Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for kernel v4.6.  There is quite a
  lot of interesting stuff going on.

  The patches to other subsystems and arch-wide are ACKed as far as
  possible, though I consider things like per-arch <asm/gpio.h> as
  essentially a part of the GPIO subsystem so it should not be needed.

  Core changes:

   - The gpio_chip is now a *real device*.  Until now the gpio chips
     were just piggybacking the parent device or (gasp) floating in
     space outside of the device model.

     We now finally make GPIO chips devices.  The gpio_chip will create
     a gpio_device which contains a struct device, and this gpio_device
     struct is kept private.  Anything that needs to be kept private
     from the rest of the kernel will gradually be moved over to the
     gpio_device.

   - As a result of making the gpio_device a real device, we have added
     resource management, so devm_gpiochip_add_data() will cut down on
     overhead and reduce code lines.  A huge slew of patches convert
     almost all drivers in the subsystem to use this.

   - Building on making the GPIO a real device, we add the first step of
     a new userspace ABI: the GPIO character device.  We take small
     steps here, so we first add a pure *information* ABI and the tool
     "lsgpio" that will list all GPIO devices on the system and all
     lines on these devices.

     We can now discover GPIOs properly from userspace.  We still have
     not come up with a way to actually *use* GPIOs from userspace.

   - To encourage people to use the character device for the future, we
     have it always-enabled when using GPIO.  The old sysfs ABI is still
     opt-in (and can be used in parallel), but is marked as deprecated.

     We will keep it around for the foreseeable future, but it will not
     be extended to cover ever more use cases.

  Cleanup:

   - Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
     includes.

     This dates back to when GPIO was an opt-in feature and no shared
     library even existed: just a header file with proper prototypes was
     provided and all semantics were up to the arch to implement.  These
     patches make the GPIO chip even more a proper device and cleans out
     leftovers of the old in-kernel API here and there.

     Still some cruft is left but it's very little now.

   - There is still some clamping of return values for .get() going on,
     but we now return sane values in the vast majority of drivers and
     the errorpath is sanitized.  Some patches for powerpc, blackfin and
     unicore still drop in.

   - We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
     implementations to use gpiochip_add_data() and cut down on code
     lines.

   - MPC8xxx is converted to use the generic GPIO helpers.

   - ATH79 is converted to use the generic GPIO helpers.

  New drivers:

   - WinSystems WS16C48

   - Acces 104-DIO-48E

   - F81866 (a F7188x variant)

   - Qoric (a MPC8xxx variant)

   - TS-4800

   - SPI serializers (pisosr): simple 74xx shift registers connected to
     SPI to obtain a dirt-cheap output-only GPIO expander.

   - Texas Instruments TPIC2810

   - Texas Instruments TPS65218

   - Texas Instruments TPS65912

   - X-Gene (ARM64) standby GPIO controller"

* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
  Revert "Share upstreaming patches"
  gpio: mcp23s08: Fix clearing of interrupt.
  gpiolib: Fix comment referring to gpio_*() in gpiod_*()
  gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
  gpio: xgene: Fix kconfig for standby GIPO contoller
  gpio: Add generic serializer DT binding
  gpio: uapi: use 0xB4 as ioctl() major
  gpio: tps65912: fix bad merge
  Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
  gpio: omap: drop dev field from gpio_bank structure
  gpio: mpc8xxx: Slightly update the code for better readability
  gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
  gpio: mpc8xxx: Fixup setting gpio direction output
  gpio: mcp23s08: Add support for mcp23s18
  dt-bindings: gpio: altera: Fix altr,interrupt-type property
  gpio: add driver for MEN 16Z127 GPIO controller
  gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
  gpio: timberdale: Switch to devm_ioremap_resource()
  gpio: ts4800: Add IMX51 dependency
  gpiolib: rewrite gpiodev_add_to_list
  ...

