/platform_data/mtd-onenand-omap2.h | 34 -- 3 files changed, 446 deletions(-) delete mode 100644 arch/arm/mach-omap2/gpmc-onenand.c delete mode 100644 include/linux/platform_data/mtd-onenand-omap2.h diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 2f722a805948..c15bbcad5f67 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -232,6 +232,3 @@ obj-y += $(omap-hsmmc-m) $(omap-hsmmc-y) obj-y += omap_phy_internal.o obj-$(CONFIG_MACH_OMAP2_TUSB6010) += usb-tusb6010.o - -onenand-$(CONFIG_MTD_ONENAND_OMAP2) := gpmc-onenand.o -obj-y += $(onenand-m) $(onenand-y) diff --git a/arch/arm/mach-omap2/gpmc-onenand.c b/arch/arm/mach-omap2/gpmc-onenand.c deleted file mode 100644 index 2944af820558..000000000000 --- a/arch/arm/mach-omap2/gpmc-onenand.c +++ /dev/null @@ -1,409 +0,0 @@ -/* - * linux/arch/arm/mach-omap2/gpmc-onenand.c - * - * Copyright (C) 2006 - 2009 Nokia Corporation - * Contacts: Juha Yrjola - * Tony Lindgren - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include - -#include "soc.h" - -#define ONENAND_IO_SIZE SZ_128K - -#define ONENAND_FLAG_SYNCREAD (1 << 0) -#define ONENAND_FLAG_SYNCWRITE (1 << 1) -#define ONENAND_FLAG_HF (1 << 2) -#define ONENAND_FLAG_VHF (1 << 3) - -static unsigned onenand_flags; -static unsigned latency; - -static struct omap_onenand_platform_data *gpmc_onenand_data; - -static struct resource gpmc_onenand_resource = { - .flags = IORESOURCE_MEM, -}; - -static struct platform_device gpmc_onenand_device = { - .name = "omap2-onenand", - .id = -1, - .num_resources = 1, - .resource = &gpmc_onenand_resource, -}; - -static struct gpmc_settings onenand_async = { - .device_width = GPMC_DEVWIDTH_16BIT, - .mux_add_data = GPMC_MUX_AD, -}; - -static struct gpmc_settings onenand_sync = { - .burst_read = true, - .burst_wrap = true, - .burst_len = GPMC_BURST_16, - .device_width = GPMC_DEVWIDTH_16BIT, - .mux_add_data = GPMC_MUX_AD, - .wait_pin = 0, -}; - -static void omap2_onenand_calc_async_timings(struct gpmc_timings *t) -{ - struct gpmc_device_timings dev_t; - const int t_cer = 15; - const int t_avdp = 12; - const int t_aavdh = 7; - const int t_ce = 76; - const int t_aa = 76; - const int t_oe = 20; - const int t_cez = 20; /* max of t_cez, t_oez */ - const int t_wpl = 40; - const int t_wph = 30; - - memset(&dev_t, 0, sizeof(dev_t)); - - dev_t.t_avdp_r = max_t(int, t_avdp, t_cer) * 1000; - dev_t.t_avdp_w = dev_t.t_avdp_r; - dev_t.t_aavdh = t_aavdh * 1000; - dev_t.t_aa = t_aa * 1000; - dev_t.t_ce = t_ce * 1000; - dev_t.t_oe = t_oe * 1000; - dev_t.t_cez_r = t_cez * 1000; - dev_t.t_cez_w = dev_t.t_cez_r; - dev_t.t_wpl = t_wpl * 1000; - dev_t.t_wph = t_wph * 1000; - - gpmc_calc_timings(t, &onenand_async, &dev_t); -} - -static void omap2_onenand_set_async_mode(void __iomem *onenand_base) -{ - u32 reg; - - /* Ensure sync read and sync write are disabled */ - reg = readw(onenand_base + ONENAND_REG_SYS_CFG1); - reg &= ~ONENAND_SYS_CFG1_SYNC_READ & ~ONENAND_SYS_CFG1_SYNC_WRITE; - writew(reg, onenand_base + ONENAND_REG_SYS_CFG1); -} - -static void set_onenand_cfg(void __iomem *onenand_base) -{ - u32 reg = ONENAND_SYS_CFG1_RDY | ONENAND_SYS_CFG1_INT; - - reg |= (latency << ONENAND_SYS_CFG1_BRL_SHIFT) | - ONENAND_SYS_CFG1_BL_16; - if (onenand_flags & ONENAND_FLAG_SYNCREAD) - reg |= ONENAND_SYS_CFG1_SYNC_READ; - else - reg &= ~ONENAND_SYS_CFG1_SYNC_READ; - if (onenand_flags & ONENAND_FLAG_SYNCWRITE) - reg |= ONENAND_SYS_CFG1_SYNC_WRITE; - else - reg &= ~ONENAND_SYS_CFG1_SYNC_WRITE; - if (onenand_flags & ONENAND_FLAG_HF) - reg |= ONENAND_SYS_CFG1_HF; - else - reg &= ~ONENAND_SYS_CFG1_HF; - if (onenand_flags & ONENAND_FLAG_VHF) - reg |= ONENAND_SYS_CFG1_VHF; - else - reg &= ~ONENAND_SYS_CFG1_VHF; - - writew(reg, onenand_base + ONENAND_REG_SYS_CFG1); -} - -static int omap2_onenand_get_freq(struct omap_onenand_platform_data *cfg, - void __iomem *onenand_base) -{ - u16 ver = readw(onenand_base + ONENAND_REG_VERSION_ID); - int freq; - - switch ((ver >> 4) & 0xf) { - case 0: - freq = 40; - break; - case 1: - freq = 54; - break; - case 2: - freq = 66; - break; - case 3: - freq = 83; - break; - case 4: - freq = 104; - break; - default: - pr_err("onenand rate not detected, bad GPMC async timings?\n"); - freq = 0; - } - - return freq; -} - -static void omap2_onenand_calc_sync_timings(struct gpmc_timings *t, - unsigned int flags, - int freq) -{ - struct gpmc_device_timings dev_t; - const int t_cer = 15; - const int t_avdp = 12; - const int t_cez = 20; /* max of t_cez, t_oez */ - const int t_wpl = 40; - const int t_wph = 30; - int min_gpmc_clk_period, t_ces, t_avds, t_avdh, t_ach, t_aavdh, t_rdyo; - int div, gpmc_clk_ns; - - if (flags & ONENAND_SYNC_READ) - onenand_flags = ONENAND_FLAG_SYNCREAD; - else if (flags & ONENAND_SYNC_READWRITE) - onenand_flags = ONENAND_FLAG_SYNCREAD | ONENAND_FLAG_SYNCWRITE; - - switch (freq) { - case 104: - min_gpmc_clk_period = 9600; /* 104 MHz */ - t_ces = 3; - t_avds = 4; - t_avdh = 2; - t_ach = 3; - t_aavdh = 6; - t_rdyo = 6; - break; - case 83: - min_gpmc_clk_period = 12000; /* 83 MHz */ - t_ces = 5; - t_avds = 4; - t_avdh = 2; - t_ach = 6; - t_aavdh = 6; - t_rdyo = 9; - break; - case 66: - min_gpmc_clk_period = 15000; /* 66 MHz */ - t_ces = 6; - t_avds = 5; - t_avdh = 2; - t_ach = 6; - t_aavdh = 6; - t_rdyo = 11; - break; - default: - min_gpmc_clk_period = 18500; /* 54 MHz */ - t_ces = 7; - t_avds = 7; - t_avdh = 7; - t_ach = 9; - t_aavdh = 7; - t_rdyo = 15; - onenand_flags &= ~ONENAND_FLAG_SYNCWRITE; - break; - } - - div = gpmc_calc_divider(min_gpmc_clk_period); - gpmc_clk_ns = gpmc_ticks_to_ns(div); - if (gpmc_clk_ns < 15) /* >66MHz */ - onenand_flags |= ONENAND_FLAG_HF; - else - onenand_flags &= ~ONENAND_FLAG_HF; - if (gpmc_clk_ns < 12) /* >83MHz */ - onenand_flags |= ONENAND_FLAG_VHF; - else - onenand_flags &= ~ONENAND_FLAG_VHF; - if (onenand_flags & ONENAND_FLAG_VHF) - latency = 8; - else if (onenand_flags & ONENAND_FLAG_HF) - latency = 6; - else if (gpmc_clk_ns >= 25) /* 40 MHz*/ - latency = 3; - else - latency = 4; - - /* Set synchronous read timings */ - memset(&dev_t, 0, sizeof(dev_t)); - - if (onenand_flags & ONENAND_FLAG_SYNCREAD) - onenand_sync.sync_read = true; - if (onenand_flags & ONENAND_FLAG_SYNCWRITE) { - onenand_sync.sync_write = true; - onenand_sync.burst_write = true; - } else { - dev_t.t_avdp_w = max(t_avdp, t_cer) * 1000; - dev_t.t_wpl = t_wpl * 1000; - dev_t.t_wph = t_wph * 1000; - dev_t.t_aavdh = t_aavdh * 1000; - } - dev_t.ce_xdelay = true; - dev_t.avd_xdelay = true; - dev_t.oe_xdelay = true; - dev_t.we_xdelay = true; - dev_t.clk = min_gpmc_clk_period; - dev_t.t_bacc = dev_t.clk; - dev_t.t_ces = t_ces * 1000; - dev_t.t_avds = t_avds * 1000; - dev_t.t_avdh = t_avdh * 1000; - dev_t.t_ach = t_ach * 1000; - dev_t.cyc_iaa = (latency + 1); - dev_t.t_cez_r = t_cez * 1000; - dev_t.t_cez_w = dev_t.t_cez_r; - dev_t.cyc_aavdh_oe = 1; - dev_t.t_rdyo = t_rdyo * 1000 + min_gpmc_clk_period; - - gpmc_calc_timings(t, &onenand_sync, &dev_t); -} - -static int omap2_onenand_setup_async(void __iomem *onenand_base) -{ - struct gpmc_timings