| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull ARM fixes from Russell King:
"Most of this update are fixes primarily discovered from testing on the
older StrongARM 1110 and PXA systems, as a result of recent interest
from several people in these platforms:
- Locomo interrupt handling incorrectly stores the handler data in
the chip's private data slot: when Locomo is combined with an
interrupt controller who's chip uses the chip private data, this
leads to an oops.
- SA1111 was missing a call to clk_disable() to clean up after a
failed probe.
- SA1111 and PCMCIA suspend/resume was broken:
The PCMCIA "ds" layer was using the legacy bus suspend/resume
methods, which the core PM code is no longer calling as a result of
device_pm_check_callbacks() introduced in commit aa8e54b559479
("PM / sleep: Go direct_complete if driver has no callbacks").
SA1111 was broken due to changes to PCMCIA which makes PCMCIA
suspend itself later than the SA1111 code expects, and resume
before the SA1111 code has initialised access to the pcmcia
sub-device.
- the default SA1111 interrupt mask polarity got messed up when it
was converted to use a dynamic interrupt base number for its
interrupts.
- fix platform_get_irq() error code propagation, which was causing
problems on platforms where the interrupt may not be available at
probe time in DT setups.
- fix the lack of clock to PCMCIA code on PXA platforms, which was
omitted in conversions of PXA to CCF.
- fix an oops in the PXA PCMCIA code caused by a previous commit not
realising that Lubbock is different from the rest of the PXA PCMCIA
drivers.
- ensure that SA1111 low-level PCMCIA drivers propagate their error
codes to the main probe function, rather than the driver silently
accepting a failure.
- fix the sa11xx debugfs reporting of timing information, which
always indicated zero due to the clock being a factor of 1000 out.
- fix the polarity of the status change signal reported from the
sockets.
Lastly, one ARM specific commit from Stefan Agner fixing the LPAE
cache attributes"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: pxa/lubbock: add pcmcia clock
ARM: locomo: fix locomo irq handling
ARM: 8612/1: LPAE: initialize cache policy correctly
ARM: sa1111: fix missing clk_disable()
ARM: sa1111: fix pcmcia suspend/resume
ARM: sa1111: fix pcmcia interrupt mask polarity
ARM: sa1111: fix error code propagation in sa1111_probe()
pcmcia: lubbock: fix sockets configuration
pcmcia: sa1111: fix propagation of lowlevel board init return code
pcmcia: soc_common: fix SS_STSCHG polarity
pcmcia: sa11xx_base: add units to the timing information
pcmcia: sa11xx_base: fix reporting of timing information
pcmcia: ds: fix suspend/resume
|
|
Pull block fixes from Jens Axboe:
"A set of fixes for the current series in the realm of block.
Like the previous pull request, the meat of it are fixes for the nvme
fabrics/target code. Outside of that, just one fix from Gabriel for
not doing a queue suspend if we didn't get the admin queue setup in
the first place"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme-rdma: add back dependency on CONFIG_BLOCK
nvme-rdma: fix null pointer dereference on req->mr
nvme-rdma: use ib_client API to detect device removal
nvme-rdma: add DELETING queue flag
nvme/quirk: Add a delay before checking device ready for memblaze device
nvme: Don't suspend admin queue that wasn't created
nvme-rdma: destroy nvme queue rdma resources on connect failure
nvme_rdma: keep a ref on the ctrl during delete/flush
iw_cxgb4: block module unload until all ep resources are released
iw_cxgb4: call dev_put() on l2t allocation failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are two changes for v4.8. The first fixes a "[Firmware Bug]: reg
0x10: invalid BAR (can't size)" warning on Haswell, and the second
fixes a problem in some new runtime suspend functionality we merged
for v4.8. Summary:
Enumeration:
Mark Haswell Power Control Unit as having non-compliant BARs (Bjorn Helgaas)
Power management:
Fix bridge_d3 update on device removal (Lukas Wunner)"
* tag 'pci-v4.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Fix bridge_d3 update on device removal
PCI: Mark Haswell Power Control Unit as having non-compliant BARs
|
|
Starting with v4.8, we allow a PCIe port to runtime suspend to D3hot if the
port itself and its children satisfy a number of conditions. Once a child
is removed, we recheck those conditions in case the removed device was
blocking the port from suspending.
