| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-next 2021-04-09
This pr contains changes from mlx5-next branch,
already reviewed on netdev and rdma mailing lists, links below.
1) From Leon, Dynamically assign MSI-X vectors count
Already Acked by Bjorn Helgaas.
https://patchwork.kernel.org/project/netdevbpf/cover/20210314124256.70253-1-leon@kernel.org/
2) Cleanup series:
https://patchwork.kernel.org/project/netdevbpf/cover/20210311070915.321814-1-saeed@kernel.org/
From Mark, E-Switch cleanups and refactoring, and the addition
of single FDB mode needed HW bits.
From Mikhael, Remove unused struct field
From Saeed, Cleanup W=1 prototype warning
From Zheng, Esw related cleanup
From Tariq, User order-0 page allocation for EQs
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Implement sriov_get_vf_total_msix/count() callbacks
net/mlx5: Dynamically assign MSI-X vectors count
net/mlx5: Add dynamic MSI-X capabilities bits
PCI/IOV: Add sysfs MSI-X vector assignment interface
net/mlx5: Use order-0 allocations for EQs
net/mlx5: Add IFC bits needed for single FDB mode
net/mlx5: E-Switch, Refactor send to vport to be more generic
RDMA/mlx5: Use representor E-Switch when getting netdev and metadata
net/mlx5: E-Switch, Add eswitch pointer to each representor
net/mlx5: E-Switch, Add match on vhca id to default send rules
net/mlx5: Remove unused mlx5_core_health member recover_work
net/mlx5: simplify the return expression of mlx5_esw_offloads_pair()
net/mlx5: Cleanup prototype warning
====================
Link: https://lore.kernel.org/r/20210409200704.10886-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The following diagram illustrates the hardware model for tc sample action:
+---------------------+
+ original flow table +
+---------------------+
+ original match +
+---------------------+
|
v
+------------------------------------------------+
+ Flow Sampler Object +
+------------------------------------------------+
+ sample ratio +
+------------------------------------------------+
+ sample table id | default table id +
+------------------------------------------------+
| |
v v
+-----------------------------+ +----------------------------------------+
+ sample table + + default table per <vport, chain, prio> +
+-----------------------------+ +----------------------------------------+
+ forward to management vport + + original match +
+-----------------------------+ +----------------------------------------+
+ other actions +
+----------------------------------------+
The sample action is translated to a goto flow table object
destination which samples packets according to the provided
sample ratio. Sampled packets are duplicated. One copy is
processed by a termination table, named the sample table,
which sends the packet to the eswitch manager port (that will
be processed by software).
The second copy is processed by the default table which executes
the subsequent actions. The default table is created per <vport,
chain, prio> tuple as rules with different prios and chains may
overlap.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, the u32 chain id is mapped to u16 value which is stored on
the lower 16 bits of reg_c0 for FDB and reg_b for NIC tables. The
mapping is internally maintained by the chains object. However, with
the introduction of reg_c0 objects the fdb may store more than just
the chain id on reg_c0. This is not relevant for NIC tables.
Separate the chains mapping instantiation for FDB and NIC tables.
Remove the mapping from the chains object. For FDB tables, create
the mapping per eswitch. For NIC tables, create the mapping per tc
table. Pass the corresponding mapping pointer when creating the
chains object.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently reg_c0 lower 16 bits and reg_b are used to store the chain
id that missed in FDB and NIC tables accordingly. However, the
registers' values may index a restore object, rather than a single u32
value. Different object types can be used to restore mutually exclusive
contexts such as chain id and sample group id.
Use the mapping object to associate an index with a restore object
as a prestep for supporting additional restore types.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, per vport table was used only for port mirroring actions.
However, sample action will also require a per vport table instance.
Generalize the vport table API to work with multiple namespaces where
each namespace manages its own vport table instance.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Public api starts with mlx5 and remove mlx5 for non-public api.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, the vport table functions are in common eswitch offload
file. This file is too big. Move the vport table create, delete and
lookup functions to a separate file. Put the file in esw directory.
