From a66c5ed539277b9f2363bbace0dba88b85b36c26 Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Thu, 6 Jan 2022 11:48:52 -0800 Subject: hwmon: (lm90) Reduce maximum conversion rate for G781 According to its datasheet, G781 supports a maximum conversion rate value of 8 (62.5 ms). However, chips labeled G781 and G780 were found to only support a maximum conversion rate value of 7 (125 ms). On the other side, chips labeled G781-1 and G784 were found to support a conversion rate value of 8. There is no known means to distinguish G780 from G781 or G784; all chips report the same manufacturer ID and chip revision. Setting the conversion rate register value to 8 on chips not supporting it causes unexpected behavior since the real conversion rate is set to 0 (16 seconds) if a value of 8 is written into the conversion rate register. Limit the conversion rate register value to 7 for all G78x chips to avoid the problem. Fixes: ae544f64cc7b ("hwmon: (lm90) Add support for GMT G781") Signed-off-by: Guenter Roeck --- drivers/hwmon/lm90.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c index 74019dff2550..cc5e48fe304b 100644 --- a/drivers/hwmon/lm90.c +++ b/drivers/hwmon/lm90.c @@ -373,7 +373,7 @@ static const struct lm90_params lm90_params[] = { .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_CRIT, .alert_alarms = 0x7c, - .max_convrate = 8, + .max_convrate = 7, }, [lm86] = { .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT -- cgit v1.2.3 From bc341a1a98827925082e95db174734fc8bd68af6 Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Sat, 8 Jan 2022 11:37:19 -0800 Subject: hwmon: (lm90) Re-enable interrupts after alert clears If alert handling is broken, interrupts are disabled after an alert and re-enabled after the alert clears. However, if there is an interrupt handler, this does not apply if alerts were originally disabled and enabled when the driver was loaded. In that case, interrupts will stay disabled after an alert was handled though the alert handler even after the alert condition clears. Address the situation by always re-enabling interrupts after the alert condition clears if there is an interrupt handler. Fixes: 2abdc357c55d9 ("hwmon: (lm90) Unmask hardware interrupt") Cc: Dmitry Osipenko Signed-off-by: Guenter Roeck --- drivers/hwmon/lm90.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c index cc5e48fe304b..e4ecf3440d7c 100644 --- a/drivers/hwmon/lm90.c +++ b/drivers/hwmon/lm90.c @@ -848,7 +848,7 @@ static int lm90_update_device(struct device *dev) * Re-enable ALERT# output if it was originally enabled and * relevant alarms are all clear */ - if (!(data->config_orig & 0x80) && + if ((client->irq || !(data->config_orig & 0x80)) && !(data->alarms & data->alert_alarms)) { if (data->config & 0x80) { dev_dbg(&client->dev, "Re-enabling ALERT#\n"); -- cgit v1.2.3 From a53fff96f35763d132a36c620b183fdf11022d7a Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Fri, 7 Jan 2022 11:05:23 -0800 Subject: hwmon: (lm90) Mark alert as broken for MAX6654 Experiments with MAX6654 show that its alert function is broken, similar to other chips supported by the lm90 driver. Mark it accordingly. Fixes: 229d495d8189 ("hwmon: (lm90) Add max6654 support to lm90 driver") Cc: Josh Lehan Signed-off-by: Guenter Roeck --- drivers/hwmon/lm90.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c index e4ecf3440d7c..280ae5f58187 100644 --- a/drivers/hwmon/lm90.c +++ b/drivers/hwmon/lm90.c @@ -400,6 +400,7 @@ static const struct lm90_params lm90_params[] = { .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL, }, [max6654] = { + .flags = LM90_HAVE_BROKEN_ALERT, .alert_alarms = 0x7c, .max_convrate = 7, .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL, -- cgit v1.2.3 From 94746b0ba479743355e0d3cc1cb9cfe3011fb8be Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Fri, 7 Jan 2022 11:11:00 -0800 Subject: hwmon: (lm90) Mark alert as broken for MAX6680 Experiments with MAX6680 and MAX6681 show that the alert function of those chips is broken, similar to other chips supported by the lm90 driver. Mark it accordingly. Fixes: 4667bcb8d8fc ("hwmon: (lm90) Introduce chip parameter structure") Signed-off-by: Guenter Roeck --- drivers/hwmon/lm90.