Age | Commit message (Collapse) | Author | Files | Lines |
|
'arm/mediatek', 'arm/core', 'x86/vt-d' and 'core' into next
|
|
Since commit f3b0946d629c ("genirq/msi: Make sure PCI MSIs are
activated early"), we can end-up activating a PCI/MSI twice (once
at allocation time, and once at startup time).
This is normally of no consequences, except that there is some
HW out there that may misbehave if activate is used more than once
(the GICv3 ITS, for example, uses the activate callback
to issue the MAPVI command, and the architecture spec says that
"If there is an existing mapping for the EventID-DeviceID
combination, behavior is UNPREDICTABLE").
While this could be worked around in each individual driver, it may
make more sense to tackle the issue at the core level. In order to
avoid getting in that situation, let's have a per-interrupt flag
to remember if we have already activated that interrupt or not.
Fixes: f3b0946d629c ("genirq/msi: Make sure PCI MSIs are activated early")
Reported-and-tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1484668848-24361-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This new function checks whether all MSI irq domains
implement IRQ remapping. This is useful to understand
whether VFIO passthrough is safe with respect to interrupts.
On ARM typically an MSI controller can sit downstream
to the IOMMU without preventing VFIO passthrough.
As such any assigned device can write into the MSI doorbell.
In case the MSI controller implements IRQ remapping, assigned
devices will not be able to trigger interrupts towards the
host. On the contrary, the assignment must be emphasized as
unsafe with respect to interrupts.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We introduce two new enum values for the irq domain flag:
- IRQ_DOMAIN_FLAG_MSI indicates the irq domain corresponds to
an MSI domain
- IRQ_DOMAIN_FLAG_MSI_REMAP indicates the irq domain has MSI
remapping capabilities.
Those values will be useful to check all MSI irq domains have
MSI remapping support when assessing the safety of IRQ assignment
to a guest.
irq_domain_hierarchical_is_msi_remap() allows to check if an
irq domain or any parent implements MSI remapping.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Commit 1bf4ddc46c5d ("irqdomain: Introduce irq_domain_create_{linear,
tree}") introduced the use of fwnode_handle to identify the interrupt
controller when calling __irq_domain_add but missed updating the kernel
doc parameters for the function.
Update this comment. While we are touching this code, also consolidate
the declaration and assignment of of_node.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Marc Zygnier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1464699409-23113-1-git-send-email-punit.agrawal@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
According to the xlate() callback definition, the 'out_type' parameter
needs to be the "linux irq type".
A mask for such bits exists, IRQ_TYPE_SENSE_MASK, which is correctly
applied in irq_domain_xlate_twocell()
So use it for irq_domain_xlate_onetwocell() as well.
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mason <slash.tmp@free.fr>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/57A05F5D.103@laposte.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
If an irq_domain is auto-recursive and irq_domain_alloc_irqs_recursive()
for its parent has returned an error, then do return and avoid calling
irq_domain_free_irqs_recursive() uselessly, because:
- if domain->ops->alloc() had failed for an auto-recursive irq_domain,
then irq_domain_free_irqs_recursive() had already been called;
- if domain->ops->alloc() had failed for a not auto-recursive irq_domain,
then there is nothing to free at all.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1467505448-2850-1-git-send-email-alex.popov@linux.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Pull the irq affinity managing code which is in a seperate branch for block
developers to pull.
|
|
Add an extra argument to the irq(domain) allocation functions, so we can hand
down affinity hints to the allocator. Thats necessary to implement proper
support for multiqueue devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Cc: axboe@fb.com
Cc: agordeev@redhat.com
Link: http://lkml.kernel.org/r/1467621574-8277-4-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The function irq_create_of_mapping() is used to create an interrupt
mapping. However, depending on whether the irqdomain, to which the
interrupt belongs, is part of a hierarchy, determines whether the
mapping is created via calling irq_domain_alloc_irqs() or
irq_create_mapping().
To dispose of the interrupt mapping, drivers call irq_dispose_mapping().