The rechecking needs to happen *after* the device has been removed from the
bus it resides on. Otherwise when walking the port's subordinate bus in
pci_bridge_d3_update(), the device being removed would erroneously still be
taken into account.
However the device is removed from the bus_list in pci_destroy_dev() and we
currently recheck *before* that. Fix it.
Fixes: 9d26d3a8f1b0 ("PCI: Put PCIe ports into D3 during suspend")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <mika.westerberg@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"This contains a Xen fix, an arm64 fix and a race condition /
robustization set of fixes related to ExitBootServices() usage and
boundary conditions"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Use efi_exit_boot_services()
efi/libstub: Use efi_exit_boot_services() in FDT
efi/libstub: Introduce ExitBootServices helper
efi/libstub: Allocate headspace in efi_get_memory_map()
efi: Fix handling error value in fdt_find_uefi_params
efi: Make for_each_efi_memory_desc_in_map() cope with running on Xen
|
|
Pull MD fixes from Shaohua Li:
"A few bug fixes for MD:
- Guoqing fixed a bug compiling md-cluster in kernel
- I fixed a potential deadlock in raid5-cache superblock write, a
hang in raid5 reshape resume and a race condition introduced in
rc4"
* tag 'md/4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
raid5: fix a small race condition
md-cluster: make md-cluster also can work when compiled into kernel
raid5: guarantee enough stripes to avoid reshape hang
raid5-cache: fix a deadlock in superblock write
|
|
for-linus
Sagi writes:
Here we have:
- Kconfig dependencies fix from Arnd
- nvme-rdma device removal fixes from Steve
- possible bad deref fix from Colin
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Some small fixes for the new sunxi clk driver introduced this merge
window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: Fix wrong reset register offsets
clk: sunxi-ng: nk: Make ccu_nk_find_best static
clk: sunxi-ng: Fix inverted test condition in ccu_helper_wait_for_lock
clk: sunxi: Fix return value check in sun8i_a23_mbus_setup()
clk: sunxi: pll2: Fix return value check in sun4i_pll2_setup()
|
|
A recent change removed the dependency on BLK_DEV_NVME, which implies
the dependency on PCI and BLOCK. We don't need CONFIG_PCI, but without
CONFIG_BLOCK we get tons of build errors, e.g.
In file included from drivers/nvme/host/core.c:16:0:
linux/blk-mq.h:182:33: error: 'struct gendisk' declared inside parameter list will not be visible outside of this definition or declaration [-Werror]
drivers/nvme/host/core.c: In function 'nvme_setup_rw':
drivers/nvme/host/core.c:295:21: error: implicit declaration of function 'rq_data_dir' [-Werror=implicit-function-declaration]
drivers/nvme/host/nvme.h: In function 'nvme_map_len':
drivers/nvme/host/nvme.h:217:6: error: implicit declaration of function 'req_op' [-Werror=implicit-function-declaration]
drivers/nvme/host/scsi.c: In function 'nvme_trans_bdev_limits_page':
drivers/nvme/host/scsi.c:768:85: error: implicit declaration of function 'queue_max_hw_sectors' [-Werror=implicit-function-declaration]
This adds back the specific CONFIG_BLOCK dependency to avoid broken
configurations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: aa71987472a9 ("nvme: fabrics drivers don't need the nvme-pci driver")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
If there is an error on req->mr, req->mr is set to null, however
the following statement sets req->mr->need_inval causing a null
pointer dereference. Fix this by bailing out to label 'out' to
immediately return and hence skip over the offending null pointer
dereference.
Fixes: f5b7b559e1488 ("nvme-rdma: Get rid of duplicate variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Change nvme-rdma to use the IB Client API to detect device removal.
This has the wonderful benefit of being able to blow away all the
ib/rdma_cm resources for the device being removed. No craziness about
not destroying the cm_id handling the event. No deadlocks due to broken
iw_cm/rdma_cm/iwarp dependencies. And no need to have a bound cm_id
around during controller recovery/reconnect to catch device removal
events.
We don't use the device_add aspect of the ib_client service since we only
want to create resources for an IB device if we have a target utilizing
that device.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
When we get a surprise disconnect from the target we queue a periodic
reconnect (which is the sane thing to do...).
We only move the queues out of CONNECTED when we retry to reconnect (after
10 seconds in the default case) but we stop the blk queues immediately
so we are not bothered with traffic from now on. If delete() is kicking
off in this period the queues are still in CONNECTED state.
