summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2015-07-21bcma: populate bus DT subnodes as platform_device-sRafał Miłecki1-0/+8
Our bus should allow defining children nodes as we may want to specify devices attached to the bus. This is required e.g. to specify NAND or ChipCommon cores and use bus's address and IRQ mappings. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: fix for p2p broken linkAniket Nagarnaik3-4/+29
This patch fixes following issues in p2p code paths. 1) bss role, bss type and connection type was not set correctly for p2p GO and p2p client at couple of places. 2) Driver appends a proprietary header to management frames which will be parsed by our firmware. Later while informing TX status to cfg80211, modified frame buffer was passed to cfg80211_mgmt_tx_status() instead of original one. Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21ath9k: make DMA stop related messages debug-onlyFelix Fietkau4-6/+12
A long time ago, ath9k had issues during reset where the DMA engine would stay active and could potentially corrupt memory. To debug those issues, the driver would print warnings whenever they occur. Nowadays, these issues are gone and the primary cause of these messages is if the MAC is stuck during reset or busy processing a long transmission. This is fairly harmless, yet these messages continue to worry users. To reduce the number of bogus bug reports, turn these messages into debug messages and count their occurence in the "reset" debugfs file. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21wlcore: sdio: return correct error codeRaphaël Poggi1-1/+2
When wlcore_probe_of failed, return the correct error code instead of ENOMEM Signed-off-by: Raphaël Poggi <poggi.raph@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21b43: Fix typo in function nameNik Nyby3-4/+4
This fixes a typo in the "b43_lo_g_maintenance_work" function name. Signed-off-by: Nik Nyby <nikolas@gnu.org> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Michael Buesch <m@bues.ch> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21rtlwifi: fix typo in commentsNik Nyby1-2/+2
This fixes a typo in two comments: "paht" -> "path". Signed-off-by: Nik Nyby <nikolas@gnu.org> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: usb: Fix double add error when submitting rx urbReyad Attiyat1-2/+4
There is an error that can occur where the driver adds the same URB to USB submission list twice. This happens since mwifiex_usb_submit_rem_rx can submit packets at same time as an rx urb complete callback. This causes list corruption and is fixed by not setting the skb to NULL when submitting an rx packet. [ 84.461242] WARNING: CPU: 1 PID: 748 at lib/list_debug.c:36 __list_add+0xcb/0xd0() [ 84.461245] list_add double add: new=ffff8800c92b0c50, prev=ffff8800c92b0c50, next=ffff8800ced6c430. [ 84.461247] Modules linked in: rfcomm fuse cmac nf_conntrack_netbios_ns nf_conntrack_broadcast ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack bnep iptable_mangle iptable_security iptable_raw btusb btintel bluetooth mwifiex_usb mwifiex x86_pkg_temp_thermal cfg80211 coretemp r8712u(C) kvm_intel kvm hid_sensor_als hid_sensor_incl_3d hid_sensor_rotation hid_sensor_magn_3d hid_sensor_accel_3d hid_sensor_gyro_3d hid_sensor_trigger hid_sensor_iio_common industrialio_triggered_buffer kfifo_buf rfkill iTCO_wdt industrialio iTCO_vendor_support [ 84.461316] crc32_pclmul crc32c_intel ghash_clmulni_intel microcode snd_hda_codec_realtek vfat snd_hda_codec_generic fat snd_hda_codec_hdmi snd_hda_intel snd_hda_controller uvcvideo snd_hda_codec videobuf2_vmalloc videobuf2_memops snd_hwdep videobuf2_core snd_hda_core joydev v4l2_common videodev hid_sensor_hub snd_seq hid_multitouch media snd_seq_device snd_pcm snd_timer mei_me snd i2c_i801 lpc_ich mei soundcore tpm_infineon tpm_tis tpm i2c_hid i2c_designware_platform i2c_designware_core nfsd auth_rpcgss nfs_acl lockd grace sunrpc sch_fq_codel i915 i2c_algo_bit drm_kms_helper drm xhci_pci xhci_hcd ehci_pci sd_mod ehci_hcd video [ 84.461383] CPU: 1 PID: 748 Comm: kworker/u9:0 Tainted: G C 4.1.0-rc5+ #163 [ 84.461386] Hardware name: Microsoft Corporation Surface Pro 2/Surface Pro 2, BIOS 2.05.0250 04/10/2015 [ 84.461396] Workqueue: MWIFIEX_RX_WORK_QUEUE mwifiex_rx_work_queue [mwifiex] [ 84.461399] ffffffff81a8150e ffff8801174cf8e8 ffffffff817df830 0000000000000000 [ 84.461405] ffff8801174cf938 ffff8801174cf928 ffffffff810a54ba ffff8800c86bd750 [ 84.461410] ffff8800c92b0c50 ffff8800c92b0c50 ffff8800ced6c430 ffff88010c057178 [ 84.461416] Call Trace: [ 84.461421] [<ffffffff817df830>] dump_stack+0x4f/0x7b [ 84.461428] [<ffffffff810a54ba>] warn_slowpath_common+0x8a/0xc0 [ 84.461432] [<ffffffff810a5536>] warn_slowpath_fmt+0x46/0x50 [ 84.461436] [<ffffffff814109fb>] __list_add+0xcb/0xd0 [ 84.461442] [<ffffffff815c551a>] ? usb_hcd_link_urb_to_ep+0x2a/0xa0 [ 84.461446] [<ffffffff815c5570>] usb_hcd_link_urb_to_ep+0x80/0xa0 [ 84.461459] [<ffffffffa004318a>] prepare_transfer+0xaa/0x130 [xhci_hcd] [ 84.461470] [<ffffffffa0044cf7>] xhci_queue_bulk_tx+0xb7/0x7a0 [xhci_hcd] [ 84.461480] [<ffffffffa003b67f>] ? xhci_urb_enqueue+0x50f/0x660 [xhci_hcd] [ 84.461489] [<ffffffffa003b67f>] ? xhci_urb_enqueue+0x50f/0x660 [xhci_hcd] [ 84.461498] [<ffffffffa003b735>] xhci_urb_enqueue+0x5c5/0x660 [xhci_hcd] [ 84.461503] [<ffffffff815c7ad3>] usb_hcd_submit_urb+0x93/0xa70 [ 84.461507] [<ffffffff8168dde8>] ? __alloc_skb+0x78/0x1f0 [ 84.461511] [<ffffffff8168d301>] ? __kmalloc_reserve.isra.26+0x31/0x90 [ 84.461515] [<ffffffff8168ddbc>] ? __alloc_skb+0x4c/0x1f0 [ 84.461519] [<ffffffff8168ddfc>] ? __alloc_skb+0x8c/0x1f0 [ 84.461523] [<ffffffff8168badd>] ? skb_dequeue+0x5d/0x80 [ 84.461527] [<ffffffff815c987e>] usb_submit_urb+0x42e/0x5f0 [ 84.461531] [<ffffffff816931d9>] ? __alloc_rx_skb+0x39/0x100 [ 84.461536] [<ffffffffa05aa372>] mwifiex_usb_submit_rx_urb+0xb2/0x170 [mwifiex_usb] [ 84.461542] [<ffffffffa05aa5f5>] mwifiex_usb_submit_rem_rx_urbs+0x45/0x50 [mwifiex_usb] [ 84.461550] [<ffffffffa07094be>] mwifiex_rx_work_queue+0x10e/0x140 [mwifiex] [ 84.461556] [<ffffffff810c4429>] process_one_work+0x229/0x890 [ 84.461559] [<ffffffff810c438c>] ? process_one_work+0x18c/0x890 [ 84.461565] [<ffffffff810c4ae3>] worker_thread+0x53/0x470 [ 84.461569] [<ffffffff810c4a90>] ? process_one_work+0x890/0x890 [ 84.461572] [<ffffffff810cb162>] kthread+0xf2/0x110 [ 84.461577] [<ffffffff811031ad>] ? trace_hardirqs_on+0xd/0x10 [ 84.461581] [<ffffffff810cb070>] ? kthread_create_on_node+0x230/0x230 [ 84.461586] [<ffffffff817e9662>] ret_from_fork+0x42/0x70 [ 84.461590] [<ffffffff810cb070>] ? kthread_create_on_node+0x230/0x230 [ 84.461593] ---[ end trace 65103af5e6fb3444 ]--- Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: fix leak of gen_ie storage on exit from mwifiex_del_mgmt_iesJohn Linville1-0/+1
Storage pointed to by gen_ie is allocated with kmalloc, but was never freed. Coverity CID #1271251 Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21MAINTAINERS: update for mwifiex driver maintainersAvinash Patil1-1/+1
Amit & Nishant would be taking care of maintaining mwifiex driver here onwards on account of organizational changes. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Frank Huang <frankh@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: do not short circuit exit from mwifiex_set_mgmt_iesJohn Linville1-0/+2
Without this change, the code simply exits after calling mwifiex_uap_set_head_tail_ies, leving the call to mwifiex_set_mgmt_beacon_data_ies as dead code. Coverity CID #1271292 Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: avoid freeing improper pointer in mwifiex_set_wowlan_mef_entryJohn Linville1-2/+6
mwifiex_set_wowlan_mef_entry attempts to free a passed-in pointer in case of an error. The only caller (mwifiex_set_mef_filter) passes that pointer as an offset into allocated memory, so any attempt to free that will not be the actual allocated pointer. Address this by changing mwifiex_set_wowlan_mef_entry to not do any free, and to cause mwifiex_set_mef_filter to do the appropriate free if the call to mwifiex_set_wowlan_mef_entry fails. Coverity CID #1295879 Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21wireless: cw1200: Remove redundant spi driver bus initializationAntonio Borneo1-1/+0
In ancient times it was necessary to manually initialize the bus field of an spi_driver to spi_bus_type. These days this is done in spi_register_driver(), so we can drop the manual assignment. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> To: Solomon Peachy <pizza@shaftnet.org> To: Kalle Valo <kvalo@codeaurora.org> To: linux-wireless@vger.kernel.org To: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: handle multichannel eventAvinash Patil4-0/+46
This patch adds support to handle multichannel event from FW. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: separate interface combination for multichannel and DFSAvinash Patil1-3/+22
Multichannel and DFS cannot be supported at same time. So when multichannel operation is enabled by module parameter, we enable number of channel as 2 while registering wiphy. For all other cases we advertise DFS support to cfg80211. Patch also adds support for radar detect widths parameter. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: advertise multichannel support to cfg80211Avinash Patil3-5/+23