Pre-step for generalizing its functionality for serving both the
mirroring and the sample features.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Create send to vport miss group was added in order to support traffic
recirculation to root table with metadata source rewrite.
This group is created also in case source rewrite isn't supported.
Fixed by creating send to vport miss group only if source rewrite is
supported by FW.
Fixes: 8e404fefa58b ("net/mlx5e: Match recirculated packet miss in slow table using reg_c1")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
indir_table.h has been included at line 41, so remove
the duplicate one at line 43.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We re-use the native NIC port net device instance for the Uplink
representor, a driver currently cannot unbind TC setup callback
actively, hence protect changing E-Switch mode while adding rules.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
E-Switch mode change routine will take the write lock to prevent any
consumer to access the E-Switch resources while E-Switch is going
through a mode change.
In the next patch
E-Switch consumers (e.g vport representors) will take read_lock prior to
accessing E-Switch resources to prevent E-Switch mode changing in the
middle of the operation.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
We will re-use the native NIC port net device instance for the Uplink
representor. As such we also don't want to unregister/register the
devlink port as part of the profile.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Now that each representor stores a pointer to the managing E-Switch
use that information when creating the send-to-vport rules.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Store the managing E-Switch of each representor. This will be used
when a representor is created on eswitch manager 0 but the vport
belongs to eswitch manager 1.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Match on the vhca id of the E-Switch owner when creating the send-to-vport
representor rules.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
flow spec is not small and we do allocate it using kvzalloc
in most places of the driver. fix rest of the places
to use kvzalloc to avoid failure in allocation when
memory is too fragmented.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Users of mlx5_eswitch_get_vport() are required to check return value
prior to passing mlx5_vport further. Fix all the places to do not skip
that check.
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
VF tunnel TX traffic offload is adding flow which forward to flow
tables with lower level, which isn't support on all FW versions
and may cause firmware to fail with syndrome.
Fixed by enabling VF tunnel TX offload only if flow table capability
ignore_flow_level is enabled.
Fixes: 10742efc20a4 ("net/mlx5e: VF tunnel TX traffic offloading")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Previous patch in series that implements stack devices RX path implements
indirect table rules that match on tunnel VNI. After such rule is created
all tunnel traffic is recirculated to root table. However, recirculated
packet might not match on any rules installed in the table (for example,
when IP traffic follows ARP traffic). In that case packets appear on
representor of tunnel endpoint VF instead being redirected to the VF
itself.
Extend slow table with additional flow group that matches on reg_c0 (source
port value set by indirect tables implemented by previous patch in series)
and reg_c1 (special 0xFFF mark). When creating offloads fdb tables, install
one rule per VF vport to match on recirculated miss packets and redirect
them to appropriate VF vport. Modify indirect tables code to also rewrite
reg_c1 with special 0xFFF mark.
Implementation reuses reg_c1 tunnel id bits. This is safe to do because
recirculated packets are always matched before decapsulation.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When tunnel endpoint is on VF the encapsulated RX traffic is exposed on the
representor of the VF without any further processing of rules installed on
the VF. Detect such case by checking if the device returned by route lookup
in decap rule handling code is a mlx5 VF and handle it with new redirection
tables API.
