| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
It's much easier to read register dumps if you read vertically
rather than horizontally, since the register numbers line up
and lead the eye down more than to the right.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This change enables unaligned userspace memory access via a kernel
fast path on tilegx. The kernel tracks user PC/instruction pairs
per-thread using a direct-mapped cache in userspace. The cache
maps those PC/instruction pairs to JIT'ed instruction sequences that
load or store using byte-wide load store intructions and then
synthesize 2-, 4- or 8-byte load or store results. Once an
instruction has been seen to generate an unaligned access once,
subsequent hits on that instruction typically require overhead
of only around 50 cycles if cache and TLB is hot.
We support the prctl() PR_GET_UNALIGN / PR_SET_UNALIGN sys call to
enable or disable unaligned fixups on a per-process basis.
To do this we pull some of the tilepro unaligned support out of the
single_step.c file; tilepro uses instruction disassembly for both
single-step and unaligned access support. Since tilegx actually has
hardware singlestep support, though, it's cleaner to keep the tilegx
unaligned access code in a separate file. While we're at it,
properly rename the tilepro-specific types, etc., to have tilepro
suffixes instead of generic tile suffixes.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
First, clean up active hardwalls in exit_thread(). This is a better
place than in arch_release_thread_info().
Second, mask out any non-online cpus from the cpumask after
validating any required semantics of the cpu set.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
show_regs() is inherently arch-dependent but it does make sense to print
generic debug information and some archs already do albeit in slightly
different forms. This patch introduces a generic function to print debug
information from show_regs() so that different archs print out the same
information and it's much easier to modify what's printed.
show_regs_print_info() prints out the same debug info as dump_stack()
does plus task and thread_info pointers.
* Archs which didn't print debug info now do.
alpha, arc, blackfin, c6x, cris, frv, h8300, hexagon, ia64, m32r,
metag, microblaze, mn10300, openrisc, parisc, score, sh64, sparc,
um, xtensa
* Already prints debug info. Replaced with show_regs_print_info().
The printed information is superset of what used to be there.
arm, arm64, avr32, mips, powerpc, sh32, tile, unicore32, x86
* s390 is special in that it used to print arch-specific information
along with generic debug info. Heiko and Martin think that the
arch-specific extra isn't worth keeping s390 specfic implementation.
Converted to use the generic version.
Note that now all archs print the debug info before actual register
dumps.
An example BUG() dump follows.
kernel BUG at /work/os/work/kernel/workqueue.c:4841!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #7
Hardware name: empty empty/S3992, BIOS 080011 10/26/2007
task: ffff88007c85e040 ti: ffff88007c860000 task.ti: ffff88007c860000
RIP: 0010:[<ffffffff8234a07e>] [<ffffffff8234a07e>] init_workqueues+0x4/0x6
RSP: 0000:ffff88007c861ec8 EFLAGS: 00010246
RAX: ffff88007c861fd8 RBX: ffffffff824466a8 RCX: 0000000000000001
RDX: 0000000000000046 RSI: 0000000000000001 RDI: ffffffff8234a07a
RBP: ffff88007c861ec8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff8234a07a
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88007dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff88015f7ff000 CR3: 00000000021f1000 CR4: 00000000000007f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffff88007c861ef8 ffffffff81000312 ffffffff824466a8 ffff88007c85e650
0000000000000003 0000000000000000 ffff88007c861f38 ffffffff82335e5d
ffff88007c862080 ffffffff8223d8c0 ffff88007c862080 ffffffff81c47760
Call Trace:
[<ffffffff81000312>] do_one_initcall+0x122/0x170
[<ffffffff82335e5d>] kernel_init_freeable+0x9b/0x1c8
[<ffffffff81c47760>] ? rest_init+0x140/0x140
[<ffffffff81c4776e>] kernel_init+0xe/0xf0
[<ffffffff81c6be9c>] ret_from_fork+0x7c/0xb0
[<ffffffff81c47760>] ? rest_init+0x140/0x140
...
v2: Typo fix in x86-32.
v3: CPU number dropped from show_regs_print_info() as
dump_stack_print_info() has been updated to print it. s390
specific implementation dropped as requested by s390 maintainers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile bits]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Link: http://lkml.kernel.org/r/20130321215235.348460344@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Using the new current_pt_regs() model, we can remove some trampolines
from assembly code and call directly to the C syscall implementations.
rt_sigreturn() and clone() still need some assembly wrapping, but no
longer are passed a pt_regs pointer. sigaltstack() and the
tilepro-specific cmpxchg_badaddr() syscalls are now just straight C.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Also provide an optimized current_pt_regs() while we're at it.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull tile arch update from Chris Metcalf:
"The bulk of this change is the tile uapi disintegration. There is
also a one-line change in here to enable interrupts in
do_work_pending() to avoid a WARN_ON in _local_bh_enable_ip()."