However, this function does not check to see if the irqdomain is part
of a hierarchy or not and simply assumes that it was mapped via calling
irq_create_mapping() so calls irq_domain_disassociate() to unmap the
interrupt.
Fix this by checking to see if the irqdomain is part of a hierarchy and
if so call irq_domain_free_irqs() to free/unmap the interrupt.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1466501002-16368-1-git-send-email-jonathanh@nvidia.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Some IRQ chips, such as GPIO controllers or secondary level interrupt
controllers, may require require additional runtime power management
control to ensure they are accessible. For such IRQ chips, it makes sense
to enable the IRQ chip when interrupts are requested and disabled them
again once all interrupts have been freed.
When mapping an IRQ, the IRQ type settings are read and then programmed.
The mapping of the IRQ happens before the IRQ is requested and so the
programming of the type settings occurs before the IRQ is requested. This
is a problem for IRQ chips that require additional power management
control because they may not be accessible yet. Therefore, when mapping
the IRQ, don't program the type settings, just save them and then program
these saved settings when the IRQ is requested (so long as if they are not
overridden via the call to request the IRQ).
Add a stub function for irq_domain_free_irqs() to avoid any compilation
errors when CONFIG_IRQ_DOMAIN_HIERARCHY is not selected.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
When mapping an IRQ, it is possible that a mapping for the IRQ already
exists. If mapping does exist then there are the following issues with
regard to the handling of the IRQ type settings ...
1. If the domain is part of a hierarchy, then:
a. We do not check that the type settings for the existing mapping
match those of the new mapping.
b. We do not check to see if the type settings have been programmed
yet (and they might not have been) and so we may never set the
type.
2. If the domain is NOT part of a hierarchy, we will overwrite the
current type settings programmed if they are different from the
previous mapping. Please note that irq_create_mapping()
calls irq_find_mapping() to check if a mapping already exists.
Although, it may be unlikely that the type settings for a shared
interrupt would not match, nonetheless we should check for this.
Therefore, to fix this check if a mapping exists (regardless of whether
the domain is part of a hierarchy or not) and if it does then:
1. Return the IRQ number if the type settings match or are not
specified.
2. Program the type settings and return the IRQ number if the type
settings have not been programmed yet.
3. Otherwise if the type setting do not match, then print a warning
and don't return the IRQ number.
Furthermore, add a warning if the type return by irq_domain_translate()
has bits outside the sense mask set and then clear these bits. If these
bits are not cleared then this will cause the comparision of the type
settings for an existing mapping to fail with that of the new mapping
even if the sense bit themselves match. The reason being is that the
existing type settings are read by calling irq_get_trigger_type() which
will clear any bits outside the sense mask. This will allow us to detect
irqchips that are not correctly clearing these bits and fix them.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Commit e61452365372 ("radix_tree: add support for multi-order entries")
left the impression that the support for multiorder radix tree entries
was functional. As soon as Ross tried to use it, it became apparent
that my testing was completely inadequate, and it didn't even work a
little bit for orders that were not a multiple of shift.
This series of patches is the result of about 6 weeks of redesign,
reimplementation, testing, arguing and hair-pulling. The great news is
that the test-suite is now far better than it was. That's reflected in
the diffstat for the test-suite alone:
12 files changed, 436 insertions(+), 28 deletions(-)
The highlight for users of the tree is that the restriction on the order
of inserted entries being >= RADIX_TREE_MAP_SHIFT is now gone; the radix
tree now supports any order between 0 and 64.
For those who are interested in how the tree works, patch 9 is probably
the most interesting one as it introduces the new machinery for handling
sibling entries.
I've tried to be fair in attributing authorship to the person who
contributed the majority of the code in each patch; Ross has been an
invaluable partner in the development of this support and it's fair to
say that each of us has code in every commit.
I should also express my appreciation of the 0day testing. It prompted
me that I was bloating the tinyconfig in an unacceptable way, and it
bisected to a commit which contained a rather nasty memory-corruption
bug.