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c index 280ae5f58187..06cb971c889b 100644 --- a/drivers/hwmon/lm90.c +++ b/drivers/hwmon/lm90.c @@ -419,7 +419,7 @@ static const struct lm90_params lm90_params[] = { }, [max6680] = { .flags = LM90_HAVE_OFFSET | LM90_HAVE_CRIT - | LM90_HAVE_CRIT_ALRM_SWP, + | LM90_HAVE_CRIT_ALRM_SWP | LM90_HAVE_BROKEN_ALERT, .alert_alarms = 0x7c, .max_convrate = 7, }, -- cgit v1.2.3 From f614629f9c1080dcc844a8430e3fb4c37ebbf05d Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Fri, 7 Jan 2022 12:36:41 -0800 Subject: hwmon: (lm90) Mark alert as broken for MAX6646/6647/6649 Experiments with MAX6646 and MAX6648 show that the alert function of those chips is broken, similar to other chips supported by the lm90 driver. Mark it accordingly. Fixes: 4667bcb8d8fc ("hwmon: (lm90) Introduce chip parameter structure") Signed-off-by: Guenter Roeck --- drivers/hwmon/lm90.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c index 06cb971c889b..ba01127c1deb 100644 --- a/drivers/hwmon/lm90.c +++ b/drivers/hwmon/lm90.c @@ -394,7 +394,7 @@ static const struct lm90_params lm90_params[] = { .max_convrate = 9, }, [max6646] = { - .flags = LM90_HAVE_CRIT, + .flags = LM90_HAVE_CRIT | LM90_HAVE_BROKEN_ALERT, .alert_alarms = 0x7c, .max_convrate = 6, .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL, -- cgit v1.2.3 From d379880d9adb9f1ada3f1266aa49ea2561328e08 Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Mon, 10 Jan 2022 23:23:31 -0800 Subject: hwmon: (lm90) Fix sysfs and udev notifications sysfs and udev notifications need to be sent to the _alarm attributes, not to the value attributes. Fixes: 94dbd23ed88c ("hwmon: (lm90) Use hwmon_notify_event()") Cc: Dmitry Osipenko Signed-off-by: Guenter Roeck --- drivers/hwmon/lm90.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c index ba01127c1deb..1c9493c70813 100644 --- a/drivers/hwmon/lm90.c +++ b/drivers/hwmon/lm90.c @@ -1808,22 +1808,22 @@ static bool lm90_is_tripped(struct i2c_client *client, u16 *status) if (st & LM90_STATUS_LLOW) hwmon_notify_event(data->hwmon_dev, hwmon_temp, - hwmon_temp_min, 0); + hwmon_temp_min_alarm, 0); if (st & LM90_STATUS_RLOW) hwmon_notify_event(data->hwmon_dev, hwmon_temp, - hwmon_temp_min, 1); + hwmon_temp_min_alarm, 1); if (st2 & MAX6696_STATUS2_R2LOW) hwmon_notify_event(data->hwmon_dev, hwmon_temp, - hwmon_temp_min, 2); + hwmon_temp_min_alarm, 2); if (st & LM90_STATUS_LHIGH) hwmon_notify_event(data->hwmon_dev, hwmon_temp, - hwmon_temp_max, 0); + hwmon_temp_max_alarm, 0); if (st & LM90_STATUS_RHIGH) hwmon_notify_event(data->hwmon_dev, hwmon_temp, - hwmon_temp_max, 1); + hwmon_temp_max_alarm, 1); if (st2 & MAX6696_STATUS2_R2HIGH) hwmon_notify_event(data->hwmon_dev, hwmon_temp, - hwmon_temp_max, 2); + hwmon_temp_max_alarm, 2); return true; } -- cgit v1.2.3 From f1e75e0d6a1ae02fa4189d7aeebab623bade2a21 Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Tue, 18 Jan 2022 07:53:19 -0800 Subject: hwmon: (pmbus/ir38064) Mark ir38064_of_match as __maybe_unused If CONFIG_PM is not enabled, the following warning is reported. drivers/hwmon/pmbus/ir38064.c:54:34: warning: unused variable 'ir38064_of_match' Mark it as __maybe_unused. Reported-by: kernel test robot Cc: Arthur Heymans Signed-off-by: Guenter Roeck --- drivers/hwmon/pmbus/ir38064.