This patch adds support to advetise mwifiex multichannel support to cfg80211. If module parameter drcs is enabled and FW supports multichannel operation we advertise this support to cfg80211. As of now 2 simultaneous channels are supported. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: support to set multichannel policy to FWAvinash Patil3-0/+40
This patch adds support for setting multichannel policy as module parameter to FW. Value of 1 indicates Multichannel support is enabled and value of 0 disables it. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: extend tx_data pause to AP interface as wellAvinash Patil3-34/+93
This patch adds support to extend TX Data pause for AP intefaces. Also for station role, support for pausing/unpausing all traffic when mac address parameter is BSSID is added. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: enable traffic only when port is openAvinash Patil7-3/+16
This patch adds support to enable data traffic only when port is open. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: support for bypass tx queueAvinash Patil6-2/+111
This patch adds support for another TX queue in driver- bypass TX queue. This queue is used for sending data/mgmt packets while in disconnected state i.e. when port is yet not unblocked. TDLS setup packets would also be queued in this queue. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: update domain_info upon band change in start_apAvinash Patil3-2/+9
It was observed that AP beacons would not reflect correct regulatory information upon starting AP in A band. This was because of missing AP config band update in set_channel of start_ap. Also we configure 11D settings info FW only for specific band. So we need to download domain info to FW even if domain remains unchanged but band is changed. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: add cfg80211 tdls channel switch handlerXinming Hu1-0/+72
This patch add cfg80211 tdls_chan_switch and tdls_cancel_chan_switch handler. With this handlers, mwifiex would support TDLS channel switch feature. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: enhance tdls link setup conditionXinming Hu4-7/+25
TDLS link status - channel switching, off channel or base channel itself indicates that TDLS link is setup. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: enable tdls channel switch ext_capXinming Hu1-0/+6
This patch enable tdls channel switch ext capability in tdls action frame, and also configure basic tdls channel switch parameters while tdls setup completed and tdls link is enabled.. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: add tdls config commandXinming Hu5-0/+166
This patch add support for a new tdls configuration command which is used for configuration of tdls channel switch parameters. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: process tdls channel switch eventXinming Hu4-1/+117
This patch add support for tdls channel switch event process. We block TX queues for particular RA list depending upon channel switch state. If channel switch state is moving to base channel, we unblock RA lists for AP. If channel switch state is moving to off channel, we unblock TDLS peer RA lists. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: add tdls channel switch statusXinming Hu4-2/+77
This patch add new tdls status used for tdls channel switch. Driver in turn would block cmd path and data path if tdls channel switching. Data path to non tdls peer should be blocked if tdls channel switch to off-channel. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: do not increase tx_pkts_queued if receive address tx pausedXinming Hu1-1/+4
If tx_pkts_queued is increased for tx paused receive address, tx process will be triggered for this packet. But since RA list was tx paused, there will be an infinite loop in mwifiex_wmm_process_tx waiting for the event(tx pause, tdls cs) to cancel tx pause. This will be an dead loop, since main_process was locked at this time, there will be no opportunity to process event. So do not increase tx_pkts_queued if receive address tx paused, this will be restored RA list is unpaused. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: block data traffic to tx paused receive addressXinming Hu1-1/+2
Data traffic to tx paused receive address should be blocked. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21mwifiex: add tx data pause supportAvinash Patil5-0/+118
This patch adds support to enable TX data pause feature for mwifiex. Whenever FW TX buffers reach threshold, FW would send TX pause event to driver. Driver in turn would block data traffic to that particular receiver address. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21rtlwifi: rtl8192cu: Remove rtl8723 codeTaehee Yoo3-36/+1
