From 07c121149cb30405b37ceae3cd29e5b6b6e65cc0 Mon Sep 17 00:00:00 2001 From: Marek Belisko Date: Thu, 15 Nov 2012 22:51:56 +0100 Subject: Documentation: Move common leds properties description to separate file. There are several drivers that use LEDs and depend on exactly the same device tree binding. However, the binding documentation has simply been cut-and-paste into each of the binding documents. Rather than continue to duplicate it, this patch adds a common led binding document that all can reference. Signed-off-by: Marek Belisko Reviewed-by: Stephen Warren Signed-off-by: Grant Likely --- Documentation/devicetree/bindings/gpio/led.txt | 14 ++++---------- Documentation/devicetree/bindings/leds/common.txt | 23 +++++++++++++++++++++++ 2 files changed, 27 insertions(+), 10 deletions(-) create mode 100644 Documentation/devicetree/bindings/leds/common.txt diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt index edc83c1c0d54..df1b3080f6b8 100644 --- a/Documentation/devicetree/bindings/gpio/led.txt +++ b/Documentation/devicetree/bindings/gpio/led.txt @@ -10,16 +10,10 @@ LED sub-node properties: - gpios : Should specify the LED's GPIO, see "gpios property" in Documentation/devicetree/bindings/gpio/gpio.txt. Active low LEDs should be indicated using flags in the GPIO specifier. -- label : (optional) The label for this LED. If omitted, the label is - taken from the node name (excluding the unit address). -- linux,default-trigger : (optional) This parameter, if present, is a - string defining the trigger assigned to the LED. Current triggers are: - "backlight" - LED will act as a back-light, controlled by the framebuffer - system - "default-on" - LED will turn on, but see "default-state" below - "heartbeat" - LED "double" flashes at a load average based rate - "ide-disk" - LED indicates disk activity - "timer" - LED flashes at a fixed, configurable rate +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt - default-state: (optional) The initial state of the LED. Valid values are "on", "off", and "keep". If the LED is already on or off and the default-state property is set the to same value, then no diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt new file mode 100644 index 000000000000..2d88816dd550 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -0,0 +1,23 @@ +Common leds properties. + +Optional properties for child nodes: +- label : The label for this LED. If omitted, the label is + taken from the node name (excluding the unit address). + +- linux,default-trigger : This parameter, if present, is a + string defining the trigger assigned to the LED. Current triggers are: + "backlight" - LED will act as a back-light, controlled by the framebuffer + system + "default-on" - LED will turn on (but for leds-gpio see "default-state" + property in Documentation/devicetree/bindings/gpio/led.txt) + "heartbeat" - LED "double" flashes at a load average based rate + "ide-disk" - LED indicates disk activity + "timer" - LED flashes at a fixed, configurable rate + +Examples: + +system-status { + label = "Status"; + linux,default-trigger = "heartbeat"; + ... +}; -- cgit v1.2.3 From 4f3be1cfa8422c93271dcdb59f223f6c84c70804 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Fri, 16 Nov 2012 15:53:14 +0900 Subject: script: dtc: clean generated files Fix "make distclean" to clean up generated dtc files. Without this patch the following files are left around: - dtc-lexer.lex.c - dtc-parser.tab.c - dtc-parser.tab.h Signed-off-by: Magnus Damm Reviewed-by: Simon Horman Signed-off-by: Grant Likely --- scripts/dtc/Makefile | 2 ++ 1 file changed, 2 insertions(+) diff --git a/scripts/dtc/Makefile b/scripts/dtc/Makefile index 6d1c6bb9f224..2a48022c41e7 100644 --- a/scripts/dtc/Makefile +++ b/scripts/dtc/Makefile @@ -27,3 +27,5 @@ HOSTCFLAGS_dtc-parser.tab.o := $(HOSTCFLAGS_DTC) # dependencies on generated files need to be listed explicitly $(obj)/dtc-lexer.lex.o: $(obj)/dtc-parser.tab.h +# generated files need to be cleaned explicitly +clean-files := dtc-lexer.lex.c dtc-parser.tab.c dtc-parser.tab.h -- cgit v1.2.3 From 155dd0c2f7c24c1531a90229f1c749cebf3f21f7 Mon Sep 17 00:00:00 2001 From: "Chaiken, Alison" Date: Thu, 15 Nov 2012 23:32:51 +0000 Subject: Documentation: correct of_platform_populate() argument list The documentation doesn't match the actual function prototype. This is a trivial patch to fix it. Signed-off-by: Alison Chaiken Acked-by: Arnd Bergmann Signed-off-by: Grant Likely --- Documentation/devicetree/usage-model.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Documentation/devicetree/usage-model.txt b/Documentation/devicetree/usage-model.txt index dca90fe22a90..ef9d06c9f8fd 100644 --- a/Documentation/devicetree/usage-model.txt +++ b/Documentation/devicetree/usage-model.txt @@ -347,7 +347,7 @@ later), which will happily live at the base of the Linux /sys/devices tree. Therefore, if a DT node is at the root of the tree, then it really probably is best registered as a platform_device. -Linux board support code calls of_platform_populate(NULL, NULL, NULL) +Linux board support code calls of_platform_populate(NULL, NULL, NULL, NULL) to kick off discovery of devices at the root of the tree. The parameters are all NULL because when starting from the root of the tree, there is no need to provide a starting node (the first NULL), a -- cgit v1.2.3