Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 369 insertions, 0 deletions

diff --git a/drivers/ide/pci/trm290.c b/drivers/ide/pci/trm290.c
new file mode 100644
index 000000000000..8b5eea5405ef
--- /dev/null
+++ b/drivers/ide/pci/trm290.c
@@ -0,0 +1,369 @@
+/*
+ *  linux/drivers/ide/pci/trm290.c		Version 1.02	Mar. 18, 2000
+ *
+ *  Copyright (c) 1997-1998  Mark Lord
+ *  May be copied or modified under the terms of the GNU General Public License
+ *
+ *  June 22, 2004 - get rid of check_region
+ *                  Jesper Juhl <juhl-lkml@dif.dk>
+ *
+ */
+
+/*
+ * This module provides support for the bus-master IDE DMA function
+ * of the Tekram TRM290 chip, used on a variety of PCI IDE add-on boards,
+ * including a "Precision Instruments" board.  The TRM290 pre-dates
+ * the sff-8038 standard (ide-dma.c) by a few months, and differs
+ * significantly enough to warrant separate routines for some functions,
+ * while re-using others from ide-dma.c.
+ *
+ * EXPERIMENTAL!  It works for me (a sample of one).
+ *
+ * Works reliably for me in DMA mode (READs only),
+ * DMA WRITEs are disabled by default (see #define below);
+ *
+ * DMA is not enabled automatically for this chipset,
+ * but can be turned on manually (with "hdparm -d1") at run time.
+ *
+ * I need volunteers with "spare" drives for further testing
+ * and development, and maybe to help figure out the peculiarities.
+ * Even knowing the registers (below), some things behave strangely.
+ */
+
+#define TRM290_NO_DMA_WRITES	/* DMA writes seem unreliable sometimes */
+
+/*
+ * TRM-290 PCI-IDE2 Bus Master Chip
+ * ================================
+ * The configuration registers are addressed in normal I/O port space
+ * and are used as follows:
+ *
+ * trm290_base depends on jumper settings, and is probed for by ide-dma.c
+ *
+ * trm290_base+2 when WRITTEN: chiptest register (byte, write-only)
+ *	bit7 must always be written as "1"
+ *	bits6-2 undefined
+ *	bit1 1=legacy_compatible_mode, 0=native_pci_mode
+ *	bit0 1=test_mode, 0=normal(default)
+ *
+ * trm290_base+2 when READ: status register (byte, read-only)
+ *	bits7-2 undefined
+ *	bit1 channel0 busmaster interrupt status 0=none, 1=asserted
+ *	bit0 channel0 interrupt status 0=none, 1=asserted
+ *
+ * trm290_base+3 Interrupt mask register
+ *	bits7-5 undefined
+ *	bit4 legacy_header: 1=present, 0=absent
+ *	bit3 channel1 busmaster interrupt status 0=none, 1=asserted (read only)
+ *	bit2 channel1 interrupt status 0=none, 1=asserted (read only)
+ *	bit1 channel1 interrupt mask: 1=masked, 0=unmasked(default)
+ *	bit0 channel0 interrupt mask: 1=masked, 0=unmasked(default)
+ *
+ * trm290_base+1 "CPR" Config Pointer Register (byte)
+ *	bit7 1=autoincrement CPR bits 2-0 after each access of CDR