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/hwmon/pmbus/ir38064.c b/drivers/hwmon/pmbus/ir38064.c index 0ea7e1c18bdc..09276e397194 100644 --- a/drivers/hwmon/pmbus/ir38064.c +++ b/drivers/hwmon/pmbus/ir38064.c @@ -62,7 +62,7 @@ static const struct i2c_device_id ir38064_id[] = { MODULE_DEVICE_TABLE(i2c, ir38064_id); -static const struct of_device_id ir38064_of_match[] = { +static const struct of_device_id __maybe_unused ir38064_of_match[] = { { .compatible = "infineon,ir38060" }, { .compatible = "infineon,ir38064" }, { .compatible = "infineon,ir38164" }, -- cgit v1.2.3 From c1ec0cabc36718efc7fe8b4157d41b82d08ec1d2 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Fri, 21 Jan 2022 14:55:43 +0300 Subject: hwmon: (adt7470) Prevent divide by zero in adt7470_fan_write() The "val" variable is controlled by the user and comes from hwmon_attr_store(). The FAN_RPM_TO_PERIOD() macro divides by "val" so a zero will crash the system. Check for that and return -EINVAL. Negatives are also invalid so return -EINVAL for those too. Fixes: fc958a61ff6d ("hwmon: (adt7470) Convert to devm_hwmon_device_register_with_info API") Signed-off-by: Dan Carpenter Signed-off-by: Guenter Roeck --- drivers/hwmon/adt7470.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/hwmon/adt7470.c b/drivers/hwmon/adt7470.c index d519aca4a9d6..fb6d14d213a1 100644 --- a/drivers/hwmon/adt7470.c +++ b/drivers/hwmon/adt7470.c @@ -662,6 +662,9 @@ static int adt7470_fan_write(struct device *dev, u32 attr, int channel, long val struct adt7470_data *data = dev_get_drvdata(dev); int err; + if (val <= 0) + return -EINVAL; + val = FAN_RPM_TO_PERIOD(val); val = clamp_val(val, 1, 65534); -- cgit v1.2.3 From 79da533d3cc717ccc05ddbd3190da8a72bc2408b Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Sun, 23 Jan 2022 18:23:22 -0800 Subject: hwmon: (nct6775) Fix crash in clear_caseopen MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Paweł Marciniak reports the following crash, observed when clearing the chassis intrusion alarm. BUG: kernel NULL pointer dereference, address: 0000000000000028 PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 3 PID: 4815 Comm: bash Tainted: G S 5.16.2-200.fc35.x86_64 #1 Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./Z97 Extreme4, BIOS P2.60A 05/03/2018 RIP: 0010:clear_caseopen+0x5a/0x120 [nct6775] Code: 68 70 e8 e9 32 b1 e3 85 c0 0f 85 d2 00 00 00 48 83 7c 24 ... RSP: 0018:ffffabcb02803dd8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000 RDX: ffff8e8808192880 RSI: 0000000000000000 RDI: ffff8e87c7509a68 RBP: 0000000000000000 R08: 0000000000000001 R09: 000000000000000a R10: 000000000000000a R11: f000000000000000 R12: 000000000000001f R13: ffff8e87c7509828 R14: ffff8e87c7509a68 R15: ffff8e88494527a0 FS: 00007f4db9151740(0000) GS:ffff8e8ebfec0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000028 CR3: 0000000166b66001 CR4: 00000000001706e0 Call Trace: kernfs_fop_write_iter+0x11c/0x1b0 new_sync_write+0x10b/0x180 vfs_write+0x209/0x2a0 ksys_write+0x4f/0xc0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae The problem is that the device passed to clear_caseopen() is the hwmon device, not the platform device, and the platform data is not set in the hwmon device. Store the pointer to sio_data in struct nct6775_data and get if from there if needed. Fixes: 2e7b9886968b ("hwmon: (nct6775) Use superio_*() function pointers in sio_data.") Cc: Denis Pauk Cc: Bernhard Seibold Reported-by: Paweł Marciniak Tested-by: Denis Pauk Signed-off-by: Guenter Roeck --- drivers/hwmon/nct6775.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/hwmon/nct6775.c b/drivers/hwmon/nct6775.c index fd3f91cb01c6..098d12b9ecda 100644 --- a/drivers/hwmon/nct6775.c +++ b/drivers/hwmon/nct6775.c @@ -1175,7 +1175,7 @@ static inline u8 in_to_reg(u32 val, u8 nr) struct nct6775_data { int addr; /* IO base of hw monitor block */ - int sioreg; /* SIO register address */ + struct nct6775_sio_data *sio_data; enum kinds kind; const char *name; @@ -3559,7 +3559,7 @@ clear_caseopen(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) { struct nct6775_data *data = dev_get_drvdata(dev); - struct nct6775_sio_data *sio_data = dev_get_platdata(dev); + struct nct6775_sio_data *sio_data = data->sio_data; int nr = to_sensor_dev_attr(attr)->index - INTRUSION_ALARM_BASE; unsigned long val; u8 reg; @@ -3967,7 +3967,7 @@ static int nct6775_probe(struct platform_device *pdev) return -ENOMEM; data->kind = sio_data->kind; - data->sioreg = sio_data->sioreg; + data->sio_data = sio_data; if (sio_data->access == access_direct) { data->addr = res->start; -- cgit v1.2.3