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: enable interrupts in do_work_pending()
UAPI: (Scripted) Disintegrate arch/tile/include/asm
UAPI: (Scripted) Disintegrate arch/tile/include/arch
|
|
getname() is intended to copy pathname strings from userspace into a
kernel buffer. The result is just a string in kernel space. It would
however be quite helpful to be able to attach some ancillary info to
the string.
For instance, we could attach some audit-related info to reduce the
amount of audit-related processing needed. When auditing is enabled,
we could also call getname() on the string more than once and not
need to recopy it from userspace.
This patchset converts the getname()/putname() interfaces to return
a struct instead of a string. For now, the struct just tracks the
string in kernel space and the original userland pointer for it.
Later, we'll add other information to the struct as it becomes
convenient.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
All the called functions expect interrupts to be enabled, and
now one of them has started to warn about it, so make it correct.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Pull second pile of signal handling patches from Al Viro:
"This one is just task_work_add() series + remaining prereqs for it.
There probably will be another pull request from that tree this
cycle - at least for helpers, to get them out of the way for per-arch
fixes remaining in the tree."
Fix trivial conflict in kernel/irq/manage.c: the merge of Andrew's pile
had brought in commit 97fd75b7b8e0 ("kernel/irq/manage.c: use the
pr_foo() infrastructure to prefix printks") which changed one of the
pr_err() calls that this merge moves around.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
keys: kill task_struct->replacement_session_keyring
keys: kill the dummy key_replace_session_keyring()
keys: change keyctl_session_to_parent() to use task_work_add()
genirq: reimplement exit_irq_thread() hook via task_work_add()
task_work_add: generic process-context callbacks
avr32: missed _TIF_NOTIFY_RESUME on one of do_notify_resume callers
parisc: need to check NOTIFY_RESUME when exiting from syscall
move key_repace_session_keyring() into tracehook_notify_resume()
TIF_NOTIFY_RESUME is defined on all targets now
|
|
Pull tile updates from Chris Metcalf:
"These changes cover a range of new arch/tile features and
optimizations. They've been through LKML review and on linux-next for
a month or so. There's also one bug-fix that just missed 3.4, which
I've marked for stable."
Fixed up trivial conflict in arch/tile/Kconfig (new added tile Kconfig
entries clashing with the generic timer/clockevents changes).
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: default to tilegx_defconfig for ARCH=tile
tile: fix bug where fls(0) was not returning 0
arch/tile: mark TILEGX as not EXPERIMENTAL
tile/mm/fault.c: Port OOM changes to handle_page_fault
arch/tile: add descriptive text if the kernel reports a bad trap
arch/tile: allow querying cpu module information from the hypervisor
arch/tile: fix hardwall for tilegx and generalize for idn and ipi
arch/tile: support multiple huge page sizes dynamically
mm: add new arch_make_huge_pte() method for tile support
arch/tile: support kexec() for tilegx
arch/tile: support <asm/cachectl.h> header for cacheflush() syscall
arch/tile: Allow tilegx to build with either 16K or 64K page size
arch/tile: optimize get_user/put_user and friends
arch/tile: support building big-endian kernel
arch/tile: allow building Linux with transparent huge pages enabled
arch/tile: use interrupt critical sections less
|
|
The hardwall drain code was not properly implemented for tilegx,
just tilepro, so you couldn't reliably restart an application that
made use of the udn.
In addition, the code was only applicable to the udn (user dynamic
network). On tilegx there is a second user network that is available
(the "idn"), and there is support for having I/O shims deliver
user-level interrupts to applications ("ipi") which functions in a
very similar way to the inter-core permissions used for udn/idn.
So this change also generalizes the code from supporting just the udn
to supports udn/idn/ipi on tilegx.
By default we now use /dev/hardwall/{udn,idn,ipi} with separate
minor numbers for the three devices.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smp hotplug cleanups from Thomas Gleixner:
"This series is merily a cleanup of code copied around in arch/* and
not changing any of the real cpu hotplug horrors yet. I wish I'd had
something more substantial for 3.5, but I underestimated the lurking
horror..."