Part of the delete sequence is trying to issue ctrl shutdown if the
admin queue is CONNECTED (which it is!). This request is issued but
stuck in blk-mq waiting for the queues to start again. This might be
the one preventing us from forward progress...
The patch separates the queue flags to CONNECTED and DELETING. Now we
will move out of CONNECTED as soon as error recovery kicks in (before
stopping the queues) and DELETING is on when we start the queue deletion.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Pull networking fixes from David Miller:
"Mostly small sets of driver fixes scattered all over the place.
1) Mediatek driver fixes from Sean Wang. Forward port not written
correctly during TX map, missed handling of EPROBE_DEFER, and
mistaken use of put_page() instead of skb_free_frag().
2) Fix socket double-free in KCM code, from WANG Cong.
3) QED driver fixes from Sudarsana Reddy Kalluru, including a fix for
using the dcbx buffers before initializing them.
4) Mellanox Switch driver fixes from Jiri Pirko, including a fix for
double fib removals and an error handling fix in
mlxsw_sp_module_init().
5) Fix kernel panic when enabling LLDP in i40e driver, from Dave
Ertman.
6) Fix padding of TSO packets in thunderx driver, from Sunil Goutham.
7) TCP's rcv_wup not initialized properly when using fastopen, from
Neal Cardwell.
8) Don't use uninitialized flow keys in flow dissector, from Gao
Feng.
9) Use after free in l2tp module unload, from Sabrina Dubroca.
10) Fix interrupt registry ordering issues in smsc911x driver, from
Jeremy Linton.
11) Fix crashes in bonding having to do with enslaving and rx_handler,
from Mahesh Bandewar.
12) AF_UNIX deadlock fixes from Linus.
13) In mlx5 driver, don't read skb->xmit_mode after it might have been
freed from the TX reclaim path. From Tariq Toukan.
14) Fix a bug from 2015 in TCP Yeah where the congestion window does
not increase, from Artem Germanov.
15) Don't pad frames on receive in NFP driver, from Jakub Kicinski.
16) Fix chunk fragmenting in SCTP wrt. GSO, from Marcelo Ricardo
Leitner.
17) Fix deletion of VRF routes, from Mark Tomlinson.
18) Fix device refcount leak when DAD fails in ipv6, from Wei Yongjun"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
net/mlx4_en: Fix panic on xmit while port is down
net/mlx4_en: Fixes for DCBX
net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_state()
net/mlx4_en: Fix the return value of mlx4_en_dcbnl_set_all()
net: ethernet: renesas: sh_eth: add POST registers for rz
drivers: net: phy: mdio-xgene: Add hardware dependency
dwc_eth_qos: do not register semi-initialized device
sctp: identify chunks that need to be fragmented at IP level
mlxsw: spectrum: Set port type before setting its address
mlxsw: spectrum_router: Fix error path in mlxsw_sp_router_init
nfp: don't pad frames on receive
nfp: drop support for old firmware ABIs
nfp: remove linux/version.h includes
tcp: cwnd does not increase in TCP YeAH
net/mlx5e: Fix parsing of vlan packets when updating lro header
net/mlx5e: Fix global PFC counters replication
net/mlx5e: Prevent casting overflow
net/mlx5e: Move an_disable_cap bit to a new position
net/mlx5e: Fix xmit_more counter race issue
tcp: fastopen: avoid negative sk_forward_alloc
...
|
|
On lubbock board, the probe of the driver crashes by dereferencing very
early a platform_data structure which is not set, in
pxa2xx_configure_sockets().
