summaryrefslogtreecommitdiffstats
path: root/drivers/pwm/pwm-mxs.c
AgeCommit message (Collapse)AuthorFilesLines
2021-09-02pwm: mxs: Simplify using devm_pwmchip_add()Uwe Kleine-König1-11/+1
This allows to drop the platform_driver's remove function. This is the only user of driver data so this can go away, too. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2021-09-02pwm: mxs: Don't modify HW state in .probe() after the PWM chip was registeredUwe Kleine-König1-8/+5
This fixes a race condition: After pwmchip_add() is called there might already be a consumer and then modifying the hardware behind the consumer's back is bad. So reset before calling pwmchip_add(). Note that reseting the hardware isn't the right thing to do if the PWM is already running as it might e.g. disable (or even enable) a backlight that is supposed to be on (or off). Fixes: 4dce82c1e840 ("pwm: add pwm-mxs support") Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2021-05-25pwm: Simplify all drivers with explicit of_pwm_n_cells = 3Uwe Kleine-König1-2/+0
With the previous commit there is no need for the lowlevel driver any more to specify it it uses two or three cells. So simplify accordingly. The only non-trival change affects the pwm-rockchip driver: It used to only support three cells if the hardware supports polarity. Now the default number depends on the device tree which has to match hardware anyhow (and if it doesn't the error is just a bit delayed as a PWM handle with an inverted setting is catched when pwm_apply_state() is called). Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2021-03-22pwm: Always allocate PWM chip base ID dynamicallyUwe Kleine-König1-1/+0
Since commit 5e5da1e9fbee ("pwm: ab8500: Explicitly allocate pwm chip base dynamically") all drivers use dynamic ID allocation explicitly. New drivers are supposed to do the same, so remove support for driver specified base IDs and drop all assignments in the low-level drivers. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-03-30pwm: mxs: Remove unused include of of_address.hAnson Huang1-1/+0
There is nothing in use from of_address.h, remove it. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-01-08pwm: mxs: Avoid a division in mxs_pwm_apply()Rasmus Villemoes1-3/+3
Since the divisor is not a compile-time constant (unless gcc somehow decided to unroll the loop PERIOD_CDIV_MAX times), this does a somewhat expensive 32/32 division. Replace that with a right shift. We still have a 64/32 division just below, but at least in that case the divisor is compile-time constant. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-01-08pwm: mxs: Add support for inverse polarityRasmus Villemoes1-4/+10
If I'm reading of_pwm_xlate_with_flags() right, existing device trees that set #pwm-cells = 2 will continue to work. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-01-08pwm: mxs: Remove legacy methodsRasmus Villemoes1-77/+0
Since we now have ->apply(), these are no longer relevant. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2020-01-08pwm: mxs: Implement ->apply()Rasmus Villemoes1-0/+70
In preparation for supporting setting the polarity, switch the driver to support the ->apply() method. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2019-09-21pwm: mxs: Use devm_platform_ioremap_resource() to simplify codeAnson Huang1-3/+1
Use the new helper devm_platform_ioremap_resource() which wraps the platform_get_resource() and devm_ioremap_resource() together, to simplify the code. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2018-07-12pwm: mxs: Switch to SPDX identifierFabio Estevam1-7/+1
Adopt the SPDX license identifier headers to ease license compliance management. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2017-01-04pwm: Remove .can_sleep from struct pwm_chipThierry Reding1-1/+1
All PWM devices have been marked as "might sleep" since v4.5, there is no longer a need to differentiate on a per-chip basis. Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2015-07-20pwm: Add the pwm_is_enabled() helperBoris Brezillon1-2/+2
Some PWM drivers are testing the PWMF_ENABLED flag. Create a helper function to hide the logic behind enabled test. This will allow us to smoothly move from the current approach to an atomic PWM update approach. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2015-03-11pwm: mxs: Fix period divider computationGaetan Hug1-2/+6
The driver computes which clock divider it sould be using from the requested period. This computation assumes that the link between the register value and the actual divider value is raising 2 to the power of the registry value. div = 1 << regvalue This is true only for the first 5 values out of 8. Next values are 64, 256 and, 1024 - instead of 32, 64, 128. This affects only the users requesting a period > 0.04369s. Replace the computation with a look-up table. Signed-off-by: Gaetan Hug <ghug@induct.be> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2014-10-20pwm: drop owner assignment from platform_driversWolfram Sang1-1/+0
A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-05-21pwm: mxs: set pwm_chip can_sleep flagShawn Guo1-0/+1