t; - int ret; - - /* - * Note that we need to keep sync_write set for the call to - * omap2_onenand_set_async_mode() to work to detect the onenand - * supported clock rate for the sync timings. - */ - if (gpmc_onenand_data->of_node) { - gpmc_read_settings_dt(gpmc_onenand_data->of_node, - &onenand_async); - if (onenand_async.sync_read || onenand_async.sync_write) { - if (onenand_async.sync_write) - gpmc_onenand_data->flags |= - ONENAND_SYNC_READWRITE; - else - gpmc_onenand_data->flags |= ONENAND_SYNC_READ; - onenand_async.sync_read = false; - } - } - - onenand_async.sync_write = true; - omap2_onenand_calc_async_timings(&t); - - ret = gpmc_cs_program_settings(gpmc_onenand_data->cs, &onenand_async); - if (ret < 0) - return ret; - - ret = gpmc_cs_set_timings(gpmc_onenand_data->cs, &t, &onenand_async); - if (ret < 0) - return ret; - - omap2_onenand_set_async_mode(onenand_base); - - return 0; -} - -static int omap2_onenand_setup_sync(void __iomem *onenand_base, int *freq_ptr) -{ - int ret, freq = *freq_ptr; - struct gpmc_timings t; - - if (!freq) { - /* Very first call freq is not known */ - freq = omap2_onenand_get_freq(gpmc_onenand_data, onenand_base); - if (!freq) - return -ENODEV; - set_onenand_cfg(onenand_base); - } - - if (gpmc_onenand_data->of_node) { - gpmc_read_settings_dt(gpmc_onenand_data->of_node, - &onenand_sync); - } else { - /* - * FIXME: Appears to be legacy code from initial ONENAND commit. - * Unclear what boards this is for and if this can be removed. - */ - if (!cpu_is_omap34xx()) - onenand_sync.wait_on_read = true; - } - - omap2_onenand_calc_sync_timings(&t, gpmc_onenand_data->flags, freq); - - ret = gpmc_cs_program_settings(gpmc_onenand_data->cs, &onenand_sync); - if (ret < 0) - return ret; - - ret = gpmc_cs_set_timings(gpmc_onenand_data->cs, &t, &onenand_sync); - if (ret < 0) - return ret; - - set_onenand_cfg(onenand_base); - - *freq_ptr = freq; - - return 0; -} - -static int gpmc_onenand_setup(void __iomem *onenand_base, int *freq_ptr) -{ - struct device *dev = &gpmc_onenand_device.dev; - unsigned l = ONENAND_SYNC_READ | ONENAND_SYNC_READWRITE; - int ret; - - ret = omap2_onenand_setup_async(onenand_base); - if (ret) { - dev_err(dev, "unable to set to async mode\n"); - return ret; - } - - if (!(gpmc_onenand_data->flags & l)) - return 0; - - ret = omap2_onenand_setup_sync(onenand_base, freq_ptr); - if (ret) - dev_err(dev, "unable to set to sync mode\n"); - return ret; -} - -int gpmc_onenand_init(struct omap_onenand_platform_data *_onenand_data) -{ - int err; - struct device *dev = &gpmc_onenand_device.dev; - - gpmc_onenand_data = _onenand_data; - gpmc_onenand_data->onenand_setup = gpmc_onenand_setup; - gpmc_onenand_device.dev.platform_data = gpmc_onenand_data; - - if (cpu_is_omap24xx() && - (gpmc_onenand_data->flags & ONENAND_SYNC_READWRITE)) { - dev_warn(dev, "OneNAND using only SYNC_READ on 24xx\n"); - gpmc_onenand_data->flags &= ~ONENAND_SYNC_READWRITE; - gpmc_onenand_data->flags |= ONENAND_SYNC_READ; - } - - if (cpu_is_omap34xx()) - gpmc_onenand_data->flags |= ONENAND_IN_OMAP34XX; - else - gpmc_onenand_data->flags &= ~ONENAND_IN_OMAP34XX; - - err = gpmc_cs_request(gpmc_onenand_data->cs, ONENAND_IO_SIZE, - (unsigned long *)&gpmc_onenand_resource.start); - if (err < 0) { - dev_err(dev, "Cannot request GPMC CS %d, error %d\n", - gpmc_onenand_data->cs, err); - return err; - } - - gpmc_onenand_resource.end = gpmc_onenand_resource.start + - ONENAND_IO_SIZE - 1; - - err = platform_device_register(&gpmc_onenand_device); - if (err) { - dev_err(dev, "Unable to register OneNAND device\n"); - gpmc_cs_free(gpmc_onenand_data->cs); - } - - return err; -} diff --git a/include/linux/platform_data/mtd-onenand-omap2.h b/include/linux/platform_data/mtd-onenand-omap2.h deleted file mode 100644 index 56ff0e6f5ad1..000000000000 --- a/include/linux/platform_data/mtd-onenand-omap2.h +++ /dev/null @@ -1,34 +0,0 @@ -/* - * Copyright (C) 2006 Nokia Corporation - * Author: Juha Yrjola - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#ifndef __MTD_ONENAND_OMAP2_H -#define __MTD_ONENAND_OMAP2_H - -#include -#include - -#define ONENAND_SYNC_READ (1 << 0) -#define ONENAND_SYNC_READWRITE (1 << 1) -#define ONENAND_IN_OMAP34XX (1 << 2) - -struct omap_onenand_platform_data { - int cs; - int gpio_irq; - struct mtd_partition *parts; - int nr_parts; - int (*onenand_setup)(void __iomem *, int *freq_ptr); - int dma_channel; - u8 flags; - u8 regulator_can_sleep; - u8 skip_initial_unlocking; - - /* for passing the partitions */ - struct device_node *of_node; -}; -#endif -- cgit v1.2.3 From b4525db6f0c6dc02ad2bde08a3bcdcf0ad7891d4 Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Sat, 13 Jan 2018 11:54:10 +0100 Subject: MAINTAINERS: Add entry for Marvell NAND controller driver Add entry for Marvell NAND controller driver and its bindings which will soon replace the old driver pxa3xx_nand.c. Signed-off-by: Miquel Raynal Signed-off-by: Boris Brezillon --- MAINTAINERS | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index 37ee5ae4bae2..81c8c5162144 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -8402,6 +8402,13 @@ L: linux-wireless@vger.kernel.org S: Odd Fixes F: drivers/net/wireless/marvell/mwl8k.c +MARVELL NAND CONTROLLER DRIVER +M: Miquel Raynal +L: linux-mtd@lists.infradead.org +S: Maintained +F: drivers/mtd/nand/marvell_nand.c +F: Documentation/devicetree/bindings/mtd/marvell-nand.txt + MARVELL SOC MMC/SD/SDIO CONTROLLER DRIVER M: Nicolas Pitre S: Odd Fixes -- cgit v1.2.3 From 6837befde3a6b42a36c894a4f86bafdc6db82534 Mon Sep 17 00:00:00 2001 From: Christophe JAILLET Date: Sat, 13 Jan 2018 17:56:16 +0100 Subject: mtd: onenand: samsung: remove incorrect __iomem annotation 'page_buf' and 'oob_buf' are allocated with 'devm_kzalloc()' and should not have __iomem decoration. Remove these decorations and some useless casting. Signed-off-by: Christophe JAILLET Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/samsung.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/mtd/onenand/samsung.c b/drivers/mtd/onenand/samsung.c index dfdfb478ba35..2e9d076e445a 100644 --- a/drivers/mtd/onenand/samsung.c +++ b/drivers/mtd/onenand/samsung.c @@ -129,8 +129,8 @@ struct s3c_onenand { void __iomem *base; void __iomem *ahb_addr; int bootram_command; - void __iomem *page_buf; - void __iomem *oob_buf; + void *page_buf; + void *oob_buf; unsigned int (*mem_addr)(int fba, int fpa, int fsa); unsigned int (*cmd_map)(unsigned int type, unsigned int val); void __iomem *dma_addr; @@ -408,8 +408,8 @@ static int s3c_onenand_command(struct mtd_info *mtd, int cmd, loff_t addr, /* * Emulate Two BufferRAMs and access with 4 bytes pointer */ - m = (unsigned int *) onenand->page_buf; - s = (unsigned int *) onenand->oob_buf; + m = onenand->page_buf; + s = onenand->oob_buf; if (index) { m += (this->writesize >> 2); @@ -481,11 +481,11 @@ static unsigned char *s3c_get_bufferram(struct mtd_info *mtd, int area) unsigned char *p; if (area == ONENAND_DATARAM) { - p = (unsigned char *) onenand->page_buf; + p = onenand->page_buf; if (index == 1) p += this->writesize; } else { - p = (unsigned char *) onenand->oob_buf; + p = onenand->oob_buf; if (index == 1) p += mtd->oobsize; } -- cgit v1.2.3 From 82cea533aed44c1b8553fe782e1bc5e1262bd71a Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Tue, 16 Jan 2018 08:43:40 +0100 Subject: mtd: onenand: omap2: print resource using %pR format string The omap2 onenand driver is now available for compile-testing, which uncovers a warning in configurations that have a 64-bit resource_size_t: drivers/mtd/onenand/omap2.c: In function 'omap2_onenand_probe': drivers/mtd/onenand/omap2.c:536:54: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t {aka long long unsigned int}' [-Werror=format=] dev_err(dev, "Cannot reserve memory region at 0x%08x, size: 0x%x\n", drivers/mtd/onenand/omap2.c:536:66: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t {aka long long unsigned int}' [-Werror=format=] Changing the format string to the special %pR simplifies the code and lets it do the right thing in that configuration, while avoiding the warning. Fixes: a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT") Signed-off-by: Arnd Bergmann Reviewed-by: Sebastian Reichel Reviewed-by: Peter Ujfalusi Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/omap2.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index 2ce73fb6da1c..a4a2159bcfb7 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -533,8 +533,7 @@ static int omap2_onenand_probe(struct platform_device *pdev) c->onenand.base = devm_ioremap_resource(dev, res); if (IS_ERR(c->onenand.base)) { - dev_err(dev, "Cannot reserve memory region at 0x%08x, size: 0x%x\n", - res->start, resource_size(res)); + dev_err(dev, "Cannot reserve memory region %pR\n", res); return PTR_ERR(c->onenand.base); } -- cgit v1.2.3 From e6b90db83f8b33735fe5a008ff171f69527a5305 Mon Sep 17 00:00:00 2001 From: Wei Yongjun Date: Wed, 17 Jan 2018 11:25:33 +0000 Subject: mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe() There is a error message within devm_ioremap_resource already, so remove the dev_err call to avoid redundant error message. Signed-off-by: Wei Yongjun Signed-off-by: Boris Brezillon --- drivers/mtd/onenand/omap2.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c index a4a2159bcfb7..87c34f607a75 100644 --- a/drivers/mtd/onenand/omap2.c +++ b/drivers/mtd/onenand/omap2.c @@ -532,10 +532,8 @@ static int omap2_onenand_probe(struct platform_device *pdev) c->phys_base = res->start; c->onenand.base = devm_ioremap_resource(dev, res); - if (IS_ERR(c->onenand.base)) { - dev_err(dev, "Cannot reserve memory region %pR\n", res); + if (IS_ERR(c->onenand.base)) return PTR_ERR(c->onenand.base); - } c->int_gpiod = devm_gpiod_get_optional(dev, "int", GPIOD_IN); if (IS_ERR(c->int_gpiod)) { -- cgit v1.2.3 From a76497dc49518bc162ebc8ee4f139a075b9f9ad0 Mon Sep 17 00:00:00 2001 From: Colin Ian King Date: Fri, 19 Jan 2018 07:55:31 +0000 Subject: mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed" Trivial fix to spelling mistakes in dev_err error message text. Signed-off-by: Colin Ian King Acked-by: Miquel Raynal Signed-off-by: Boris Brezillon --- drivers/mtd/nand/marvell_nand.