| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Device node major/minor numbers are just stored in the payload of a single
data node. Just extend that to 4 bytes and use new_encode_dev() for it.
We only use the 4-byte format if we _need_ to, if !old_valid_dev(foo).
This preserves backwards compatibility with older code as much as
possible. If we do make devices with major or minor numbers above 255, and
then mount the file system with the old code, it'll just read the first
two bytes and get the numbers wrong. If it comes to garbage-collect it,
it'll then write back those wrong numbers. But that's about the best we
can expect.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
|
|
We have to pack at least the jint16_t structure, because otherwise it'll
be four bytes in size. Thankfully, we can do that and _not_ pack the
actual node structures, and the compiler still doesn't emit stupid code.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
can_share_swap_page() is used to check if the page has the last reference.
This avoids allocating a new page for COW if it's the last page.
However, if CONFIG_SWAP is not set, can_share_swap_page() is defined as 0,
thus always causes a copy for the last COW page. The below simple patch
fixes it.
Signed-off-by: Hua Zhong <hzhong@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
slab_is_available() indicates slab based allocators are available for use.
SPARSEMEM code needs to know this as it can be called at various times
during the boot process.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Even since a previous patch:
Fix race between CONFIG_DEBUG_SLABALLOC and modules
Sun, 27 Jun 2004 17:55:19 +0000 (17:55 +0000)
http://www.kernel.org/git/?p=linux/kernel/git/torvalds/old-2.6-bkcvs.git;a=commit;h=92b3db26d31cf21b70e3c1eadc56c179506d8fbe
The function symbol_put_addr() will deadlock the kernel.
symbol_put_addr() would acquire modlist_lock, then while holding the lock call
two functions kernel_text_address() and module_text_address() which also try
to acquire the same lock. This deadlocks the kernel of course.
This patch changes symbol_put_addr() to not acquire the modlist_lock, it
doesn't need it since it never looks at the module list directly. Also, it
now uses core_kernel_text() instead of kernel_text_address(). The latter has
an additional check for addr inside a module, but we don't need to do that
since we call module_text_address() (the same function kernel_text_address
uses) ourselves.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Cc: Zwane Mwaikambo <zwane@fsmlabs.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add new vmsplice system call and add missing __NR_xxx defines for
sys_set_robust_list, sys_get_robust_list, sys_splice, sys_sync_file_range
and sys_tee.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With "Paul E. McKenney" <paulmck@us.ibm.com>
Introduce rcu_needs_cpu() interface. This can be used to tell if there
will be a new rcu batch on a cpu soon by looking at the curlist pointer.
This can be used to avoid to enter a tickless idle state where the cpu
would miss that a new batch is ready when rcu_start_batch would be called
on a different cpu.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If we use __attribute__((packed)), GCC will _also_ assume that the
structures aren't sensibly aligned, and it'll emit code to cope with
that instead of straight word load/save. This can be _very_ suboptimal
on architectures like ARM.
Ideally, we want an attribute which just tells GCC not to do any
padding, without the alignment side-effects. In the absense of that,
we'll just drop the 'packed' attribute and hope that everything stays as
it was (which to be fair is fairly much what we expect). And add some
paranoia checks in the initialisation code, which should be optimised
away completely in the normal case.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
... and also fix the multiple inclusion guard so it actually _works_
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This attached patches provide xattr support including POSIX-ACL and
SELinux support on JFFS2 (version.5).
There are some significant differences from previous version posted
at last December.
The biggest change is addition of EBS(Erase Block Summary) support.
Currently, both kernel and usermode utility (sumtool) can recognize
xattr nodes which have JFFS2_NODETYPE_XATTR/_XREF nodetype.
In addition, some bugs are fixed.
- A potential race condition was fixed.
- Unexpected fail when updating a xattr by same name/value pair was fixed.
- A bug when removing xattr name/value pair was fixed.
The fundamental structures (such as using two new nodetypes and exclusion
mechanism by rwsem) are unchanged. But most of implementation were reviewed
and updated if necessary.
Espacially, we had to change several internal implementations related to
load_xattr_datum() to avoid a potential race condition.
[1/2] xattr_on_jffs2.kernel.version-5.patch
[2/2] xattr_on_jffs2.utils.version-5.patch
Signed-off-by: KaiGai Kohei <kaigai@ak.jp.nec.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
The classical IP over ATM code maintains its own IPv4 <-> <ATM stuff>
ARP table, using the standard neighbour-table code. The
neigh_table_init function adds this neighbour table to a linked list
of all neighbor tables which is used by the functions neigh_delete()
neigh_add() and neightbl_set(), all called by the netlink code.
Once the ATM neighbour table is added to the list, there are two
tables with family == AF_INET there, and ARP entries sent via netlink
go into the first table with matching family. This is indeterminate
and often wrong.
