diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci/rockchip-pcie.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/pci/rockchip-pcie.txt | 28 |
1 files changed, 25 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt index 1453a734c2f5..af34c65773fd 100644 --- a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt @@ -19,8 +19,6 @@ Required properties: - "pm" - msi-map: Maps a Requester ID to an MSI controller and associated msi-specifier data. See ./pci-msi.txt -- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. -- phy-names: MUST be "pcie-phy". - interrupts: Three interrupt entries must be specified. - interrupt-names: Must include the following names - "sys" @@ -42,11 +40,24 @@ Required properties: interrupt source. The value must be 1. - interrupt-map-mask and interrupt-map: standard PCI properties +Required properties for legacy PHY model (deprecated): +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. +- phy-names: MUST be "pcie-phy". + +Required properties for per-lane PHY model (preferred): +- phys: Must contain an phandle to a PHY for each entry in phy-names. +- phy-names: Must include 4 entries for all 4 lanes even if some of + them won't be used for your cases. Entries are of the form "pcie-phy-N": + where N ranges from 0 to 3. + (see example below and you MUST also refer to ../phy/rockchip-pcie-phy.txt + for changing the #phy-cells of phy node to support it) + Optional Property: - aspm-no-l0s: RC won't support ASPM L0s. This property is needed if using 24MHz OSC for RC's PHY. -- ep-gpios: contain the entry for pre-reset gpio +- ep-gpios: contain the entry for pre-reset GPIO - num-lanes: number of lanes to use +- vpcie12v-supply: The phandle to the 12v regulator to use for PCIe. - vpcie3v3-supply: The phandle to the 3.3v regulator to use for PCIe. - vpcie1v8-supply: The phandle to the 1.8v regulator to use for PCIe. - vpcie0v9-supply: The phandle to the 0.9v regulator to use for PCIe. @@ -95,6 +106,7 @@ pcie0: pcie@f8000000 { <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, <&cru SRST_A_PCIE>; reset-names = "core", "mgmt", "mgmt-sticky", "pipe", "pm", "pclk", "aclk"; + /* deprecated legacy PHY model */ phys = <&pcie_phy>; phy-names = "pcie-phy"; pinctrl-names = "default"; @@ -111,3 +123,13 @@ pcie0: pcie@f8000000 { #interrupt-cells = <1>; }; }; + +pcie0: pcie@f8000000 { + ... + + /* preferred per-lane PHY model */ + phys = <&pcie_phy 0>, <&pcie_phy 1>, <&pcie_phy 2>, <&pcie_phy 3>; + phy-names = "pcie-phy-0", "pcie-phy-1", "pcie-phy-2", "pcie-phy-3"; + + ... +}; |