Merge tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux

Pull clk updates from Michael Turquette:
 "The clk framework changes for 4.3 are mostly updates to existing
  drivers and the addition of new clock drivers.  Stephen Boyd has also
  done a lot of subsystem-wide driver clean-ups (thanks!).  There are
  also fixes to the framework core and changes to better split clock
  provider drivers from clock consumer drivers"

* tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
  clk: s5pv210: add missing call to samsung_clk_of_add_provider()
  clk: pistachio: correct critical clock list
  clk: pistachio: Fix PLL rate calculation in integer mode
  clk: pistachio: Fix override of clk-pll settings from boot loader
  clk: pistachio: Fix 32bit integer overflows
  clk: tegra: Fix some static checker problems
  clk: qcom: Fix MSM8916 prng clock enable bit
  clk: Add missing header for 'bool' definition to clk-conf.h
  drivers/clk: appropriate __init annotation for const data
  clk: rockchip: register pll mux before pll itself
  clk: add bindings for the Ux500 clocks
  clk/ARM: move Ux500 PRCC bases to the device tree
  clk: remove duplicated code with __clk_set_parent_after
  clk: Convert __clk_get_name(hw->clk) to clk_hw_get_name(hw)
  clk: Constify clk_hw argument to provider APIs
  clk: Hi6220: add stub clock driver
  dt-bindings: clk: Hi6220: Document stub clock driver
  dt-bindings: arm: Hi6220: add doc for SRAM controller
  clk: atlas7: fix pll missed divide NR in fraction mode
  clk: atlas7: fix bit field and its root clk for coresight_tpiu
  ...

7 files changed, 305 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
index c431c67524d6..c733e28e18e5 100644
--- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
+++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
@@ -127,6 +127,24 @@ Example:
 		#clock-cells = <1>;
 	};
 
+
+Hisilicon Hi6220 SRAM controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-sramctrl", "syscon"
+- reg : Register address and size
+
+Hisilicon's SoCs use sram for multiple purpose; on Hi6220 there have several
+SRAM banks for power management, modem, security, etc. Further, use "syscon"
+managing the common sram which can be shared by multiple modules.
+
+Example:
+	/*for Hi6220*/
+	sram: sram@fff80000 {
+		compatible = "hisilicon,hi6220-sramctrl", "syscon";
+		reg = <0x0 0xfff80000 0x0 0x12000>;
+	};
+
 -----------------------------------------------------------------------
 Hisilicon HiP01 system controller
 
diff --git a/Documentation/devicetree/bindings/arm/sp810.txt b/Documentation/devicetree/bindings/arm/sp810.txt
new file mode 100644
index 000000000000..6808fb5dee40
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/sp810.txt
@@ -0,0 +1,46 @@
+SP810 System Controller
+-----------------------
+
+Required properties:
+
+- compatible:	standard compatible string for a Primecell peripheral,
+		see Documentation/devicetree/bindings/arm/primecell.txt
+		for more details
+		should be: "arm,sp810", "arm,primecell"
+
+- reg:		standard registers property, physical address and size
+		of the control registers
+
+- clock-names:	from the common clock bindings, for more details see
+		Documentation/devicetree/bindings/clock/clock-bindings.txt;
+		should be: "refclk", "timclk", "apb_pclk"
+
+- clocks:	from the common clock bindings, phandle and clock
+		specifier pairs for the entries of clock-names property
+
+- #clock-cells: from the common clock bindings;
+		should be: <1>
+
+- clock-output-names: from the common clock bindings;
+		should be: "timerclken0", "timerclken1", "timerclken2", "timerclken3"
+
+- assigned-clocks: from the common clock binding;
+		should be: clock specifier for each output clock of this
+		provider node
+
+- assigned-clock-parents: from the common clock binding;
+		should be: phandle of input clock listed in clocks
+		property with the highest frequency
+
+Example:
+	v2m_sysctl: sysctl@020000 {
+		compatible = "arm,sp810", "arm,primecell";
+		reg = <0x020000 0x1000>;
+		clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>;
+		clock-names = "refclk", "timclk", "apb_pclk";
+		#clock-cells = <1>;
+		clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3";
+		assigned-clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&v2m_sysctl 3>, <&v2m_sysctl 3>;
+		assigned-clock-parents = <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>;
+
+	};
diff --git a/Documentation/devicetree/bindings/clock/gpio-mux-clock.txt b/Documentation/devicetree/bindings/clock/gpio-mux-clock.txt
new file mode 100644
index 000000000000..2be1e038ca62
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/gpio-mux-clock.txt
@@ -0,0 +1,19 @@
+Binding for simple gpio clock multiplexer.
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be "gpio-mux-clock".
+- clocks: list of two references to parent clocks.
+- #clock-cells : from common clock binding; shall be set to 0.
+- select-gpios : GPIO reference for selecting the parent clock.
+
+Example:
+	clock {
+		compatible = "gpio-mux-clock";
+		clocks = <&parentclk1>, <&parentclk2>;
+		#clock-cells = <0>;
+		select-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+	};
diff --git a/Documentation/devicetree/bindings/clock/hi6220-clock.txt b/Documentation/devicetree/bindings/clock/hi6220-clock.txt
index 259e30af9597..e4d5feaebc29 100644
--- a/Documentation/devicetree/bindings/clock/hi6220-clock.txt
+++ b/Documentation/devicetree/bindings/clock/hi6220-clock.txt
@@ -15,19 +15,36 @@ Required Properties:
 	- "hisilicon,hi6220-sysctrl"
 	- "hisilicon,hi6220-mediactrl"
 	- "hisilicon,hi6220-pmctrl"
+	- "hisilicon,hi6220-stub-clk"
 
 - reg: physical base address of the controller and length of memory mapped
   region.
 