The stack fixed is :
[ 0.244353] SA1111 Microprocessor Companion Chip: silicon revision 1, metal revision 1
[ 0.256321] sa1111 sa1111: Providing IRQ336-390
[ 0.340899] clocksource: Switched to clocksource oscr0
[ 0.472263] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 0.480469] pgd = c0004000
[ 0.483432] [00000004] *pgd=00000000
[ 0.487105] Internal error: Oops: f5 [#1] ARM
[ 0.491497] Modules linked in:
[ 0.494650] CPU: 0 PID: 1 Comm: swapper Not tainted 4.8.0-rc3-00080-g1aaa68426f0c-dirty #2068
[ 0.503229] Hardware name: Intel DBPXA250 Development Platform (aka Lubbock)
[ 0.510344] task: c3e42000 task.stack: c3e44000
[ 0.514984] PC is at pxa2xx_configure_sockets+0x4/0x24 (drivers/pcmcia/pxa2xx_base.c:227)
[ 0.520193] LR is at pcmcia_lubbock_init+0x1c/0x38
[ 0.525079] pc : [<c0247c30>] lr : [<c02479b0>] psr: a0000053
[ 0.525079] sp : c3e45e70 ip : 100019ff fp : 00000000
[ 0.536651] r10: c0828900 r9 : c0434838 r8 : 00000000
[ 0.541953] r7 : c0820700 r6 : c0857b30 r5 : c3ec1400 r4 : c0820758
[ 0.548549] r3 : 00000000 r2 : 0000000c r1 : c3c09c40 r0 : c3ec1400
[ 0.555154] Flags: NzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
[ 0.562450] Control: 0000397f Table: a0004000 DAC: 00000053
[ 0.568257] Process swapper (pid: 1, stack limit = 0xc3e44190)
[ 0.574154] Stack: (0xc3e45e70 to 0xc3e46000)
[ 0.578610] 5e60: c4849800 00000000 c3ec1400 c024769c
[ 0.586928] 5e80: 00000000 c3ec140c c3c0ee0c c3ec1400 c3ec1434 c020c410 c3ec1400 c3ec1434
[ 0.595244] 5ea0: c0820700 c080b408 c0828900 c020c5f8 00000000 c0820700 c020c578 c020ac5c
[ 0.603560] 5ec0: c3e687cc c3e71e10 c0820700 00000000 c3c02de0 c020bae4 c03c62f7 c03c62f7
[ 0.611872] 5ee0: c3e68780 c0820700 c042e034 00000000 c043c440 c020cdec c080b408 00000005
[ 0.620188] 5f00: c042e034 c00096c0 c0034440 c01c730c 20000053 ffffffff 00000000 00000000
[ 0.628502] 5f20: 00000000 c3ffcb87 c3ffcb90 c00346ac c3e66ba0 c03f7914 00000092 00000005
[ 0.636811] 5f40: 00000005 c03f847c 00000091 c03f847c 00000000 00000005 c0434828 00000005
[ 0.645125] 5f60: c043482c 00000092 c043c440 c0828900 c0434838 c0418d2c 00000005 00000005
[ 0.653430] 5f80: 00000000 c041858c 00000000 c032e9f0 00000000 00000000 00000000 00000000
[ 0.661729] 5fa0: 00000000 c032e9f8 00000000 c000f0f0 00000000 00000000 00000000 00000000
[ 0.670020] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 0.678311] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[ 0.686673] (pxa2xx_configure_sockets) from pcmcia_lubbock_init (/drivers/pcmcia/sa1111_lubbock.c:161)
[ 0.696026] (pcmcia_lubbock_init) from pcmcia_probe (/drivers/pcmcia/sa1111_generic.c:213)
[ 0.704358] (pcmcia_probe) from driver_probe_device (/drivers/base/dd.c:378 /drivers/base/dd.c:499)
[ 0.712848] (driver_probe_device) from __driver_attach (/./include/linux/device.h:983 /drivers/base/dd.c:733)
[ 0.721414] (__driver_attach) from bus_for_each_dev (/drivers/base/bus.c:313)
[ 0.729723] (bus_for_each_dev) from bus_add_driver (/drivers/base/bus.c:708)
[ 0.738036] (bus_add_driver) from driver_register (/drivers/base/driver.c:169)
[ 0.746185] (driver_register) from do_one_initcall (/init/main.c:778)
[ 0.754561] (do_one_initcall) from kernel_init_freeable (/init/main.c:843 /init/main.c:851 /init/main.c:869 /init/main.c:1016)
[ 0.763409] (kernel_init_freeable) from kernel_init (/init/main.c:944)
[ 0.771660] (kernel_init) from ret_from_fork (/arch/arm/kernel/entry-common.S:119)
[ 0.779347] Code: c03c6305 c03c631e c03c632e e5903048 (e993000c)
All code
========
0: c03c6305 eorsgt r6, ip, r5, lsl #6
4: c03c631e eorsgt r6, ip, lr, lsl r3
8: c03c632e eorsgt r6, ip, lr, lsr #6
c: e5903048 ldr r3, [r0, #72] ; 0x48
10:* e993000c ldmib r3, {r2, r3} <-- trapping instruction
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
When testing Lubbock, it was noticed that the sa1111 pcmcia driver bound
but was not functional due to no sockets being registered. This is
because the return code from the lowlevel board initialisation was not
being propagated out of the probe function. Fix this.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
SS_STSCHG should be set for an IO card when the BVD1 signal is asserted
low, not high.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add units to the timing information, so we know that the numbers are
nanoseconds. The output changes from:
I/O : 165 (172)
attribute: 300 (316)
common : 300 (316)
to:
I/O : 165ns (172ns)
attribute: 300ns (316ns)
common : 300ns (316ns)
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Fix the reporting of the currently programmed timing information. These
entries have been showing zero due to the clock rate being a factor of
1000 too big. With this change, we go from:
I/O : 165 (0)
attribute: 300 (0)
common : 300 (0)
to:
I/O : 165 (172)
attribute: 300 (316)
common : 300 (316)
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
PCMCIA suspend/resume no longer works since the commit mentioned below,
as the callbacks are no longer made. Convert the driver to the new
dev_pm_ops, which restores the suspend/resume functionality. Tested on
the arm arch Assabet platform.