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mtd/nand/marvell_nand.c b/drivers/mtd/nand/marvell_nand.c index b8fec6093b75..4bd53b360277 100644 --- a/drivers/mtd/nand/marvell_nand.c +++ b/drivers/mtd/nand/marvell_nand.c @@ -517,7 +517,7 @@ static int marvell_nfc_prepare_cmd(struct nand_chip *chip) /* Poll ND_RUN and clear NDSR before issuing any command */ ret = marvell_nfc_wait_ndrun(chip); if (ret) { - dev_err(nfc->dev, "Last operation did not suceed\n"); + dev_err(nfc->dev, "Last operation did not succeed\n"); return ret; } -- cgit v1.2.3 From e06a181b5dad6b1904e09e62c924868d7cfeacb6 Mon Sep 17 00:00:00 2001 From: Colin Ian King Date: Fri, 19 Jan 2018 07:59:54 +0000 Subject: mtd: nand: marvell: remove redundant variable 'oob_len' Variable oob_len is assigned and never read, hence it is redundant and can be removed. Cleans up clang warnings: drivers/mtd/nand/marvell_nand.c:1356:6: warning: Value stored to 'oob_len' during its initialization is never read drivers/mtd/nand/marvell_nand.c:1369:4: warning: Value stored to 'oob_len' is never read Signed-off-by: Colin Ian King Acked-by: Miquel Raynal Signed-off-by: Boris Brezillon --- drivers/mtd/nand/marvell_nand.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/drivers/mtd/nand/marvell_nand.c b/drivers/mtd/nand/marvell_nand.c index 4bd53b360277..f15ab37edf4e 100644 --- a/drivers/mtd/nand/marvell_nand.c +++ b/drivers/mtd/nand/marvell_nand.c @@ -1353,7 +1353,6 @@ static int marvell_nfc_hw_ecc_bch_write_page_raw(struct mtd_info *mtd, int data_len = lt->data_bytes; int spare_len = lt->spare_bytes; int ecc_len = lt->ecc_bytes; - int oob_len = spare_len + ecc_len; int spare_offset = 0; int ecc_offset = (lt->full_chunk_cnt * lt->spare_bytes) + lt->last_spare_bytes; @@ -1366,7 +1365,6 @@ static int marvell_nfc_hw_ecc_bch_write_page_raw(struct mtd_info *mtd, data_len = lt->last_data_bytes; spare_len = lt->last_spare_bytes; ecc_len = lt->last_ecc_bytes; - oob_len = spare_len + ecc_len; } /* Point to the column of the next chunk */ -- cgit v1.2.3 From c495a9275eeca0bbc9358de7200e58184e864aeb Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Fri, 19 Jan 2018 18:39:01 +0100 Subject: mtd: nand: marvell: Fix missing memory allocation modifier The function marvell_nfc_init_dma() allocates a DMA buffer without the GFP_KERNEL modifier, that triggers this warning: "marvell_nfc_init_dma() error: no modifiers for allocation." Fix this by using (GFP_KERNEL | GFP_DMA) instead of only GFP_DMA as the probe happens in non-interrupt context. Fixes: 02f26ecf8c77 ("mtd: nand: add reworked Marvell NAND controller driver") Reported-by: Dan Carpenter Signed-off-by: Miquel Raynal Signed-off-by: Boris Brezillon --- drivers/mtd/nand/marvell_nand.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mtd/nand/marvell_nand.c b/drivers/mtd/nand/marvell_nand.c index f15ab37edf4e..2196f2a233d6 100644 --- a/drivers/mtd/nand/marvell_nand.c +++ b/drivers/mtd/nand/marvell_nand.c @@ -2649,7 +2649,7 @@ static int marvell_nfc_init_dma(struct marvell_nfc *nfc) * for DMA transfers and then copy the desired amount of data to * the provided buffer. */ - nfc->dma_buf = kmalloc(MAX_CHUNK_SIZE, GFP_DMA); + nfc->dma_buf = kmalloc(MAX_CHUNK_SIZE, GFP_KERNEL | GFP_DMA); if (!nfc->dma_buf) return -ENOMEM; -- cgit v1.2.3 From c1a72e2dbb4abb90bd408480d7c48ba40cb799ce Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Fri, 19 Jan 2018 19:11:27 +0100 Subject: mtd: nand: Fix build issues due to an anonymous union GCC-4.4.4 raises errors when assigning a parameter in an anonymous union, leading to this kind of failure: drivers/mtd/nand/marvell_nand.c:1936: warning: missing braces around initializer warning: (near initialization for '(anonymous)[1].') error: unknown field 'data' specified in initializer error: unknown field 'addr' specified in initializer Work around