Fix up trivial conflicts in arch/{arm,sparc,x86}/Kconfig and
arch/sparc/include/asm/thread_info_32.h
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
um: Remove leftover declaration of alloc_task_struct_node()
task_allocator: Use config switches instead of magic defines
sparc: Use common threadinfo allocator
score: Use common threadinfo allocator
sh-use-common-threadinfo-allocator
mn10300: Use common threadinfo allocator
powerpc: Use common threadinfo allocator
mips: Use common threadinfo allocator
hexagon: Use common threadinfo allocator
m32r: Use common threadinfo allocator
frv: Use common threadinfo allocator
cris: Use common threadinfo allocator
x86: Use common threadinfo allocator
c6x: Use common threadinfo allocator
fork: Provide kmemcache based thread_info allocator
tile: Use common threadinfo allocator
fork: Provide weak arch_release_[task_struct|thread_info] functions
fork: Move thread info gfp flags to header
fork: Remove the weak insanity
sh: Remove cpu_idle_wait()
...
|
|
First, we were at risk of handling thread-info flags, in particular
do_signal(), when returning from kernel space. This could happen
after a failed kernel_execve(), or when forking a kernel thread.
The fix is to test in do_work_pending() for user_mode() and return
immediately if so; we already had this test for one of the flags,
so I just hoisted it to the top of the function.
Second, if a ptraced process updated the callee-saved registers
in the ptregs struct and then processed another thread-info flag, we
would overwrite the modifications with the original callee-saved
registers. To fix this, we add a register to note if we've already
saved the registers once, and skip doing it on additional passes
through the loop. To avoid a performance hit from the couple of
extra instructions involved, I modified the GET_THREAD_INFO() macro
to be guaranteed to be one instruction, then bundled it with adjacent
instructions, yielding an overall net savings.
Reported-By: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Use the core allocator and deal with the extra cleanup in
arch_release_thread_info().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Link: http://lkml.kernel.org/r/20120505150142.311126440@linutronix.de
|
|
With lockstat we can end up trying to get a backtrace before
"high_memory" is initialized, so don't worry about range testing
if it is zero.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Commit bd119c69239322caafdb64517a806037d0d0c70a
"Disintegrate asm/system.h for Tile"
created the asm/switch_to.h file, but did not add an include
of it to all its users.
Also, commit b4816afa3986704d1404fc48e931da5135820472
"Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h"
introduced the concept of asm/cmpxchg.h but the tile arch
never got one. Fork the cmpxchg content out of the asm/atomic.h
file to create one.
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Disintegrate asm/system.h for Tile.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Coccinelle based conversion.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-24swm5zut3h9c4a6s46x8rws@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.
Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.
To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().
If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().
Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:
- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:
- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.
There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.
Split this function into:
- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.
- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).
To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().
This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
|
This support was partially present in the existing code (look for
"__tilegx__" ifdefs) but with this change you can build a working
kernel using the TILE-Gx toolchain and ARCH=tilegx.
Most of these files are new, generally adding a foo_64.c file
where previously there was just a foo_32.c file.
The ARCH=tilegx directive redirects to arch/tile, not arch/tilegx,
using the existing SRCARCH mechanism in the top-level Makefile.
Changes to existing files:
- <asm/bitops.h> and <asm/bitops_32.h> changed to factor the
include of <asm-generic/bitops/non-atomic.h> in the common header.
- <asm/compat.h> and arch/tile/kernel/compat.c changed to remove
the "const" markers I had put on compat_sys_execve() when trying
to match some recent similar changes to the non-compat execve.
It turns out the compat version wasn't "upgraded" to use const.
- <asm/opcode-tile_64.h> and <asm/opcode_constants_64.h> were
previously included accidentally, with the 32-bit contents. Now
they have the proper 64-bit contents.
Finally, I had to hack the existing hacky drivers/input/input-compat.h
to add yet another "#ifdef" for INPUT_COMPAT_TEST (same as x86_64).
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> [drivers/input]
|
|
This support is required for CONFIG_KEYS, NFSv4 kernel DNS, etc.
The change is slightly more complex than the minimal thing, since
I took advantage of having to go into the assembly code to just
move a bunch of stuff into C code: specifically, the schedule(),
do_async_page_fault(), do_signal(), and single_step_once() support,
in addition to the TIF_NOTIFY_RESUME support.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Add a node parameter to alloc_thread_info(), and change its name to
alloc_thread_info_node()
This change is needed to allow NUMA aware kthread_create_on_cpu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The Tilera architecture traditionally supports 64KB page sizes
to improve TLB utilization and improve performance when the
hardware is being used primarily to run a single application.
For more generic server scenarios, it can be beneficial to run
with 4KB page sizes, so this commit allows that to be specified
(by modifying the arch/tile/include/hv/pagesize.h header).
As part of this change, we also re-worked the PTE management
slightly so that PTE writes all go through a __set_pte() function
where we can do some additional validation. The set_pte_order()
function was eliminated since the "order" argument wasn't being used.
One bug uncovered was in the PCI DMA code, which wasn't properly
flushing the specified range. This was benign with 64KB pages,
but with 4KB pages we were getting some larger flushes wrong.
