| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.13-rc1.
Actually busy this release, with a number of cleanups happening:
- much needed core tty cleanups by Jiri Slaby
- removal of unused and orphaned old-style serial drivers. If anyone
shows up with this hardware, it is trivial to restore these but we
really do not think they are in use anymore.
- fixes and cleanups from Johan Hovold on a number of termios setting
corner cases that loads of drivers got wrong as well as removing
unneeded code due to tty core changes from long ago that were never
propagated out to the drivers
- loads of platform-specific serial port driver updates and fixes
- coding style cleanups and other small fixes and updates all over
the tty/serial tree.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
serial: extend compile-test coverage
serial: stm32: add FIFO threshold configuration
dt-bindings: serial: 8250: update TX FIFO trigger level
dt-bindings: serial: stm32: override FIFO threshold properties
dt-bindings: serial: add RX and TX FIFO properties
serial: xilinx_uartps: drop low-latency workaround
serial: vt8500: drop low-latency workaround
serial: timbuart: drop low-latency workaround
serial: sunsu: drop low-latency workaround
serial: sifive: drop low-latency workaround
serial: txx9: drop low-latency workaround
serial: sa1100: drop low-latency workaround
serial: rp2: drop low-latency workaround
serial: rda: drop low-latency workaround
serial: owl: drop low-latency workaround
serial: msm_serial: drop low-latency workaround
serial: mpc52xx_uart: drop low-latency workaround
serial: meson: drop low-latency workaround
serial: mcf: drop low-latency workaround
serial: lpc32xx_hs: drop low-latency workaround
...
|
|
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/usb/core/hub.c: usb_new_device() contains the following:
/* By default, forbid autosuspend for all devices. It will be
* allowed for hubs during binding.
*/
usb_disable_autosuspend(udev);
So for anything which is not a hub, such as btusb devices, autosuspend is
disabled by default and we must call usb_enable_autosuspend(udev) to
enable it.
This means that the "Fix the autosuspend enable and disable" commit,
which drops the usb_enable_autosuspend() call when the enable_autosuspend
module option is true, is completely wrong, revert it.
This reverts commit 7bd9fb058d77213130e4b3e594115c028b708e7e.
Cc: Hui Wang <hui.wang@canonical.com>
Fixes: 7bd9fb058d77 ("Bluetooth: btusb: Fix the autosuspend enable and disable")
Acked-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Proper support for BCM4330 and BMC4334
- Various improvements for firmware download of Intel controllers
- Update management interface revision to 20
- Support for AOSP HCI vendor commands
- Initial Virtio support
====================
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for Bluetooth HCI transport over virtio.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
We need the serial/tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adding support LE scatternet and WBS for Mediatek Chip
Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This skips parsing the firmware version information from the firmware
file while controller is in bootloader mode. As in bootloader mode,
we are supposed to patch unconditionally.
Signed-off-by: Lokendra Singh <lokendra.singh@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In Operational firmware mode, 'Minimum FW version' TLV ID is not available.
So, we cannot fetch already running firmware info for comparison against
another build. However, It can be collected using a combination of other
TLV ID's information.
Signed-off-by: Lokendra Singh <lokendra.singh@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
intel_version_tlv parsing
This moves limited_cce and sbe_type checks under bootloader during tlv parsing
as operational firmware don't have access to these values. Any attempt to read
such values in operational firmware will only fetch garbage data.
Signed-off-by: Lokendra Singh <lokendra.singh@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This moves duplicated code for waiting firmware download completion to
a function that can be reused.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This moves duplicated code for waiting firmware download completion to
a function that can be reused.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This moves version checks of intel_version() to btintel_version_info().
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This moves version checks of intel_version_tlv() to btintel_version_info_tlv().
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In order to allow new firmware to load, it first needs to check if the
firmware version on file matches the one loaded if it doesn't, then it
needs to revert to bootloader mode in order to load the new firmware.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This checks the firmware build number, week and year against the
repective loaded version. If details are a match, skip the download
process.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
s/packat/packet/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add the missing brcm,bcm4330-bt and brcm,bcm4334-bt to the
match table so device trees can use this compatible as well
and not need to use the fallback brcm,bcm4329-bt.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Based on device may wakeup status, Bluez stack will enable/disable
passive scanning with whitelist in BT controller while suspending.
As interrupt from BT SoC is handled by UART driver,we need to use
device handle of UART driver to get the status of device may wakeup
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
First, it is never checked. Second, use of it as a debugging aid is
at least questionable. With the current tools, I don't think anyone used
this kind of thing for debugging purposes for years.
On the top of that, e.g. serdev does not set this field of tty_ldisc_ops
at all.
So get rid of this legacy.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Boot address parameter was not getting updated properly
due to wrong offset
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
print the firmware file name on error loading from fie system
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Obtain and drive the optional reset GPIO line if this is
not hardwired in the platform. This is needed on the
Samsung GT-I9070 mobile phone.
