From 4fd6b5735c03c0955d93960d31f17d7144f5578f Mon Sep 17 00:00:00 2001 From: Robin Gong Date: Fri, 22 May 2020 18:44:50 +0800 Subject: arm64: dts: imx8mm-evk: correct ldo1/ldo2 voltage range Correct ldo1 voltage range from wrong high group(3.0V~3.3V) to low group (1.6V~1.9V) because the ldo1 should be 1.8V. Actually, two voltage groups have been supported at bd718x7-regulator driver, hence, just corrrect the voltage range to 1.6V~3.3V. For ldo2@0.8V, correct voltage range too. Otherwise, ldo1 would be kept @3.0V and ldo2@0.9V which violate i.mx8mm datasheet as the below warning log in kernel: [ 0.995524] LDO1: Bringing 1800000uV into 3000000-3000000uV [ 0.999196] LDO2: Bringing 800000uV into 900000-900000uV Fixes: 78cc25fa265d ("arm64: dts: imx8mm-evk: Add BD71847 PMIC") Cc: stable@vger.kernel.org Signed-off-by: Robin Gong Reviewed-by: Dong Aisheng Reviewed-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts index e5ec8322796d..0f1d7f8aeac4 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts @@ -208,7 +208,7 @@ ldo1_reg: LDO1 { regulator-name = "LDO1"; - regulator-min-microvolt = <3000000>; + regulator-min-microvolt = <1600000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; @@ -216,7 +216,7 @@ ldo2_reg: LDO2 { regulator-name = "LDO2"; - regulator-min-microvolt = <900000>; + regulator-min-microvolt = <800000>; regulator-max-microvolt = <900000>; regulator-boot-on; regulator-always-on; -- cgit v1.2.3 From cfb12c8952f617df58d73d24161e539a035d82b0 Mon Sep 17 00:00:00 2001 From: Robin Gong Date: Fri, 22 May 2020 18:44:51 +0800 Subject: arm64: dts: imx8mn-ddr4-evk: correct ldo1/ldo2 voltage range Correct ldo1 voltage range from wrong high group(3.0V~3.3V) to low group (1.6V~1.9V) because the ldo1 should be 1.8V. Actually, two voltage groups have been supported at bd718x7-regulator driver, hence, just corrrect the voltage range to 1.6V~3.3V. For ldo2@0.8V, correct voltage range too. Otherwise, ldo1 would be kept @3.0V and ldo2@0.9V which violate i.mx8mn datasheet as the below warning log in kernel: [ 0.995524] LDO1: Bringing 1800000uV into 3000000-3000000uV [ 0.999196] LDO2: Bringing 800000uV into 900000-900000uV Fixes: 3e44dd09736d ("arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support") Cc: stable@vger.kernel.org Signed-off-by: Robin Gong Reviewed-by: Dong Aisheng Reviewed-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts index d07e0e6a00cc..a1e5483dbbbe 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts @@ -113,7 +113,7 @@ ldo1_reg: LDO1 { regulator-name = "LDO1"; - regulator-min-microvolt = <3000000>; + regulator-min-microvolt = <1600000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; @@ -121,7 +121,7 @@ ldo2_reg: LDO2 { regulator-name = "LDO2"; - regulator-min-microvolt = <900000>; + regulator-min-microvolt = <800000>; regulator-max-microvolt = <900000>; regulator-boot-on; regulator-always-on; -- cgit v1.2.3 From e353b325948d04f1305a7b4ad32eca87ba0823a2 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Tue, 26 May 2020 12:09:39 -0500 Subject: arm64: dts: imx8mm-beacon: Fix voltages on LDO1 and LDO2 LDO1 and LDO2 settings are wrong and case the voltage to go above the maximum level of 2.15V permitted by the SoC to 3.0V. This patch is based on work done on the i.MX8M Mini-EVK which utilizes the same fix. Fixes: 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit") Signed-off-by: