Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux

Pull clk updates from Stephen Boyd:
 "This is all driver updates, the majority of which is a bunch of new
  Qualcomm clk drivers that dominate the diffstat because we add support
  for six SoCs from that particular vendor.

  The other big change is the removal of various clk drivers that are no
  longer used now that the kernel is dropping support for those SoCs.

  Beyond that there's the usual non-critical fixes for existing drivers
  and a good number of patches from Lee Jones that cleanup a bunch of
  W=1 enabled builds.

  Removed Drivers:
   - Remove efm32 clk driver
   - Remove tango4 clk driver
   - Remove zte zx clk driver
   - Remove sirf prima2/atlast clk drivers
   - Remove u300 clk driver

  New Drivers:
   - PLL support on MStar/SigmaStar ARMv7 SoCs
   - CPU clks for Qualcomm SDX55
   - GCC and RPMh clks for Qualcomm SC8180x and SC7280 SoCs
   - GCC clks for Qualcomm SM8350
   - GPU clks for Qualcomm SDM660/SDM630

  Updates:
   - Video clk fixups on Qualcomm SM8250
   - Improvements for multimedia clks on Qualcomm MSM8998
   - Fix many warnings with W=1 enabled builds under drivers/clk/
   - Support crystal load capacitance for Versaclock VC5
   - Add a "skip recall" DT binding for Silicon Labs' si570 to avoid
     glitches at boot
   - Convert Xilinx VCU clk driver to a proper clk provider driver
   - Expose Xilinx ZynqMP clk driver to more platforms
   - Amlogic pll driver fixup
   - Amlogic meson8b clock controller dt support clean up
   - Remove mipi clk from the Amlogic axg clock controller
   - New Rockchip rk3368 clock ids related to camera input
   - Use pr_notice() instead of pr_warn() on i.MX6Q pre-boot ldb_di_clk
     reparenting
   - A series from Liu Ying that adds some SCU clocks support for
     i.MX8qxp DC0/MIPI-LVDS subsystems
   - A series from Lucas Stach that adds PLL monitor clocks for i.MX8MQ,
     and clkout1/2 support for i.MX8MM/MN
   - Add I2c and Ethernet (RAVB) clocks on Renesas R-Car V3U
   - Add timer (TMU) clocks on most Renesas R-Car Gen3 SoCs
   - Add video-related (FCPVD/VSPD/VSPX), watchdog (RWDT), serial
     (HSCIF), pincontrol/GPIO (PFC/GPIO), SPI (MSIOF), SDHI, and DMA
     (SYS-DMAC) clocks on Renesas R-Car V3U
   - Add support for the USB 2.0 clock selector on Renesas RZ/G2 SoCs
   - Allwinner H616 SoC clk support"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (171 commits)
  clk: mstar: msc313-mpll: Fix format specifier
  clk: mstar: Allow MStar clk drivers to be compile tested
  clk: qoriq: use macros to generate pll_mask
  clk: qcom: Add Global Clock controller (GCC) driver for SC7280
  dt-bindings: clock: Add SC7280 GCC clock binding
  clk: qcom: rpmh: Add support for RPMH clocks on SC7280
  dt-bindings: clock: Add RPMHCC bindings for SC7280
  clk: qcom: gcc-sm8350: add gdsc
  dt-bindings: clock: Add QCOM SDM630 and SDM660 graphics clock bindings
  clk: qcom: Add SDM660 GPU Clock Controller (GPUCC) driver
  clk: qcom: mmcc-msm8996: Migrate gfx3d clock to clk_rcg2_gfx3d
  clk: qcom: rcg2: Stop hardcoding gfx3d pingpong parent numbers
  dt-bindings: clock: Add support for the SDM630 and SDM660 mmcc
  clk: qcom: Add SDM660 Multimedia Clock Controller (MMCC) driver
  clk: qcom: gcc-sdm660: Mark GPU CFG AHB clock as critical
  clk: qcom: gcc-sdm660: Mark MMSS NoC CFG AHB clock as critical
  clk: qcom: gpucc-msm8998: Allow fabia gpupll0 rate setting
  clk: qcom: gpucc-msm8998: Add resets, cxc, fix flags on gpu_gx_gdsc
  clk: qcom: gdsc: Implement NO_RET_PERIPH flag
  clk: mstar: MStar/SigmaStar MPLL driver
  ...

1 files changed, 0 insertions, 73 deletions

diff --git a/Documentation/devicetree/bindings/clock/prima2-clock.txt b/Documentation/devicetree/bindings/clock/prima2-clock.txt
deleted file mode 100644
index 5016979c0f78..000000000000
--- a/Documentation/devicetree/bindings/clock/prima2-clock.txt
+++ /dev/null
@@ -1,73 +0,0 @@
-* Clock bindings for CSR SiRFprimaII
-
-Required properties:
-- compatible: Should be "sirf,prima2-clkc"
-- reg: Address and length of the register set
-- interrupts: Should contain clock controller interrupt
-- #clock-cells: Should be <1>
-
-The clock consumer should specify the desired clock by having the clock
-ID in its "clocks" phandle cell.  The following is a full list of prima2
-clocks and IDs.
-
-	Clock			ID
-	---------------------------
-	rtc			0
-	osc             	1
-	pll1            	2
-	pll2            	3
-	pll3            	4
-	mem             	5
-	sys             	6
-	security        	7
-	dsp             	8
-	gps             	9
-	mf              	10
-	io              	11
-	cpu             	12
-	uart0           	13
-	uart1           	14
-	uart2           	15
-	tsc             	16
-	i2c0            	17
-	i2c1            	18
-	spi0            	19
-	spi1            	20
-	pwmc            	21
-	efuse           	22
-	pulse           	23
-	dmac0           	24
-	dmac1           	25
-	nand            	26
-	audio           	27
-	usp0            	28
-	usp1            	29
-	usp2            	30
-	vip             	31
-	gfx             	32
-	mm              	33
-	lcd             	34
-	vpp             	35
-	mmc01           	36
-	mmc23           	37
-	mmc45           	38
-	usbpll          	39
-	usb0            	40
-	usb1			41
-
-Examples:
-
-clks: clock-controller@88000000 {
-	compatible = "sirf,prima2-clkc";
-	reg = <0x88000000 0x1000>;
-	interrupts = <3>;
-	#clock-cells = <1>;
-};
-
-i2c0: i2c@b00e0000 {
-	cell-index = <0>;
-	compatible = "sirf,prima2-i2c";
-	reg = <0xb00e0000 0x10000>;
-	interrupts = <24>;
-	clocks = <&clks 17>;
-};