The invers of power is used, this should be OK to apply
simultaneously as the power signal according to
figures 47-51 on pages 159-161 in the BCM4330 datasheet.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Warnings: drivers/bluetooth/btusb.c:3775 btusb_mtk_setup() error:
uninitialized symbol 'fw_version'.
-> add initial value for fw_version.
Warnings: sparse: sparse: incorrect type in assignment (different base
types)
-> add le32_to_cpu to fix incorrect type in assignment.
Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Some Xiaomi RedmiBook laptop models use the 0cb5:c547 USB identifier
for their Bluetooth device, so load the appropriate firmware for
Realtek 8822CE.
-Device(0cb5:c547) from /sys/kernel/debug/usb/devices
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cb5 ProdID=c547 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Rasmus Moorats <xx@nns.ee>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver changes for 5.12-rc1.
Nothing huge, just lots of good cleanups and additions:
- n_tty line discipline cleanups
- vt core cleanups and reworks to make the code more "modern"
- stm32 driver additions
- tty led support added to the tty core and led layer
- minor serial driver fixups and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (54 commits)
serial: core: Remove BUG_ON(in_interrupt()) check
vt_ioctl: Remove in_interrupt() check
dt-bindings: serial: imx: Switch to my personal address
vt: keyboard, use new API for keyboard_tasklet
serial: stm32: improve platform_get_irq condition handling in init_port
serial: ifx6x60: Remove driver for deprecated platform
tty: fix up iterate_tty_read() EOVERFLOW handling
tty: fix up hung_up_tty_read() conversion
tty: fix up hung_up_tty_write() conversion
tty: teach the n_tty ICANON case about the new "cookie continuations" too
tty: teach n_tty line discipline about the new "cookie continuations"
tty: clean up legacy leftovers from n_tty line discipline
tty: implement read_iter
tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer
serial: remove sirf prima/atlas driver
serial: mxs-auart: Remove <asm/cacheflush.h>
serial: mxs-auart: Remove serial_mxs_probe_dt()
serial: fsl_lpuart: Use of_device_get_match_data()
dt-bindings: serial: renesas,hscif: Add r8a779a0 support
tty: serial: Drop unused efm32 serial driver
...
|
|
If BT SoC is running with ROM FW then just return in
qca_suspend function as ROM FW does not support
in-band sleep.
Fixes: 2be43abac5a8 ("Bluetooth: hci_qca: Wait for timeout during suspend")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This issue starts from linux-5.10-rc1, I reproduced this issue on my
Dell Inspiron 7447 with BT adapter 0cf3:e005, the kernel will print
out: "Bluetooth: hci0: don't support firmware rome 0x31010000", and
someone else also reported the similar issue to bugzilla #211571.
I found this is a regression introduced by 'commit b40f58b97386
("Bluetooth: btusb: Add Qualcomm Bluetooth SoC WCN6855 support"), the
patch assumed that if high ROM version is not zero, it is an adapter
on WCN6855, but many old adapters don't need to load rampatch or nvm,
and they have non-zero high ROM version.
To fix it, let the driver match the rom_version in the
qca_devices_table first, if there is no entry matched, check the
high ROM version, if it is not zero, we assume this adapter is ready
to work and no need to load rampatch and nvm like previously.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211571
Fixes: b40f58b97386 ("Bluetooth: btusb: Add Qualcomm Bluetooth SoC WCN6855 support")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Enlarging the size of 'struct btmtk_hci_wmt_cmd' makes it no longer
fit on the kernel stack, as seen from this compiler warning:
drivers/bluetooth/btusb.c:3365:12: error: stack frame size of 1036 bytes in function 'btusb_mtk_hci_wmt_sync' [-Werror,-Wframe-larger-than=]
Change the function to dynamically allocate the buffer instead.
As there are other sleeping functions called from the same location,
using GFP_KERNEL should be fine here, and the runtime overhead should
not matter as this is rarely called.
Unfortunately, I could not figure out why the message size is
increased in the previous patch. Using dynamic allocation means
any size is possible now, but there is still a range check that
limits the total size (including the five-byte header) to 255
bytes, so whatever was intended there is now undone.
Fixes: 48c13301e6ba ("Bluetooth: btusb: Fine-tune mt7663 mechanism.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
btusb_mtk_setup_firmware_79xx
Fix follow warning:
drivers/bluetooth/btusb.c:3479:9: warning: variable ‘fw_size’ set but not used [-Wunused-but-set-variable]
size_t fw_size;
^~~~~~~
drivers/bluetooth/btusb.c:3473:29: warning: variable ‘patchhdr’ set but not used [-Wunused-but-set-variable]
struct btmtk_patch_header *patchhdr = NULL;
^~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Change "deivice" to "device"
Correct "Unsupported support hardware variant (%08x)" to
"Unsupported hardware variant (%08x)"
Signed-off-by: Jupeng Zhong <zhongjupeng@yulong.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
I tried to disable the autosuspend on btusb through the module
parameter enable_autosuspend, this parameter is set to N, but the usb
bluetooth device is still runtime suspended.
