diff options
Diffstat (limited to 'Documentation/hwmon')
| -rw-r--r-- | Documentation/hwmon/w83791d | 113 |
1 files changed, 113 insertions, 0 deletions
diff --git a/Documentation/hwmon/w83791d b/Documentation/hwmon/w83791d new file mode 100644 index 000000000000..83a3836289c2 --- /dev/null +++ b/Documentation/hwmon/w83791d @@ -0,0 +1,113 @@ +Kernel driver w83791d +===================== + +Supported chips: + * Winbond W83791D + Prefix: 'w83791d' + Addresses scanned: I2C 0x2c - 0x2f + Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83791Da.pdf + +Author: Charles Spirakis <bezaur@gmail.com> + +This driver was derived from the w83781d.c and w83792d.c source files. + +Credits: + w83781d.c: + Frodo Looijaard <frodol@dds.nl>, + Philip Edelbrock <phil@netroedge.com>, + and Mark Studebaker <mdsxyz123@yahoo.com> + w83792d.c: + Chunhao Huang <DZShen@Winbond.com.tw>, + Rudolf Marek <r.marek@sh.cvut.cz> + +Module Parameters +----------------- + +* init boolean + (default 0) + Use 'init=1' to have the driver do extra software initializations. + The default behavior is to do the minimum initialization possible + and depend on the BIOS to properly setup the chip. If you know you + have a w83791d and you're having problems, try init=1 before trying + reset=1. + +* reset boolean + (default 0) + Use 'reset=1' to reset the chip (via index 0x40, bit 7). The default + behavior is no chip reset to preserve BIOS settings. + +* force_subclients=bus,caddr,saddr,saddr + This is used to force the i2c addresses for subclients of + a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b' + to force the subclients of chip 0x2f on bus 0 to i2c addresses + 0x4a and 0x4b. + + +Description +----------- + +This driver implements support for the Winbond W83791D chip. + +Detection of the chip can sometimes be foiled because it can be in an +internal state that allows no clean access (Bank with ID register is not +currently selected). If you know the address of the chip, use a 'force' +parameter; this will put it into a more well-behaved state first. + +The driver implements three temperature sensors, five fan rotation speed +sensors, and ten voltage sensors. + +Temperatures are measured in degrees Celsius and measurement resolution is 1 +degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when +the temperature gets higher than the Overtemperature Shutdown value; it stays +on until the temperature falls below the Hysteresis value. + +Fan rotation speeds are reported in RPM (rotations per minute). An alarm is +triggered if the rotation speed has dropped below a programmable limit. Fan +readings can be divided by a programmable divider (1, 2, 4, 8 for fan 1/2/3 +and 1, 2, 4, 8, 16, 32, 64 or 128 for fan 4/5) to give the readings more +range or accuracy. + +Voltage sensors (also known as IN sensors) report their values in millivolts. +An alarm is triggered if the voltage has crossed a programmable minimum +or maximum limit. + +Alarms are provided as output from a "realtime status register". The +following bits are defined: + +bit - alarm on: +0 - Vcore +1 - VINR0 +2 - +3.3VIN +3 - 5VDD +4 - temp1 +5 - temp2 +6 - fan1 +7 - fan2 +8 - +12VIN +9 - -12VIN +10 - -5VIN +11 - fan3 +12 - chassis +13 - temp3 +14 - VINR1 +15 - reserved +16 - tart1 +17 - tart2 +18 - tart3 +19 - VSB +20 - VBAT +21 - fan4 +22 - fan5 +23 - reserved + +When an alarm goes off, you can be warned by a beeping signal through your +computer speaker. It is possible to enable all beeping globally, or only +the beeping for some alarms. + +The driver only reads the chip values each 3 seconds; reading them more +often will do no harm, but will return 'old' values. + +W83791D TODO: +--------------- +Provide a patch for per-file alarms as discussed on the mailing list +Provide a patch for smart-fan control (still need appropriate motherboard/fans) |