Adam Ford Reviewed-by: Daniel Baluta Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi index fb0137a8611c..94911b1707ef 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi @@ -136,7 +136,7 @@ ldo1_reg: LDO1 { regulator-name = "LDO1"; - regulator-min-microvolt = <3000000>; + regulator-min-microvolt = <1600000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; @@ -144,7 +144,7 @@ ldo2_reg: LDO2 { regulator-name = "LDO2"; - regulator-min-microvolt = <900000>; + regulator-min-microvolt = <800000>; regulator-max-microvolt = <900000>; regulator-boot-on; regulator-always-on; -- cgit v1.2.3 From 04a2c05179b732a4c097f0a9c701ef4c9a37e1e3 Mon Sep 17 00:00:00 2001 From: Frieder Schrempf Date: Thu, 28 May 2020 14:43:42 +0000 Subject: ARM: dts: imx6ul-kontron: Move watchdog from Kontron i.MX6UL/ULL board to SoM The watchdog's WDOG_ANY signal is used to trigger a POR of the SoC, if a soft reset is issued. As the SoM hardware connects the WDOG_ANY and the POR signals, the watchdog node itself and the pin configuration should be part of the common SoM devicetree. Let's move it from the baseboard's devicetree to its proper place. Fixes: 1ea4b76cdfde ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards") Cc: stable@vger.kernel.org Signed-off-by: Frieder Schrempf Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi | 13 ------------- arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi | 13 +++++++++++++ 2 files changed, 13 insertions(+), 13 deletions(-) diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi index f05e91841202..53a25fba34f6 100644 --- a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi +++ b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi @@ -232,13 +232,6 @@ status = "okay"; }; -&wdog1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_wdog>; - fsl,ext-reset-output; - status = "okay"; -}; - &iomuxc { pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>; @@ -409,10 +402,4 @@ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9 >; }; - - pinctrl_wdog: wdoggrp { - fsl,pins = < - MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0 - >; - }; }; diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi index a17af4d9bfdf..fc316408721d 100644 --- a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi +++ b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi @@ -57,6 +57,13 @@ status = "okay"; }; +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + &iomuxc { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_reset_out>; @@ -106,4 +113,10 @@ MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x1b0b0 >; }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0 + >; + }; }; -- cgit v1.2.3 From d22a16cc92e04d053fd807ef3587e4f135e4206f Mon Sep 17 00:00:00 2001 From: Frieder Schrempf Date: Thu, 28 May 2020 14:43:43 +0000 Subject: ARM: dts: imx6ul-kontron: Change WDOG_ANY signal from push-pull to open-drain The WDOG_ANY signal is connected to the RESET_IN signal of the SoM and baseboard. It is currently configured as push-pull, which means that if some external device like a programmer wants to assert the RESET_IN signal by pulling it to ground, it drives against the high level WDOG_ANY output of the SoC. To fix this we set the WDOG_ANY signal to open-drain configuration. That way we make sure that the RESET_IN can be asserted by the watchdog as