$ cat /sys/module/btusb/parameters/enable_autosuspend
N
$ cat /sys/bus/usb/devices/3-10/power/runtime_status
suspended
$ cat /sys/bus/usb/devices/3-10/power/runtime_suspended_time
65187
We already set ".supports_autosuspend = 1" in the usb_driver, this
device will be set autosuspend enabled by usb core, we don't need
to call usb_enable_autosuspend() in the btusb_probe(). Instead if
users set the parameter enable_autosuspend to N, we need to call
usb_disable_autosuspend() in the btusb_probe(). After this change
and set the parameter to N, we could see the device is not runtime
suspended anymore.
$ cat /sys/module/btusb/parameters/enable_autosuspend
N
$ cat /sys/bus/usb/devices/3-10/power/runtime_status
active
$ cat /sys/bus/usb/devices/3-10/power/runtime_suspended_time
0
And if we disable the autosuspend in the btusb_probe(), we need to
enable the autosuspend in the disconnect(), this could guarantee
that the device could be runtime suspended after we rmmod the btusb.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In btusb_mtk_wmt_recv if skb_clone fails, the alocated skb should be
released.
Omit the labels “err_out” and “err_free_skb” in this function
implementation so that the desired exception handling code
would be directly specified in the affected if branches.
Fixes: a1c49c434e15 ("btusb: Add protocol support for MediaTek MT7668U USB devices")
Signed-off-by: Jupeng Zhong <zhongjupeng@yulong.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
There is mt7921 firmware download mechanism
1. Read Chip id from MT7921.
2. Download firmware by endpoint 0, it's the same mechanism with
mt7663/mt7668.
(it's medaitek specific header format for downloading firmware.)
3. Enabling Bluetooth function.
The information in /sys/kernel/debug/usb/devices about the MT7921U
Bluetooth device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 40 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0e8d ProdID=7961 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fine-tune read register for mt7663/mt7921.
For mediatek chip spcific wmt protocol, we add more delay to send EP0
In-Token.
Signed-off-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
QCA_IBS_DISABLED flag will be set after memorydump started from
controller.Currently qca_suspend() is waiting for SSR to complete
based on flag QCA_IBS_DISABLED.Added to check for QCA_SSR_TRIGGERED
flag too.
Fixes: 2be43abac5a8 ("Bluetooth: hci_qca: Wait for timeout during suspend")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
By this change, it will enable WBS supported on the specific Realtek BT
devices, such as RTL8822C and RTL8852A.
In the future, it's able to maintain what the Realtek devices support WBS
here.
Tested-by: Hilda Wu <hildawu@realtek.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Realtek Bluetooth controllers can do both LE scan and BR/EDR inquiry
at once, need to set HCI_QUIRK_SIMULTANEOUS_DISCOVERY quirk.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into tty-next
Fixes both the "splice/sendfile to a tty" and "splice/sendfile from a
tty" regression from 5.10.
* 'tty-splice' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux:
tty: teach the n_tty ICANON case about the new "cookie continuations" too
tty: teach n_tty line discipline about the new "cookie continuations"
tty: clean up legacy leftovers from n_tty line discipline
tty: implement read_iter
tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer
tty: implement write_iter
|
|
The tty line discipline .read() function was passed the final user
pointer destination as an argument, which doesn't match the 'write()'
function, and makes it very inconvenient to do a splice method for
ttys.
This is a conversion to use a kernel buffer instead.
NOTE! It does this by passing the tty line discipline ->read() function
an additional "cookie" to fill in, and an offset into the cookie data.
The line discipline can fill in the cookie data with its own private
information, and then the reader will repeat the read until either the
cookie is cleared or it runs out of data.
The only real user of this is N_HDLC, which can use this to handle big
packets, even if the kernel buffer is smaller than the whole packet.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
During SSR after memory dump collection,BT controller will be powered off,
powered on and then FW will be downloaded.During suspend if BT controller
is powered off due to SSR then we should wait until SSR is completed and
then suspend.
Fixes: 2be43abac5a8 ("Bluetooth: hci_qca: Wait for timeout during suspend")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When __le32_to_cpu() fails, qca_memdump should be freed
just like when vmalloc() fails.
Fixes: d841502c79e3f ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
RTL8723DS could be handled by btrtl-driver, so add ability to bind it
using device tree.
Signed-off-by: John-Eric Kamps <johnny86@gmx.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
VID:PID -> 8087:0033
cat /sys/kernel/debug/usb/devices:
T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=03 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=0033 Rev= 0.00
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
btrtl_dev->ic_info is only available from the controller on cold boot
(the lmp subversion matches the device model and this is used to look up
the ic_info). On warm boots (firmware already loaded),
btrtl_dev->ic_info is null.
Fixes: 05672a2c14a4 (Bluetooth: btrtl: Enable central-peripheral role)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Enable the central-peripheral role on RTL8822CE. This enables creating
connections while there is an existing connection in the slave role.
This change can be confirmed in userspace via `bluetoothctl show` which
will now show "Roles: central-peripheral".
Reviewed-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The bt_dev_<level> macros already append a newline.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Switch and case where not properly aligned
Signed-off-by: Jagdish Tirumala <t.jag587@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