This patch (of 29):
The irqdomain code was checking for 0 or 1 entries, not 0 entries like
the comment said they were. Introduce a new helper that will actually
check for an empty tree.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
|
|
When iterating over the irq domain list, we try to match a domain
either by calling a match() function or by comparing a number
of fields passed as parameters.
Both approaches are a bit restrictive:
- match() is DT specific and only takes a device node
- the fallback case only deals with the fwnode_handle
It would be useful if we had a per-domain function that would
actually perform the matching check on the whole of the
irq_fwspec structure. This would allow for a domain to triage
matching attempts that need to extend beyond the fwnode.
Let's introduce irq_find_matching_fwspec(), which takes a full
blown irq_fwspec structure, and call into a select() function
implemented by the irqdomain. irq_find_matching_fwnode() is
made a wrapper around irq_find_matching_fwspec in order to
preserve compatibility.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Link: http://lkml.kernel.org/r/1460365075-7316-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Export irq_domain_free_irqs_common so it can be used by modules.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Export irq_chip_*_parent(), irq_domain_create_hierarchy(),
irq_domain_set_hwirq_and_chip(), irq_domain_reset_irq_data(),
irq_domain_alloc/free_irqs_parent()
So gpio drivers can be built as modules. First user: gpio-xgene-sb
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Phong Vo <pvo@apm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: patches@apm.com
Cc: Loc Ho <lho@apm.com>
Cc: Keyur Chudgar <kchudgar@apm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: https://lists.01.org/pipermail/kbuild-all/2016-February/017914.html
Link: http://lkml.kernel.org/r/1457017012-10628-1-git-send-email-qnguyen@apm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We will need to use this function to implement irq_reserve_ipi() later. So
make it non static and move the prototype to irqdomain.h to allow using it
outside irqdomain.c
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-8-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull IRQ fixes from Ingo Molnar:
"Mostly irqchip driver fixes, but also an irq core crash fix and a
build fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mxs: Add missing set_handle_irq()
irqchip/atmel-aic: Fix wrong bit operation for IRQ priority
irqchip/gic-v3-its: Recompute the number of pages on page size change
base: Export platform_msi_domain_[alloc,free]_irqs
of: MSI: Simplify irqdomain lookup
irqdomain: Allow domain lookup with DOMAIN_BUS_WIRED token
irqchip: Fix dependencies for archs w/o HAS_IOMEM
irqchip/s3c24xx: Mark init_eint as __maybe_unused
genirq: Validate action before dereferencing it in handle_irq_event_percpu()
|
|
Let's take the (outlandish) example of an interrupt controller
capable of handling both wired interrupts and PCI MSIs.
With the current code, the PCI MSI domain is going to be tagged
with DOMAIN_BUS_PCI_MSI, and the wired domain with DOMAIN_BUS_ANY.
Things get hairy when we start looking up the domain for a wired
interrupt (typically when creating it based on some firmware
information - DT or ACPI).
In irq_create_fwspec_mapping(), we perform the lookup using
DOMAIN_BUS_ANY, which is actually used as a wildcard. This gives
us one chance out of two to end up with the wrong domain, and
we try to configure a wired interrupt with the MSI domain.
Everything grinds to a halt pretty quickly.
What we really need to do is to start looking for a domain that
would uniquely identify a wired interrupt domain, and only use
DOMAIN_BUS_ANY as a fallback.
In order to solve this, let's introduce a new DOMAIN_BUS_WIRED
token, which is going to be used exactly as described above.
Of course, this depends on the irqchip to setup the domain
bus_token, and nobody had to implement this so far.