well as by external devices. Fixes: 1ea4b76cdfde ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards") Cc: stable@vger.kernel.org Signed-off-by: Frieder Schrempf Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi index fc316408721d..61ba21a605a8 100644 --- a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi +++ b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi @@ -116,7 +116,7 @@ pinctrl_wdog: wdoggrp { fsl,pins = < - MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0 + MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x18b0 >; }; }; -- cgit v1.2.3 From c95c9693b112f312b59c5d100fd09a1349970fab Mon Sep 17 00:00:00 2001 From: Anson Huang Date: Wed, 10 Jun 2020 18:03:02 +0800 Subject: soc: imx8m: Correct i.MX8MP UID fuse offset Correct i.MX8MP UID fuse offset according to fuse map: UID_LOW: 0x420 UID_HIGH: 0x430 Fixes: fc40200ebf82 ("soc: imx: increase build coverage for imx8m soc driver") Fixes: 18f662a73862 ("soc: imx: Add i.MX8MP SoC driver support") Signed-off-by: Anson Huang Reviewed-by: Iuliana Prodan Signed-off-by: Shawn Guo --- drivers/soc/imx/soc-imx8m.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/drivers/soc/imx/soc-imx8m.c b/drivers/soc/imx/soc-imx8m.c index 7b0759adb47d..0bc831499bd8 100644 --- a/drivers/soc/imx/soc-imx8m.c +++ b/drivers/soc/imx/soc-imx8m.c @@ -22,6 +22,8 @@ #define OCOTP_UID_LOW 0x410 #define OCOTP_UID_HIGH 0x420 +#define IMX8MP_OCOTP_UID_OFFSET 0x10 + /* Same as ANADIG_DIGPROG_IMX7D */ #define ANADIG_DIGPROG_IMX8MM 0x800 @@ -87,6 +89,8 @@ static void __init imx8mm_soc_uid(void) { void __iomem *ocotp_base; struct device_node *np; + u32 offset = of_machine_is_compatible("fsl,imx8mp") ? + IMX8MP_OCOTP_UID_OFFSET : 0; np = of_find_compatible_node(NULL, NULL, "fsl,imx8mm-ocotp"); if (!np) @@ -95,9 +99,9 @@ static void __init imx8mm_soc_uid(void) ocotp_base = of_iomap(np, 0); WARN_ON(!ocotp_base); - soc_uid = readl_relaxed(ocotp_base + OCOTP_UID_HIGH); + soc_uid = readl_relaxed(ocotp_base + OCOTP_UID_HIGH + offset); soc_uid <<= 32; - soc_uid |= readl_relaxed(ocotp_base + OCOTP_UID_LOW); + soc_uid |= readl_relaxed(ocotp_base + OCOTP_UID_LOW + offset); iounmap(ocotp_base); of_node_put(np); -- cgit v1.2.3 From 586745f1598ccf71b0a5a6df2222dee0a865954e Mon Sep 17 00:00:00 2001 From: yu kuai Date: Thu, 4 Jun 2020 20:42:06 +0800 Subject: ARM: imx5: add missing put_device() call in imx_suspend_alloc_ocram() if of_find_device_by_node() succeed, imx_suspend_alloc_ocram() doesn't have a corresponding put_device(). Thus add a jump target to fix the exception handling for this function implementation. Fixes: 1579c7b9fe01 ("ARM: imx53: Set DDR pins to high impedance when in suspend to RAM.") Signed-off-by: yu kuai Signed-off-by: Shawn Guo --- arch/arm/mach-imx/pm-imx5.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-imx/pm-imx5.c b/arch/arm/mach-imx/pm-imx5.c index f057df813f83..e9962b48e30c 100644 --- a/arch/arm/mach-imx/pm-imx5.c +++ b/arch/arm/mach-imx/pm-imx5.c @@ -295,14 +295,14 @@ static int __init imx_suspend_alloc_ocram( if (!ocram_pool) { pr_warn("%s: ocram pool unavailable!\n", __func__); ret = -ENODEV; - goto put_node; + goto put_device; } ocram_base = gen_pool_alloc(ocram_pool, size); if (!ocram_base) { pr_warn("%s: unable to alloc ocram!