+ *	bit6 1=min. 1 wait-state posted write cycle (default), 0=0 wait-state
+ *	bit5 0=enabled master burst access (default), 1=disable  (write only)
+ *	bit4 PCI DEVSEL# timing select: 1=medium(default), 0=fast
+ *	bit3 0=primary IDE channel, 1=secondary IDE channel
+ *	bits2-0 register index for accesses through CDR port
+ *
+ * trm290_base+0 "CDR" Config Data Register (word)
+ *	two sets of seven config registers,
+ *	selected by CPR bit 3 (channel) and CPR bits 2-0 (index 0 to 6),
+ *	each index defined below:
+ *
+ * Index-0 Base address register for command block (word)
+ *	defaults: 0x1f0 for primary, 0x170 for secondary
+ *
+ * Index-1 general config register (byte)
+ *	bit7 1=DMA enable, 0=DMA disable
+ *	bit6 1=activate IDE_RESET, 0=no action (default)
+ *	bit5 1=enable IORDY, 0=disable IORDY (default)
+ *	bit4 0=16-bit data port(default), 1=8-bit (XT) data port
+ *	bit3 interrupt polarity: 1=active_low, 0=active_high(default)
+ *	bit2 power-saving-mode(?): 1=enable, 0=disable(default) (write only)
+ *	bit1 bus_master_mode(?): 1=enable, 0=disable(default)
+ *	bit0 enable_io_ports: 1=enable(default), 0=disable
+ *
+ * Index-2 read-ahead counter preload bits 0-7 (byte, write only)
+ *	bits7-0 bits7-0 of readahead count
+ *
+ * Index-3 read-ahead config register (byte, write only)
+ *	bit7 1=enable_readahead, 0=disable_readahead(default)
+ *	bit6 1=clear_FIFO, 0=no_action
+ *	bit5 undefined
+ *	bit4 mode4 timing control: 1=enable, 0=disable(default)
+ *	bit3 undefined
+ *	bit2 undefined
+ *	bits1-0 bits9-8 of read-ahead count
+ *
+ * Index-4 base address register for control block (word)
+ *	defaults: 0x3f6 for primary, 0x376 for secondary
+ *
+ * Index-5 data port timings (shared by both drives) (byte)
+ *	standard PCI "clk" (clock) counts, default value = 0xf5
+ *
+ *	bits7-6 setup time:  00=1clk, 01=2clk, 10=3clk, 11=4clk
+ *	bits5-3 hold time:	000=1clk, 001=2clk, 010=3clk,
+ *				011=4clk, 100=5clk, 101=6clk,
+ *				110=8clk, 111=12clk
+ *	bits2-0 active time:	000=2clk, 001=3clk, 010=4clk,
+ *				011=5clk, 100=6clk, 101=8clk,
+ *				110=12clk, 111=16clk
+ *
+ * Index-6 command/control port timings (shared by both drives) (byte)
+ *	same layout as Index-5, default value = 0xde
+ *
+ * Suggested CDR programming for PIO mode0 (600ns):
+ *	0x01f0,0x21,0xff,0x80,0x03f6,0xf5,0xde	; primary
+ *	0x0170,0x21,0xff,0x80,0x0376,0xf5,0xde	; secondary
+ *
+ * Suggested CDR programming for PIO mode3 (180ns):
+ *	0x01f0,0x21,0xff,0x80,0x03f6,0x09,0xde	; primary
+ *	0x0170,0x21,0xff,0x80,0x0376,0x09,0xde	; secondary
+ *
+ * Suggested CDR programming for PIO mode4 (120ns):
+ *	0x01f0,0x21,0xff,0x80,0x03f6,0x00,0xde	; primary
+ *	0x0170,0x21,0xff,0x80,0x0376,0x00,0xde	; secondary