Example TC rules for VF tunnel traffic:
1. Rule that encapsulates the tunneled flow and redirects packets from
source VF rep to tunnel device:
$ tc -s filter show dev enp8s0f0_1 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac 0a:40:bd:30:89:99
src_mac ca:2e:a7:3f:f5:0f
eth_type ipv4
ip_tos 0/0x3
ip_flags nofrag
in_hw in_hw_count 1
action order 1: tunnel_key set
src_ip 7.7.7.5
dst_ip 7.7.7.1
key_id 98
dst_port 4789
nocsum
ttl 64 pipe
index 1 ref 1 bind 1 installed 411 sec used 411 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
no_percpu
used_hw_stats delayed
action order 2: mirred (Egress Redirect to device vxlan_sys_4789) stolen
index 1 ref 1 bind 1 installed 411 sec used 0 sec
Action statistics:
Sent 5615833 bytes 4028 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 5615833 bytes 4028 pkt
backlog 0b 0p requeues 0
cookie bb406d45d343bf7ade9690ae80c7cba4
no_percpu
used_hw_stats delayed
2. Rule that redirects from tunnel device to UL rep:
$ tc -s filter show dev vxlan_sys_4789 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac ca:2e:a7:3f:f5:0f
src_mac 0a:40:bd:30:89:99
eth_type ipv4
enc_dst_ip 7.7.7.5
enc_src_ip 7.7.7.1
enc_key_id 98
enc_dst_port 4789
enc_tos 0
ip_flags nofrag
in_hw in_hw_count 1
action order 1: tunnel_key unset pipe
index 2 ref 1 bind 1 installed 434 sec used 434 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
action order 2: mirred (Egress Redirect to device enp8s0f0_1) stolen
index 4 ref 1 bind 1 installed 434 sec used 0 sec
Action statistics:
Sent 129936 bytes 1082 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 129936 bytes 1082 pkt
backlog 0b 0p requeues 0
cookie ac17cf398c4c69e4a5b2f7aabd1b88ff
no_percpu
used_hw_stats delayed
Co-developed-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Indirect table infrastructure is used to allow fully processing VF tunnel
traffic in hardware. Kernel software model uses two TC rules for such
traffic: UL rep to tunnel device, then tunnel VF rep to destination VF rep.
To implement such pipeline driver needs to program the hardware after
matching on UL rule to overwrite source vport from UL to tunnel VF and
recirculate the packet to the root table to allow matching on the rule
installed on tunnel VF. For this indirect table matches all encapsulated
traffic by tunnel parameters and all other IP traffic is sent to tunnel VF
by the miss rule.
Indirect table API overview:
- mlx5_esw_indir_table_{init|destroy}() - init and destroy opaque indirect
table object.
- mlx5_esw_indir_table_get() - get or create new table according to vport
id and IP version. Table has following pre-created groups: recirculation
group with match on ethertype and VNI (rules that match encapsulated
packets are installed to this group) and forward group with default/miss
rule that forwards to vport of tunnel endpoint VF (rule for regular
non-encapsulated packets).
- mlx5_esw_indir_table_put() - decrease reference to the indirect table and
matching rule (for encapsulated traffic).
- mlx5_esw_indir_table_needed() - check that in_port is an uplink port and
out_port is VF on the same eswitch, verify that the rule is for IP traffic
and source port rewrite functionality can be used.
- mlx5_esw_indir_table_decap_vport() - function returns decap vport of
flow attribute.
Co-developed-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When tunnel endpoint is on VF, driver still assumes that endpoint is on
uplink and incorrectly configures encap rule offload according to that
assumption. As a result, traffic is sent directly to the uplink and rules
installed on representor of tunnel endpoint VF are ignored.
Implement following changes to allow offloading tx traffic with tunnel
endpoint on VF:
- For tunneling flows perform route lookup on route and out devices pair.
If out device is uplink and route device is VF of same physical port, then
modify packet reg_c_0 metadata register (source port) with the value of VF
vport. Use eswitch vhca_id->vport mapping introduced in one of previous
patches in the series to obtain vport from route netdevice.
- Recirculate encapsulated packets to VF vport in order to apply any flow
rules installed on VF representor that match on encapsulated traffic.
Only enable support for this functionality when all following conditions
are true:
- Hardware advertises capability to preserve reg_c_0 value on packet
recirculation.
- Vport metadata matching is enabled.
- Termination tables are to be used by the flow.