Only so far.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1453816347-32720-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes for the v4.5 merge window:
Enumeration:
- Simplify config space size computation (Bjorn Helgaas)
- Avoid iterating through ROM outside the resource window (Edward O'Callaghan)
- Support PCIe devices with short cfg_size (Jason S. McMullan)
- Add Netronome vendor and device IDs (Jason S. McMullan)
- Limit config space size for Netronome NFP6000 family (Jason S. McMullan)
- Add Netronome NFP4000 PF device ID (Simon Horman)
- Limit config space size for Netronome NFP4000 (Simon Horman)
- Print warnings for all invalid expansion ROM headers (Vladis Dronov)
Resource management:
- Fix minimum allocation address overwrite (Christoph Biedl)
PCI device hotplug:
- acpiphp_ibm: Fix null dereferences on null ibm_slot (Colin Ian King)
- pciehp: Always protect pciehp_disable_slot() with hotplug mutex (Guenter Roeck)
- shpchp: Constify hpc_ops structure (Julia Lawall)
- ibmphp: Remove unneeded NULL test (Julia Lawall)
Power management:
- Make ASPM sysfs link_state_store() consistent with link_state_show() (Andy Lutomirski)
Virtualization
- Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183 (Tim Sander)
MSI:
- Remove empty pci_msi_init_pci_dev() (Bjorn Helgaas)
- Mark PCIe/PCI (MSI) IRQ cascade handlers as IRQF_NO_THREAD (Grygorii Strashko)
- Initialize MSI capability for all architectures (Guilherme G. Piccoli)
- Relax msi_domain_alloc() to support parentless MSI irqdomains (Liu Jiang)
ARM Versatile host bridge driver:
- Remove unused pci_sys_data structures (Lorenzo Pieralisi)
Broadcom iProc host bridge driver:
- Hide CONFIG_PCIE_IPROC (Arnd Bergmann)
- Do not use 0x in front of %pap (Dmitry V. Krivenok)
- Update iProc PCIe device tree binding (Ray Jui)
- Add PAXC interface support (Ray Jui)
- Add iProc PCIe MSI device tree binding (Ray Jui)
- Add iProc PCIe MSI support (Ray Jui)
Freescale i.MX6 host bridge driver:
- Use gpio_set_value_cansleep() (Fabio Estevam)
- Add support for active-low reset GPIO (Petr Štetiar)
HiSilicon host bridge driver:
- Add support for HiSilicon Hip06 PCIe host controllers (Gabriele Paoloni)
Intel VMD host bridge driver:
- Export irq_domain_set_info() for module use (Keith Busch)
- x86/PCI: Allow DMA ops specific to a PCI domain (Keith Busch)
- Use 32 bit PCI domain numbers (Keith Busch)
- Add driver for Intel Volume Management Device (VMD) (Keith Busch)
Qualcomm host bridge driver:
- Document PCIe devicetree bindings (Stanimir Varbanov)
- Add Qualcomm PCIe controller driver (Stanimir Varbanov)
- dts: apq8064: add PCIe devicetree node (Stanimir Varbanov)
- dts: ifc6410: enable PCIe DT node for this board (Stanimir Varbanov)
Renesas R-Car host bridge driver:
- Add support for R-Car H3 to pcie-rcar (Harunobu Kurokawa)
- Allow DT to override default window settings (Phil Edworthy)
- Convert to DT resource parsing API (Phil Edworthy)
- Revert "PCI: rcar: Build pcie-rcar.c only on ARM" (Phil Edworthy)
- Remove unused pci_sys_data struct from pcie-rcar (Phil Edworthy)
- Add runtime PM support to pcie-rcar (Phil Edworthy)
- Add Gen2 PHY setup to pcie-rcar (Phil Edworthy)
- Add gen2 fallback compatibility string for pci-rcar-gen2 (Simon Horman)
- Add gen2 fallback compatibility string for pcie-rcar (Simon Horman)
Synopsys DesignWare host bridge driver:
- Simplify control flow (Bjorn Helgaas)
- Make config accessor override checking symmetric (Bjorn Helgaas)
- Ensure ATU is enabled before IO/conf space accesses (Stanimir Varbanov)
Miscellaneous:
- Add of_pci_get_host_bridge_resources() stub (Arnd Bergmann)
- Check for PCI_HEADER_TYPE_BRIDGE equality, not bitmask (Bjorn Helgaas)
- Fix all whitespace issues (Bogicevic Sasa)
- x86/PCI: Simplify pci_bios_{read,write} (Geliang Tang)
- Use to_pci_dev() instead of open-coding it (Geliang Tang)
- Use kobj_to_dev() instead of open-coding it (Geliang Tang)
- Use list_for_each_entry() to simplify code (Geliang Tang)