Fixes: aa8e54b559479 ("PM / sleep: Go direct_complete if driver has no callbacks")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
When port is down, tx drop counter update is not needed.
Updating the counter in this case can cause a kernel
panic as when the port is down, ring can be NULL.
Fixes: 63a664b7e92b ("net/mlx4_en: fix tx_dropped bug")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a capability check before enabling DCBX.
In addition, it re-organizes the relevant data structures,
and fixes a typo in a define.
Fixes: af7d51852631 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx4_en_dcbnl_set_state() returns u8, the return value from
mlx4_en_setup_tc() could be negative in case of failure, so fix that.
Fixes: af7d51852631 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx4_en_dcbnl_set_all() returns u8, so return value can't be negative in
case of failure.
Fixes: af7d51852631 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit aa71987472a9 ("nvme: fabrics drivers don't need the nvme-pci
driver") removed the dependency on BLK_DEV_NVME, but the cdoe does
depend on the block layer (which used to be an implicit dependency
through BLK_DEV_NVME).
Otherwise you get various errors from the kbuild test robot random
config testing when that happens to hit a configuration with BLOCK
device support disabled.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jay Freyensee <james_p_freyensee@linux.intel.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO fixes from Greg KH:
"Here are a few small IIO fixes for 4.8-rc6.
Nothing major, full details are in the shortlog, all of these have
been in linux-next with no reported issues"
* tag 'staging-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio:core: fix IIO_VAL_FRACTIONAL sign handling
iio: ensure ret is initialized to zero before entering do loop
iio: accel: kxsd9: Fix scaling bug
iio: accel: bmc150: reset chip at init time
iio: fix pressure data output unit in hid-sensor-attributes
tools:iio:iio_generic_buffer: fix trigger-less mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB gadget, phy, and xhci fixes for 4.8-rc6.
All of these resolve minor issues that have been reported, and all
have been in linux-next with no reported issues"
* tag 'usb-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: udc: fix NULL ptr dereference in isr_setup_status_phase
xhci: fix null pointer dereference in stop command timeout function
usb: dwc3: pci: fix build warning on !PM_SLEEP
usb: gadget: prevent potenial null pointer dereference on skb->len
usb: renesas_usbhs: fix clearing the {BRDY,BEMP}STS condition
usb: phy: phy-generic: Check clk_prepare_enable() error
usb: gadget: udc: renesas-usb3: clear VBOUT bit in DRD_CON
Revert "usb: dwc3: gadget: always decrement by 1"
|
|
Due to a mistake in the hardware manual, the FWSLC and POST1-4 registers
were not documented and left out of the driver for RZ/A making the CAM
feature non-operational.
Additionally, when the offset values for POST1-4 are left blank, the driver
attempts to set them using an offset of 0xFFFF which can cause a memory
corruption or panic.
This patch fixes the panic and properly enables CAM.
Reported-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"nvdimm fixes for v4.8, two of them are tagged for -stable:
- Fix devm_memremap_pages() to use track_pfn_insert(). Otherwise,
DAX pmd mappings end up with an uncached pgprot, and unusable
performance for the device-dax interface. The device-dax interface
appeared in 4.7 so this is tagged for -stable.