In the rtlwifi/rtl8192cu, rtl8723 code is dead code. So I remove it. Signed-off-by: Taehee Yoo <ap420073@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-21Merge ath-next from ath.git.Kalle Valo27-239/+3391
Major changes in ath10k: * enable VHT for IBSS * initial work to support qca99x0 and the corresponding 10.4 firmware branch
2015-07-11ath9k: DFS - add pulse chirp detection for FCCZefir Kurtisi1-6/+161
FCC long pulse radar (type 5) requires pulses to be checked for chirping. This patch implements chirp detection based on the FFT data provided for long pulses. A chirp is detected when a set of criteria defined by FCC pulse characteristics is met, including * have at least 4 FFT samples * max_bin index moves equidistantly between samples * the gradient is within defined range The chirp detection has been tested with reference radar generating devices and proved to work reliably. Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-11ath9k: DFS - consider ext_channel pulses only in HT40 modeZefir Kurtisi1-1/+2
The chip reports radar pulses on extension channel even if operating in HT20 mode. This patch adds a sanity check for HT40 mode before it feeds pulses on extension channel to the pattern detector. Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-11ipw2100: fix timeout bug - always evaluated to 0Nicholas Mc Guire1-1/+1
commit 2c86c275015c ("Add ipw2100 wireless driver.") introduced HW_PHY_OFF_LOOP_DELAY (HZ / 5000) which always evaluated to 0. Clarified by Stanislav Yakovlev <stas.yakovlev@gmail.com> that it should be 50 milliseconds thus fixed up to msecs_to_jiffies(50). Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-07-11ath10k: tweak interface combinationsMichal Kazior1-5/+34
Concurrent AP/GO operation on different channels isn't really supported well by the firmware so it's better to remove it from being advertised. Also tune the way station and p2p client interface limits are expressed to allow station + 2x p2p client or station + p2p client + p2p go. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-07-11ath10k: fix per-vif queue lockingMichal Kazior3-42/+45
Whenever any vdev was supposed to be paused all Tx queues were stopped (except offchannel) instead of only these associated with the given vdev. This caused subtle issues with multi-channel/multi-vif scenarios, e.g. authentication of station vif could sometimes fail depending on fw tx pause request timing. Fixes: b4aa539dd8f2 ("ath10k: implement tx pause wmi event") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-07-11ath10k: update vdev ps state on startMichal Kazior1-0/+8
Psmode can be forcefully enabled when vdev isn't started. It isn't guaranteed that mac80211 will re-issue psmode setting after vdev is started unless actual bss_conf.ps value has changed. Even if this doesn't fix any problems now it may prevent future breakage. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-07-11ath10k: fix hw roc expiration notifcationMichal Kazior2-3/+10
The expiration function must not be called when roc is explicitly cancelled by mac80211. However since fcf9844636be ("ath10k: fix hw roc expiration") the notification was never sent when roc actually expired. This fixes some P2P connection setup issues. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-07-11ath10k: limit multi-vif ps more aggresivellyMichal Kazior1-3/+3
Further testing proved that multi-channel AP+STA on QCA6174 with RM.2.0-00088 should have powersave force-disabled to avoid beacon misses/skipping on either side which in turn could disrupt communication. Since AP never has arvif->ps don't even bother checking it. Other combinations may be broken as well so disallow powersave with multivif outright unless firmware advertises otherwise. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-07-11ath10k: don't set cck/ofdm scan flagsMichal Kazior2-4/+0
mac80211 already does provide complete IEs for Probe Requests for hw scan and ath10k firmware was appending duplicate Supported Rates IEs unnecessarily. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-07-11ath10k: Fix target to cpu address conversion logicVasanthakumar Thiagarajan1-1/+1
In commit 418ca5992e2f ("ath10k: Make target cpu address to CE address conversion chip specific") mask 0x7fff is added by mistake instead of 0x7ff. Fix this regression. Fixes: 418ca5992e2f ("ath10k: Make target cpu address to CE address conversion chip specific") Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-07-11ath10k: fix QCA61X4 boot upBartosz Markowski1-1/+1