- Fix typos in <linux/msi.h> (Thomas Petazzoni)
- x86/PCI: Clarify AMD Fam10h config access restrictions comment (Tomasz Nowicki)"
* tag 'pci-v4.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (58 commits)
PCI: Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183
PCI: Limit config space size for Netronome NFP4000
PCI: Add Netronome NFP4000 PF device ID
x86/PCI: Add driver for Intel Volume Management Device (VMD)
PCI/AER: Use 32 bit PCI domain numbers
x86/PCI: Allow DMA ops specific to a PCI domain
irqdomain: Export irq_domain_set_info() for module use
PCI: host: Add of_pci_get_host_bridge_resources() stub
genirq/MSI: Relax msi_domain_alloc() to support parentless MSI irqdomains
PCI: rcar: Add Gen2 PHY setup to pcie-rcar
PCI: rcar: Add runtime PM support to pcie-rcar
PCI: designware: Make config accessor override checking symmetric
PCI: ibmphp: Remove unneeded NULL test
ARM: dts: ifc6410: enable PCIe DT node for this board
ARM: dts: apq8064: add PCIe devicetree node
PCI: hotplug: Use list_for_each_entry() to simplify code
PCI: rcar: Remove unused pci_sys_data struct from pcie-rcar
PCI: hisi: Add support for HiSilicon Hip06 PCIe host controllers
PCI: Avoid iterating through memory outside the resource window
PCI: acpiphp_ibm: Fix null dereferences on null ibm_slot
...
|
|
Export irq_domain_set_info() for module use. It will be used by the Volume
Management Device driver.
[bhelgaas: changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull another round of GIC changes from Marc:
ACPI support for GIV-v2m
|
|
Since there will be several places checking if fwnode.type
is equal FWNODE_IRQCHIP, this patch adds a convenient function
for this purpose.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The Linux kernel already has the concept of IRQ domain, wherein a
component can expose a set of IRQs which are managed by a particular
interrupt controller chip or other subsystem. The PCI driver exposes
the notion of an IRQ domain for Message-Signaled Interrupts (MSI) from
PCI Express devices. This patch exposes the functions which are
necessary for creating a MSI IRQ domain within a module.
[ tglx: Split it into x86 and core irq parts ]
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Cc: gregkh@linuxfoundation.org
Cc: kys@microsoft.com
Cc: devel@linuxdriverproject.org
Cc: olaf@aepfle.de
Cc: apw@canonical.com
Cc: vkuznets@redhat.com
Cc: haiyangz@microsoft.com
Cc: marc.zyngier@arm.com
Cc: bhelgaas@google.com
Link: http://lkml.kernel.org/r/1449769983-12948-4-git-send-email-jakeo@microsoft.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We are soon going to need the MSI layer to call into the domain
allocators. Instead of open coding this, make the standard
irq_domain_alloc_irqs_recursive function available to the MSI
layer.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
As we're about to start converting the various MSI layers to
use fwnode_handle instead of device_node, add irq_domain_create_hierarchy
as a directly equivalent of irq_domain_add_hierarchy (which still
exists as a compatibility interface).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-16-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In order to be able to reference an irqdomain from ACPI, we need
to be able to create an identifier, which is usually a struct
device_node.
This device node does't really fit the ACPI infrastructure, so
we cunningly allocate a new structure containing a fwnode_handle,
and return that.
This structure doesn't really point to a device (interrupt
controllers are not "real" devices in Linux), but as we cannot
really deny that they exist, we create them with a new fwnode_type
(FWNODE_IRQCHIP).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-9-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Just like we have irq_domain_add_{linear,tree} to create a irq domain
identified by an of_node, introduce irq_domain_create_{linear,tree}
that do the same thing, except that they take a struct fwnode_handle.