The .config() calls clk_get_rate() which might sleep, so we need to set pwm_chip can_sleep flag. Otherwise, we see the following warning when using PWM driven heartbeat led. WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:856 mutex_trylock+0x184/0x1a4() DEBUG_LOCKS_WARN_ON(in_interrupt()) Modules linked in: CPU: 0 PID: 0 Comm: swapper Not tainted 3.14.0-rc5 #18 [<c0015420>] (unwind_backtrace) from [<c0012cb0>] (show_stack+0x10/0x14) [<c0012cb0>] (show_stack) from [<c001daf8>] (warn_slowpath_common+0x6c/0x8c) [<c001daf8>] (warn_slowpath_common) from [<c001dbac>] (warn_slowpath_fmt+0x30/0x40) [<c001dbac>] (warn_slowpath_fmt) from [<c045df74>] (mutex_trylock+0x184/0x1a4) [<c045df74>] (mutex_trylock) from [<c0360950>] (clk_prepare_lock+0xc/0xec) [<c0360950>] (clk_prepare_lock) from [<c0362020>] (clk_get_rate+0xc/0x68) [<c0362020>] (clk_get_rate) from [<c028d07c>] (mxs_pwm_config+0x20/0x198) [<c028d07c>] (mxs_pwm_config) from [<c028bde8>] (pwm_config+0x60/0x70) [<c028bde8>] (pwm_config) from [<c034b61c>] (__led_pwm_set+0x1c/0x3c) [<c034b61c>] (__led_pwm_set) from [<c034bc3c>] (led_heartbeat_function+0x70/0x110) [<c034bc3c>] (led_heartbeat_function) from [<c00292f0>] (call_timer_fn+0x7c/0x164) [<c00292f0>] (call_timer_fn) from [<c00295c8>] (run_timer_softirq+0x1f0/0x260) [<c00295c8>] (run_timer_softirq) from [<c002255c>] (__do_softirq+0xc4/0x2f0) [<c002255c>] (__do_softirq) from [<c0022890>] (irq_exit+0xa4/0x10c) [<c0022890>] (irq_exit) from [<c0010240>] (handle_IRQ+0x34/0x84) [<c0010240>] (handle_IRQ) from [<c0013524>] (__irq_svc+0x44/0x54) [<c0013524>] (__irq_svc) from [<c00107f8>] (arch_cpu_idle+0x40/0x48) [<c00107f8>] (arch_cpu_idle) from [<c005deb8>] (cpu_startup_entry+0x70/0x198) [<c005deb8>] (cpu_startup_entry) from [<c060aac8>] (start_kernel+0x2a8/0x2f8) Reported-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-10-08pwm: mxs: Remove redundant of_match_ptrSachin Kamat1-1/+1
The data structure of_match_ptr() protects is always compiled in. Hence of_match_ptr() is not needed. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-09-03pwm: mxs: Check the return value from stmp_reset_block()Fabio Estevam1-1/+7
stmp_reset_block() may fail, so let's check its return value and propagate it in the case of error. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-06-12pwm: Fill in missing .owner fieldsThierry Reding1-0/+1
Some drivers don't set the .owner fields of the struct device_driver or struct pwm_ops, which causes the module usage count to become wrong. Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-05-27pwm: mxs: Let device core handle pinctrlFabio Estevam1-6/+0
Since commit ab78029 (drivers/pinctrl: grab default handles from device core), we can rely on device core for handling pinctrl. So remove devm_pinctrl_get_select_default() from the driver. Cc: Thierry Reding <thierry.reding@avionic-design.de> Cc: <linux-kernel@vger.kernel.org> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-04-23pwm: Constify OF match tablesThierry Reding1-1/+1
A few drivers already annotate this properly. Make the same change for all other OF supporting drivers. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
2013-04-02pwm: mxs: Remove unused *dev from struct mxs_pwm_chipAxel Lin1-2/+0
Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2013-01-22pwm: Convert to devm_ioremap_resource()Thierry Reding1-3/+3
Convert all uses of devm_request_and_ioremap() to the newly introduced devm_ioremap_resource() which provides more consistent error handling. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-28pwm: remove use of __devexitBill Pemberton1-1/+1
CONFIG_HOTPLUG is going away as an option so __devexit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Acked-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-28pwm: remove use of __devexit_pBill Pemberton1-1/+1
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Acked-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-07-23pwm: pwm-mxs: Return proper error if pwmchip_remove() failsAxel Lin1-3/+1
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23pwm: pwm-mxs: add pinctrl supportShawn Guo1-0/+6
Call pinctrl subsystem to set up pwm pin. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23pwm: pwm-mxs: use devm_* managed functionsShawn Guo1-16/+8
Use devm_* managed functions to have a clean fail-out. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23pwm: pwm-mxs: use global reset function stmp_reset_blockShawn Guo1-2/+2
Use global reset function stmp_reset_block instead of mxs_reset_block to remove <mach/common.h> inclusion. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23pwm: pwm-mxs: encode soc name in compatible stringShawn Guo1-1/+1
Encode soc name in the compatible string to know the specific version hardware block. This is the general approach adopted for most bindings. Change mxs-pwm binding to use the approach. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-02pwm: add pwm-mxs supportShawn Guo1-0/+207
Add generic PWM framework driver (DT only) for Freescale MXS. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-30 14:04:30 +0000