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/ioport.h>
+#include <linux/interrupt.h>
+#include <linux/blkdev.h>
+#include <linux/init.h>
+#include <linux/hdreg.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/ide.h>
+
+#include <asm/io.h>
+
+static void trm290_prepare_drive (ide_drive_t *drive, unsigned int use_dma)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	u16 reg = 0;
+	unsigned long flags;
+
+	/* select PIO or DMA */
+	reg = use_dma ? (0x21 | 0x82) : (0x21 & ~0x82);
+
+	local_irq_save(flags);
+
+	if (reg != hwif->select_data) {
+		hwif->select_data = reg;
+		/* set PIO/DMA */
+		hwif->OUTB(0x51|(hwif->channel<<3), hwif->config_data+1);
+		hwif->OUTW(reg & 0xff, hwif->config_data);
+	}
+
+	/* enable IRQ if not probing */
+	if (drive->present) {
+		reg = hwif->INW(hwif->config_data + 3);
+		reg &= 0x13;
+		reg &= ~(1 << hwif->channel);
+		hwif->OUTW(reg, hwif->config_data+3);
+	}
+
+	local_irq_restore(flags);
+}
+
+static void trm290_selectproc (ide_drive_t *drive)
+{
+	trm290_prepare_drive(drive, drive->using_dma);
+}
+
+#ifdef CONFIG_BLK_DEV_IDEDMA
+static void trm290_ide_dma_exec_cmd(ide_drive_t *drive, u8 command)
+{
+	ide_hwif_t *hwif	= HWIF(drive);
+
+	if (HWGROUP(drive)->handler != NULL)	/* paranoia check */
+		BUG();
+	ide_set_handler(drive, &ide_dma_intr, WAIT_CMD, NULL);
+	/* issue cmd to drive */
+	hwif->OUTB(command, IDE_COMMAND_REG);
+}
+
+static int trm290_ide_dma_setup(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct request *rq = hwif->hwgroup->rq;
+	unsigned int count, rw;
+
+	if (rq_data_dir(rq)) {
+#ifdef TRM290_NO_DMA_WRITES
+		/* always use PIO for writes */
+		trm290_prepare_drive(drive, 0);	/* select PIO xfer */
+		return 1;
+#endif
+		rw = 1;
+	} else
+		rw = 2;
+
+	if (!(count = ide_build_dmatable(drive, rq))) {
+		/* try PIO instead of DMA */
+		trm290_prepare_drive(drive, 0); /* select PIO xfer */
+		return 1;
+	}
+	/* select DMA xfer */
+	trm290_prepare_drive(drive, 1);
+	hwif->OUTL(hwif->dmatable_dma|rw, hwif->dma_command);
+	drive->waiting_for_dma = 1;
+	/* start DMA */
+	hwif->OUTW((count * 2) - 1, hwif->dma_status);
+	return 0;
+}
+
+static void trm290_ide_dma_start(ide_drive_t *drive)
+{
+}
+
+static int trm290_ide_dma_end (ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	u16 status = 0;
+
+	drive->waiting_for_dma = 0;
+	/* purge DMA mappings */
+	ide_destroy_dmatable(drive);
+	status = hwif->INW(hwif->dma_status);
+	return (status != 0x00ff);
+}
+
+static int trm290_ide_dma_test_irq (ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	u16 status = 0;
+
+	status = hwif->INW(hwif->dma_status);
+	return (status == 0x00ff);
+}
+#endif /* CONFIG_BLK_DEV_IDEDMA */
+
+/*
+ * Invoked from ide-dma.c at boot time.