6 files changed, 147 insertions, 12 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-altera.txt b/Documentation/devicetree/bindings/gpio/gpio-altera.txt
index 12f50149e1ed..826a7208ca93 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-altera.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-altera.txt
@@ -12,7 +12,7 @@ Required properties:
 - #interrupt-cells : Should be 1. The interrupt type is fixed in the hardware.
   - The first cell is the GPIO offset number within the GPIO controller.
 - interrupts: Specify the interrupt.
-- altr,interrupt-trigger: Specifies the interrupt trigger type the GPIO
+- altr,interrupt-type: Specifies the interrupt trigger type the GPIO
   hardware is synthesized. This field is required if the Altera GPIO controller
   used has IRQ enabled as the interrupt type is not software controlled,
   but hardware synthesized. Required if GPIO is used as an interrupt
@@ -35,7 +35,7 @@ gpio_altr: gpio@0xff200000 {
 	reg = <0xff200000 0x10>;
 	interrupts = <0 45 4>;
 	altr,ngpio = <32>;
-	altr,interrupt-trigger = <IRQ_TYPE_EDGE_RISING>;
+	altr,interrupt-type = <IRQ_TYPE_EDGE_RISING>;
 	#gpio-cells = <2>;
 	gpio-controller;
 	#interrupt-cells = <1>;
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
index f3332b9a8ed4..c934106b10aa 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
@@ -10,6 +10,7 @@ Required properties:
 
     - "microchip,mcp23s08" for  8 GPIO SPI version
     - "microchip,mcp23s17" for 16 GPIO SPI version
+    - "microchip,mcp23s18" for 16 GPIO SPI version
     - "microchip,mcp23008" for  8 GPIO I2C version or
     - "microchip,mcp23017" for 16 GPIO I2C version of the chip
     NOTE: Do not use the old mcp prefix any more. It is deprecated and will be
@@ -43,9 +44,6 @@ Optional properties:
   - first cell is the pin number
   - second cell is used to specify flags.
 - interrupt-controller: Marks the device node as a interrupt controller.
-NOTE: The interrupt functionality is only supported for i2c versions of the
-chips. The spi chips can also do the interrupts, but this is not supported by
-the linux driver yet.
 
 Optional device specific properties:
 - microchip,irq-mirror: Sets the mirror flag in the IOCON register. Devices
diff --git a/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt b/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt
new file mode 100644
index 000000000000..414a01cdf715
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt
@@ -0,0 +1,34 @@
+Generic Parallel-in/Serial-out Shift Register GPIO Driver
+
+This binding describes generic parallel-in/serial-out shift register
+devices that can be used for GPI (General Purpose Input). This includes
+SN74165 serial-out shift registers and the SN65HVS88x series of
+industrial serializers.
+
+Required properties:
+ - compatible		: Should be "pisosr-gpio".
+ - gpio-controller	: Marks the device node as a GPIO controller.
+ - #gpio-cells		: Should be two. For consumer use see gpio.txt.
+
+Optional properties:
+ - ngpios		: Number of used GPIO lines (0..n-1), default is 8.
+ - load-gpios		: GPIO pin specifier attached to load enable, this
+			  pin is pulsed before reading from the device to
+			  load input pin values into the the device.
+
+For other required and optional properties of SPI slave
+nodes please refer to ../spi/spi-bus.txt.
+
+Example:
+
+	gpio@0 {
+		compatible = "ti,sn65hvs882", "pisosr-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		load-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+		spi-cpol;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-ts4800.txt b/Documentation/devicetree/bindings/gpio/gpio-ts4800.txt
new file mode 100644
index 000000000000..92ea9c8f6399
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-ts4800.txt
@@ -0,0 +1,20 @@
+* TS-4800 FPGA's GPIO controller bindings
+
+Required properties:
+- compatible: Must be "technologic,ts4800-gpio".
+- #gpio-cells: Should be two. The first cell is the pin number.
+- reg: Physical base address of the controller and length
+       of memory mapped region.
+
+Optional property:
+- ngpios: See "gpio.txt"
+
+Example:
+
+gpio1: gpio {
+	compatible = "technologic,ts4800-gpio";
+	reg = <0x10020 0x6>;
+	ngpios = <8>;
+	gpio-controller;
+	#gpio-cells = <2>;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
index dae130060537..5490c1d68981 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
@@ -1,10 +1,20 @@
 APM X-Gene Standby GPIO controller bindings
 