To see the bug, on a kernel with CLIP enabled, create a standard IPv4
ARP entry by pinging an unused address on a local subnet. Then attempt
to complete that entry by doing
ip neigh replace <ip address> lladdr <some mac address> nud reachable
Looking at the ARP tables by using
ip neigh show
will reveal two ARP entries for the same address. One of these can be
found in /proc/net/arp, and the other in /proc/net/atm/arp.
This patch adds a new function, neigh_table_init_no_netlink() which
does everything the neigh_table_init() does, except add the table to
the netlink all-arp-tables chain. In addition neigh_table_init() has a
check that all tables on the chain have a distinct address family.
The init call in clip.c is changed to call
neigh_table_init_no_netlink().
Since ATM ARP tables are rather more complicated than can currently be
handled by the available rtattrs in the netlink protocol, no
functionality is lost by this patch, and non-ATM ARP manipulation via
netlink is rescued. A more complete solution would involve a rtattr
for ATM ARP entries and some way for the netlink code to give
neigh_add and friends more information than just address family with
which to find the correct ARP table.
[ I've changed the assertion checking in neigh_table_init() to not
use BUG_ON() while holding neigh_tbl_lock. Instead we remember that
we found an existing tbl with the same family, and after dropping
the lock we'll give a diagnostic kernel log message and a stack dump.
-DaveM ]
Signed-off-by: Simon Kelley <simon@thekelleys.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One Block of the NAND Flash Array memory is reserved as
a One-Time Programmable Block memory area.
Also, 1st Block of NAND Flash Array can be used as OTP.
The OTP block can be read, programmed and locked using the same
operations as any other NAND Flash Array memory block.
OTP block cannot be erased.
OTP block is fully-guaranteed to be a valid block.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] 8250: add locking to console write function
[SERIAL] Remove unconditional enable of TX irq for console
[SERIAL] 8250: set divisor register correctly for AMD Alchemy SoC uart
[SERIAL] AMD Alchemy UART: claim memory range
[SERIAL] Clean up serial locking when obtaining a reference to a port
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET_SCHED]: HFSC: fix thinko in hfsc_adjust_levels()
[IPV6]: skb leakage in inet6_csk_xmit
[BRIDGE]: Do sysfs registration inside rtnl.
[NET]: Do sysfs registration as part of register_netdevice.
[TG3]: Fix possible NULL deref in tg3_run_loopback().
[NET] linkwatch: Handle jiffies wrap-around
[IRDA]: Switching to a workqueue for the SIR work
[IRDA]: smsc-ircc: Minimal hotplug support.
[IRDA]: Removing unused EXPORT_SYMBOLs
[IRDA]: New maintainer.
[NET]: Make netdev_chain a raw notifier.
[IPV4]: ip_options_fragment() has no effect on fragmentation
[NET]: Add missing operstates documentation.
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (25 commits)
[SCSI] mptfc: race between mptfc_register_dev and mptfc_target_alloc
[SCSI] lpfc 8.1.6 : Fix Data Corruption in Bus Reset Path
[SCSI] mptspi: revalidate negotiation parameters after host reset and resume
[SCSI] srp.h: avoid padding of structs
[SCSI] ibmvscsi: fix leak when failing to send srp event
[SCSI] qla2xxx: Correct eh_abort recovery logic.
[SCSI] megaraid_{mm,mbox}: fix a bug in reset handler
[SCSI] fusion - bug fix stack overflow in mptbase
[SCSI] scsi: Add IBM 2104-DU3 to blist
[SCSI] Fix DVD burning issues.
[SCSI] SCSI: aic7xxx_osm_pci resource leak fix.
[SCSI] - fusion - mptfc bug fix's to prevent deadlock situations
[SCSI] mptfusion: bug fix's for raid components adding/deleting
[SCSI] aic7xxx: ahc_pci_write_config() fix
[SCSI] megaraid: unused variable
[SCSI] qla2xxx: only free_irq() after request_irq() succeeds
[SCSI] Overrun in drivers/scsi/sim710.c
[SCSI] lpfc 8.1.5 : Change version number to 8.1.5
[SCSI] lpfc 8.1.5 : Misc small fixes
[SCSI] lpfc 8.1.5 : Additional fixes to LOGO, PLOGI, and RSCN processing
...
|
|
master.kernel.org:/pub/scm/linux/kernel/git/shemminger/netdev-2.6
* 'upstream' of master.kernel.org:/pub/scm/linux/kernel/git/shemminger/netdev-2.6:
sis900: phy for FoxCon motherboard
dl2k: use DMA_48BIT_MASK constant
phy: mdiobus_register(): initialize all phy_map entries
sky2: ifdown kills irq mask
|
|
Typo will be harder with this one.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
|
|
The last step of netdevice registration was being done by a delayed
call, but because it was delayed, it was impossible to return any error
code if the class_device registration failed.