commit a521ee983d312db7 ("ath10k: Add new reg_address/mask to hw register table") broke QCA61x4 support by providing wrong fw_indicator_address, which should have been 0x0003a028 instead of 0x00009028. User experience was a failing boot up sequence (crashing device during initialization): [ 181.663874] ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002) [ 181.664787] ath10k_pci 0000:02:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0 [ 181.688886] ath10k_pci 0000:02:00.0: device has crashed during init [ 181.688897] ath10k_pci 0000:02:00.0: failed to wait for target after cold reset: -70 [ 181.688902] ath10k_pci 0000:02:00.0: failed to reset chip: -70 [ 181.689774] ath10k_pci: probe of 0000:02:00.0 failed with error -70 Fix it by updating the address with correct value. Fixes: a521ee983d31 ("ath10k: Add new reg_address/mask to hw register table") Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-07-10Merge branch 'be2net-next'David S. Miller5-42/+82
Sathya Perla says: ==================== be2net: patch set Hi David, the following patch set has code cleanup patches, minor enhancements and non-critical fixes. Pls consider applying to the net-next tree. Thanks! Patch 1 removes duplicate code in be_setup_wol() routine making it simpler and more readable. Patch 2 fixes the the bridge mode return value for the ndo_bridge_getlink() call. Instead of just relying on the SRIOV enabled state, the driver now queries the FW, for the actual mode of bridge. Patch 3 removes code for setting D0 power state as it's already done in pci_enable_device() Patch 4 fixes a bad return value in be_check_ufi_compatibility() routine introduced by an earlier commit. Patch 5 fixes a field in udp header being accessed while in network endian format. Patch 6 fixes the be_mcc_notify() routine to return an error status when the FW/HW is in an error state. Patch 7 fixes the be_cmd_rx_filter() routine to issue the RX_FILTER cmd and not wait for a completion from the FW. If the FW/adapter is in an error state, this change helps in not holding up the rtnl_lock and keeping bottom halves disabled while the driver timesout waiting for a response from the FW. Patch 8 fixes the be_cmd_set_loopback() routine to issue the LOOPBACK cmd and not wait for the FW completion while spin_lock_bh() is held on the mcc_lock. As the cmd is always issued from ethtool in a process context, it can sleep till the FW completion is received. Patch 9 bumps up the driver version to 10.6.0.3 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-10be2net: bump up the driver version to 10.6.0.3Sathya Perla1-1/+1
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-10be2net: make SET_LOOPBACK_MODE cmd asynchrounousSuresh Reddy3-5/+35
The SET_LOOPBACK_MODE command is always issued from ethtool only in a process context. So, while waiting for the cmd to complete, the driver can sleep instead of holding spin_lock_bh() on the mcc_lock. This is done by calling be_mcc_notify() instead of be_mcc_notify_wait() (that returns only after the cmd completes while the MCCQ is locked). Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-10be2net: make the RX_FILTER command asynchronousSuresh Reddy1-1/+1
This fix makes the RX_FILTER cmd asynchronous, i.e., the caller issues this cmd and doesn't wait for a completion from the FW. If the FW/adapter is in an error state, this change helps in not holding up the rtnl_lock and keeping bottom halves disabled while the driver timesout waiting for a response from the FW. Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-10be2net: return error status from be_mcc_notify()Suresh Reddy1-11/+28
When the adapter is in error state, return error from be_mcc_notify() so that the caller routines need not sleep waiting for a response. Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-10be2net: convert dest field in udp-hdr to host-endianVenkat Duvvuru1-1/+1
The "dest" field in the UDP-hdr of a TX skb is in network endian format. Convert it to host endian before accessing it. The os2bmc patch, mentioned below introduced this code. Fixes: 760c295e0e8d ("be2net: Support for OS2BMC") Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-10be2net: fix wrong return value in be_check_ufi_compatibility()Vasundhara Volam1-1/+1
In the commit a6e6ff6eee12f3e ("be2net: simplify UFI compatibility checking"), a return value of "-1" was incorrectly used in place of "false". This patch fixes it. Fixes: a6e6ff6eee12f3e ("be2net: simplify UFI compatibility checking") Signed-off-by: Vasundhara Volam <vasundhara.volam@avagotech.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-10be2net: remove redundant D0 power state setKalesh Purayil1-2/+0
pci_enable_device() call sets device power state to D0; there is no need doing it again. Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com> Signed-off-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-01 10:38:38 +0000