| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Copyright, Trademark & Confidentiality legal statements throughout the
source code changed from LSI to Avago.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
timeouts at driver load time
When a flaky disk is there in a topology then during driver load,
discovery related I/O times out; which results in SCSI error recovery
initiating host reset and then the controller won't see any disk.
In this patch, The driver would return FAILED status to the host reset
initiated due to discovery related I/O timeout if ioc->is_driver_loading
is set. This flag would be set until we exit out of scsih_scan_finished().
i.e.
During device discovery if one of the disk is flaky
(which responds to some discovery commands and doesn't respond to some)
the driver wouldn't perform host reset for discovery related I/O timeout.
Instead it would return Failure for the host reset resulting in the
flaky disk getting removed by the SCSI Mid layer,
so other disks would be added correctly.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This patch will log a message when driver receives "Temperature Threshold
exceeded" event from any temperature sensor.
The message will look similar to like:
mpt3sas0: Temperature Threshold flags a b c d exceeded for Sensor: x !!!
mpt3sas0: Current Temp In Celsius: y
where a b c d are threshold flags 0 1 2 3
Change_set:
1. Get the number of sensor count of this IOC by reading IO Unit page 8 at
driver initialization time.
2. Also unmask the Temperature Threshold Event at driver initialization
time
3. Whenever a MPI2_EVENT_TEMP_THRESHOLD event is received from the
firmware, then print the sensor number, the maximum threshold number it
has exceed and the current temperature of this sensor.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete. The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Merge two functions, and remove overly verbose debugging output that pokes
into mid-layer internal structures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.
Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
|
|
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove the ordered_tags field, we haven't been issuing ordered tags based
on it since the big barrier rework in 2010.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Most drivers use exactly the same implementation, so provide it as a
library function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
In _scsih_probe, propagate the return value from scsi_add_host.
In mpt3sas, avoid calling list_del twice if that returns an
error, which causes list_del corruption warnings if an error
is returned.
Tested with blk-mq and scsi-mq patches to properly cleanup
from and propagate blk_mq_init_rq_map errors.
Signed-off-by: Robert Elliott <elliott@hp.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Copyright in driver sources is updated for year the 2014.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Added code to send an SEP message that turns off the Predictive
Failure LED when a drive is removed (if Predictive Failure LED was turned on).
Added a new flag 'pfa_led_on' per device that tracks the status of Predictive
Failure LED. When the drive is removed, this flag is checked and
sends an SEP message to turn off the respective Predictive Failure LED.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
In _scsih_probe, delay the call to scsi_add_host until the host has been
fully set up.
Otherwise, the default .can_queue value of 1 causes scsi-mq to set the block
layer request queue size to its minimum size, resulting in awful performance.
In _scsih_probe error handling, call mpt3sas_base_detach rather than
scsi_remove_host to properly clean up in reverse order.
In _scsih_remove, call scsi_remove_host earlier to clean up in reverse order.
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@avagotech.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Tack the firmware reply event_data payload to the end of its
corresponding struct fw_event_work allocation. This matches the
convention in the mptfusion driver and simplifies the code.
This avoids the following smatch warning:
drivers/scsi/mpt3sas/mpt3sas_scsih.c:2519
mpt3sas_send_trigger_data_event() warn: possible memory leak of
'fw_event'
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
In _scsih_{slave,target}_alloc, an incorrect structure type is passed
to sizeof() when allocating storage for hostdata. Luckily larger
structure types were used, so at least the wrong sizes were safe:
struct scsi_device (1784 bytes) > struct MPT3SAS_DEVICE (24 bytes)
struct scsi_target (760 bytes) > struct MPT3SAS_TARGET (32 bytes)
This fixes the following smatch warnings:
drivers/scsi/mpt3sas/mpt3sas_scsih.c:1166 _scsih_target_alloc()
warn: struct type mismatch 'MPT3SAS_TARGET vs scsi_target'
drivers/scsi/mpt3sas/mpt3sas_scsih.c:1280 _scsih_slave_alloc()
warn: struct type mismatch 'MPT3SAS_DEVICE vs scsi_device'
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Now that we're using 64-bit LUNs internally we need to increase
the size of max_luns to 64 bits, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Removing the host_lock from the I/O submission path gives a huge
scalability improvement.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Praveen Krishnamoorthy <Praveen.krishnamoorthy@lsi.com>
Acked-by: Sreekanth Reddy <Sreekanth.reddy@lsi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The mpt3sas_scsih_issue_tm() function does not use the 'serial_number'
argument passed to it. Removing it removes the last vestiges of the
scsi_cmnd's serial_number field from this driver.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Praveen Krishnamoorthy <Praveen.krishnamoorthy@lsi.com>
Acked-by: Sreekanth Reddy <Sreekanth.reddy@lsi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
If mpt3sas_base_map_resources takes an early error path then its
counterpart, mpt3sas_base_free_resources needs to be careful about
cleaning up:
1 - _base_mask_interrupts and _base_make_ioc_ready require memory
mapped I/O registers, make sure that this is true.
2 - _base_free_irq iterates over the adapter's reply_queue_list, so
move this list head initialization out of _base_enable_msix to
_scsih_probe so this will always be safe.
3 - check that the controller PCI device and its BARs have been
enabled before disabling them.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
are removed but their transport layer entries are not removed
When Async scanning mode is enabled and device scanning is in progress,
devices should not be removed. But in actuality, devices are removed but
their transport layer entries are not removed. This causes error to add
the same device to the transport layer after host reset or diagnostic
reset.
So, in this patch, modified the code in such a way that device is not removed
when Async scanning mode is enabled and device scanning is in progress.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
MPI2_IOCSTATUS_CONFIG_INVALID_PAGE is not returned
Infinite loop can occur if IOCStatus is not equal to
MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value in the while loops in functions
_scsih_search_responding_sas_devices,
_scsih_search_responding_raid_devices and
_scsih_search_responding_expanders
So, Instead of checking for MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value,
in this patch code is modified to check for IOCStatus not equals to
MPI2_IOCSTATUS_SUCCESS to break the while loop.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
non LUN 0 configured expander
With some enclosures when LUN 0 is not created but LUN 1 or LUN X is created
then SCSI scan procedure calls target_alloc, slave_alloc call back functions
for LUN 0 and slave_destory() for same LUN 0.
In these kind of cases within slave_destroy, pointer to scsi_target in
_sas_device structure is set to NULL, following which when slave_alloc for LUN
1 is called then starget would not be set properly for this LUN. So,
scsi_target pointer pointing to NULL value would lead to a crash later in the
discovery procedure.
To solve this issue set the sas_device's scsi_target pointer to scsi_device's
scsi_target if it is NULL earlier in slave_alloc callback function.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The Copyright String in all mpt3sas files are changed to 2012-2013.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The variable 'chain_flags' and 'phy_number' are initialized but never used
otherwise, So remove those unused variables.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
linux/version.h is not necessary as detected by checkversion.pl script.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: "Sreekanth Reddy" <Sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These driver files are initially, substantially similar to mpt2sas but,
because mpt2sas is going into maintenance mode and mp3sas will become heavily
developed, we elected to keep the code bases separate.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Reviewed-by: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