Side effects:
* one state in registration process is unnecessary.
* register_netdevice can sleep inside class_device registration/hotplug
* code in netdev_run_todo only does unregistration so it is simpler.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/netdev-2.6
* 'upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/netdev-2.6:
[PATCH] bcm43xx: Fix access to non-existent PHY registers
[PATCH] bcm43xx: Fix array overrun in bcm43xx_geo_init
[PATCH] bcm43xx: check for valid MAC address in SPROM
[PATCH] ieee80211: Fix A band channel count (resent)
[PATCH] bcm43xx: fix iwmode crash when down
[PATCH] softmac: make non-operational after being stopped
[PATCH] softmac: don't reassociate if user asked for deauthentication
spidernet: enable support for bcm5461 ethernet phy
spidernet: introduce new setting
Fix RTL8019AS init for Toshiba RBTX49xx boards
au1000_eth.c: use ether_crc() from <linux/crc32.h>
sky2: version 1.3
Add more support for the Yukon Ultra chip found in dual core centino laptops.
sky2: synchronize irq on remove
sky2: dont write status ring
sky2: edge triggered workaround enhancement
sky2: use mask instead of modulo operation
sky2: tx ring index mask fix
sky2: status irq hang fix
sky2: backout NAPI reschedule
|
|
My commit 6bfd93c32a5065d0e858780b3beb0b667081601c broke the ARCH=ppc
compilation by using the is_kernel_addr() macro in asm/uaccess.h.
This fixes it by defining a suitable is_kernel_addr() for ARCH=ppc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
This is a backout of earlier patch.
The whole rescheduling hack was a bad idea. It doesn't really solve
the problem and it makes the code more complicated for no good reason.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
|
|
This was already a bad plan when I argued against adding it in the first
place. Good riddance.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Based on analysis&patch from Robert Hentosch
Observed on a Dell PE6850 with 16GB
The problem occurs very early on, when the kernel allocates space for the
temporary memory map called bootmap. The bootmap overlaps the EBDA region.
EBDA region is not historically reserved in the e820 mapping. When the
bootmap is freed it marks the EBDA region as usable.
If you notice in setup.c there is already code to work around the EBDA
in reserve_ebda_region(), this check however occurs after the bootmap
is allocated and doesn't prevent the bootmap from using this range.
AK: I redid the original patch. Thanks also to Jan Beulich for
spotting some mistakes.
Cc: Robert_Hentosch@dell.com
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The patch addresses a problem with ACPI SCI interrupt entry, which gets
re-used, and the IRQ is assigned to another unrelated device. The patch
corrects the code such that SCI IRQ is skipped and duplicate entry is
avoided. Second issue came up with VIA chipset, the problem was caused by
original patch assigning IRQs starting 16 and up. The VIA chipset uses
4-bit IRQ register for internal interrupt routing, and therefore cannot
handle IRQ numbers assigned to its devices. The patch corrects this
problem by allowing PCI IRQs below 16.
Cc: len.brown@intel.com
Signed-off by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] remove asm-ia64/bitops.h self-inclusion
[IA64] strcpy returns NULL pointer and not destination pointer
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IRDA] irda-usb: use NULL instead of 0
[IPV4]: Remove likely in ip_rcv_finish()
[NET]: Create netdev attribute_groups with class_device_add
[CLASS DEVICE]: add attribute_group creation
|
|
Patch from Bellido Nicolas
Include hardware.h in debug-macro.S, otherwise io_p2v is undefined.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Bellido Nicolas
Since git commit 2b78838842346da390e8547cd37035184376d506, entry-macro.S needs to include asm/arch/irqs.h
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Sascha Hauer
This patch fixes the addruart macro to work with both mmu enabled and
disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
After dwmw2 let me know it ought to be done, I rewrote the physmap map
driver to be a platform driver. I know zilch about the driver model,
so I probably botched it in some way, but I've done some tests on an
ixp23xx board which uses physmap, and it all seems to work.
In order to not break existing physmap users, I've added some compat
code that will instantiate a platform device iff CONFIG_MTD_PHYSMAP_LEN
is defined and != 0. Also, I've changed the default value for
CONFIG_MTD_PHYSMAP_LEN to zero, so that people who inadvertently
compile in physmap (or new, platform-style, users of physmap) don't get
burned.
This works pretty well -- the new physmap driver is a drop-in replacement
for the old one, and works on said ixp23xx board without any code changes
needed. (This should hold as long as users don't touch 'physmap_map'
directly.)