Existing functions get rewritten in terms of the new ones so that
everything keeps working as before (and __irq_domain_add is now
fwnode_handle based as well).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-8-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Just like we have irq_create_of_mapping, irq_create_fwspec_mapping
creates a IRQ domain mapping for an interrupt described in a
struct irq_fwspec.
irq_create_of_mapping gets rewritten in terms of the new function,
and the hack we introduced before gets removed (now that no stacked
irqchip uses of_phandle_args anymore).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-7-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
So far the closest thing to a generic IRQ specifier structure is
of_phandle_args, which happens to be pretty OF specific (the of_node
pointer in there is quite annoying).
Let's introduce 'struct irq_fwspec' that can be used in place of
of_phandle_args for OF, but also for other firmware implementations
(that'd be ACPI). This is used together with a new 'translate' method
that is the pendent of 'xlate'.
We convert irq_create_of_mapping to use this new structure (with a
small hack that will be removed later).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
So far, our irq domains are still looked up by device node.
Let's change this and allow a domain to be looked up using
a fwnode_handle pointer.
The existing interfaces are preserved with a couple of helpers.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Now that we have everyone accessing the of_node field via the
irq_domain_get_of_node accessor, it is pretty easy to swap it
for a pointer to a fwnode_handle.
This translates into a few limited changes in __irq_domain_add,
and an updated irq_domain_get_of_node.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The struct irq_domain contains a "struct device_node *" field
(of_node) that is almost the only link between the irqdomain
and the device tree infrastructure.
In order to prepare for the removal of that field, convert all
users to use irq_domain_get_of_node() instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
NUMA node information is per-irq instead of per-irqchip, so move it into
struct irq_common_data. Also use CONFIG_NUMA to guard irq_common_data.node.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/1433145945-789-8-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
It is not uncommon (at least with the ARM stuff) to have a piece
of hardware that implements different flavours of "interrupts".
A typical example of this is the GICv3 ITS, which implements
standard PCI/MSI support, but also some form of "generic MSI".
So far, the PCI/MSI domain is registered using the ITS device_node,
so that irq_find_host can return it. On the contrary, the raw MSI
domain is not registered with an device_node, making it impossible
to be looked up by another subsystem (obviously, using the same
device_node twice would only result in confusion, as it is not
defined which one irq_find_host would return).
A solution to this is to "type" domains that may be aliasing, and
to be able to lookup an device_node that matches a given type.
For this, we introduce irq_find_matching_host() as a superset
of irq_find_host:
struct irq_domain *irq_find_matching_host(struct device_node *node,
enum irq_domain_bus_token bus_token);
where bus_token is the "type" we want to match the domain against
(so far, only DOMAIN_BUS_ANY is defined). This result in some
moderately invasive changes on the PPC side (which is the only
user of the .match method).
This has otherwise no functionnal change.
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Get the infrastructure patches which are required for x86/apic into core
|
|
Introduce helper function irq_data_get_node() and variants thereof to
hide struct irq_data implementation details.
Convert the core code to use them.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/1433145945-789-5-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
With the introduction of hierarchy irqdomain, struct irq_data becomes
per-chip instead of per-irq and there may be multiple irq_datas
associated with the same irq. Some per-irq data stored in struct
irq_data now may get duplicated into multiple irq_datas, and causes
inconsistent view.