- Fix a couple VM_BUG_ON() checks in the show_smaps() path to
understand DAX pmd entries. This fix is tagged for -stable.
- Fix a mis-merge of the nfit machine-check handler to flip the
polarity of an if() to match the final version of the patch that
Vishal sent for 4.8-rc1. Without this the nfit machine check
handler never detects / inserts new 'badblocks' entries which
applications use to identify lost portions of files.
- For test purposes, fix the nvdimm_clear_poison() path to operate on
legacy / simulated nvdimm memory ranges. Without this fix a test
can set badblocks, but never clear them on these ranges.
- Fix the range checking done by dax_dev_pmd_fault(). This is not
tagged for -stable since this problem is mitigated by specifying
aligned resources at device-dax setup time.
These patches have appeared in a next release over the past week. The
recent rebase you can see in the timestamps was to drop an invalid fix
as identified by the updated device-dax unit tests [1]. The -mm
touches have an ack from Andrew"
[1]: "[ndctl PATCH 0/3] device-dax test for recent kernel bugs"
https://lists.01.org/pipermail/linux-nvdimm/2016-September/006855.html
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm: allow legacy (e820) pmem region to clear bad blocks
nfit, mce: Fix SPA matching logic in MCE handler
mm: fix cache mode of dax pmd mappings
mm: fix show_smap() for zone_device-pmd ranges
dax: fix mapping size check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Mostly driver bugfixes, but also a few cleanups which are nice to have
out of the way"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rk3x: Restore clock settings at resume time
i2c: Spelling s/acknowedge/acknowledge/
i2c: designware: save the preset value of DW_IC_SDA_HOLD
Documentation: i2c: slave-interface: add note for driver development
i2c: mux: demux-pinctrl: run properly with multiple instances
i2c: bcm-kona: fix inconsistent indenting
i2c: rcar: use proper device with dma_mapping_error
i2c: sh_mobile: use proper device with dma_mapping_error
i2c: mux: demux-pinctrl: invalidate properly when switching fails
|
|
The mdio-xgene driver is only useful on X-Gene SoC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Iyappan Subramanian <isubramanian@apm.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.8
iwlwifi
* fix P2P dump trigger
* prevent a potential null dereference in iwlmvm
* prevent an uninitialized value from being returned in iwlmvm
* advertise support for channel width change in AP mode
ath10k
* fix racy rx status retrieval from htt context
* QCA9887 support is not experimental anymore, remove the warning message
ath9k
* fix regression with led GPIOs
* fix AR5416 GPIO access warning
brcmfmac
* avoid potential stack overflow in brcmf_cfg80211_start_ap()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We move register_netdev() to the end of dwceqos_probe() to close any
races where the netdev callbacks are called before the initialization
has finished.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bad blocks can be injected via /sys/block/pmemN/badblocks. In a situation
where legacy pmem is being used or a pmem region created by using memmap
kernel parameter, the injected bad blocks are not cleared due to
nvdimm_clear_poison() failing from lack of ndctl function pointer. In
this case we need to just return as handled and allow the bad blocks to
be cleared rather than fail.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The check for a 'pmem' type SPA in the MCE handler was inverted due to a
merge/rebase error.
Fixes: 6839a6d nfit: do an ARS scrub on hitting a latent media error
Cc: linux-acpi@vger.kernel.org
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
During port init, we currently set the port's type to Ethernet after
setting its MAC address. However, the hardware documentation states this
should be the other way around.
Align the driver with the hardware documentation and set the port's MAC
address after setting its type.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When neigh_init fails, we have to do proper cleanup including
router_fini call.
Fixes: 6cf3c971dc84cb ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull virtio fixes from Michael Tsirkin:
"This includes a couple of bugfixs for virtio.
The virtio console patch is actually also in x86/tip targeting 4.9
because it helps vmap stacks, but it also fixes IOMMU_PLATFORM which
was added in 4.8, and it seems important not to ship that in a broken
configuration"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_console: Stop doing DMA on the stack
virtio: mark vring_dma_dev() static
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes that have been boiling the last two weeks or so.
Nothing special, I'm trying to sort out some Kconfig business and
Russell needs a fix in for -his SA1100 rework.
Summary:
- Revert a pointless attempt to add an include to solve the UM allyes
compilation problem.