\n", __func__); ret = -ENOMEM; - goto put_node; + goto put_device; } phys = gen_pool_virt_to_phys(ocram_pool, ocram_base); @@ -312,6 +312,8 @@ static int __init imx_suspend_alloc_ocram( if (virt_out) *virt_out = virt; +put_device: + put_device(&pdev->dev); put_node: of_node_put(node); -- cgit v1.2.3 From 4845446036fc9c13f43b54a65c9b757c14f5141b Mon Sep 17 00:00:00 2001 From: yu kuai Date: Thu, 4 Jun 2020 20:54:49 +0800 Subject: ARM: imx6: add missing put_device() call in imx6q_suspend_init() if of_find_device_by_node() succeed, imx6q_suspend_init() doesn't have a corresponding put_device(). Thus add a jump target to fix the exception handling for this function implementation. Signed-off-by: yu kuai Signed-off-by: Shawn Guo --- arch/arm/mach-imx/pm-imx6.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) diff --git a/arch/arm/mach-imx/pm-imx6.c b/arch/arm/mach-imx/pm-imx6.c index dd34dff13762..40c74b4c4d73 100644 --- a/arch/arm/mach-imx/pm-imx6.c +++ b/arch/arm/mach-imx/pm-imx6.c @@ -493,14 +493,14 @@ static int __init imx6q_suspend_init(const struct imx6_pm_socdata *socdata) if (!ocram_pool) { pr_warn("%s: ocram pool unavailable!\n", __func__); ret = -ENODEV; - goto put_node; + goto put_device; } ocram_base = gen_pool_alloc(ocram_pool, MX6Q_SUSPEND_OCRAM_SIZE); if (!ocram_base) { pr_warn("%s: unable to alloc ocram!\n", __func__); ret = -ENOMEM; - goto put_node; + goto put_device; } ocram_pbase = gen_pool_virt_to_phys(ocram_pool, ocram_base); @@ -523,7 +523,7 @@ static int __init imx6q_suspend_init(const struct imx6_pm_socdata *socdata) ret = imx6_pm_get_base(&pm_info->mmdc_base, socdata->mmdc_compat); if (ret) { pr_warn("%s: failed to get mmdc base %d!\n", __func__, ret); - goto put_node; + goto put_device; } ret = imx6_pm_get_base(&pm_info->src_base, socdata->src_compat); @@ -570,7 +570,7 @@ static int __init imx6q_suspend_init(const struct imx6_pm_socdata *socdata) &imx6_suspend, MX6Q_SUSPEND_OCRAM_SIZE - sizeof(*pm_info)); - goto put_node; + goto put_device; pl310_cache_map_failed: iounmap(pm_info->gpc_base.vbase); @@ -580,6 +580,8 @@ iomuxc_map_failed: iounmap(pm_info->src_base.vbase); src_map_failed: iounmap(pm_info->mmdc_base.vbase); +put_device: + put_device(&pdev->dev); put_node: of_node_put(node); -- cgit v1.2.3 From a721321446432c3899aeca16cc6ddc30422b7f74 Mon Sep 17 00:00:00 2001 From: Peng Fan Date: Wed, 24 Jun 2020 14:06:54 +0800 Subject: soc: imx8m: fix build warning Fix the build warning with x86_64-randconfig >> drivers/soc/imx/soc-imx8m.c:150:34: warning: unused variable >> 'imx8_soc_match' [-Wunused-const-variable] static const struct of_device_id imx8_soc_match[] = { ^ Fixes: fc40200ebf82 ("soc: imx: increase build coverage for imx8m soc driver") Reported-by: kernel test robot Signed-off-by: Peng Fan Signed-off-by: Shawn Guo --- drivers/soc/imx/soc-imx8m.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/soc/imx/soc-imx8m.c b/drivers/soc/imx/soc-imx8m.c index 0bc831499bd8..cc57a384d74d 100644 --- a/drivers/soc/imx/soc-imx8m.c +++ b/drivers/soc/imx/soc-imx8m.c @@ -150,7 +150,7 @@ static const struct imx8_soc_data imx8mp_soc_data = { .soc_revision = imx8mm_soc_revision, }; -static const struct of_device_id imx8_soc_match[] = { +static __maybe_unused const struct of_device_id imx8_soc_match[] = { { .compatible = "fsl,imx8mq", .data = &imx8mq_soc_data, }, { .compatible = "fsl,imx8mm", .data = &imx8mm_soc_data, }, { .compatible = "fsl,imx8mn", .data = &imx8mn_soc_data, }, -- cgit v1.2.3