 - #clock-cells: should be 1.
 
-For example:
+Optional Properties:
+
+- hisilicon,hi6220-clk-sram: phandle to the syscon managing the SoC internal sram;
+  the driver need use the sram to pass parameters for frequency change.
+
+- mboxes: use the label reference for the mailbox as the first parameter, the
+  second parameter is the channel number.
+
+Example 1:
 	sys_ctrl: sys_ctrl@f7030000 {
 		compatible = "hisilicon,hi6220-sysctrl", "syscon";
 		reg = <0x0 0xf7030000 0x0 0x2000>;
 		#clock-cells = <1>;
 	};
 
+Example 2:
+	stub_clock: stub_clock {
+		compatible = "hisilicon,hi6220-stub-clk";
+		hisilicon,hi6220-clk-sram = <&sram>;
+		#clock-cells = <1>;
+		mboxes = <&mailbox 1>;
+	};
+
 Each clock is assigned an identifier and client nodes use this identifier
 to specify the clock which they consume.
 
diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
new file mode 100644
index 000000000000..ee7e5fd4a50b
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
@@ -0,0 +1,79 @@
+NVIDIA Tegra124 DFLL FCPU clocksource
+
+This binding uses the common clock binding:
+Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+The DFLL IP block on Tegra is a root clocksource designed for clocking
+the fast CPU cluster. It consists of a free-running voltage controlled
+oscillator connected to the CPU voltage rail (VDD_CPU), and a closed loop
+control module that will automatically adjust the VDD_CPU voltage by
+communicating with an off-chip PMIC either via an I2C bus or via PWM signals.
+Currently only the I2C mode is supported by these bindings.
+
+Required properties:
+- compatible : should be "nvidia,tegra124-dfll"
+- reg : Defines the following set of registers, in the order listed:
+        - registers for the DFLL control logic.
+        - registers for the I2C output logic.
+        - registers for the integrated I2C master controller.
+        - look-up table RAM for voltage register values.
+- interrupts: Should contain the DFLL block interrupt.
+- clocks: Must contain an entry for each entry in clock-names.
+  See clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+  - soc: Clock source for the DFLL control logic.
+  - ref: The closed loop reference clock
+  - i2c: Clock source for the integrated I2C master.
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+  - dvco: Reset control for the DFLL DVCO.
+- #clock-cells: Must be 0.
+- clock-output-names: Name of the clock output.
+- vdd-cpu-supply: Regulator for the CPU voltage rail that the DFLL
+  hardware will start controlling. The regulator will be queried for
+  the I2C register, control values and supported voltages.
+
+Required properties for the control loop parameters:
+- nvidia,sample-rate: Sample rate of the DFLL control loop.
+- nvidia,droop-ctrl: See the register CL_DVFS_DROOP_CTRL in the TRM.
+- nvidia,force-mode: See the field DFLL_PARAMS_FORCE_MODE in the TRM.
+- nvidia,cf: Numeric value, see the field DFLL_PARAMS_CF_PARAM in the TRM.
+- nvidia,ci: Numeric value, see the field DFLL_PARAMS_CI_PARAM in the TRM.
+- nvidia,cg: Numeric value, see the field DFLL_PARAMS_CG_PARAM in the TRM.
+
+Optional properties for the control loop parameters:
+- nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE in the TRM.
+
+Required properties for I2C mode:
+- nvidia,i2c-fs-rate: I2C transfer rate, if using full speed mode.
+
+Example:
+
+clock@0,70110000 {
+        compatible = "nvidia,tegra124-dfll";
+        reg = <0 0x70110000 0 0x100>, /* DFLL control */
+              <0 0x70110000 0 0x100>, /* I2C output control */
+              <0 0x70110100 0 0x100>, /* Integrated I2C controller */
+              <0 0x70110200 0 0x100>; /* Look-up table RAM */
+        interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&tegra_car TEGRA124_CLK_DFLL_SOC>,
+                 <&tegra_car TEGRA124_CLK_DFLL_REF>,
+                 <&tegra_car TEGRA124_CLK_I2C5>;
+        clock-names = "soc", "ref", "i2c";
+        resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>;
+        reset-names = "dvco";
+        #clock-cells = <0>;
+        clock-output-names = "dfllCPU_out";
+        vdd-cpu-supply = <&vdd_cpu>;
+        status = "okay";
+
+        nvidia,sample-rate = <12500>;
+        nvidia,droop-ctrl = <0x00000f00>;
+        nvidia,force-mode = <1>;
+        nvidia,cf = <10>;
+        nvidia,ci = <0>;
+        nvidia,cg = <2>;
+
+        nvidia,i2c-fs-rate = <400000>;
+};
diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3368-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3368-cru.txt
new file mode 100644
index 000000000000..7c8bbcfed8d2
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/rockchip,rk3368-cru.txt
@@ -0,0 +1,61 @@
+* Rockchip RK3368 Clock and Reset Unit
+
+The RK3368 clock controller generates and supplies clock to various
+controllers within the SoC and also implements a reset controller for SoC
+peripherals.
+
+Required Properties:
+
+- compatible: should be "rockchip,rk3368-cru"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- #clock-cells: should be 1.
+- #reset-cells: should be 1.
+
+Optional Properties:
+
+- rockchip,grf: phandle to the syscon managing the "general register files"
+  If missing, pll rates are not changeable, due to the missing pll lock status.
+
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume. All available clocks are defined as
+preprocessor macros in the dt-bindings/clock/rk3368-cru.h headers and can be
+used in device tree sources. Similar macros exist for the reset sources in
+these files.
+
+External clocks:
+
+There are several clocks that are generated outside the SoC. It is expected
+that they are defined using standard clock bindings with following
+clock-output-names:
+ - "xin24m" - crystal input - required,
+ - "xin32k" - rtc clock - optional,
+ - "ext_i2s" - external I2S clock - optional,
+ - "ext_gmac" - external GMAC clock - optional
+ - "ext_hsadc" - external HSADC clock - optional,
+ - "ext_isp" - external ISP clock - optional,
+ - "ext_jtag" - external JTAG clock - optional
+ - "ext_vip" - external VIP clock - optional,
+ - "usbotg_out" - output clock of the pll in the otg phy
+
+Example: Clock controller node:
+
+	cru: clock-controller@ff760000 {
+		compatible = "rockchip,rk3368-cru";
+		reg = <0x0 0xff760000 0x0 0x1000>;
+		rockchip,grf = <&grf>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
+Example: UART controller node that consumes the clock generated by the clock
+  controller:
+
+	uart0: serial@10124000 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x10124000 0x400>;
+		interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <1>;
+		clocks = <&cru SCLK_UART0>;
+	};
diff --git a/Documentation/devicetree/bindings/clock/ux500.txt b/Documentation/devicetree/bindings/clock/ux500.txt
new file mode 100644
index 000000000000..e52bd4b72348
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/ux500.txt
@@ -0,0 +1,64 @@
+Clock bindings for ST-Ericsson Ux500 clocks
+
+Required properties :
+- compatible : shall contain only one of the following:
+  "stericsson,u8500-clks"
+  "stericsson,u8540-clks"
+  "stericsson,u9540-clks"
+- reg : shall contain base register location and length for
+  CLKRST1, 2, 3, 5, and 6 in an array. Note the absence of
+  CLKRST4, which does not exist.
+
+Required subnodes:
+- prcmu-clock: a subnode with one clock cell for PRCMU (power,
+  reset, control unit) clocks. The cell indicates which PRCMU
+  clock in the prcmu-clock node the consumer wants to use.
+- prcc-periph-clock: a subnode with two clock cells for
+  PRCC (programmable reset- and clock controller) peripheral clocks.
+  The first cell indicates which PRCC block the consumer
+  wants to use, possible values are 1, 2, 3, 5, 6. The second
+  cell indicates which clock inside the PRCC block it wants,
+  possible values are 0 thru 31.
+- prcc-kernel-clock: a subnode with two clock cells for
+  PRCC (programmable reset- and clock controller) kernel clocks
+  The first cell indicates which PRCC block the consumer
+  wants to use, possible values are 1, 2, 3, 5, 6. The second
+  cell indicates which clock inside the PRCC block it wants,
+  possible values are 0 thru 31.
+- rtc32k-clock: a subnode with zero clock cells for the 32kHz
+  RTC clock.
+- smp-twd-clock: a subnode for the ARM SMP Timer Watchdog cluster
+  with zero clock cells.
+
+Example:
+
+clocks {
+	compatible = "stericsson,u8500-clks";
+	/*
+	 * Registers for the CLKRST block on peripheral
+	 * groups 1, 2, 3, 5, 6,
+	 */
+	reg = <0x8012f000 0x1000>, <0x8011f000 0x1000>,
+	    <0x8000f000 0x1000>, <0xa03ff000 0x1000>,
+	    <0xa03cf000 0x1000>;
+
+	prcmu_clk: prcmu-clock {
+		#clock-cells = <1>;
+	};
+
+	prcc_pclk: prcc-periph-clock {
+		#clock-cells = <2>;
+	};
+
+	prcc_kclk: prcc-kernel-clock {
+		#clock-cells = <2>;
+	};
+
+	rtc_clk: rtc32k-clock {
+		#clock-cells = <0>;
+	};
+
+	smp_twd_clk: smp-twd-clock {
+		#clock-cells = <0>;
+	};
+};