+ */
+static void __devinit init_hwif_trm290(ide_hwif_t *hwif)
+{
+	unsigned int cfgbase = 0;
+	unsigned long flags;
+	u8 reg = 0;
+	struct pci_dev *dev = hwif->pci_dev;
+
+	hwif->no_lba48 = 1;
+	hwif->chipset = ide_trm290;
+	cfgbase = pci_resource_start(dev, 4);
+	if ((dev->class & 5) && cfgbase) {
+		hwif->config_data = cfgbase;
+		printk(KERN_INFO "TRM290: chip config base at 0x%04lx\n",
+			hwif->config_data);
+	} else {
+		hwif->config_data = 0x3df0;
+		printk(KERN_INFO "TRM290: using default config base at 0x%04lx\n",
+			hwif->config_data);
+	}
+
+	local_irq_save(flags);
+	/* put config reg into first byte of hwif->select_data */
+	hwif->OUTB(0x51|(hwif->channel<<3), hwif->config_data+1);
+	/* select PIO as default */
+	hwif->select_data = 0x21;
+	hwif->OUTB(hwif->select_data, hwif->config_data);
+	/* get IRQ info */
+	reg = hwif->INB(hwif->config_data+3);
+	/* mask IRQs for both ports */
+	reg = (reg & 0x10) | 0x03;
+	hwif->OUTB(reg, hwif->config_data+3);
+	local_irq_restore(flags);
+
+	if ((reg & 0x10))
+		/* legacy mode */
+		hwif->irq = hwif->channel ? 15 : 14;
+	else if (!hwif->irq && hwif->mate && hwif->mate->irq)
+		/* sharing IRQ with mate */
+		hwif->irq = hwif->mate->irq;
+
+	ide_setup_dma(hwif, (hwif->config_data + 4) ^ (hwif->channel ? 0x0080 : 0x0000), 3);
+
+#ifdef CONFIG_BLK_DEV_IDEDMA
+	hwif->dma_setup = &trm290_ide_dma_setup;
+	hwif->dma_exec_cmd = &trm290_ide_dma_exec_cmd;
+	hwif->dma_start = &trm290_ide_dma_start;
+	hwif->ide_dma_end = &trm290_ide_dma_end;
+	hwif->ide_dma_test_irq = &trm290_ide_dma_test_irq;
+#endif /* CONFIG_BLK_DEV_IDEDMA */
+
+	hwif->selectproc = &trm290_selectproc;
+	hwif->autodma = 0;		/* play it safe for now */
+	hwif->drives[0].autodma = hwif->autodma;
+	hwif->drives[1].autodma = hwif->autodma;
+#if 1
+	{
+	/*
+	 * My trm290-based card doesn't seem to work with all possible values
+	 * for the control basereg, so this kludge ensures that we use only
+	 * values that are known to work.  Ugh.		-ml
+	 */
+		u16 new, old, compat = hwif->channel ? 0x374 : 0x3f4;
+		static u16 next_offset = 0;
+		u8 old_mask;
+
+		hwif->OUTB(0x54|(hwif->channel<<3), hwif->config_data+1);
+		old = hwif->INW(hwif->config_data);
+		old &= ~1;
+		old_mask = hwif->INB(old+2);
+		if (old != compat && old_mask == 0xff) {
+			/* leave lower 10 bits untouched */
+			compat += (next_offset += 0x400);
+			hwif->io_ports[IDE_CONTROL_OFFSET] = compat + 2;
+			hwif->OUTW(compat|1, hwif->config_data);
+			new = hwif->INW(hwif->config_data);
+			printk(KERN_INFO "%s: control basereg workaround: "
+				"old=0x%04x, new=0x%04x\n",
+				hwif->name, old, new & ~1);
+		}
+	}
+#endif
+}
+
+static ide_pci_device_t trm290_chipset __devinitdata = {
+	.name		= "TRM290",
+	.init_hwif	= init_hwif_trm290,
+	.channels	= 2,
+	.autodma	= NOAUTODMA,
+	.bootable	= ON_BOARD,
+};
+
+static int __devinit trm290_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	return ide_setup_pci_device(dev, &trm290_chipset);
+}
+
+static struct pci_device_id trm290_pci_tbl[] = {
+	{ PCI_VENDOR_ID_TEKRAM, PCI_DEVICE_ID_TEKRAM_DC290, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+	{ 0, },
+};
+MODULE_DEVICE_TABLE(pci, trm290_pci_tbl);
+
+static struct pci_driver driver = {
+	.name		= "TRM290_IDE",
+	.id_table	= trm290_pci_tbl,
+	.probe		= trm290_init_one,
+};
+
+static int trm290_ide_init(void)
+{
+	return ide_pci_register_driver(&driver);
+}
+
+module_init(trm290_ide_init);
+
+MODULE_AUTHOR("Mark Lord");
+MODULE_DESCRIPTION("PCI driver module for Tekram TRM290 IDE");
+MODULE_LICENSE("GPL");