So introduce struct irq_common_data to host per-irq common data and to
achieve consistent view among irq_chips.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1433145945-789-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This adds the helper irq_domain_set_info() in a non-domain hierarchy
variant. This allows to use the helper for generic chip since not
all chips using generic chip support domain hierarchy.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: marc.zyngier@arm.com
Cc: linux@arm.linux.org.uk
Cc: u.kleine-koenig@pengutronix.de
Cc: olof@lixom.net
Cc: arnd@arndb.de
Cc: daniel.lezcano@linaro.org
Cc: mark.rutland@arm.com
Cc: pawel.moll@arm.com
Cc: robh+dt@kernel.org
Cc: ijc+devicetree@hellion.org.uk
Cc: galak@codeaurora.org
Cc: mcoquelin.stm32@gmail.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: shawn.guo@linaro.org
Cc: kernel@pengutronix.de
Cc: jason@lakedaemon.net
Link: http://lkml.kernel.org/r/1431769465-26867-2-git-send-email-stefan@agner.ch
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Introduce helper function irq_domain_add_hierarchy(), which creates
a linear irqdomain if parameter 'size' is not zero, otherwise creates
a tree irqdomain.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: http://lkml.kernel.org/r/1416061447-9472-5-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Add a flags to irq_domain.flags to control whether the irqdomain core
should automatically call parent irqdomain's alloc/free callbacks. It
help to reduce hierarchy irqdomains users' code size.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: http://lkml.kernel.org/r/1416061447-9472-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
It is possible to call irq_create_of_mapping to create/translate the
same IRQ from DT for multiple times. Perform irq_find_mapping check
and set_type for hierarchy irqdomain in irq_create_of_mapping() to
avoid duplicate these functionality in all outer most irqdomain.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We plan to use hierarchy irqdomain to suppport CPU vector assignment,
interrupt remapping controller, IO-APIC controller, MSI interrupt
and hypertransport interrupt etc on x86 platforms. So extend irqdomain
interfaces to support hierarchy irqdomain.
There are already many clients of current irqdomain interfaces.
To minimize the changes, we choose to introduce new version 2 interfaces
to support hierarchy instead of extending existing irqdomain interfaces.
According to Thomas's suggestion, the most important design decision is
to build hierarchy struct irq_data to support hierarchy irqdomain, so
hierarchy irqdomain related data could be saved in struct irq_data.
With support of hierarchy irq_data, we could also support stacked
irq_chips. This is most useful in case of set_affinity().
The new hierarchy irqdomain introduces following interfaces:
1) irq_domain_alloc_irqs()/irq_domain_free_irqs(): allocate/release IRQ
and related resources.
2) __irq_domain_alloc_irqs(): a special version to support legacy IRQs.
3) irq_domain_activate_irq()/irq_domain_deactivate_irq(): program
interrupt controllers to activate/deactivate interrupt.
There are also several help functions to ease irqdomain implemenations:
1) irq_domain_get_irq_data(): get irq_data associated with a specific
irqdomain.
2) irq_domain_set_hwirq_and_chip(): save irqdomain specific data into
irq_data.
3) irq_domain_alloc_irqs_parent()/irq_domain_free_irqs_parent(): invoke
parent irqdomain's alloc/free callbacks.
We also changed irq_startup()/irq_shutdown() to invoke
irq_domain_activate_irq()/irq_domain_deactivate_irq() to program
interrupt controller when start/stop interrupts.
[ tglx: Folded parts of the later patch series in ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Export irq_domain_disassociate() to architecture interrupt drivers,
so it could be used to handle legacy IRQ descriptors on x86.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1402302011-23642-37-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Jiri Kosina <trivial@kernel.org>
Link: http://lkml.kernel.org/r/1401178092-1228-3-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Include appropriate header file include/linux/of_irq.h in
kernel/irq/irqdomain.c because it contains prototype definition of
function define in kernel/irq/irqdomain.c.
This eliminates the following warning in kernel/irq/irqdomain.c:
kernel/irq/irqdomain.c:468:14: warning: no previous prototype for ‘irq_create_of_mapping’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: http://lkml.kernel.org/r/eb89aebea7ff1a46122918ac389ebecf8248be9a.1393493276.git.rashika.kheria@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
All the callers of irq_create_of_mapping() pass the contents of a struct
of_phandle_args structure to the function. Since all the callers already
have an of_phandle_args pointer, why not pass it directly to
irq_create_of_mapping()?
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
|