diff options
| -rw-r--r-- | arch/sh/boards/mach-ecovec24/setup.c | 97 |
1 files changed, 95 insertions, 2 deletions
diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c index 826e62326d51..cfd958c613d4 100644 --- a/arch/sh/boards/mach-ecovec24/setup.c +++ b/arch/sh/boards/mach-ecovec24/setup.c @@ -19,6 +19,10 @@ #include <linux/usb/r8a66597.h> #include <linux/i2c.h> #include <linux/i2c/tsc2007.h> +#include <linux/spi/spi.h> +#include <linux/spi/sh_msiof.h> +#include <linux/spi/mmc_spi.h> +#include <linux/mmc/host.h> #include <linux/input.h> #include <linux/input/sh_keysc.h> #include <linux/mfd/sh_mobile_sdhi.h> @@ -421,6 +425,7 @@ static struct i2c_board_info ts_i2c_clients = { .irq = IRQ0, }; +#ifdef CONFIG_MFD_SH_MOBILE_SDHI /* SHDI0 */ static void sdhi0_set_pwr(struct platform_device *pdev, int state) { @@ -493,6 +498,73 @@ static struct platform_device sdhi1_device = { }, }; +#else + +static int mmc_spi_get_ro(struct device *dev) +{ + return gpio_get_value(GPIO_PTY6); +} + +static int mmc_spi_get_cd(struct device *dev) +{ + return !gpio_get_value(GPIO_PTY7); +} + +static void mmc_spi_setpower(struct device *dev, unsigned int maskval) +{ + gpio_set_value(GPIO_PTB6, maskval ? 1 : 0); +} + +static struct mmc_spi_platform_data mmc_spi_info = { + .get_ro = mmc_spi_get_ro, + .get_cd = mmc_spi_get_cd, + .caps = MMC_CAP_NEEDS_POLL, + .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, /* 3.3V only */ + .setpower = mmc_spi_setpower, +}; + +static struct spi_board_info spi_bus[] = { + { + .modalias = "mmc_spi", + .platform_data = &mmc_spi_info, + .max_speed_hz = 5000000, + .mode = SPI_MODE_0, + .controller_data = (void *) GPIO_PTM4, + }, +}; + +static struct sh_msiof_spi_info msiof0_data = { + .num_chipselect = 1, +}; + +static struct resource msiof0_resources[] = { + [0] = { + .name = "MSIOF0", + .start = 0xa4c40000, + .end = 0xa4c40063, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = 84, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device msiof0_device = { + .name = "spi_sh_msiof", + .id = 0, /* MSIOF0 */ + .dev = { + .platform_data = &msiof0_data, + }, + .num_resources = ARRAY_SIZE(msiof0_resources), + .resource = msiof0_resources, + .archdata = { + .hwblk_id = HWBLK_MSIOF0, + }, +}; + +#endif + static struct platform_device *ecovec_devices[] __initdata = { &heartbeat_device, &nor_flash_device, @@ -503,8 +575,12 @@ static struct platform_device *ecovec_devices[] __initdata = { &ceu0_device, &ceu1_device, &keysc_device, +#ifdef CONFIG_MFD_SH_MOBILE_SDHI &sdhi0_device, &sdhi1_device, +#else + &msiof0_device, +#endif }; #define EEPROM_ADDR 0x50 @@ -773,7 +849,8 @@ static int __init arch_setup(void) gpio_direction_input(GPIO_PTR5); gpio_direction_input(GPIO_PTR6); - /* enable SDHI0 (needs DS2.4 set to ON) */ +#ifdef CONFIG_MFD_SH_MOBILE_SDHI + /* enable SDHI0 on CN11 (needs DS2.4 set to ON) */ gpio_request(GPIO_FN_SDHI0CD, NULL); gpio_request(GPIO_FN_SDHI0WP, NULL); gpio_request(GPIO_FN_SDHI0CMD, NULL); @@ -785,7 +862,7 @@ static int __init arch_setup(void) gpio_request(GPIO_PTB6, NULL); gpio_direction_output(GPIO_PTB6, 0); - /* enable SDHI1 (needs DS2.6,7 set to ON,OFF) */ + /* enable SDHI1 on CN12 (needs DS2.6,7 set to ON,OFF) */ gpio_request(GPIO_FN_SDHI1CD, NULL); gpio_request(GPIO_FN_SDHI1WP, NULL); gpio_request(GPIO_FN_SDHI1CMD, NULL); @@ -799,6 +876,22 @@ static int __init arch_setup(void) /* I/O buffer drive ability is high for SDHI1 */ ctrl_outw((ctrl_inw(IODRIVEA) & ~0x3000) | 0x2000 , IODRIVEA); +#else + /* enable MSIOF0 on CN11 (needs DS2.4 set to OFF) */ + gpio_request(GPIO_FN_MSIOF0_TXD, NULL); + gpio_request(GPIO_FN_MSIOF0_RXD, NULL); + gpio_request(GPIO_FN_MSIOF0_TSCK, NULL); + gpio_request(GPIO_PTM4, NULL); /* software CS control of TSYNC pin */ + gpio_direction_output(GPIO_PTM4, 1); /* active low CS */ + gpio_request(GPIO_PTB6, NULL); /* 3.3V power control */ + gpio_direction_output(GPIO_PTB6, 0); /* disable power by default */ + gpio_request(GPIO_PTY6, NULL); /* write protect */ + gpio_direction_input(GPIO_PTY6); + gpio_request(GPIO_PTY7, NULL); /* card detect */ + gpio_direction_input(GPIO_PTY7); + + spi_register_board_info(spi_bus, ARRAY_SIZE(spi_bus)); +#endif /* enable I2C device */ i2c_register_board_info(1, i2c1_devices, |