the situation by naming these unions. Fixes: 8878b126df76 ("mtd: nand: add ->exec_op() implementation") Reported-by: Andrew Morton Signed-off-by: Miquel Raynal Tested-by: Andrew Morton Signed-off-by: Boris Brezillon --- drivers/mtd/nand/nand_base.c | 13 +++++++------ include/linux/mtd/rawnand.h | 8 ++++---- 2 files changed, 11 insertions(+), 10 deletions(-) diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 3ff77bef9739..66b67014508f 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -2335,23 +2335,24 @@ nand_op_parser_must_split_instr(const struct nand_op_parser_pattern_elem *pat, { switch (pat->type) { case NAND_OP_ADDR_INSTR: - if (!pat->addr.maxcycles) + if (!pat->ctx.addr.maxcycles) break; if (instr->ctx.addr.naddrs - *start_offset > - pat->addr.maxcycles) { - *start_offset += pat->addr.maxcycles; + pat->ctx.addr.maxcycles) { + *start_offset += pat->ctx.addr.maxcycles; return true; } break; case NAND_OP_DATA_IN_INSTR: case NAND_OP_DATA_OUT_INSTR: - if (!pat->data.maxlen) + if (!pat->ctx.data.maxlen) break; - if (instr->ctx.data.len - *start_offset > pat->data.maxlen) { - *start_offset += pat->data.maxlen; + if (instr->ctx.data.len - *start_offset > + pat->ctx.data.maxlen) { + *start_offset += pat->ctx.data.maxlen; return true; } break; diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h index 469dc724f5df..56c5570aadbe 100644 --- a/include/linux/mtd/rawnand.h +++ b/include/linux/mtd/rawnand.h @@ -962,7 +962,7 @@ struct nand_op_parser_pattern_elem { union { struct nand_op_parser_addr_constraints addr; struct nand_op_parser_data_constraints data; - }; + } ctx; }; #define NAND_OP_PARSER_PAT_CMD_ELEM(_opt) \ @@ -975,21 +975,21 @@ struct nand_op_parser_pattern_elem { { \ .type = NAND_OP_ADDR_INSTR, \ .optional = _opt, \ - .addr.maxcycles = _maxcycles, \ + .ctx.addr.maxcycles = _maxcycles, \ } #define NAND_OP_PARSER_PAT_DATA_IN_ELEM(_opt, _maxlen) \ { \ .type = NAND_OP_DATA_IN_INSTR, \ .optional = _opt, \ - .data.maxlen = _maxlen, \ + .ctx.data.maxlen = _maxlen, \ } #define NAND_OP_PARSER_PAT_DATA_OUT_ELEM(_opt, _maxlen) \ { \ .type = NAND_OP_DATA_OUT_INSTR, \ .optional = _opt, \ - .data.maxlen = _maxlen, \ + .ctx.data.maxlen = _maxlen, \ } #define NAND_OP_PARSER_PAT_WAITRDY_ELEM(_opt) \ -- cgit v1.2.3 From 4c7e95b1b3286a2ba704790018a35510344958f2 Mon Sep 17 00:00:00 2001 From: Boris Brezillon Date: Tue, 23 Jan 2018 11:13:17 +0100 Subject: mtd: nand: gpmi: Fix subpage reads Commit 25f815f66a14 ("mtd: nand: force drivers to explicitly send READ/PROG commands") added a call to nand_read_page_op() in gpmi_ecc_read_page(), which means this function now sends a READ0 command and place the data pointer at the beginning of the page. This logic is breaking gpmi_ecc_read_subpage() which was calling gpmi_ecc_read_page() and expected it to only retrieve the data without sending the READ0 command. Create a gpmi_ecc_read_page_data() helper which only does the data retrieval and ECC correction steps and implement gpmi_ecc_read_page() as a wrapper that calls nand_read_page_op()+gpmi_ecc_read_page_data(). This way, gpmi_ecc_read_subpage() can call gpmi_ecc_read_page_data() which restores the logic we had before commit 25f815f66a14 ("mtd: nand: force drivers to explicitly send READ/PROG commands"). Fixes: 25f815f66a14 ("mtd: nand: force drivers to explicitly send READ/PROG commands") Signed-off-by: Boris Brezillon Reviewed-by: Miquel Raynal Acked-by: Han Xu --- drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 18 +++++++++++++----- 1 