-This is a gpio controller in the standby domain.
-
-There are 20 GPIO pins from 0..21. There is no GPIO_DS14 or GPIO_DS15,
-only GPIO_DS8..GPIO_DS13 support interrupts. The IRQ mapping
-is currently 1-to-1 on interrupts 0x28 thru 0x2d.
+This is a gpio controller in the standby domain. It also supports interrupt in
+some particular pins which are sourced to its parent interrupt controller
+as diagram below:
+                            +-----------------+
+                            | X-Gene standby  |
+                            | GPIO controller +------ GPIO_0
++------------+              |                 | ...
+| Parent IRQ | EXT_INT_0    |                 +------ GPIO_8/EXT_INT_0
+| controller | (SPI40)      |                 | ...
+| (GICv2)    +--------------+                 +------ GPIO_[N+8]/EXT_INT_N
+|            |   ...        |                 |
+|            | EXT_INT_N    |                 +------ GPIO_[N+9]
+|            | (SPI[40 + N])|                 | ...
+|            +--------------+                 +------ GPIO_MAX
++------------+              +-----------------+
 
 Required properties:
 - compatible: "apm,xgene-gpio-sb" for the X-Gene Standby GPIO controller
@@ -15,10 +25,18 @@ Required properties:
 		0 = active high
 		1 = active low
 - gpio-controller: Marks the device node as a GPIO controller.
-- interrupts: Shall contain exactly 6 interrupts.
+- interrupts: The EXT_INT_0 parent interrupt resource must be listed first.
+- interrupt-parent: Phandle of the parent interrupt controller.
+- interrupt-cells: Should be two.
+       - first cell is 0-N coresponding for EXT_INT_0 to EXT_INT_N.
+       - second cell is used to specify flags.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- apm,nr-gpios: Optional, specify number of gpios pin.
+- apm,nr-irqs: Optional, specify number of interrupt pins.
+- apm,irq-start: Optional, specify lowest gpio pin support interrupt.
 
 Example:
-	sbgpio: sbgpio@17001000 {
+	sbgpio: gpio@17001000{
 		compatible = "apm,xgene-gpio-sb";
 		reg = <0x0 0x17001000 0x0 0x400>;
 		#gpio-cells = <2>;
@@ -29,4 +47,19 @@ Example:
 				<0x0 0x2b 0x1>,
 				<0x0 0x2c 0x1>,
 				<0x0 0x2d 0x1>;
+		interrupt-parent = <&gic>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		apm,nr-gpios = <22>;
+		apm,nr-irqs = <6>;
+		apm,irq-start = <8>;
+	};
+
+	testuser {
+		compatible = "example,testuser";
+		/* Use the GPIO_13/EXT_INT_5 line as an active high triggered
+		 * level interrupt
+		 */
+		interrupts = <5 4>;
+		interrupt-parent = <&sbgpio>;
 	};
diff --git a/Documentation/devicetree/bindings/mfd/tps65912.txt b/Documentation/devicetree/bindings/mfd/tps65912.txt
new file mode 100644
index 000000000000..717e66d23142
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/tps65912.txt
@@ -0,0 +1,50 @@
+* TPS65912 Power Management Integrated Circuit bindings
+
+Required properties:
+ - compatible		: Should be "ti,tps65912".
+ - reg			: Slave address or chip select number (I2C / SPI).
+ - interrupt-parent	: The parent interrupt controller.
+ - interrupts		: The interrupt line the device is connected to.
+ - interrupt-controller	: Marks the device node as an interrupt controller.
+ - #interrupt-cells	: The number of cells to describe an IRQ, should be 2.
+			    The first cell is the IRQ number.
+			    The second cell is the flags, encoded as trigger
+			    masks from ../interrupt-controller/interrupts.txt.
+ - gpio-controller	: Marks the device node as a GPIO Controller.
+ - #gpio-cells		: Should be two.  The first cell is the pin number and
+			    the second cell is used to specify flags.
+			    See ../gpio/gpio.txt for more information.
+ - regulators:		: List of child nodes that specify the regulator
+			    initialization data. Child nodes must be named
+			    after their hardware counterparts: dcdc[1-4] and
+			    ldo[1-10]. Each child nodes is defined using the
+			    standard binding for regulators.
+
+Example:
+
+	pmic: tps65912@2d {
+		compatible = "ti,tps65912";
+		reg = <0x2d>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		regulators {
+			dcdc1 {
+				regulator-name = "vdd_core";
+				regulator-min-microvolt = <912000>;
+				regulator-max-microvolt = <1144000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1900000>;
+				regulator-max-microvolt = <1900000>;
+			};
+		};
+	};