- Make the mcp23s08 depend on OF_GPIO as it uses it and doesn't
compile properly without it.
- Fix a probing problem for ucb1x00"
* tag 'gpio-v4.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: sa1100: fix irq probing for ucb1x00
gpio: mcp23s08: make driver depend on OF_GPIO
Revert "gpio: include <linux/io-mapping.h> in gpiolib-of"
|
|
virtio_console uses a small DMA buffer for control requests. Move
that buffer into heap memory.
Doing virtio DMA on the stack is normally okay on non-DMA-API virtio
systems (which is currently most of them), but it breaks completely
if the stack is virtually mapped.
Tested by typing both directions using picocom aimed at /dev/hvc0.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
|
|
We get 1 warning when building kernel with W=1:
drivers/virtio/virtio_ring.c:170:16: warning: no previous prototype for 'vring_dma_dev' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
commit 5f9d1fde7d54a5(raid5: fix memory leak of bio integrity data)
moves bio_reset to bio_endio. But it introduces a small race condition.
It does bio_reset after raid5_release_stripe, which could make the
stripe reusable and hence reuse the bio just before bio_reset. Moving
bio_reset before raid5_release_stripe is called should fix the race.
Reported-and-tested-by: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.8-rc6
Unfortunately we have a bogus dwc3 patch leaked through the cracks and
got merged into Linus' HEAD. That patch ended up causing off-by-1 error
in our TRB accounting logic. Thankfully John Youn found out the problem
and we provided a revert to the bogus dwc3 patch in no time.
Apart from this off-by-1 error, we have two fixes to the Renesas drivers,
a small fix to our generic phy driver, a NULL pointer dereference fix for
f_eem and a build warning fix in dwc3.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Fix the possible kernel panic when the hardware signal is bad for chipidea udc.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.8 cycle.
We have a big rework of the kxsd9 driver queued up behind the fix below and
a fix for a recent fix that was marked for stable.
Hence this fix series is perhaps a little more urgent than average for IIO.
* core
- a fix for a fix in the last set. The recent fix for blocking ops when
! task running left a path (unlikely one) in which the function return
value was not set - so initialise it to 0.
- The IIO_TYPE_FRACTIONAL code previously didn't cope with negative
fractions. Turned out a fix for this was in Analog's tree but hadn't made
it upstream.
* bmc150
- reset chip at init time. At least one board out there ends up coming up
in an unstable state due to noise during power up. The reset does no
harm on other boards.
* kxsd9
- Fix a bug in the reported scaling due to failing to set the integer
part to 0.
* hid-sensors-pressure
- Output was in the wrong units to comply with the IIO ABI.
* tools
- iio_generic_buffer: Fix the trigger-less mode by ensuring we don't fault
out for having no trigger when we explicitly said we didn't want to have
one.
|
|
Problems with the signal integrity of the high speed USB data lines or
noise on reference ground lines can cause the i.MX6 USB controller to
violate USB specs and exhibit unexpected behavior.
It was observed that USBi_UI interrupts were triggered first and when
isr_setup_status_phase was called, ci->status was NULL, which lead to a
NULL pointer dereference kernel panic.
This patch fixes the kernel panic, emits a warning once and returns
-EPIPE to halt the device and let the host get stalled.
It also adds a comment to point people, who are experiencing this issue,
to their USB hardware design.
Cc: <stable@vger.kernel.org> #4.1+
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
There is no need to pad frames to ETH_ZLEN on RX.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Be more strict about FW versions. Drop support for old
transitional revisions which were never used in production.
Dropping support for FW ABI version 0.0.0.0 is particularly
useful because 0 could just be uninitialized memory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecessary version.h includes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently vlan tagged packets were not parsed correctly
and assumed to be regular IPv4/IPv6 packets.
We should check for 802.1Q/802.1ad tags and update the lro header
accordingly.
This fixes the use case where LRO is on and rxvlan is off
(vlan stripping is off).
Fixes: e586b3b0baee ('net/mlx5: Ethernet Datapath files')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when reading global PFC statistics we left the counter
iterator out of the equation and we ended up reading the same counter
over and over again.
Instead of reading the counter at index 0 on every iteration we now read
the counter at index (i).
Fixes: e989d5a532ce ('net/mlx5e: Expose flow control counters to ethtool')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