Example TC rules for VF tunnel traffic:
1. Rule that redirects packets from UL to VF rep that has the tunnel
endpoint IP address:
$ tc -s filter show dev enp8s0f0 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac 16:c9:a0:2d:69:2c
src_mac 0c:42:a1:58:ab:e4
eth_type ipv4
ip_flags nofrag
in_hw in_hw_count 1
action order 1: mirred (Egress Redirect to device enp8s0f0_0) stolen
index 3 ref 1 bind 1 installed 377 sec used 0 sec
Action statistics:
Sent 114096 bytes 952 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 114096 bytes 952 pkt
backlog 0b 0p requeues 0
cookie 878fa48d8c423fc08c3b6ca599b50a97
no_percpu
used_hw_stats delayed
2. Rule that decapsulates the tunneled flow and redirects to destination VF
representor:
$ tc -s filter show dev vxlan_sys_4789 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac ca:2e:a7:3f:f5:0f
src_mac 0a:40:bd:30:89:99
eth_type ipv4
enc_dst_ip 7.7.7.5
enc_src_ip 7.7.7.1
enc_key_id 98
enc_dst_port 4789
enc_tos 0
ip_flags nofrag
in_hw in_hw_count 1
action order 1: tunnel_key unset pipe
index 2 ref 1 bind 1 installed 434 sec used 434 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
action order 2: mirred (Egress Redirect to device enp8s0f0_1) stolen
index 4 ref 1 bind 1 installed 434 sec used 0 sec
Action statistics:
Sent 129936 bytes 1082 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 129936 bytes 1082 pkt
backlog 0b 0p requeues 0
cookie ac17cf398c4c69e4a5b2f7aabd1b88ff
no_percpu
used_hw_stats delayed
Co-developed-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Following patches in the series extend forwarding functionality with VF
tunnel TX and RX handling. Extract action forwarding processing code into
dedicated functions to simplify further extensions:
- Handle every forwarding case with dedicated function instead of inline
code.
- Extract forwarding dest dispatch conditional into helper function
esw_setup_dests().
- Unify forwaring cleanup code in error path of
mlx5_eswitch_add_offloaded_rule() and in rule deletion code of
__mlx5_eswitch_del_rule() in new helper function esw_cleanup_dests() (dual
to new esw_setup_dests() helper).
This patch does not change functionality.
Co-developed-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Following patches in the series need to be able to map VF netdev to vport.
Since it is trivial to obtain vhca_id from netdev, maintain mapping from
vhca_id to vport_num inside eswitch offloads using xarray. Provide function
mlx5_eswitch_vhca_id_to_vport() to be used by TC code in following patches
to obtain the mapping.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Setting the source port requires only the E-Switch and vport number.
Refactor the function to get those parameters instead of passing the full
attribute.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add helpers to enable/disable eswitch port, register its devlink port and
load its representor.
Signed-off-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Prepare eswitch to handle SF vport during
(a) querying eswitch functions
(b) egress ACL creation
(c) account for SF vports in total vports calculation
Assign a dedicated placeholder for SFs vports and their representors.
They are placed after VFs vports and before ECPF vports as below:
[PF,VF0,...,VFn,SF0,...SFm,ECPF,UPLINK].
Change functions to map SF's vport numbers to indices when
accessing the vports or representors arrays, and vice versa.
Signed-off-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since kvzalloc will initialize the allocated memory, it is not
necessary to initialize it once again.
Fixes: 11b717d61526 ("net/mlx5: E-Switch, Get reg_c0 value on CQE")
Signed-off-by: Zhu Yanjun <yanjunz@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Set flow source as hint for local vport.
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently devlink eswitch ports are registered and unregistered by the
representor layer.
However it is better to register them at eswitch layer so that in future
user initiated command port add and delete commands can also
register/unregister devlink ports without depending on representor layer.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
To register and unregister devlink ports when loading/unload
representors, refactor the code to helper functions.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently only VF vports need egress ACL table.
Add a generic helper to check whether a vport need egress
ACL table or not.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently only 256 vports can be supported as only 8 bits are
reserved for them and 8 bits are reserved for vhca_ids in
metadata reg c0. To support more than 256 vports, replace
vhca_id with a unique shorter 4-bit PF number which covers
upto 16 PF's. Use remaining 12 bits for vports ranging 1-4095.
This will continue to generate unique metadata even if
multiple PCI devices have same switch_id.