file changed, 13 insertions(+), 5 deletions(-) diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c index b51db8c85405..ab9a0a2ed3b2 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c @@ -1029,11 +1029,13 @@ static void block_mark_swapping(struct gpmi_nand_data *this, p[1] = (p[1] & mask) | (from_oob >> (8 - bit)); } -static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip, - uint8_t *buf, int oob_required, int page) +static int gpmi_ecc_read_page_data(struct nand_chip *chip, + uint8_t *buf, int oob_required, + int page) { struct gpmi_nand_data *this = nand_get_controller_data(chip); struct bch_geometry *nfc_geo = &this->bch_geometry; + struct mtd_info *mtd = nand_to_mtd(chip); void *payload_virt; dma_addr_t payload_phys; void *auxiliary_virt; @@ -1043,8 +1045,6 @@ static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip, unsigned int max_bitflips = 0; int ret; - nand_read_page_op(chip, page, 0, NULL, 0); - dev_dbg(this->dev, "page number is : %d\n", page); ret = read_page_prepare(this, buf, nfc_geo->payload_size, this->payload_virt, this->payload_phys, @@ -1178,6 +1178,14 @@ static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip, return max_bitflips; } +static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + nand_read_page_op(chip, page, 0, NULL, 0); + + return gpmi_ecc_read_page_data(chip, buf, oob_required, page); +} + /* Fake a virtual small page for the subpage read */ static int gpmi_ecc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, uint32_t offs, uint32_t len, uint8_t *buf, int page) @@ -1256,7 +1264,7 @@ static int gpmi_ecc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, /* Read the subpage now */ this->swap_block_mark = false; - max_bitflips = gpmi_ecc_read_page(mtd, chip, buf, 0, page); + max_bitflips = gpmi_ecc_read_page_data(chip, buf, 0, page); /* Restore */ writel(r1_old, bch_regs + HW_BCH_FLASH0LAYOUT0); -- cgit v1.2.3 From f4c6cd1a7f2275d5bc0e494b21fff26f8dde80f0 Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Wed, 24 Jan 2018 23:49:31 +0100 Subject: mtd: nand: sunxi: Fix ECC strength choice When the requested ECC strength does not exactly match the strengths supported by the ECC engine, the driver is selecting the closest strength meeting the 'selected_strength > requested_strength' constraint. Fix the fact that, in this particular case, ecc->strength value was not updated to match the 'selected_strength'. For instance, one can encounter this issue when no ECC requirement is filled in the device tree while the NAND chip minimum requirement is not a strength/step_size combo natively supported by the ECC engine. Fixes: 1fef62c1423b ("mtd: nand: add sunxi NAND flash controller support") Cc: Suggested-by: Boris Brezillon Signed-off-by: Miquel Raynal Signed-off-by: Boris Brezillon --- drivers/mtd/nand/sunxi_nand.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/drivers/mtd/nand/sunxi_nand.c b/drivers/mtd/nand/sunxi_nand.c index 2275fbedfb2a..f5a55c63935c 100644 --- a/drivers/mtd/nand/sunxi_nand.c +++ b/drivers/mtd/nand/sunxi_nand.c @@ -1858,8 +1858,14 @@ static int sunxi_nand_hw_common_ecc_ctrl_init(struct mtd_info *mtd, /* Add ECC info retrieval from DT */ for (i = 0; i < ARRAY_SIZE(strengths); i++) { - if (ecc->strength <= strengths[i]) + if (ecc->strength <= strengths[i]) { + /* + * Update ecc->strength value with the actual strength + * that will be used by the ECC engine. + */ + ecc->strength = strengths[i]; break; + } } if (i >= ARRAY_SIZE(strengths)) { -- cgit v1.2.3