Once all physmap users have been converted to instantiate their own
platform devices, the compat code can go. (Or we decide that we can
change all the in-tree users at the same time, and never merge the
compat code.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Atomically create attributes when class device is added. This avoids
the race between registering class_device (which generates hotplug
event), and the creation of attribute groups.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the support of attribute groups in class_device's to allow
groups to be created as part of the registration process. This allows
network device's to avoid race between registration and creating
groups.
Note that unlike attributes that are a property of the class object,
the groups are a property of the class_device object. This is done
because there are different types of network devices (wireless for
example).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a deadlock situation in the receive path by allowing
temporary spillover of the receive buffer.
- If the chunk we receive has a tsn that immediately follows the ctsn,
accept it even if we run out of receive buffer space and renege data with
higher TSNs.
- Once we accept one chunk in a packet, accept all the remaining chunks
even if we run out of receive buffer space.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Mark Butler <butlerm@middle.net>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch from Nicolas Pitre
... but only for user space.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Nicolas Pitre
Intel PXA27x developers manual section 5.4.1.1 lists a priority
distribution for the DMA channels differently than what the code
currently assumes. This patch fixes that.
Noticed by Simon Vogl <vogl@soft.uni-linz.ac.at>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The channel count for 802.11a is still not right. We better
compute it from the min and max channel numbers, rather than
hardcoding it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
zd1211 with softmac and wpa_supplicant revealed an issue with softmac
and the use of workqueues. Some of the work functions actually
reschedule themselves, so this meant that there could still be
pending work after flush_scheduled_work() had been called during
ieee80211softmac_stop().
This patch introduces a "running" flag which is used to ensure that
rescheduling does not happen in this situation.
I also used this flag to ensure that softmac's hooks into ieee80211 are
non-operational once the stop operation has been started. This simply
makes softmac a little more robust, because I could crash it easily
by receiving frames in the short timeframe after shutting down softmac
and before turning off the ZD1211 radio. (ZD1211 is now fixed as well!)
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
asm-ia64/bitops.h includes itself. The #ifndef _ASM_IA64_BITOPS_H
prevents this from being an issue, but it should still be removed.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Patch from Nicolas Pitre
... for the definition of NULL.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] powerpc: Use the ibm,pa-features property if available
powerpc: Fix incorrect might_sleep in __get_user/__put_user on kernel addresses
[PATCH] ppc32 CPM_UART: fixes and improvements
[PATCH] ppc32 CPM_UART: Fixed break send on SCC
[PATCH] powerpc/kprobes: fix singlestep out-of-line
[PATCH] powerpc/pseries: avoid crash in PCI code if mem system not up
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3490/1: i.MX: move uart resources to board files
[ARM] 3488/1: make icedcc_putc do the right thing
[ARM] 3487/1: IXP4xx: Support non-PCI systems
[ARM] 3486/1: Mark memory as clobbered by the ARM _syscallX() macros
|
|
* master.kernel.org:/home/rmk/linux-2.6-mmc:
[MMC] Move set_ios debugging into mmc.c
[MMC] Correct mmc_request_done comments
[MMC] PXA: reduce the number of lines PXAMCI debug uses
[MMC] PXA and i.MX: don't avoid sending stop command on error
[MMC] extend data timeout for writes
[ARM] 3485/1: i.MX: MX1 SD/MMC fix of unintentional double start possibility
|
|
* 'splice' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] compat_sys_vmsplice: one-off in UIO_MAXIOV check
[PATCH] splice: redo page lookup if add_to_page_cache() returns -EEXIST
[PATCH] splice: rename remaining info variables to pipe
[PATCH] splice: LRU fixups
[PATCH] splice: fix unlocking of page on error ->prepare_write()
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[DECNET]: Fix level1 router hello
[TCP]: Fix sock_orphan dead lock
[ROSE]: Eleminate HZ from ROSE kernel interfaces
[NETROM]: Eleminate HZ from NET/ROM kernel interfaces
[AX.25]: Eleminate HZ from AX.25 kernel interfaces
[ROSE]: Fix routing table locking in rose_remove_neigh.
[AX.25]: Move AX.25 symbol exports
[HAMRADIO]: Remove remaining SET_MODULE_OWNER calls from hamradio drivers.
[AX25, ROSE]: Remove useless SET_MODULE_OWNER calls.
[AX.25]: Spelling fix
[ROSE]: Remove useless prototype for rose_remove_neigh().
[NETFILTER]: x_tables: don't use __copy_{from,to}_user on unchecked memory in compat layer
[NETFILTER]: H.323 helper: Change author's email address
[NETFILTER]: NAT: silence unused variable warnings with CONFIG_XFRM=n
[NETFILTER]: H.323 helper: fix use of uninitialized data
[NETFILTER]: H.323 helper: fix endless loop caused by invalid TPKT len
|