The per-cpu memory reservation code also needed updating to
conform with the newer percpu stuff; before it always chose 64KB,
and that was always correct, but with 4KB granularity we now have
to pay closer attention and reserve the amount of memory that will
be requested when the percpu code starts allocating.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
To handle single-step, tile mmap's a page of memory in the process
space for each thread and uses it to construct a version of the
instruction that we want to single step. If the process exec's,
though, we lose that mapping, and the kernel needs to be aware that
it will need to recreate it if the exec'ed process than tries to
single-step as well.
Also correct some int32_t to s32 for better kernel style.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Previously we were just setting up the "tp" register in the
new task as started by clone() in libc. However, this is not
quite right, since in principle a signal might be delivered to
the new task before it had its TLS set up. (Of course, this race
window still exists for resetting the libc getpid() cached value
in the new task, in principle. But in any case, we are now doing
this exactly the way all other architectures do it.)
This change is important for 2.6.37 since the tile glibc we will
be submitting upstream will not set TLS in user space any more,
so it will only work on a kernel that has this fix. It should
also be taken for 2.6.36.x in the stable tree if possible.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: stable <stable@kernel.org>
|
|
While not a port to KVM (yet), this change modifies the kernel
to be able to build either at PL1 or at PL2 with a suitable
config switch. Pushing up this change avoids handling branch
merge issues going forward with the KVM work.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
With this change we now include <asm-generic/syscalls.h> into the "tile"
version of the header. To take full advantage of the prototypes there,
we also change our naming convention for "struct pt_regs *" syscalls so
that, e.g., _sys_execve() is the "true" syscall entry, which sets the
appropriate register to point to the pt_regs before calling sys_execve().
While doing this I realized I no longer needed the fork and vfork
entry point stubs, since those functions aren't in the generic
syscall ABI, so I removed them as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This cut-and-paste bug was caused by rewriting the register dump
code to use only a single printk per line of output.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
During context switch, save and restore a couple of additional bits of
tilegx user state that can be persistently modified by userspace.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The sys_execve() implementation was properly const-ified but not
the declaration, the syscall wrappers, or the compat version.
This change completes the constification process.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Make do_execve() take a const filename pointer so that kernel_execve() compiles
correctly on ARM:
arch/arm/kernel/sys_arm.c:88: warning: passing argument 1 of 'do_execve' discards qualifiers from pointer target type
This also requires the argv and envp arguments to be consted twice, once for
the pointer array and once for the strings the array points to. This is
because do_execve() passes a pointer to the filename (now const) to
copy_strings_kernel(). A simpler alternative would be to cast the filename
pointer in do_execve() when it's passed to copy_strings_kernel().
do_execve() may not change any of the strings it is passed as part of the argv
or envp lists as they are some of them in .rodata, so marking these strings as
const should be fine.
Further kernel_execve() and sys_execve() need to be changed to match.
This has been test built on x86_64, frv, arm and mips.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This commit is primarily changes caused by reviewing "sparse"
and "checkpatch" output on our sources, so is somewhat noisy, since
things like "printk() -> pr_err()" (or whatever) throughout the
codebase tend to get tedious to read. Rather than trying to tease
apart precisely which things changed due to which type of code
review, this commit includes various cleanups in the code:
- sparse: Add declarations in headers for globals.
- sparse: Fix __user annotations.
- sparse: Using gfp_t consistently instead of int.
- sparse: removing functions not actually used.
- checkpatch: Clean up printk() warnings by using pr_info(), etc.;
also avoid partial-line printks except in bootup code.
- checkpatch: Use exposed structs rather than typedefs.
- checkpatch: Change some C99 comments to C89 comments.
In addition, a couple of minor other changes are rolled in
to this commit:
- Add support for a "raise" instruction to cause SIGFPE, etc., to be raised.
- Remove some compat code that is unnecessary when we fully eliminate
some of the deprecated syscalls from the generic syscall ABI.
- Update the tile_defconfig to reflect current config contents.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
It turns out there is some variance on the calling conventions for
these syscalls, and <asm-generic/syscalls.h> is already the mechanism
used to handle this. Switch arch/tile over to using that mechanism and
tweak the calling conventions for a couple of tile syscalls to match
<asm-generic/syscalls.h>.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This change is the core kernel support for TILEPro and TILE64 chips.
No driver support (except the console driver) is included yet.
This includes the relevant Linux headers in asm/; the low-level
low-level "Tile architecture" headers in arch/, which are
shared with the hypervisor, etc., and are build-system agnostic;
and the relevant hypervisor headers in hv/.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Paul Mundt <lethal@linux-sh.org>
|