Signed-off-by: sunils <sunils@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In order to support chains and connection tracking offload for
nic flows, there's a need to introduce a common flow attributes
struct so that these features can be agnostic and have access to
a single attributes struct, regardless of the flow type.
Therefore, a new tc flow attributes format is introduced to allow
access to attributes that are common to eswitch and nic flows.
The common attributes will always get allocated for the new flows,
regardless of their type, while the type specific attributes are
separated into different structs and will be allocated based on the
flow type to avoid memory waste.
When allocating the flow attributes the caller provides the flow
steering namespace and according the namespace type the additional
space for the extra, type specific, attributes is determined and
added to the total attribute allocation size.
In addition, the attributes that are going to be common to both
flow types are moved to the common attributes struct.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Decouple the chains infrastructure from eswitch and make
it generic to support other steering namespaces.
The change defines an agnostic data structure to keep
all the relevant information for maintaining flow table
chaining in any steering namespace. Each namespace that
requires table chaining will be required to allocate
such data structure.
The chains creation code will receive the steering namespace
and flow table parameters from the caller so it will operate
agnosticly when creating the required resources to
maintain the table chaining function while Parts of the code
that are relevant to eswitch specific functionality are moved
to eswitch files.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cited commit creates peer miss group during switchdev mode
initialization in order to handle miss packets correctly while in VF
LAG mode. This is done regardless of FW support of such groups which
could cause rules setups failure later on.
Fix by adding FW capability check before creating peer groups/rule.
Fixes: ac004b832128 ("net/mlx5e: E-Switch, Add peer miss rules")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Multiple features use metadata matching such as bond vport
in live migration, multi-port RoCE mode, stacked devices;
hence, enable vport metadata matching by default.
Fixes: 1e62e222db2e ("net/mlx5: E-Switch, Use vport metadata matching only when mandatory")
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In merged eswitch configuration, peer miss rule is setup for all
vports. If metadata is enabled, peer miss rule with metadata matching
will be configured instead of source port matching; however, some
vports that have not yet been enabled don't have default_metadata
setup and their default_metadata will be zero.
Hence, setup/cleanup default metadata for all vports when eswitch moves
in/out of offloads mode.
Fixes: 133dcfc577ea ("net/mlx5: E-Switch, Alloc and free unique metadata for match")
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Uplink vport must have a dedicated metadata with vhca_id
being part of the metadata.
Fixes: 133dcfc577ea ("net/mlx5: E-Switch, Alloc and free unique metadata for match")
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Check E-Switch capabilities and enable metadata support flag
before using it to setup other features that need metadata.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
ECPF supports one external host controller. Read controller number
from the device.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resolved kernel/bpf/btf.c using instructions from merge commit
69138b34a7248d2396ab85c8652e20c0c39beaba
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flow_source must be specified, even for rule without matching
source vport, because some actions are only allowed in uplink.
Otherwise, rule can't be offloaded and firmware syndrome happens.
Fixes: 6fb0701a9cfa ("net/mlx5: E-Switch, Add support for offloading rules with no in_port")
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The modified flow_context fields in FTE must be indicated in
modify_enable bitmask. Previously, the misc bit in modify_enable is
always set as source vport must be set for each rule. So, when parsing
vxlan/gre/geneve/qinq rules, this bit is not set because those are all
from the same misc fileds that source vport fields are located at, and
we don't need to set the indicator twice.
After adding per vport tables for mirroring, misc bit is not set, then
firmware syndrome happens. To fix it, set the bit wherever misc fileds
are changed. This also makes it unnecessary to check misc fields and set
the misc bit accordingly in metadata matching, so here remove it.
Besides, flow_source must be specified for uplink because firmware
will check it and some actions are only allowed for packets received
from uplink.
Fixes: 96e326878fa5 ("net/mlx5e: Eswitch, Use per vport tables for mirroring")
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently steering table and rx group initialization helper
routines works on the total_vports passed as input parameter.
Both eswitch helpers work on the mlx5_eswitch and thereby have access
to esw->total_vports. Hence use it directly instead of passing it
via function input arguments.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
